Search Documents

By Arthur Crowfoot

As a result of work done, on an operating scale, in its experimental mill during 1920 and 1921, the plan here given was proposed for crushing, grinding, and concentrating low-grade sulfide ores at the Morenci Branch of the Phelps Dodge Corpn. The flow sheet is designed to recover 85 per cent. of the total copper and 95 per cent. of the sulfide copper from ore assaying 2.0 per cent. total copper and 0.3 per cent. acid soluble copper. At present, 1400 tons are treated daily under the conditions of this flow sheet, two 700-ton units having been installed in the 4000-ton concentrator. The run-of-mine ore will be reduced, in the dry-crushing plant, to —6 mesh and then delivered to the concentrator feed bins. The crushing will be done in three stages: (I) Run-of-mine ore is reduced to —2 1/2-in. in a gyratory crusher; (2) the 3-in. ore is reduced to 1/2-in. in 72 by 24 in. rolls; (3) the 1/2-in. ore is reduced to — 6-mesh size in 54 by 24 in. rolls. The 54-in. rolls will operate in closed circuit with electrically vibrated screens, "Hum-mer" type, a conveyor circuit being used to carry the roll product to the screens. Sufficient screens will be installed to pass 1.5 tons undersize per hour per square foot. Fine-ore bin chutes will be piped for compressed air, which will be used intermittently to keep the ore feed in motion if it tends to arch or pipe in the bins. The Concentrator The concentration of the copper and iron sulfides in the ore will be effected in three stages: I. By direct treatment of the —6-mesh crushing-plant product on primary tables, which will recover about 35 per cent. of the original copper content of the ore in a clean granular concentrate. The table middling will be dewatered in Dorr rake classifiers and ground to — 48-mesh in ball mills operating in closed circuit with circulating classifiers.

Jan 1, 1923

By C. R. Breck

THERE has been a running discussion over the-past several years with respect to the life and adequacy of our natural gas reserves.. Some of the experts agree on one phase of the subject at least--that eventually it will be necessary to augment deliveries of natural gas in the northern markets by the development of a more or less comparable synthetic gas made from coal. The purpose of this paper is to point out: 1. It may be later than a good many people think-the demand for additional domestic and commercial pipeline gas in at least one section of the North will probably be felt rather keenly before an adequate synthetic pipeline-gas project, developed on economic lines, could be completed, even if ' initiated in the near future. 2. The evidence is considerable that such a project would be technically sound and economically self-supporting, although the margin of profit at first might be so small and the magnitude of an economic enterprise so great that financing would be impossible without Government aid in some form or other. The part of the country referred to is the heavily populated section in the northeast of the United States. To simplify an examination of the situation, let us take the potential marketing areas within range to the north and east of the three pipelines: 1. Tennessee Gas Transmission Co. as it enters Erie County, New York state. 2. Texas Eastern Transmission Corporation just before the tap that supplies the general Philadelphia area. 3. Transcontinental G& Pipe Line Corporation as it enters the state of New Jersey The sources of gas for these three pipelines are in Texas and Louisiana. The ultimate maximum combined capacity of the three lines at the points stated is approximately 1,200,000,000 cu ft per 24 hr at the maximum load factor probable of attainment in normal operation. The areas supplied by the three lines north and east of the points stated, or assumed as eventual markets, are: 1. Central New York state, from Buffalo to Albany (both inclusive).

Jan 1, 1953

By R. V. Wheeler

A matter of much concern at present to the coal-mining industry of Great Britain is the effect of the working of the Coal Mines Act, 1930. This Act, which received the Royal Assent on Aug. 1, 1930, contains five parts: (1) production, supply and sale of coal; (11) the reorganization of the coal-mining industry; (111) hours of work; (IV) the Coal Mines National Industrial Board; (V) general. The first three parts are of major interest and discussion can be confined to them. Part I.—Production, Supply and Sale of Coal Under Part I of the Coal Mines Act, 1930, provision is made for central and district schemes to regulate the production, supply and sale of coal by the fixation of standard tonnage, quota and minimum prices. By Nov. 1, 1930, all the district schemes came into force with the exception of that for Scotland, where the majority of the coal-owners did not see their way to accept the amendments to their draft scheme demanded by the Mines Department. A compulsory scheme for Scotland was thereupon prepared by the Mines Department and put into force on Nov. 24, 1930. It is administered by the coal-owners of the district. The essence of the schemes is the allocation of tonnage for each district by a Central Council, and the allocation of quota for each pit in a district by an Executive Board for that district. Up to Dec. 31, 1930, the various bodies of coal-owners engaged in administering the schemes were employed in work preliminary to their full operation. Standard tonnages had to be determined and coals had to be classified. In consequence, it was not found possible to put the regulation of output into force until Jan. 1, 1931. The determination of minimum prices proved to be an even longer process, and only in a few districts were minimum price schedules operative during the first quarter of this year. The working of the schemes during the March quarter, 1931, has been reviewed in an official publication by the Mines Department,' which can be summarized as follows:

