Search Documents

By Alexandre Mussard

How do you make a mine out of 500 000 kg (1.1 million lb) of uranium oxide contained in a low-grade deposit with high clay content? Confronted with these limited reserves and mineralogical problems at France's St. Pierre du Cantal uranium deposit, engineers adopted a rather unusual mill process to keep capital costs to a minimum. Crushing and grinding were eliminated by using a high pressure monitor to slurry ore directly from stockpiles. After mechanical separation of the high-grade fines from low-grade sand, the sand fraction is washed of clay to increase permeability and then it is heap leached. Fines are sent to agitated vessels for acid leaching, and the pulp from this operation is diluted by pregnant solution from the heap leaching.

Jan 10, 1979

By David G. Chedgy, Wen L. Chen, Bill S. Taylor

Theoretically the heavy medium cyclone is capable of cleaning raw coal from a top size of about 38 mm (1 1/2 in.) to a bottom size of about 200 mesh. With this idea, plants have been built recently using the heavy medium cyclone without desliming. The full size range down to zero is fed into the cyclone. Products + 28 mesh are removed in the normal manner on drain and rinse screens. The 28 x 200 mesh products are recovered separately from the magnetic separator tailings. Simplicity of flowsheet and plant operation coupled with the high efficiency of the heavy medium cyclone makes this a very attractive approach.

Jan 1, 1980

By V. F. Zackay, W. A. Goering

ALLOYS of iron and aluminum up to 35 wt pct aluminum are single-phase solid solutions, and are of potentially wide applicability.1-3 In spite of early and continued interest1-4 little progress has been made until recently in the preparation and evaluation of sound alloys containing more than 6 wt pct aluminum. Vacuum-melting techniques for the production of ductile Fe-A1 alloys have been described recently.1-7 A. procedure for air melting these alloys is presented here. Low-carbon iron is induction melted without a slag in a rammed magnesia crucible. At the beginning of melt-down, aluminum pig (99.95 pct Al), charged in a clay-graphite bottom-pouring crucible is placed in a pot furnace at 1800°F. The primary deoxidation of the molten iron after melt-down is effected by the addition of 0.1 pct aluminum and 0.5 pct manganese. (Hilty and Crafts" have reported a significant increase in the deoxidation efficiency of the aluminum and manganese combination over that of the aluminum alone.) A more drastic deoxidation designed to reduce the oxyen content to the lowest possible level is accomplished by plunging metallic calcium to the bottom of the melt. This is done by wiring small cubes of the metal to a steel rod. A circular shield larger than the diameter of the crucible opening is attached to the rod so that any spa'ttering of the molten metal will not endanger the operator. Since the temperature of the molten metal is above the boiling point of calcium, the bath is vigclrously purged by calcium vapor. It is believed that the calcium-vapor treatment permits a homogeneous distribution of calcium in the melt. Owing to the vigor of the reaction the temperature of the molten metal should be kept below 2900°F prior to the calcium addition. A total of 0.05 pct calcium is added in two stages in this manner. The second calcium deoxidation is made just before charging the molten aluminum into the iron, in order that an excess of calcium be present for the remainder of the melt. The aluminum, which has been removed from the holding furnace, is then hydrogen degassed by bubbling chlorine through a quartz tube immersed in the molten aluminum. The hydrogen-chlorine reaction is an exothermic one preventing the solidification of the aluminum during the 5-min chlorination. Approximately 0.1 pct calcium, based on the amount of aluminum, is then added to the aluminum. A further excess of calcium is introduced into the melt in this manner. The oxide dross is removed, fluorspar is added to the molten iron, and the molten aluminum is poured through the fluorspar slag. The fluorspar should be dried thoroughly prior to its use, as any water present will react with the aluminum. Aluminum oxide formed during the pouring operation reacts with the fluorspar slag to form gaseous aluminum fluoride and calcium oxide. A forced-draft ventilating system is required for this operation as aluminum fluoride is toxic. As soon as the molten aluminum has been added, vigorous manual stirring of the melt is required because the slag-aluminum oxide reaction is highly exothermic and tends to take place near the top of the melt. The combination of high temperature and the slagging action of the fluorspar quickly erodes the crucible at the slag line if the aluminum is not stirred uniformly into the melt. It has been found that at least 4 min of manual stirring combined with induction stirring are necessary to ensure homogeneity. The power is shut off 1 min prior to pouring to allow metal and slag to separate. As much slag as possible is removed from the melt, which is then poured directly into cast-iron molds. A mold wash of aluminum oxide is used to prevent ingot sticking. For slab ingots which are to be rolled into sheet, a carbon-tetrachloride vapor atmosphere or a chlorinated-pitch mold wash is desirable, as the aluminum oxide formed in the pouring operation is subsequently removed by the chlorine in the presence of carbon." As in vacuum melting, a pouring temperature of about 2900°F is recommended. Adequate hot-topping is important as iron-aluminum ingots are subject to very deep piping. Ingots are removed from the molds and buried in vermiculite, where they are allowed to cool slowly to room temperature. The ingots are radiographed,

