Search Documents

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

By J. Weertman

The paper of Gifkins and Snowden considers the interesting but difficult problem of determining the stress dependence of secondary (steady-state) creep at low stresses. These authors have concluded that at stresses below 250 psi (2 x 107 dynes per sq cm) the secondary creep rate of lead is proportional to the stress (viscous creep) and is not proportional to the stress raised to about a fifth power. The experimental data considered by them were obtained on tests conducted at room temperature and at 50°C. The lowest stress employed was 50 psi (3.5 X 106 dynes per sq cm). The authors pointed out the main difficulty in determining the stress dependence of creep at low stresses. The creep tests must be run for very long lengths of time. However they made no estimates of when an experimental creep rate determination must be rejected because it does not represent a true steady-state or minimum creep rate. In order to be certain that a creep curve is within the steady-state region, the total creep strain should be of the order of 0.1 to 0.2. For a creep test of a year's duration this requirement implies that a secondary creep rate smaller than about 10-3 per hr cannot be measured reliably. The corresponding creep rate for a 10-year test is 10-6 per hr. The creep rates of the tests that were considered by the authors to prove the existence of viscous creep were of the order of or less than 10-6 per hr. One can conclude reasonably that this data does not prove unambiguously that large strain steady-state creep rate of lead is proportional to the stress in the stress range of 50 to 250 psi (3.5 x 106 to 2 X 107 dynes per sq cm). Another technique can be used to obtain the stress dependence at low stress levels. The creep rate is a very sensitive function of temperature. The creep rate can be increased by very large amounts merely by increasing the temperature. We carried out steady-state creep tests on lead single crystals25 at temperatures up to 320°C. We were able to obtain creep rate data down to stresses as low as 35 psi (2.5 x 10' dynes per sq cm). Our smallest creep rate was 8 x 10-5 per hr. Thus we obtained large strain, steady-state creep rates to even lower stresses than were considered by Gifkins and Snowden. No evidence was seen for viscous creep. The creep rate was proportional to the stress raised to about a 4.5 power down to the lowest stresses. Since there is no reason to believe that changing the temperature should change the stress dependence of steady-state creep, we feel that large strain viscous creep does not occur in the stress range quoted by the authors for lead single crystals or large-grain polycrystalline samples of lead. This conclusion does not imply that viscous creep may nat occur in a lower stress range or in the same stress range for fine grain material or at creep strains very much smaller than 0.1. Support by the U.S. Office of Naval Research is acknowledged. Authors' Reply R. C. Gifkins and K. U. Snowden We thank Dr. Weertman for his discussion and although, as we hope to show, we do not agree with his reservations, we do concur in stressing the importance of ensuring that creep rates are reliably obtained. Dr. Weertman appears to be content to accept n = 1 for low stresses with fine-grained material but not for single crystals. We believe our results show that the former result cannot be accepted without also accepting the latter. We will also show that the probable errors in our minimum creep rates are insufficient to alter our conclusions, that the criterion proposed by Dr. Weertman is arbitrarily restrictive and his alternative experimental approach possibly invalid. 1) A principal result of our Fig. 1(a) is that n = 1 for polycrystalline specimens at room temperature and 50°C for stresses below -250 psi. There was evidence that crystal slip and grain boundary sliding contributed approximately equaily to the overall strain in this low-stress regime. This implies that either a) grain boundary sliding controls slip within the grains or b) both grain boundary sliding and crystal slip independently occur according to mechanisms which give n = 1. Alternative a does not seem acceptable, so we were forced to consider b. This led us to reexamine work on bicrystals by Strutt and Gifkins and plot curves Fig. l(b). Previously Strutt et al. (loc. cit.), had merged these points with others using the Zener-Holloman parameter and thus, we now believe, had been led to overlook the behavior where n = 1. Curves C and D in Fig. l(b) did appear to confirm the hypotheses that n = 1 for crystal slip at these low stresses and the sliding curve F was similarly of the expected form. It was comparatively easy to find a quantitative theory to account for n = 1 for sliding and the similarity of curves C and D to curve F (all obtained from the same set of specimens) led us to feel that the single-crystal curves were valid. 2) We believe the secondary creep rates for both the polycrystalline and single-crystal specimens to be in error by factors c2. In Fig. 6 creep curves for polycrystalline specimens of lead(1) and lead(II) are reproduced as curves a and b, respectively, and curve c is for a single crystal at 100 psi. It is clear that, although the attainment of secondary creep rate takes 2 years for a and 150 days for b, thereafter the curve is linear for periods of 7 and -1 year, respectively. The single crystal has a linear portion commencing after 20 and extending to 90 days. Creep extension was measured directly using a traveling microscope reading to 0.01 mm on gage lengths marked on the specimens; the gage lengths