Jan 1, 1932

By L. P. Teas

Although 1930 has been a year of stagnation, proration and curtailment, the Gulf Coast has measured up to its tradition in the matter of interesting and significant discoveries. Only 2 domes and 7 new structural areas were brought into the producing column in 1930, whereas, in 1929, 13 domes and one structure were added to this list, yet a total of 14 new producing horizons were proved on various domes and structures. On 5 domes new flanks were successfully tested for commercial production. The year 1930 has shown at Barber's Hill that oil in commercial quantities may exist below salt or cap. Numerous wells have been drilled through cap, or even salt itself, into good producing sands. The past year has been particularly notable in the interest and in the number of deep holes drilled. Two wells have gone below 8000 ft. in each of the states of Texas and Louisiana, and in the two states together 14 wells have gone below 7000 ft At the beginning of the year only one well was producing below 6000 ft. in coastal Texas, while at its end, 19 wells were producing or had produced. Geophysical discoveries and activity on the Coast have waned and this type of work has moved further inland. The peaks of production at Pettus, Barber's Hill, Raccoon Bend, Refugio, Orchard and at Humble, in Texas; and at Lake Barre, Port Barre, Black Bayou, White Castle and Vinton in Louisiana, were seen this year. These were new peaks for Humble and Vinton, of course, these fields having previously gone through periods of peak flank production. In Table 1 the completions listed are for the entire month of December in both years. It is remarkable that in 1930, a year of overproduction and proration, there were actually more wildcat operations at its end than at the end of 1929; but it is gratifying that the operations in the proven fields were exactly one-half what they had been at the end of 1929. The price of A grade coastal crude, or oil below 25" Bé., has been cut from $1.30 at the beginning of the year to $1.00 at its close; and B grade, or oil above 25o Bé., has been reduced from a price range of $1.15 to $1.63 down to a range of from $0.75 to $1.22. In spite of these reductions there has been no proration program on the Coast. Systematic

Jan 1, 1931

By T. M. Allen, W. H. White

THE Greenwood-Grand Forks area of southern central British Columbia, known as the Boundary District, has a long history of mining exploration and production. At the turn of the century this was the premier copper mining camp in the British Empire, its total production amounting to some 20 million tons. Most of this ore came from the great Granby mines at Phoenix, but the Motherlode mine at Deadwood camp, 6 miles to the west, and several mines in Summit camp, 5 miles north of Phoenix, made important contributions. The large deposits were exhausted in 1918 and the district since has seen only desultory exploration and salvage operations. The orebodies are mineralized skarn zones in limestone members of a thick series of Upper Paleozoic sedimentary and volcanic strata. Chalcopyrite is the primary ore-mineral. Copper carbonates and silicates occur sparingly in outcrops, but the oxidized zone generally is very shallow. Much of the surface is mantled by glacial drift which in most places ranges in thickness from 2 to 15 ft. In some of the hanging valleys, however, the glacial drift may be as much as 100 ft thick and may assume drumlin-like forms. In 1951 an ambitious program aimed at the discovery of new orebodies and important extensions of abandoned deposits was launched by Attwood Copper Mines, Ltd. In this district so thoroughly searched by an earlier generation of prospectors, any orebody which had remained undiscovered must have little or no surface indication. Consequently, in addition to the basic detailed geological work, the program of exploration included magnetometer and self-potential surveys. Geological bets and geophysical anomalies were tested further, prior to diamond drilling, by a study of copper distribution in tree twigs and/or in the soil. The soil sampling and analytical methods used and some of the results seem of sufficient importance to warrant this paper. The authors had done some plant sampling in this and other districts, using the dithizone neutral-color-end-point method (Warren and Delavault, 1948, 1949; White, 1950),1-3 but they were unfamiliar with its soil application. Finally, after much experimenting in the field, they adopted the methods described here. These methods are not entirely original or defensible on theoretical grounds, but under field conditions of rapid sampling and analysis the results are reliable enough to be of use. Fig. 1, which shows the results of duplicate analyses of duplicate soil samples taken at 50-ft intervals across an anomalous zone, indicates the relative dependability both of the sampling and analytical methods. Sampling and Analytical Equipment A 2-ft piece of 1-in. solid drill steel, one end sharpened to a broad, conical point. The steel is marked at 1 ft from the point. A 2-ft piece of ½-in. black iron pipe, one end filed to a bevelled cutting edge. The pipe is marked at 1 ft 3 in. from the cutting end. A 3-lb hammer. A plastic or rubberized sheet about 18 in. square. Moisture-proof assay pulp envelopes. A 10-mesh seive made from window screen with the paint burnt off. A small assay spatula. A pan balance sensitive to 10 mg. Two ignition trays about 4 in. square, made of sheet iron turned up along the edges. A Coleman two-burner gasoline stove. An asbestos board about 5x8 in., used as a hot plate on the gasoline stove. A circular aluminum rack to hold 8 test tubes while refluxing (design of Almond and Morris). Pyrex Glassware Large refluxing test tubes, 25x200 mm, marked at 40 ml volume. Breakers, 20 ml. Pipettes, 1, 5, and 10-ml capacity. Graduate, 50 ml. Shaking cylinders, 100 ml, glass stoppers. Burette, 25 or 50-ml capacity, with holder. Chemical Supplies 1 N sulphuric acid. Hydroxylamine hydrochloride, solid crystals. Fisher Alkacid test paper. Copper standard solution. Dithizone standard solution 60 mg per liter. Water reasonably free of metals. Soil Sampling Method: The problem of how to take a soil sample is extremely crucial. The method outlined below, adopted after a number of tests, has the advantages of uniform pattern, uniform depth, and uniform size of sample. The area to be tested was marked off by chain and compass lines 100 ft apart, normal to the strike of possible ore deposits. Numbered stakes were set at 50-ft intervals along these lines and a soil sample was taken at each stake in the following manner. The drill steel was driven into the ground normal to the slope of the surface to the marked depth of 1 ft, moved slightly from side to side, then carefully withdrawn. The iron pipe was inserted to the bottom of this hole, tapped down to the marked depth of 1 ft 3 in. and withdrawn; the 3-in. soil plug in the

Jan 1, 1955

By John Blatchford, H. O. Hofman

The leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which, according to Pélabon,' is 550°C., according to Wagemann2 540°C., and according to Borgstroma 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343", if 0.1 to 0.2 mm.; and 430" if 0.2 mm. 3. The fusibility of a mixture of Sb2S33 and Sb203 which in the form of kermesite (Sb2S3)z.Sbz03 melts at 517°C.6 4. The volatility of Sb2Ss and SbzOs, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures. As regards the oxidation of metallic antimony, we have the experimental evidence of C. F. Plattner6 that when fused and brought to a red heat, it burns with a bluish-white flame to Sb2Oa which passes off as a