Jan 1, 1959

By Walter Kauenhowen

The production of crude oil in Germany during 1933 totaled about 1,669,521 bbl., a slight increase over the 1,608,558 bbl. produced in 1932. This is an extension of a yearly increase which has continued uninterruptedly since 1928. The 1933 increase in production is due chiefly to developments in the Nienhagen field. The production of the Wietze and Oberg fields remained rather stable, while the Oelheim-Eddesse and Volkenroda fields showed decreases. Nienhagen Field.—This field furnished about 61 per cent of the total German oil production in 1933. Most of the drilling activity centered the north district near the village of Nienhagen, where the trend of

Jan 1, 1934

By J. P. G. Farr, R. Brownsword

THE role of solute segregation in the formation of cellular solidification substructures in tin and its dilute alloys is well-established, see, e.g., Ref. 1. Segregation has been shown to persist during cooling, enabling solidification structures to be studied from sections taken at some distance behind the interface. In the present work, a single crystal of commercial nickel, 99.965 pct, was examined in this way. The crystal was cut from the center of a rod given a single pass in an electron beam floating zone melter. Polished sections of a nickel specimen taken normal to the growth direction showed a very fine precipitate phase, the distribution of which varied over the section. The identification of the phase proved difficult because of the small amount present and the small particle size, about 1 p: but it was shown by probe microanalysis to contain only nickel and oxygen in detectable concentrations and was probably nickel oxide, NiO. Bulk analysis of the material before melting showed there to be only 3 to 4 ppm of oxygen present, thus demonstrating a very considerable segregation concentration effect. In some areas of the section the precipitate formed a discontinuous hexagonal network suggesting decoration of the cellular boundaries known to be present in the sample2 whereas in a restricted region the precipitate formed small clusters. Occasionally it could be seen that the clusters were at the intersections of an hexagonal network of cellular dimension. It was suggested3 that this was the result of enhanced segregation to the cell boundary intersections whereas general cell boundary segregation was insufficient to give a precipitate. Enhanced nodal segregation has since been demonstrated in a number of systems.1, 4-8 The development of a suitable electrolytic etching technique (perchloric acid 20 pct v/v; ethyl alcohol 70 pct; glycerol 10 pct; current below electropolishing plateau; 1 to 2 sec etching) suggested the association of the phase with regions of solute segregation (where ko < 1); in these regions anodic attack produced grooves or depressions. In a study of the variation of solidification substructures with degree of constitutional supercooling, Biloni et a1.&apos; appear to have used standard growth conditions and varied the solute concentration. They were able to produce in a series of individual tin crystals examples of substructure ranging from planar interface through various cellular structures to den- Fig. 1—Electroetched section taken normal to the rod axis; the center of the rod lies to the left and the periphery to the right of the micrograph. The variation of structure across the section is evident. Magnification 60 times. drites. It was possible in the present nickel crystal to observe a continuous range of substructures varying with degree of supercooling across a single section as shown in Fig. 1. Growth rate, 13 mm per min, and temperature gradient were essentially constant; the variation in structure is thought to be due to a radial gradient in solute concentration ahead of the solid interface. The liquid at the interface is likely to have been richer in solute toward the periphery of the zone, the result of curvature of this interface. The type of substructure was seen to vary with increasing constitutional supercooling as follows: a) region free of precipitate. top left, Fig. 1: 6) region of nodal precipitates which became arranged in hexagons on passing from the center of the rod: c) irregular hexagonal cells with incomplete boundary precipitation; d) regular hexagonal cells of decreasing size with complete boundary precipitation. Fig. 2 shows the transition from stage 6 and Fig. 3 shows the structure in stage d. Within stage 0, the range of conditions over which irregularly positioned nodes occur appears to be small and the nodes are soon recognizable as taking up positions at the intersections of an hexagonal network as the supercooling increases.