Jan 1, 1968

By R. E. Ogilvie, E. T. Peters

The X-ray Kossel-line method has been used preaioz~sly for measuring lattice parameters to accuracies of 1 part in 100,000.5 A second application of this method is described for determining the crystallographic orientation of a randomly positioned single-crysta1 spherical volume that can he as small as 50 µ in diameter, within accuracy limits of ±1/2 deg. The theory, experimental procedure, and interpretation of Kossel-line patterns and an experimenta1 verification of the predicted orientation relationship of the cph k and fee a Cu-Si phases are presented. This orientation relationship can be described as (111)a, (00.1)k; [110]a [11.0]k. In addition, the lattice parameter of the a phase was found to he a. = 3.62154 ± 0.00014Å. The Kossel-line method when used in conjunction with electron microanalysis is shown to he capable of providing a complete chemical and structural analysis of a given crystal. THE most easily accomplished methods for determining the orientation of a single crystal are variations of the Laue X-ray diffraction method. Although certain materials can be oriented to within ± 1 deg accuracy by observation of exterior macroscopic features, such as etch pits, cleavage faces, or growth features, the Laue method is generally preferred for routine laboratory application. Both back-reflection and transmission patterns are coordinated by appropriate reference charts and are plotted in terms of reflection plane poles (normals) on a stereographic projection. Orientation is deduced by relating the pole distribution (which is fixed by the crystallographic symmetry of the specimen) to two specified external reference directions. The Laue method has several limitations. 1) Orientation can rarely be determined to better than ±l deg accuracy. Principal errors involve inaccuracy in specimen-to-film distance, measurement confidence of individual Laue spots, and stereographic plotting. 2) Because of the indeterminacy of the X-ray wave length diffracted to a given spot, it is not possible to determine supplementary crystallographic data, such as interplanar spacings and lattice parameters. 3) The method is generally limited to specimens of cubic symmetry or to specimens of high symmetry and known structure. 4) The relatively large cross-sectional area of the incident X-ray beam generally precludes the measurement of relative grain orientation in a polycrystalline material.* _____ Several of these limitations can be overcome by application of the Kossel-line method, which has been previously employed for precision lattice-parameter determinations.'-= For this method, a point source of divergent monochromatic X-rays is generated within the crystal by means of an incident electron beam. The divergent X-rays which fulfill the Bragg law are diffracted by the specimen and are recorded on a film placed either in transmission or back reflection. Analysis of the film yields a direct measurement of orientation and lattice-spacing values to an accuracy of ±1/2 pct. As analyses can be obtained from spherical specimen volumes as small as 50 µ in diameter, the method provides a means for structural analysis of second-phase or impurity precipitates within a given matrix. The primary limitation of the Kossel-line method is the requirement for an electron microanalyzer or similar apparatus capable of producing a finely focused electron beam. This paper is designed to present the theory, experimental procedure, and geometrical interpretation of Kossel patterns. The experimentally determined orientation relationship between the k and a phases occurring in the Cu-Si system and a precision measurement of the a lattice parameter are presented as a practical application of the method. THEORY OF KOSSEL LINES Divergent X-ray beam photography utilizes an effective point source of characteristic X-rays which, when diffracted from a single crystal, form numerous diffraction and absorption cones that are recorded on film.7 The cones generated from a source lying within the crystal are called Kossel lines.' Although the X-ray scattering from a divergent point source contained within a crystal is described in terms of Laue dynamical theory,9 the directions of the diffracted spectra can be ade-

Jan 1, 1965

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors' results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. ' The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