Jan 1, 1916

By M. T. Abasov

The work suggests an approach to the problem of optimally planning the drilling and development of gas fields. The approach is based on systems analysis and allows a joint optimal choice of the total number of wells in the field, their spacing in the reservoir, the diameter of production tubing, drilling dynamics, the number and spacing of drilling platforms and well pattern schemes for each plat- form as well. The optimal solution satisfies the set of technical- economical requirements and provides a minimum value of discounted total expenditures (capital costs plus operating costs). A mathematical model of the problem is presented. This work represents an extension of the authors&apos; previous investigations that formulated and solved problems of optimal drilling of oil and gas deposits by directional wells [1] and problems of optimal control of the number of active wells in multi-reservoir oil and gas fields [2], [3]. For construction of the mathematical model we choose a range (Nmin, Nmax) of possible values of the total number of wells, N, which should be drilled in the deposit. Here Nmin, Nmax are minimum and maximum numbers of wells correspondingly, that should be drilled into the reservoir. N[€](Nmin = N1, ... N[o], ..., Nm = Nmax). For simplicity a one-reservoir gas field is considered. It is assumed that: (a) wells are spaced in the reservoir uniformly, (b) there is a certain algorithm providing a uniform spacing of the given number N[o] ([0]=l, . . . , m) of wells in the reservoir, (c) the diameters of the production tubing for all the wells are the same. The relation Qz (x), i.e. the dependence of the cumulative output of gas from the cumulative "well-years" of operations is constructed for each diameter dZ from the given range of diameters d1< ...< dr.

Jan 1, 1977

By R. O. Day, R. S. Dean

In constructing a theory of the flow and hardening of metals, v necessarily make use of such phenomena as seem to be universal1 observed in metals. It is, therefore, a matter of concern to the con structors of such mnemonic systems if one or two of the group classific as metals show anomalous behavior. Such egregious phenomena observed in pure or nearly pure iron in the reaction of its mechanic properties to low-temperature annealing after cold work and to increase temperature of testing. In short it has been generally observcd tha iron, as an outstanding exception among metals, increases its hardnes and strength by low-temperature annealing after cold work,&apos; and alt by increase of testing temperature to the range of 150" to 300" C. The investigation here recorded was made then with the object ( ascertaining if similar phenomena were observed in high-purity iro and, if not, to the presence of which impurities these phenomena coul be traced. Experimental Procedure Three kinds of iron were taken for a study of hardening by rehcatin after cold work: 1. Vacuum-melted electrolytic iron; melted in an Arsem furnace in a magnesia crucible. That this iron was of high purity is indicated b a magnetic permeability above 20,000. 2. Electrolytic iron melted in air in a small laboratory furnace. 3. Armco iron, commercial material. These materials in the form of forged bars, annealed at 980" C. in vacuum, were reduced 30 per cent. in thickness by cold rolling and the reheated to temperatures varying from 100&apos; to 500&apos; C. The Rockwe hardness number was measured after each treatment. The results and shown in Fig. 1, curves 1, 2 and 3.

Jan 1, 1929

ARTHUR PHILLIPS,* Bridgeport, Conn. (written discussion?).-It is to, be regretted that the very valuable paper by Messrs. Bassett and Davis did not appear in the early war period. The data presented would have been of inestimable service to inspectors, of cartridge brass who, admittedly, had little or no knowledge regarding the relation of grain size to temperature of anneal, and no real appreciation of, the significance of the Brinell hardness test. The paper is of considerable interest to, metallurgists also. WALTER R. HIBBARD, ? Bridgeport. Conn. (written discussion§).-The writer has carefully studied Messrs. Bassett and Davis&apos;s paper with considerable interest, inasmuch as our laboratory has tested cartridge brass by means of a Brinell machine. In March, 1917, at the suggestion of the Technical Department of the American Brass Co., we started a comparison of grain-size measurements and Brinell hardness of-cartridge brass with a gage of 0.1 in. or greater. This was continued until March, 1918, when we adopted the Brinell hardness test as standard for brass 0.1 in. gage or greater, and discontinued grain-size measurements upon this metal. The data collected during the test showed that the Brinell hardness indicated more accurately how the metal acted in actual working operations. It was also more reliable because two manipulators check themselves closer by the Brinell test than by the grain-size measurements. It also consumed less time in making the tests. Alfred V. de Forest, formerly assistant research engineer of our laboratories, has described the apparatus and some of the checking results in a paper read June, 1918, before the American Society for Testing Materials.1 The writer hopes that a more satisfactory. method for testing cartridge brass and gilding in gages thinner than 0.1 in. may be devised than the present method of grain-size measurements.

Jan 3, 1919

By Paul Weir

DURING the past decade, methods of producing bituminous coal in the State of Illinois, which ranks third in production among the states in which bituminous coal is mined, have undergone great changes. From less than one million tons in 1923, the strip-mine production has gradually increased to a high of 11,725,870 tons in 1937. From a negligible amount prior to 1927, the amount of coal mechanically loaded underground had increased to a high of 28,374,362 tons in 1937. The amount manually loaded in 1937 reached a low of 12,332,023 tons. In this same year, this state ranked first in strip-mine production, also in mechanically loaded production. For this reason a study of the influence of mechanization on location of production in Illinois may be helpful in anticipating what may happen in other producing states. The reason for the changes in methods lies in the differences in costs of production. The Bureau of Research and Statistics of the National Bituminous Coal Commission has made public the following costs of pro-duction by various methods in the State of Illinois (district 10) for the last nine months of 1937: all mines, $1.7602 per ton; strip mines, $1.4319; mechanical loading mines, $1.7457; hand loading mines, $2.1793; all underground mines, $1.8703. These are weighted averages for the entire district. Inasmuch as production in 1937 was reported from 58 counties scattered over two-thirds of the area of the state and from five different seams varying in thickness from less than 3 ft. to as much as 12 ft., it is apparent that the location of production must be influenced by the extent of mechanization possible in the various producing counties.