Jan 1, 1970

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By J. H. Anderson, G. A. Parks, B. K. Jindal

Both temperature and humidity are important variables in electrical separations. By independent control of temperature and water vapor pressure, it is shown that charge depends primarily upon relative humidity, not on temperature or water pressure alone. All the effects of temperature changes other than modification of humidity are apparently small. However, humidity control can be achieved through manipulation of the more tractable variable, temperature. Both temperature and humidity are important variables in electrical separations. Some of their effects have been described in general by Fraas1,2 and by Ralston.3 The influence of temperature and humidity may be considered a problem in industrial separations because humidity, especially, is not normally controlled, hence leads to unpredicted quality control problems. The problem is significant whether the separation is based on conductivity differences or on contact electrification. There is no doubt that water adsorbs from humid atmospheres onto mineral surfaces resulting in conductivity changes.&apos;-8 An empirical relationship between conductivity and humidity is1.4-6,8 where a and b are constants peculiar to the substrate, and s and h are the conductivity and relative humidity respectively. Some authors have taken advantage of differences in a and b among minerals to make or propose electrodynamic separations in which h is the key control variable. Fraasl,2 reported that the charge developed on quartz and feldspar through contact with aluminum is sensitive to humidity, as illustrated schematically in Fig. 1. Lawver9 found that the charge developed by quartz on contact with several materials was tem-

Jan 1, 1967

By R. D. Pehlke, J. V. Gluck, R. L. Louvet

A study has been made of the effect of small additions of bismuth on the activity of zinc in dilute solution in molten tin. Free-energy interactions have previously been determined between zinc and various third elements where the solvents were molten bismuth or molten lead.&apos;-4 In both of these solvents, the activity of zinc exhibits a strong positive deviation from ideal behavior (at 550°C y° for zinc in lead is 11.4 and for zinc in bismuth is 3.0). The present work, using tin as the solvent, is an extension to a case where the positive deviation is considerably diminished (y°Zn at 550°C is 1.63). Several previous investigators have studied the Zn-Sn binary system; however, little data is available in the range below 0.1 mole fraction zinc.5= Previous high-temperature galvanic cell studies in the Sn-Zn-Bi ternary system included the determination by Gluck and Pehlke of interactions in the bismuth-rich corner1 and separate investigations of the central region by Oleari and Fioriani6 and by Ptak and Moser.7 Yokokowa et al.8 conducted Knudsen effusion studies in the central region; however, their experiments at 625°K were conducted somewhat below the present experimental temperature range. Their results indicated an increase in zinc activity with the addition of bismuth. The present series of experiments was conducted in galvanic cells represented as follows: Zn Zn++ in LiCI-KC1 eutectic Zn + Bi in Sn (pure reference (fused salt electrolyte) (molten alloy) standard) The experimental apparatus. a multi-electrode system employing alumina crucibles and contained in a Vycor tube under a helium atmosphere, has been described previously, as have been the experimental procedures, precautions, and the methods of data reduction.1-4,- The experimental measurements were made over the range from 450° to 650°C. Between thirty and forty measurements were made in each run. The linearity of the electromotive force vs temperature relations was verified by linear regression techniques. The correlation coefficients exceeded 0.99. The experimental results summarized in Table I include the interpolated electromotive force at 550°C and the temperature dependence of electromotive force. Only results from stable and consistent cells containing more than 0.025 mole fraction zinc are reported. Attempts to run cells at 0.01 or 0.02 mole fraction zinc were not satisfactory. This is attributed to the closeness of the free energies of formation of the chlorides of tin and zinc. Calculations employing Wagner and Werner&apos;s criteria for displacement reactions10 indicated that reduction of the zinc content to 0.01 mole fraction places the cell near the borderline concentration for a 1 pct error in measured potential. The compositions shown in Table I are the actual weighed-in amounts. Previous experience has indicated that compositional changes during the running of a stable cell are negligible.&apos; Over the range of compositions studied for the binary alloys, the activity coefficient of zinc was essentially constant indicating that Henry&apos;s law is followed to 0.05 mole fraction zinc. The temperature, OK, de-