By A. J. Goss, M. Tanenbaum, W. G. Pfann

THE purification of two metals, antimony and tin, by zone refining is described, and a reciprocating method of passing molten zones through a straight ingot, which effects a considerable economy of time and apparatus, is discussed. Antimony has been used extensively as a doping agent in germanium and silicon. More recently, it has become important in the preparation of new semiconducting compounds such as InSb, GaSb, and AlSb. High purity is especially necessary in this latter use, since the antimony may comprise as much as 80 pct by weight of the compound. Antimony is generally available in a commercial form of about 99.8 pct purity. Column 1 of Table I is a typical emission spectra analysis of commercially available 99.8 pct antimony. Zone refining has been quite successful in increasing the purity of such samples. Columns 2 to 4 of Table I are analyses of an ingot of the antimony of column 1 after the passage of seven molten zones in an atmosphere of nitrogen. The ingot length was 9 1/2 in.; the mean zone length was 2 in.; convection was the only means of stirring. The column headings are sample locations in inches from the leading end of the ingot. The results illustrate both the merit and a limitation of zone refining. It is seen that four of the five impurities—nickel, arsenic, lead,

Jan 1, 1955

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.' Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800' to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963

By J. Szekely

A rrlethod is presented for the estitnation of oxygen pickup by teettzed molten steel streams. Of the mechanisrt~s considered for oxygen absorption, physical entrainment appeared to be the most significant. The estent of this physical entrainment may be calculated by the application of boundary layer theory. It was found that the values of oxygen pickup thus predicted were in wry good agreement with data reported in the literature, in the case of short, well-defined metal streams. This entrainment model does not provide an adequate description of oxygen pickup by long streams, exoosed to external winds and where breakup of the streatn is likely. WheN molten steel is teemed into a mold or tundish it will absorb oxygen contained in its environment. Recently interest has been expressed in the measurement and possible prediction of the extent of this oxygen absorption: this interest owes its existence to two principal factors: a) the desirability of providing a quantitative assessment of the role played by the absorbed oxygen in impairing the quality of (vacuum degassed. stainless, or continuously cast) steel; b) the need for providing guidelines for stream protection methods. The purpose of this communication is to suggest a simple method for the prediction of oxygen absorption by continuous metal streams and to compare the predicted values with the data available in the literature. It is hoped that this method may provide at least an initial framework for the interpretation of additional data that might become available. FORMULATION Consider a continuous metal stream falling into a molten metal pool as depicted in Fig. 1. This system may absorb oxygen due to the following two mechanisms: 1) physical entrainment of gases (including oxygen) into the molten pool where reactions. thus absorption, will occur; 2) mass transfer (convec:tive diffusion) of oxygen to the metal stream. 1) Physical Entrainment. The physical entrainment may be calculated by using the concept of the diaplace-ttzent tlzickness of the laminar boundary layer, which will be stated briefly in the following.&apos; When a fluid flows past a solid surface, a portion of the fluid close to the surface is retarded due to fric-tional forces. This region in which the velocity of the fluid differs from that in the main stream is called the boundary layer. An illustration of this is given in Fig. 2 where it is seen that the thickness of the boundary layer increases as we move along in the x direction. In the laminar region, when Re, < 10&apos; the thickness of the boundary layer is given by the following relationship: f =4.64 Re;1" [1] where 61 is the boundary layer thickness, x is the length along the leading edge, Us is the velocity of the free stream, (i is the viscosity of the fluid (gas in this instance).