Jan 1, 1939

By A. E. Back, S. F. Ravitz

When manganese ores are leached with sulphur dioxide, a large part of any zinc in the ore usually is extracted with the manganese.1 In the dithionate process,2,3 in which the manganese ore is leached with dilute sulphur dioxide gas and the manganese is subsequently precipitated by adding lime to the pregnant solution, the zinc is precipitated with the manganese. These facts suggested the possibility of applying the dithionate process to the recovery of zinc from oxidized ores or calcined sulphide concentrates. Accordingly, an investigation was begun, and preliminary tests were made on several ores and concentrates. The results were encouraging, but the need to devote available funds and personnel to other projects made it necessary to drop the work before the various factors involved in the process could be studied in detail. A brief mention of the process,4 however, elicited a number of inquiries, so that it appeared desirable to report the results of the preliminary work. The dithionate process as applied to zinc may be summarized briefly as follows: The ore or calcined concentrate is leached with dilute SO2 gas to dissolve the zinc, largely as zinc sulphate, in accordance with the following equation in which [ZnO] represents the "oxide zinc" in the ore or calcine: [ZnO] + SO2(g) + 1/2 O2 = Zn++SO4— [1] If, in the leaching step, the ore or calcine is suspended in calcium dithionate solution, the sulphate ion, as it is formed, is precipitated immediately as calcium sulphate, which is subsequently filtered off with the insoluble ore residue: Zn++SO4— + Ca++S2O6— = CaSO4(s) + Zn++S2O6- [2] An alternative procedure is to suspend the ore in water, filter off the insoluble ore residue after leaching, add calcium dithionate to the resulting zinc sulphate solution, and then filter off the calcium sulphate precipitate. In either event the zinc is obtained in the form of a pregnant solution of zinc dithionate, from which it can be precipitated as relatively pure zinc hydroxide by adding milk of lime: Zn++S2O6— + Ca(OH), = Zn(OH)2(s) + Ca++S2O6- [3] The zinc hydroxide precipitate is calcined to form the final zinc oxide product: Zn(OH)2 = ZnO(s) + H2O(g) [4] Theoretically the process is completely cyclic with respect to dithionate ion, the calcium dithionate required for reaction 2 being replaced by that formed in reaction 3. In practice, of course, small amounts of dithionate would be lost in the various filter cakes, depending on the economic washing limits. In the leaching step, however, some of the SO2 is oxidized to dithionale instead of sulphate, accord- ing to the following overall reaction: ZnO + 2SO2(g) + 1/2 O2(g) = Zn++S2O6-, [5] so that the dithionate losses are made up, at least in part. Ores and Concentrates Tested The analyses of the ores and concentrates tested are summarized in Table 1, which also includes the analyses of the calcines produced from the concentrates. The concentrates were roasted in a laboratory muffle furnace at the temperatures indicated until evolution of SO2 could no longer be detected; shallow clay dishes ordinarily were used; but calcines 2a and 2c were prepared in iron dishes, with the result that these two calcines were badly contaminated with iron scale. The "complex" concentrate, sample 1, consisted essentially of sphalerite grains containing inclusions of pyrite and other sulphide minerals too minute to be liberated by grinding within economic limits. In the " marmatitic" concentrate, sample 2, the iron was present largely as marmatite (that is, as iron sulphide in solid solution in zinc sulphide) rather than as pyrite inclusions. The zinc was present largely as the carbonate in the two "oxidized" ores, samples 3 and 4, and as the silicate in the "willemite" ore, sample 5. Leaching Tests The leaching cell was a 3-liter glass beaker placed in an electrically heated water bath manually controlled to maintain a temperature of 35°C in the leach slurry. The slurry was agitated by means of a flat paddle-type stirrer