Jan 1, 1969

THE paper on "Cross-cuts in Coal Mining," by J. J. Rutledge (published in MINING AND METAL-LURGY, February, 1927, p. 64) was brought up for discussion at the annual meeting, where the follow-ing comments were made T. D. Thomas (Lehigh Coal & Navigation Co., Lansford, Pa.) : This question has caused me a lot of worry, not in the particular district in which I am, but throughout other districts. There are always several angles to consider. If you are in a hurry to push development work, you might increase the distance between cross-cuts from 60 to 350 ft., but if you have a 40-ft. chain pillar every 60 ft. it will cut down your entry driving a whole lot. Looking at it from the ventilation angle, I agree that too many cross-cuts in entries are bad things. You have a tremendous amount of leakage, and I have seen currents starting out with 45,000 cu. ft., and after passing about 30 or 40 cross-cuts the current has dwindled down to about 18,000 or 15;000 cu. ft. The result is that the question of putting in auxiliary fans is raised. That involves several points into which I do not want to go too far, but I am in favor of not getting in too many cross-cuts, putting them in only where they are necessary: I think the state mining laws are wrong in a number of places on that, and that when you finish with a cross-cut it should be in the room. It should be well sealed on an entry. There are several ways of tightening up the cross-cuts so as not to have the great amount of leakage and wastage of: air that we now have. &apos;I prefer tile stopping; other people prefer cement or brick, but there is a big fac-tor to all mines, saving the mine. I checked up on the number of fans in the anthracite region and found there are 651. That was derived from the state report of 1921, and it enabled me to compute from the power the weight of the air. In the anthracite region of Pennsylvania we put in 9 tons of air to every ton of coal we get out. Tracing that back again and taking the Government&apos;s figures which they made some time ago, I found but 20 per cent of the air got to the faces where it was actually needed. That is a tremendous big loss and shows a possibility for saving, money for the various coal companies. Chairman Rice: I think what Mr. Thomas refers to was an investigation by R. Y. Williams, of the Bureau of Mines in Illinois, where a study was made of 100 typical mines, and, speaking off-hand, my recollection is that we found as little as 15 per cent of air reached the faces in one of the mines and another was as much as 50. That seems to be a reflection on the type of stoppings and general ventilation scheme.

Jan 3, 1927

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By H. L. Luo

SYSTEMATIC investigations of the Fe-Ga system have been reported only very recently."&apos; The maximum solid solubility of gallium in a-Fe is nearly 50 at. pet at 900°C. However, from Ref. 1, it was not evident that the a-Fe solid solution could be retained successfully beyond 17.38 at. pet Ga by solid-state quenching. The present investigation reports the retention of a-Fe solid solution at 50 at. pet Ga by quenching from the liquid. An ordered phase of CsC1-type B2) structure was observed between 34 - 50 at. pet Ga. Since it was considered very probable that the CsCl structure would occur at high temperatures, alloy filings were also quenched by the conventional quenching technique. In addition to the CsCl phase, a second ordered phase of BiF3-type (DO3) structure was found in the range 25 - 30 at. pet Ga. Alloys were prepared from elements of 99.99 pet purity or better, induction-melted in alumina crucibles under hydrogen. After reweighing, the alloy ingots were cast into wires under argon. From the weight losses and the reproducibility of the lattice parameters, compositions were estimated to be within ± 0.3 at. pet. The techniques of quenching from the liquid state were reported before.3-5 Prior to quenching, a small section of cast alloy wire (30 - 50 mg) was melted in an alumina insert under an argon flow. The quenched specimens were in the form of flakes, typically 1 sq mm in area. For solid-state quenching, alloy filings passing 200 mesh were sealed under a reduced helium atmosphere in a thin-bottom silica tube. After heating for -30 min at the desired temperature in a vertical furnace, the sealed tube was rapidly dropped into ice water so that the thin bottom of the tube broke on impact. The quenched alloy filings were always ferromagnetic and could be collected by a magnet. X-ray diffraction patterns were taken with iron-filtered cobalt radiation in a 114.6-mm-diam Debye-Scherrer camera. High-angle lines were always resolved and spacings were computed relative to ? (CoKa1) = 1.78890Å. Lattice parameters were obtained from extrapolation against the Nelson-Riley function. The variation of lattice parameter with composition is shown in Fig. 1, together with the data of Dasarathy and Hume-Rothery.1 Uncertainties in the present measurements are within the dimensions of the symbols or indicated by error bars. X-ray diffraction lines indicative of CsC1-type ordering could be clearly identified for alloys of 34 - 50 at. pet Ga quenched from the liquid and alloys of 35 - 41 at. pet Ga quenched from -975°C. Within experimental error, no difference in