Jan 1, 1970

By L. F. Mondolfo, W. T. Collins

A study of the relationship between undercooling for nucleation and structure in Sn-Cu alloys with 0.1 to 5 pct Cu has shown that in hypereutectic allojls the halo of tin that surrounds the primary crystals of Cu3Sn5 is larger, the larger the undercooling for nucleation o,f the tin. This increase of halo size results in a decrease of coupled eutectic, and, in alloys far from the eulectic composition, may produce its complete disappeavance, with the formation of a divorced eutectic structure. This was confirnred by the excrrnination of other alloys in which divorced eutectic slructuves are formed, and leads to the conclusion that they ave only an extrenle case of halo forrtzalion , which results when the two phases freeze one at a time and solidification of the first is completed Defove the second starts. It was also found that under proper conditions of nucleation all types of eutectic structures can be formed in the sartte system , and therefore divorced eutectics, like normal and anomalous, are not characteristic of the syslett~, but are mainly controlled by nucleatiorz. Dizlovced eutectics are formed when the phase that tutcleates the eulectic vequires a large undevcooling for ils nucleation and when the cotnpositiorz of the alloy is far from the eutectic., on the side of the primary phase that does not nucleate the other phase. It is recommended that the tevm "divorced" be used in preference to degenerate because it is more desct-iptice of the morphology and mode of forinalion of the structures. ThE variety of structures found in eutectic alloys has been extensively investigated and classified. The most accepted classification is the one by ~cheil,&apos; in which three different types of eutectic were distinguished: 1) normal, 2) anomalous, 3) degenerate (divorced). ATornlal eutectics are typified by the simultaneous growth of the two phases ("coupling") by which the two phases appear as interpenetrating crystals. The presence of a crystallization front, in which the two phases grow side by side, creates the eutectic grains, with the boundaries where the fronts meet. The presence of eutectic grains is the .distinguishing feature of a normal eutectic, according to Scheil. Straumanis and Brakss2 examined the Cd-Zn system and showed that there was a crystallographic relationship between the phases. Later, others4 also investigated additional systems and found definite crystallographic relationships in the coupled eutectics. The anornalous eutectic shows much less coupling than the normal; the two phases are intimately mixed but &apos;grow without a uniform crystallization front—a consistent crystallographic relationship— and the eutectic grain is conspicuously absent. As in the normal eutectics faster rates of growth result in a finer structure, but there is not the typical uniform spacing of normal eutectics. The degenerate eutectic shows no coupling; in fact the two phases attempt to minimize their area of contact and to form separate crystals. It has been suggested5" that slow cooling may favor this type of structure. Scheil believes that normal eutectics are formed when the two solid phases are present in more or less equal proportions, whereas both anomalous and degenerate eutectics form when one of the phases is present only in small amounts. spengler7 extended much farther this qualitative relationship between the eutectic type and the ratio of the two phases, and added a relationship to the melting point of the constituents. On this basis he proposed two equations for determining into which of Scheil&apos;s classifications an alloy belongs. The first equation is: where TI is the melting temperature of the lower-melting component, Tp of the higher-melting component, and Te the eutectic temperature. The second equations is: where is the volume percent of the lower-melting phase and $2 of the higher-melting phase at the eutectic composition. If 0 and/or 4 are in the range 0.1 to 1, a normal eutectic is formed; if in the range 0.01 to 0.1, anomalous; if less than 0.01, degenerate. Although the examples given by Spengler show a good agreement with the formulas, chadwick found that the Zn-Sn eutectic is normal to all growth rates, even though the volume ratio is 12/1, and Davies9 reports that the A1-AlgCo2 eutectic is normal, with a volume ratio of more than 30/1. Many more discrepancies of this type can also be found. Neither Scheil nor most of the other investigators have considered nucleation as a factor in the formation of divorced eutectics. Daviesg states that divorced eutectics form when neither phase acts as

Jan 1, 1965

By David Mitchell

THE production of fluorspar is one of the smaller nonmetallic indus-tries in the United, States with a capital investment-about $10,000,000. Shipments from United States mines1 in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world&apos;s fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications: Consump- Specifications, Per Cent Use Form tion in 1936, Per Cent CaF2 SiO2 Fe2O3 Metallurgical Gravel 79 +85 -5 or lump Ceramic.. Ground 10 +95 -3 -0.1 Acid Ground 11 +98 -1 The concentration of the coarser sizes presents relatively little diffi-culty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938

By F. Weinberg

WHEN impure Zn (< 99.99 pct)&apos;&apos;Z or Zn-Cd alloys3 are progressively solidified, a cell or "corrugation" substructure4 is produced in the solid, with a high impurity or solute concentration along the cell walls. When these materials are polished and suitably etched, etch pits are often observed along the cell walls. For the Zn-Cd alloys these etch pits have been associated with decorated dislocations, present in the corrugation boundaries to accommodate the lattice strain. In the course of an investigation of Zn-2 pct Au alloy, molten metal of this alloy was poured into cold water and the resultant solid pieces were sectioned, polished and etched with a Cr0 ethant. An extremely regular cell pattern was observed on the etched surface, similar in general to the corrugation structure previously reported for impure zinc and Zn-Cd alloys. At higher magnification, regularly spaced pits were observed along the cell boundaries. An example of the regular cell pattern at the center of a specimen is shown in the center and lower portions of Fig. 1; the top of the figure shows the pattern near the specimen surface. Typical etch pits in the cell walls are shown in Fig. 2. It was surprising that a cell pattern as regular as that shown in the center of Fig. 1 was produced at the very rapid solidification rates used (estimated as > 1 cm per sec). In addition, the distribution coefficient for the Zn-Au system is greater than 1. Accordingly, the center of the cells should be rich in solute and should etch