Jan 1, 1950

By C. E. Ells, A. Sawatzky

The effect of neutron irradiation on tensile properties of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy has been evaluated for integrated neutron fluxes up to 3 x 1020 n per sq cm (E > 1 Mev). Specimen temperature during irradiation was normally 300°C. The material was studied both in annealed and in quenched and aged conditions. When the alloy (fab-ricatedfrom sponge zirconium) is quenched from a temperature =40°C below the a + ß/ß transformation and aged 6 hr at 535oC, neutron irradiation up to the maximum studied has little effect 071 reduction in area, although there is a drop in uniform elongation and the yield strength is increased by = 25 pct. Conversely, irradiation of the alloy in an annealed condition can result in much greater changes in properties, with yield-strength increases of up to 200 pet. The dose dependence of irradiation hardening obeys the saturation equntion proposed by Makin and Minter to explain hardening in copper and nickel: Act = C[1 - exp(-Døt)/1/2 A rnodel is proposed to explain the effect of niobium content and metallurgical condition on irradiatiotz behavior. THE Zr-Nb alloys form a class of material susceptible to marked strengthening by quench and age heat treatment. With niobium concentrations as low as 2.5 wt pet, strengths can be developed which are double those of annealed zircaloy-2.1 Since the neutron-capture cross section of the Zr-2.5 wt pet Nb alloy is nearly identical to that of Zircaloy-2, significant gains in power-reactor neutron economy could be obtained by replacing stressed in-reactor components of Zircaloy-2 with the heat-treated Zr-Nb alloy. When the solution heat-treatment temperature is in the high (a + ß) phase, then the tensile properties of the quenched (and aged at 500°C) material have been shown to be relatively insensitive to neutron irradiation.1-3 Addition of small quantities of copper to the binary Zr-2.5 wt pet Nb alloy gives a useful reduction to the corrosion rate in air and carbon di- oxide,&apos; and a ternary alloy of composition Zr-2.5 wt pet Nb-0.5 wt pet Cu was chosen for one component in the Douglas Point Reactor. This application utilizes both the corrosion resistance to a moist air-carbon dioxide environment and the strength developed by a quench and age heat treatment. By suitable choice of solution heat treatment and aging temperatures, tensile properties of the ternary alloy can be made nearly identical to those considered as optimum for the binary alloy. One effect of the copper addition, however, is to give marked changes in the aging kinetics of the alloy.&apos; For this reason, it appeared that neutron irradiation might promote overaging in the ternary alloy, particularly at the elevated service temperature (=300°C). This paper describes the effect of neutron irradiation on the tensile behavior of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy in several metallurgical conditions pertinent to its use as a reactor material. The metallurgical conditions included those for which aging occurs in the unirradiated material, and fully annealed conditions for which a higher degree of thermal stability could be expected. 1) EXPERIMENTAL Two batches of alloy were used, both made from sponge zirconium. The fabricator&apos;s analysis of principle constituents showed no significant difference between the two batches, Table I. The rod material was rolled to 1.5 in. diam, and then swaged to final sizes of 0.5 to 0.375 in. diam at nominal temperatures of 785" and 625°C for the AM and AS batches, respectively. Subsequent hydrogen analyses at CRNL confirmed that the hydrogen concentration of the as-received rod was indeed <20 ppm. However, it was found that the (a + ß)/ß transus for the AM material was approximately 25°C lower than that of the AS material, indicating rather more difference in oxygen concentration than given in Table I. Except for a small difference in yield-point behavior, the tensile prop-

Jan 1, 1965

By Howard A. Meyerhoff

IN western Argentina, in the Province of Mendoza and the Territory of Neuquén, there is a series of solid bitumen deposits which are claimed to be the most extensive in the world. In a linear belt 500 km (311 miles) long, roughly paralleling the axis of the Andes but occupying a variety of positions with respect to the orogenic structures, more than 100 outcrops have been reported. Approximately 70 of these have been prospected, and some mining has been planned or attempted for about half this number. Limited tonnage, high sulphur content, inaccessibility, labor shortages, and disastrous fires have taken a heavy toll among these operations, and in 1947, only 4 deposits were being actively mined, but 8 more were being explored and developed with a view to placing them in production. Inasmuch as these deposits are currently yielding a substantial fraction of Argentina&apos;s limited domestic supply of solid fuels, a brief account of the deposits and of the small industry based upon them will provide a commentary on Argentina&apos;s fuel problem. CHARACTER OF SOLID BITUMENS The solid bitumens of Mendoza and Neuquén are petroleum derivatives, as is indicated by the following ultimate analysis: [CONSTITUENTS PER CENT Hydrogen6.8 Carbon82.4 Nit.rogenI.6 Oxygen2.7 Sulphur2.2 Ash4.3 100.0] In physical appearance they bear a close resemblance to coal and are commonly called carbón. Their specific gravity has an extreme range of 1.10 to 1.777 in 36 samples weighed, but the average is between 1.14 and 1.24. The material is black, lustrous to dull, with blocky to sub-conchoidal fracture. Though brittle, the purest material is softer than anthracite and exhibits slightly more cohesion. This bituminous material is generally known as asfaltita or asphaltite, but definitive chemical studies indicate that the term asphaltite or grahamite can be applied correctly only to the exceptionally pure material of the Auca Mahuida district in Neuquén. Some other name should be used for the chemically variable bitumens found in all other districts, and the designation "asphaltitic pyrobitumen" has been proposed by Carlos A. S. Piscione.1 At the present time these bitumens, are finding favor as solid fuel and as a gas-producing medium. They yield heat values of 8650 to 9750 cal,2 or 14,500 to 16,750 Btu per pound, and in consequence of their excellent heating qualities and the scarcity of imported coal, they are marketed as far away as Buenos Aires at a price of go to 95 pesos, or approximately $22 to 23, per metric ton. In burning, the material swells and decomposes into solid, fluid, and gaseous fractions which burn violently though nonexplosively. Its combustibility has been responsible for disasters and virtually complete destruction at Mina La Esperanza and Mina Santa Marta, and for minor mishaps elsewhere, as at Mina Escondida in August 1947.