Jan 1, 1968

By Nev A. Gokcen

PUBLISHED data on the solubility of nitrogen in liquid manganese are widely discordant. Ochsenfeldl observed that a Mn-N alloy with 3.6 pct N consisted of solid and liquid phases at 1260°C but at 13 00° to 1340°C the solid phase disappeared and the liquid contained 0.1 to 0.13 pct N. In contrast Saito&apos;s measurements at approxhately 1400°C yielded an average value of 0.97 pct N. Sieverts3 volumetric method is not suitable for the determination of gas solubility in manganese because the liquid metal vaporizes readily and condenses in the cooler parts of the apparatus where it can absorb large amounts of nitrogen. The purpose of this investigation was, therefore, to determine the solubility of nitrogen in manganese accurately in the range of 1273" to 1500°C. The experimental method used in this study was as follows. Electrolytic manganese of 99.9 pct purity, and weighing 50 g, was melted in a pure alumina crucible placed in a tubular furnace. Temperature was measured with a Pt-10 pct Rh thermocouple and controlled within ± 5°C. Pure nitrogen was bubbled through the melt for 1 hr at constant temperature and then a sample was taken by sucking the metal into a 2-mm clear silica tube and immediately quenching in water. The sample was broken into small pieces and found to be sound to the naked eye. The entire sample was then dissolved and the resulting solution was analyzed for nitrogen by the well-known solution-distillation method. The experimental results are presented in Fig. 1. All the nitrogen solubility data refer to 1 atm of nitrogen pressure; hence the observed values are slightly corrected by using Sieverts&apos; equation when the atmospheric pressure differed more than 5 mm Hg from 760 mm, and further, in the case of the runs at 1500°C the correction arising from the presence of Mn vapor has been made. (Cf. Eq. [3]). Scattering in the data is within ±5°C in temperature measurement and ±3 pct in total nitrogen analysis. The straight line in Fig. 1, correlating the percentage of dissolved nitrogen, %N, with the inverse temperature in OK-1, can be expressed by:

Jan 1, 1962

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor&apos;s degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre&apos;s program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre&apos;s schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By M. Herman, G. J. London

A series of dilute Fe-Co alloy specimens were prepared from zone-melted iron. The iron used was given ten floating-zone passes in purified hydrogen. Alloying was accomplished by plating a gradient of metallic cobalt onto a 1/4-in.-diam bar of material from a pure plating bath. The deposit was radioac-tively tagged by a small addition of co80 to the plating bath. Alloy homogenization was accomplished by passing an additional floating-zone pass through the plated section of the bar. The final concentration gradient achieved was from residual to about 1000 ppm (0.1 pct) added Co. After homogenization, the bar was swaged to 0.057 in. wire and cut to tensile specimen blanks 1-1/16 in. long. Each specimen was counted in a well-type scintillation counter. The concentration of cobalt was computed by combining the normalized specimen counting rate with the known weight (measured to the nearest 0.01 mg) of cobalt added during plating. Fig. 1 shows the cobalt gradient obtained, exclusive of residual cobalt which was estimated by neutron-activation analysis to be approximately 50 ppm. Results of recrystallization for 1 hr at 750°, 700°, 650°, and 600°C with specimens containing 40, 170, 470, and 870 ppm added Co are shown in Figs. 2, 3, 4, and 5. Recrystallization was accomplished in a dynamic vacuum of less than 1 x 10 torr. The specimens were mounted and polished parallel to the swaging direction. The recrystallization re- sults show a radical coarsening of structure with increasing cobalt concentration. The coarsest structure obtained was at the 470-ppm level (at all recrystallization temperatures) with a slight grain refinement at the 870-ppm level shown. A more normal solid-solution effect is seen in Fig. 5 (60OoC, 1 hr) where the only specimen completely recrystallized is the one containing 47 ppm Co. Since the possibility existed that some atmosphere-contamination phenomenon might be responsible for the observed results the recrystallization series was repeated using sealed quartz capsules. These were filled with purified argon which was gettered during heat treatment on metallic titanium included in the capsules. The results obtained were essentially the same as shown. Another identical alloy was made using a 5-mm-diam bar of Westinghouse Puron. Specimen preparation and recrystallization treatment were also as described. The results obtained (see Table I) were somewhat erratic. Some coarsening in structure does appear at the highest cobalt concentrations. There is no apparent relationship between the coarse, columnar, directionally solidified structure of the as-melted bars and any of the recrystallized grain structures observed, all of which are much finer than the former structure. A recrystallization process can be most simply described as one of homogeneous nucleation of recrystallized grains in a cold-worked matrix followed by more or less uniform growth of the strain free grain into the cold-worked material.&apos; An impurity element may influence one or both of these processes. Aust and utter&apos; have shown that impurities strongly influence grain boundary mobility in lead. Moreover, definite recrystallization textures are produced by small concentrations of tin,3 while additions of silver or gold4 produce large boundary in-

Jan 1, 1964

By R. R. Boucher, O. J. C. Runnalls

A pronounced thermal effect has been observed on heating or cooling a1wninum-rich Al-U and Al-Pu alloys. From microscopic and X-ray diffractionstudies, the effectl has been attributed to trnsfor)nations in the inlemetallic phases UAl, and PuAl , involuing rearrangement or cluslering of vacancies The transformation obsrved in Al-20 wi oct U alloys occurred near the a Al-UAl4 eutectic tem-perature of 646°C making it difjicult to detect from heating curves. When cooling, howeoer, thermal mad X-ray analyses indicnted that the high-temperati~re phase labeled p UAL, precipitated initially during euitectic solidification. As solidification continued and after an induction period o-f 5 lo 20 tnin the nu-cleatiorz and growth of the low- twmperature phase, a UAl4 produced an euolution of energy which raised the observed alloy temperature by 1° to 2°C. in Al-Pu alloys the transformation occurred at 645°C, 5 deg below the eutectic solidification temperccture. The eslimated latent heat of transformation was 25 +5 cnl per g PuAl,. The high-tetnpevcl-ture forms of UAl, and PuAl, were easily 9-etccined by chill casting Al-U and Al-Pu alloys and on reheating the alloys the trcltzsforrnation to the a phase was sluggish even above 600°C. Separated single cryslals o-f UAl4, joy example, showed no evidence Of transformalion after heating for 16 hr at 620°C. The transformation rates increased yapidly enough with increasing temperature, however, that a a spontaneous liberation of energy lens observed on occasion when bealing cast Al-20 wt pet U to neal- the RECENT phase studies on A1-Pu alloys have indicated that earlier reported equilibrium diagrams should be modified to take account of several poly- morphic transformations in the intermetallic compound PuAl,.&apos; During the course of the latter work an unexpected heat evolution was observed while cooling a solid alloy consisting of a mixture of a aluminum and PuA1,. The evolution occurred at 645°C, y below the a A1-Pu A1, eutectic solidification temperature. Subsequent thermal-analysis experiments with A1-U alloys showed that heat was evolved there also at a temperature nearly coincident with the a A1-UA1, eutectic solidification temperature of 646°. A search of the literature revealed that similar thermal effects had been observed before for both A1-U and A1-Pu but had never been fully explained.2,3 The purpose of the present paper is to describe thermal-analysis and X-ray diffraction experiments which have led to the conclusion that the thermal effects are due to transformations which involve the rearrangement of vacancies in the intermetallic compounds UA1, and PuA1,. EXPERIMENTAL PROCEDURE The A1-U alloys were prepared by heating super-pure aluminum (99.99 pct +) obtained from the Aluminum Co. of Canada in a graphite crucible surrounded by an induction coil. At 1000°C high-purity uranium metal produced by the Eldorado Mining and Refining Co., Ltd. was dropped into the liquid aluminum and was dissolved completely within 15 min. The impurities in the uranium were A1—4 ppm, Ca-4, C-70, Cr-3, Cu-6, Fe-30, Mg-2, Mn-10, Ni-25, Si-25, and Zn-2. The A1-Pu alloys were prepared by reacting plutonium dioxide with liquid aluminum under cryolite (3 NaF . AlF,) for 10 min at 1100°C in graphite crucibles exposed to the air. The plutonium was 99.8 pct pure, containing trace impurities of Ca, Cu, Fe, Pb, Si, and Zn. The liquid alloys were usually poured into water-cooled molds to provide castings of uniform composition from which samples could be cut for heat treatment and thermal-analysis experiments.