Jan 1, 1947

By Jeff Steinhoff

INTRODUCTION The Henderson mine utilizes a highly mechanized, continuous, panel-caving, mining system to extract ore from a deep, massive, molybdenite deposit. The mine is located 80.5 km (50 miles) west of Denver, Colorado. The mine surface facilities are located 3,170 m (10,400 feet) above sea level in a steep valley on the eastern side of the Continental Divide. Milling facilities are 24 km (15 miles) west on the western side of the divide at an elevation of 2,804 m (9,200 feet) above sea level. The ore- body is located approximately 3,000 feet south of the valley under Red Mountain. Access to the ore for men and materials is through a 915 m (3,000-foot) deep, 8.5 m (28-foot) diameter, vertical, concrete-lined, service shaft. Access from the mill is through a 15.5 km (9.6-mile) rail haulage tunnel. The mine is ventilated through an additional intake shaft and two exhaust shafts. Mine production at this time is 27,255 mtpd (30,000 stpd). The mine ventilation system supplies 1,038 cubic meters per second (2.2 million cfm) through approximately 60 miles of drifting or 2.7 tons of air per ton of ore mined. There are 130 fans in the mine in fixed locations and in vent lines with 6,900 connected horsepower in the mine. MINING METHOD AND LAYOUT The orebody is divided vertically into two major zones. The upper zone is the 8100-level production area. The bottom zone is the 7700- level production area which is in the early development stage. The rail haulage level at 7500 feet is common to both production zones. Each mine production zone consists of five associated sublevels. The cave undercut level is 16.8 m (55 feet) above the production level. Two boundary cutoff levels are located 44.2 m (145 feet) and 62.5 m (205 feet) respectively above the production level. The fresh-air level is positioned 15.2 m (50 feet) below the production level, and the exhaust vent level is 19.8 m (65 feet) below the production level. Horizontally, each production zone is divided into three panels each, 224 m (800 feet) wide. These panels are caved from south to north. As the caving in one panel nears completion, caving in the adjacent panel is initiated. Development for the caving panels is continuous so that the sublevels above the production level and the production level itself have a combination of development drifting and production-related activities. UNDERGROUND VENTILATION NETWORK The ventilation system is zoned in the same manner as the orebody itself. One major split of 600 cubic meters per second (1,270,000 cfm) ventilates the 8100-level production zone; one split of 100 cubic meters per second (210,000 cfm) ventilates the development of the 7700- level production zone; and one split of 165 cubic meters per second (350,000 cfm) ventilates the 7500 rail haulage level. The haulage tunnel requires an additional 188 cubic meters per second (400,000 cfm) of air. Development-drift ventilation is accomplished by hanging 1.0 m (3.5-foot) diameter steel ducting in the drifts with 40-horsepower, 0.96 m (38-inch) diameter fans supplying 9.4 cubic meters per second (20.000 cfm). The normal maximum length for these systems is 300 m (1,000 feet). The 8100-level production-area ventilation system is especially suited to a high level of mucking activity confined in a small area. Approximately 93 per cent of the mine&apos;s total production is transferred from the drawpoints to ore passes in 10 production drifts. The active area in each drift is 300 m (1,000 feet). Twelve 5-cubic-yard LHD units with Cat turbo- charged 170-horsepower engines are assigned to the area. Under these conditions, more than one LHD is assigned to a particular production drift. Adequate ventilation is maintained by making an air change every 97 m (320 feet) along the production drifts. Fresh air is brought into the production drifts from the fresh-air level through 1.37 m (4.5-foot) diameter raises. Air travels south along the production drift to the ore pass where it is exhausted down the ore pass to the exhaust level. The ore pass is followed by another intake which is followed by an ore-pass exhaust. At the south end of the production area, a series of exhaust fans maintain a southerly air- flow through the production level.

Jan 1, 1981

By John W. Crutchfield, Emil F. Bowers

This paper presents the initial results of a pressure maintenance by water return project in the Lower Pawelek reservoir of the Falls City Field, Karnes County, Southwest Texas. Production is from the Lower Wilcox section at an average depth of 6,030 ft on the downthrown side of a "down to the coast" fault. Of particular interest is that the reservoir oil is high gravity and low viscosity but far undersaturated with gas at the original reservoir pressure and temperature. The early pressure and production history indicated only a partial or limited water drive, and this fact, coupled with the characteristics of the reservoir fluid and artificial lifting problem.. made advisable the water injection program to maintain reservoir pressure. The paper includes a description of the reservoir and reservoir fluids, the pressure and production history, a description of the water injection facilities, and the results of reservoir calculations involving Hurst&apos;s unsteady state flow and the material balance equations for calculation of water influx and prediction of the pressure-production relationship at various rates of withdrawal. The reservoir calculations and initial field results indicate that reservoir pressures in excess of 85 per cent of original pressure can be maintained by control of water injection even at very high rates of production. INTRODUCTION The purpose of this paper is to report the initial results of a pressure maintenance by water return program in the Lower Pawelek reservoir, Falls City Field, Karnes County. Texas, and to calculate an empirical relationship between pressure and production in this limited or partial water drive reservoir. Location The Falls City Field (Fig. 1) is located two miles north of the town of Falls City in Karnes County, Texas, and is approximately 50 miles south-southeast of San Antonio on U. S. Highway 181. Discovery and Development The initial block of leases was taken after a surface geological survey identified a major east-west fault and closure on the south or downthrown section. The discovery well, Southern Minerals Corporation&apos;s Joe F. Bartosch 1; was completed at 4,650 ft in the Lower Bartosch sand in December, 1944. Drilling was continuous until December, 1946, and resulted in the discovery of 12 oil reservoirs between 4,600 and 6,050 ft in the Middle and Lower Wilcox formations. These are shown on the cross-section (Fig. 2). As of the current date there are 64 oil wells completed as follows: Southern Gulfshore Magnolia Minerals Oil Petroleum Reservoir Corp. Co. Corp. Total Upper Bartosch 0 0 0 0 Lower Bartosch 16 0 0 16 Shulze 7 0 1 8 Upper Faires 2 0 0 2 Lower Faires 4 0 0 4 Upper Moczygemba 0 0 0 0 Lower Moczygemha 2 0 0 2 Olinick 2 0 0 2 Upper Martinez 0 0 0 0 Lower Martinez 5 0 0 5 Upper Pawelek 0 0 1 Lower Pawelek 27 1 3 31 Total 65 2 4 71