Jan 1, 1965

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.&apos; In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat&apos;s values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By R. E. Pray, M. C. Fuerstenau, J. D. Miller, B. F. Perinne

Quartz cannot be floated with potassium amyl xanthate as collector at any pH. Complete flotation is achieved with certain minimal additions of amyl xanthate and Pb from pH 5.8 to 8.5 and with amyl xanthate and Zn from pH 7.5 to 8.1. The active species of these metal ions responsible for activation are shown to be PbOH and ZnOH No flotation was effected when Cu and Mg were added as activators. Previous work1,2,3,4,5,6,7 has shown that quartz may be floated in the presence of sulfonate or soap when the following two criteria are met: 1) some portion of the added metal ion has hydro-lyzed to its first hydroxy complex, and 2) a precipitate of the metal-collector has formed. Since sulfonate and soap, two substantially different anionic collectors, conform to these criteria, this phenomenon may well be expected to be of a general nature. In this view then, it would appear that any anionic collector, including xanthates, should also float quartz when these two criteria are met. The object of this paper is to demonstrate the conditions under which quartz will respond to flotation in the presence of potassium amyl xanthate. EXPERIMENTAL MATERIALS AND TECHNIQUES Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Potassium amyl xanthate was selected as collector. Purification of this reagent was effected with the following method: 1) a laboratory sample of potassium amyl xanthate was dissolved to saturation in hot ethyl alcohol and filtered several times while still hot, 2) the filtrate was cooled, during which time potassium amyl xanthate crystallized out of solution; the xanthate was then separated from the solution by filtration, 3) the amyl xanthate was dissolved in fresh hot ethyl alcohol and filtered, 4) step (2) was repeated, 5) the crystalline potassium amyl xanthate was washed with ethyl ether five times, and 6) the xanthate was dried for 24 hours under continuous vacuum. Inorganic impurities are insoluble in hot ethyl alcohol whereas dixanthogen is soluble in ethyl ether. Five-gram charges of 48x150 mesh quartz were conditioned for 3 min in 125 cc of solution containing the reagents and were floated with the small-scale cell and procedure described in previous papers.478 Reagent grade HCl and NaOH were used for pH adjustment, while reagent n-amyl alcohol was added as frother. Frother addition is necessary with this technique, but it should be mentioned that data, similar to those shown in Fig. 2 for 1 x10-4 mole per liter Pb++ and 1 X 10-4 mole per liter AX-, were also obtained with a Hallimond cell in the absence of frother. EXPERIMENTAL RESULTS Clean quartz could not be floated with amyl xanthate at any pH. Flotation was achieved under certain conditions, however, when various metal ions were added to the system. The activating ions used were lead, zinc, copper and magnesium, added as reagent grade chloride salts. Lead as Activator: The effect of Pb++ as activator was examined at five different additions of amyl xanthate (Fig. 1, 2 and 3). When 1x 10-5 mole per liter xanthate was added in the presence of 1 x 10"4 mole per liter Pb ++, no flotation was obtained at pH 6.5 or below, while a recovery of about 60% was effected at pH 7. When the pH was increased to 7.8, no flotation was again obtained, Complete depression was noted from pH 7.8 to about 10, at which point a recovery of about 30% was achieved. At about pH 11, the precipitate of lead amyl xanthate which was present below this pH dissolved and complete depression occurred. When 2.5x 10-5 mole per liter xanthate was added with the same lead addition, no flotation was obtained at pH 5.8 and below, whereas a recovery of

Jan 1, 1965

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller&apos;s earths fall within the general group of bleaching clays and gradually the commercial term "fuller&apos;s earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller&apos;s Mud Clay (Wyoming) Earth (P Peak)&apos; (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By Milton E. Wadsworth, J. Brent Hiskey

INTRODUCTION Fifteen years ago a distinguished electrochemist referred to electrochemistry as an "underdeveloped science " In the article in question, Professor Bockris (1) stated that many areas of.natura1 phenomena and applied technology are not perceived as being electrochemically based At that time, this was especially true for much of non-ferrous extractive metallurgy and was a particularly accurate description of hydrometallurgy During the last decade, there has been considerable advancement in applying the theory of electrochemistry to our know1 edge of hydrometallurgical processes and in understanding the mechanisms of underlying electrode reactions. Impressive as these advances are, there is still a growing need for electrochemical research of mineral systems and electrochemical engineering to apply this work in practical situations In a broad sense electrochemistry is defined as the physical chemistry of ions in solution and of phenomena which occur at the electrified interface. Bockris and Reddy (2) refer to electrochemistry as being divided into two fundamental domains, ionics and electrodics ionics is restricted to the behavior of ions in solutions, examples being many familiar redox processes Electrodics represents the main part of electrochemistry, and is the study of charged interfaces and the conditions governing charge transfer reactions across them. Considering hydrometallurgical applications, electrodics suggests the following relationship for a conducting solid (bulk or surface)

Jan 1, 1981

By D. G. Westlake

Polycrystalline tensile specimens of various Zr-0-H alloys have been tested at 298°, 178°, and 77°K. Solute oxygen and hydride precipitates in quenched alloys made individual contributions to the yield strength at 0.2 pct strain which combined to produce a resultant strength increment, a,., Ductility changes which were ohserved can he interpreted in terms of the various oxygen and hydrogen concentrations, testing tem -peratures, and dispositions of the hydride. ADDITIONS of oxygen in solid solution were known to increase the yield and tensile strengths of polycrystalline zirconium as early as 1951.&apos; More recently, the critical resolved shear stress (CRSS) for prism slip in zirconium single crystals was also shown to be affected by the solute oxygen impurity.&apos; This latter work also demonstrated that large increments of strength could be contributed by the finely dispersed zirconium hydride precipitates that are present in quenched Zr-H alloys.3 It was concluded that the combined strengthening due to alloying could be expressed by where to is the increase in the CRSS due to solute oxygen alone and TH is the increase due to finely dispersed hydride precipitates. Eq. [I] is analogous to one used to express the combined strengthening effects of work hardening and neutron radiation damage.4 Eq. [1] was verified only indirectly and for only small amounts of the impurities—up to 0.14 at. pct 0 and 0.63 at. pct H. The present investigation was undertaken to obtain a more direct verification of the validity of the form of Eq. [1] for this system and also to determine the combined effects of oxygen and finely dispersed hydride precipitates on the tensile strength and ductility of polycrystalline zirconium. EXPERIMENTAL PROCEDURE Tensile specimens were machined from the same rolled billet of Kroll zirconium used in the earlier study.&apos; These measured 38 by 4.7 by 0.5 mm and had 10-mm gage lengths which were 2.8 by 0.5 mm. Each specimen was ß-annealed in vacuo at 1173°K for 15.5 hr and a-annealed at 1073°K for 4 hr to D. G. WESTLAKE, Member AIME, is Associate Metal l ur-gist, Metallurgy Division, Argonne National Laboratory, Argonne, III. Manuscript submitted July 17, 1964. IMD______________ give an equiaxed structure with grain diameters averaging 0.06 mm. Oxygen was added by allowing the metal to react with a known quantity of oxygen during the 0 anneal and known quantities of hydrogen were added during the a anneal. Each alloy was encapsulated in Pyrex under vacuum, annealed at 873°K for 4 hr, quenched into ice water, and polished by immersion in a solution of 46.75 vol pct H2O, 46.75 vol pct concentrated HNO3, and 6.5 vol pct HF (49 pct) at 298°K. Special heat treatments given to a few specimens are described in the results below. Tensile tests were done on an Instron machine and were begun within 20 min after the quench, except where specified otherwise. Tests at 298°K were in air, at 178°K in acetone, and at 77°K in liquid nitrogen. All tests were at a strain rate of 8x sec-1. RESULTS AND DISCUSSION Yield Stress at 298°K. The compositions of alloys and the corresponding yield stresses (0.2 pct strain) are given in Table I. A plot of the yield stresses of the oxygen alloys, A, B, C, and D, indicates that varies linearly with CO1/2, where Co is the oxygen concentration, Fig. 1. This is in accord with Fleischer&apos;s6 theory for solution strengthening if the oxygen atoms do not cluster, or the cluster size remains constant with increasing oxygen concentration. In Fig. 1, it appears that if one could prepare some oxygen-free zirconium its yield stress would be very low. Therefore, we shall assume that for the oxygen alloys is equivalent to O0, the strength increment contributed by the presence of oxygen. The relationship between0.2and Co is expressed by 0.2 = 31.3 CO1/2, when the yield stress is in kg per sq mm and the concentration is in at. pct. Each of the hydrogen alloys, Al, A2, A3, and A4, contained 0.081 at. pct 0 as an impurity. In Fig. 1, it appears that this small amount of oxygen makes a significant contribution to the strength which cannot be ignored when we evaluate the contribution of the finely dispersed hydride. Let us assume the validity of the following equation: a0.2 = (a2o+a2R)1/2 [2] which is analogous to Eq. [I] for single crystals, and calculate values of UH for the hydrogen alloys by using the experimental values of 0.2 and o (0.081 at. pct) = 8.9 kg per sq mm. For 0.36 at. pct H, oH = 6.47; for 0.72 at. pct H, OH = 11.30; for 2.16 at. pct H, OH = 19.4; and for 3.60 at. pct H,

Jan 1, 1965