Jan 1, 1950

By J. W. Martin, L. K. Singhal

Grain boundary M23CB precipitates have been shown to form by a process involving the migration of an austenite grain boundary, and each plate of precipitate is in parallel orientation with one of the austenite grains constituting the boundary. The carbide distribution and morphology appear to be sensitive to grain boundary mis orientation. Some areas of austenite grain bowzdary permit the development of an array of M,C, particles, some of which are in parallel orientation with one grain and some with the other grain constituting the boundary. Massive carbide at grain boundary triple points is also shown to be in parallel orientation with one constituent grain. PREFERENTIAL precipitation during aging of carbides of the type (Fe,Cr)23C6, usually written MZ3C6, in grain boundaries of quenched austenitic stainless steels has been widely recognized. M23C6 has a complex cubic crystal structure&apos; which contains ninety-two metal atoms and twenty-four carbon atoms per unit cell. Less energy is involved in forming grain boundary precipitates than in the formation of intragranular precipitates, and the process is further enhanced by the accelerated diffusion rates in the boundaries and by the probability of segregation of chromium atoms and carbon atoms to the region of the grain boundaries during prior solution heat treatment in order to reduce lattice strain. Early electron micrographic studies2, 3 involving either extraction replica or normal replica techniques established the geometric or dendritic form of the carbide particles, although this approach led to dis- pute as to whether the particles grew within the plane of the boundary or grew into the matrix.4-6 More recent thin-foil studies&apos; have claimed to identify a discontinuous precipitation process involving M23C6 at grain boundaries, and the object of the present work was to attempt to clarify the situation using modern electron micrographic and diffraction techniques. 1) EXPERIMENTAL 1.1) Material. The steel selected for this work had a base composition of 24 pct Ni-25 pct Cr-3 pct Ti and contained about 0.04 pct C. The full analysis if given in Table I. This alloy was in the form of strip which had been hot- and cold-rolled to a thickness of 0.6 mm. 1.2) Heat Treatment. Specimens 4 cm long by 1 cm wide were solution-heat-treated for 3 hr in argon at 1150°C, followed by water-quenching. Specimens were subsequently aged in vacuo at 750°C for periods up to 500 hr. 1.3) Preparation of Electron Microscope Specimens. The heat-treated strips were cut bv spark machining into discs of 3 mm diam and 0.6 mm thickness. he-discs were dished on both sides using an electrolytic jet of 15 pct HCl electrolyte at 80 v. Final electro-polishing of the discs was carried out using 10 pct perchloric acid, 20 pct glycerol, and 70 pct ethanol at 10 v. The current density was kept below 300 ma. cm"2 by cooling the electrolyte to 0" to 5°C. As soon as a small hole appeared, the electropolishing was stopped and the specimen was quickly washed with ethanol.

Jan 1, 1969

By Dwight C. Roberts, Stender Sweeney

The spacing of wells in Long Beach oil field has caused much discussion from the earliest days of its development, on account of the closely drilled town-lot areas which have been as intensively developed as any productive areas in the world. The purpose of this paper is to present the results obtained from this type of development in comparison with the more widely spaced development in this field, now that a sufficient length of productive life has elapsed. The intensity of development in Long Beach is indicated by the fact that up to Sept. 1, 1929, there were 1736 wells either drilled or drilling. Of these 165 failed to get production and 121 were drilling. Thus 1450 wells have produced oil from an area of 1350 acres. Up to July 1, 1929, these wells produced a total of 35.5,047,913 barrels. Method Pursued Four groups of offset areas were chosen, in each group the wells in one area are widely spaced and in the other, closely spaced. The areas in each group are contiguous and the groups are spread over the field from the southeast end to the northwest, so that representative data are assured. The comparison has also been extended to shallow and deep zones, like zones in their respective areas being compared. Even though these productive zones are very thick, a fair picture of results is obtained, because the drilling of the wells in the two types of areas was concurrent in the different groups and, as a rule, the thickness of sand opened up at any one time was about the same. As deeper sands were found, wells in offset areas were deepened or new ones were drilled in both types of areas. The division of zones was made in the same manner in contiguous areas. The total cumulative production up to July 1, 1929, of the wells in their respective zones in each area was obtained. From these figures were computed the recovery per well, recovery per acre, acreage per well, and the ratios of these factors. Thus July 1, 1929, is the end of the period considered in all areas.

Jan 1, 1930

By J. C. Irvine

Meramec Mining Co., a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp., is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge mine near Sullivan, Mo., about 70 mi southwest of St. Louis. The orebody lies under about 1300 ft of sediments. It is tabular, about 2600 ft long and up to 600 ft thick, and lies in an approximate east-west delineation. The orebody dips about 80"s and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite. The Precambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 ft 1 in. diam and 2500 ft deep. No. 1 shaft, equipped with an "A" type head-frame and conventional cylindrical drums, hoists men, materials, and waste rock; it is also the downcast air shaft. No. 2 shaft utilizes tower-mounted friction hoists to handle the two production skips, each with 24-ton counterweights, and a small man cage. The mine exhaust passes through this shaft. Ore is principally mined by sublevel stoping,

Jan 9, 1972

By J. H. Smith, H. W. Paxton

ALTHOUGH many structural and kinetic investigations have been made for alloys of iron and nickel, only meager data exist from thermodynamic investigations. The purpose of this note is to estimate the free energy of the Fe-Ni solid solutions from thermodynamic data available for ternary alloys containing iron and nickel. The lack of a description of the thermodynamic behavior for the Fe-Ni system has required the structural and kinetic analyses of the system to assume some form of solution behavior, usually regular, e.g., the mar-tensite transformation analysis of Kaufman and Cohen, 1 consistent with the limited thermodynamic data. Indications that this system could exhibit ideal solution departures might have been suggested by the large deviations from additivity rules observed in the density and lattice-parameter measurements of Jette and Foote2 who interpreted this in terms of possible solute-solvent interactions. Later Turkdogan et al. 3 and more recently Ward and wright 4 found a minimum in the graphite solubility in liquid Fe-Ni solutions near the concentration of FeNi3 with deviations from linearity persisting at all concentrations. This was interpreted by Ward and wright4 to indicate negative heats of solution and was suggestive of short-range ordering. The infinitely dilute activity coefficient of carbon (?oC) was also observed by smith5 to pass through a maximum near the FeNi3 concentration in Fe-Ni solid solutions. Recent investigations of the liquid solutions over the entire concentration range by Zellars et a1.&apos; and Speiser et a1.," using vapor-pressure determinations, revealed both negative departures from Raoult&apos;s law and a nonregular solution behavior. The solid alloys have been studied by Oriani 8 and Kubaschew-ski and von Goldbeck6 employing gaseous H2/H2O equilibria with Fe and FeO. Both investigations were in substantial agreement, indicating very small departures from ideality. However, Oriani observed the formation of Fe3O4 (instead of FeO) at XFe= 0.441 which severed the equilibrium and precluded experimental investigation of the nickel-rich alloys. Heat-capacity and heat-content measurements have been evaluated by Montgomery10 and found generally unsatisfactory for gleaning thermodynamic information. This is due to the unknown final states of the alloys caused by the interference of the martensite transformation on cooling iron-rich concentrations and superlattice formation, magnetic transformation, and the varied heat treatments used by investigators of nickel-rich concentrations. As an alternative to the experimental difficulties, indirect estimates of the solid-solution behavior have been made by Fleischer and Elliott11 and Smith et a1.12 From their measurements of the solubility of Fe-Ni alloys in liquid lead, Fleischer and Elliott calculated the nickel activity (aNi) (and integrated for aFe) by assuming: 1) liquid lead has no solubility in solid Fe-Ni alloys, 2) Henry&apos;s law is obeyed throughout the liquid lead-rich phase (0— 12 at. pct Nil, and 3) Henry&apos;s law constant is independent of relative iron and nickel concentrations. The estimate of Smith et a1.12 was obtained

Jan 1, 1964

By Pradeep K. Rohatgi, Clyde M. Adams

Structures produced upon solidification of the eu-tectic composition (33 wt pct Cu) aluminum copper alloy have been examined as a function of freezing rate dfs /d? , the rate of change of fraction solid (fs) with time (8). Slow (dfs/d? = 0.0016 sec-1), intermediate (dfs/d? = 0.02 sec-1) and rapid (dfs/d? = 0.4 to 7.30 sec-1) freezing rates were used. The lamellar Al-Cual2 eutectic is arranged in the form of rod-shaped colonies at rapid freezing rates. The colonies are aligned parallel to the direction of heat flow, whereas the lamellae within the colonies are aligned at various angles, as high as 90 deg, to the direction of heat flow. The colony spacing (C) is proportional to the square root of inverse freezihg rate. The relationship is C = 15.5(dfs/d?)-1/2 where C is in µ and 8 is in sec. The ratio of colony spacing to lamellar spacing is greater than 20.0 and increases with a decrease in the freezing rate. A duplex dendritic structure is produced at intermediate freezing rates. A fine lamellar eutectic is arranged within the dendrites (exhibiting side branches at an angle close to 60 deg from the main stem) and a coarse irregular eutectic appears in the interdendritic regions. The duplex eutectic structure is also produced at slow freezing rates. However, at slow freezing rates there is a Platelat of CuAl2, along the center of the main stem of each dendrite and the other lamellae are arranged perpendicular to the central platelet. THE eutectic between CuA12 and a! aluminum has been reported to freeze in a lamellar form by several workers.&apos;-3 chadwick4 has measured the interlamel-lar spacing as a function of growth rate. Kraft and Albright2 have reported on irregularities in the lamellar structures, and have proposed growth models which account for the formation of faults during solidification. In certain instances the lamellar eutectic has been found to exist in colonies. The colony formation315 has been attributed to the breakdown of a planar liquid-solid interface due to rejection of impurities. The aim of the present work is to study the structures produced from the eutectic aluminum-copper alloy under relatively fast solidification rates, such as encountered in casting and welding operations. The solid-liquid interface presumably remains planar under conditions of slow unidirectional freezing which produce lamellae aligned parallel to the direction of heat flow. The local growth velocities are the same over the entire interface and are equal to the rate of growth of the all-solid region. The spacing between the eutectic lamellae is inversely proportional to the square root of the growth rate of the all-solid region. Under the freezing conditions used in the present study, the solid-liquid interface is cellular or dendritic and the local growth velocities are different in the different regions of the interface. The relationship between the growth rate of the all solid region and the local growth velocities varies with the location and the shape of the interface. The growth rate of the all-solid region is, therefore, an inadequate parameter to describe the eutectic micro-structures which depend upon the local growth velocities. For this reason the structures have been examined as a function of freezing rate, dfs/d?, where fs is the fraction solidified at time 0. The freezing rate was varied by a factor of 4000. The relationship between the freezing rate, dfs/d?, and the growth velocit of the all solid region depends upon the specimen geometry and the shape of the interface. EXPERIMENTAL PROCEDURES The A1-33 pct Cu alloy used throughout this study was made in an induction furnace, using electrolytic copper and aluminum of commercial purity (99.7 pct), the primary impurities being silicon (0.12 pct), iron (0.14 pct), and zinc (0.02 pct). Three ranges of freezing rates were investigated: 1) A spectrum of rapid freezing rates (ranging from 0.40 to 7.30 sec-1) was obtained in arc deposits made on 2-in. thick cast plates of the eutectic alloy. The arc was operated at constant power and was made to travel at constant velocity on the surface of the plate that was in contact with the chill surface during solidification. The pool of liquid metal formed under the moving tungsten arc solidified rapidly by heat extraction through the unmelted plate. Conditions of unidirectional heat flow were achieved near the fusion zone interface, especially in the center of the arc deposits. The great advantage of the arc technique is that rapid cooling and freezing rates can be varied in a qualitative way. The correlation between the arc parameters and the solidification rate is given by the following relationship:6-8

Jan 1, 1970