Jan 1, 1963

By J. H. Scaff, W. G. Pfann

The effects of impurities on the electrical properties of silicon are discussed in a companion paper by Messrs. Scaff, Theuerer, and Schumacher.&apos; It was shown that an ingot of silicon which contained boron and phosphorus in certain concentrations consisted partly of p-silicon and partly of n-silicon2 and that the common boundary between these regions was the source of a photo-voltage. These features were ascribed to the segregation of boron and phosphorus during solidification of the ingot. Because of different rates of segregation the first portion of the ingot to freeze contained a molar excess of boron over phosphorus and hence was p-silicon. The last-solidified region contained a molar excess of phosphorus and was n-silicon. This paper is concerned with the microscopic examination of such ingots. The microstructures are rather unusual in certain respects and their study has helped to show how the segregation of minor elements modifies the electrical properties of silicon. The microstructures of ingots prepared from two lots of silicon, designated 1 and 2, will be described. These lots were obtained from the Electro Metallurgical Co. Both contain 99.8+ pct silicon, but they differ in impurity analysis. For each lot will be shown the microstruc-ture of a slowly cooled ingot, for which the time of solidification is 6 min., and that of a rapidly cooled ingot, for which the time of solidification is 2 min. The ingots were prepared from 45 g charges of silicon. When an alloy freezes a cored structure is generally produced because of insufficient diffusion to remove concentration differences established during freezing. As a result of coring the first portion of a crystal to freeze is usually poorer in solute than equilibrium requires, while the last material to solidify is richer. In a columnar grain, growth is principally unidirectional and coring can produce a concentration gradient along the entire grain. By carrying the picture of the coring process from a single grain to an entire ingot in which columnar grains are aligned more or less radially, one can easily see that a composition gradient could be established between the outside and center of the ingot. This, to a considerable extent, occurs during the solidification of a slowly cooled ingot of silicon. Slowly Cooled Ingot In slowly cooled ingots of both lots of silicon, columnar grains which are approximately radial in direction and longest at the top of the ingot enclose a region in which the shapes and align- ment of the grains are considerably less regular. The central region is last to solidify and contains cavities and inclusions. The sketch of Fig 1 illustrates some of these features, as well as others which will be described below. If a polished section of an ingot is etched in a mixture of 2 parts of 20 pct HF and 98 parts of HNO3 the p-n barrier becomes visible. The overall shape of the barrier in a slowly-cooled ingot is roughly oval, as may be seen in Fig 1. The proportion of n-silicon, that is, the region enclosed by the barrier, is considerably greater in ingots of lot 1 than in those of lot 2. A sample about 34 x 1/8 X 1/8 in. was cut from a slowly cooled ingot of lot 1 with its long direction extending from the top of the ingot to the porous region. Thus its upper half was psilicon, its lower half n-silicon. A longitudinal face was polished and etched in the acid mixture. The areas of interest are identified in Fig 2. A band of parallel markings extends across the sample in the columnar region. These striae are roughly parallel to the upper surface of the ingot and cross grain boundaries with only slight deviations. They are quite distinct in the n-silicon,

Jan 1, 1950

US 4,141,854-Method of resolving water-in-oil emulsions from the organic solvent extraction of uranium from an aqueous ore leach solution The emulsion is treated at optimum temperature with a water-soluble acrylamide copolymer which contains 5-50% by weight of a lower alkyl substituted tertiary aminoethyl methacrylate or quaternary ammonium salts thereof The emulsion is broken, enabling recovery and reuse of the organic portion of the emulsion A M Pavilcius and M A Latko, assigned to Nalco Chemical Co Feb. 27, 1979 3 pp (252-301 1W) Filed: 12-14-77 (860,542). US 4,142,952-In the recovery of copper from an ore leach solution, the solution is contacted with a water-immiscible organic solvent containing 5 to 20 g/L of o-hydroxyaryloxime and 2 to 20 times the weight of the o-hydroxyaryloxime of nonylphenol The loaded solvent phase is separated from the aqueous phase and stripped with sulfuric acid Copper is recovered rapidly and in high yield from aqueous solutions containing high copper concentrations R F Dalton, as¬signed to Imperial Chemical Industries Ltd Mar 6, 1979 6 pp (204-106) Filed 1-3-77 (756,067). Priority: United King¬dom, 1-30-76 (3788/76), 6-15-76 (24722/76), and 10-21-76 (43711/76). Same- British 1,549,615, dated Aug. 1, 1979 US 4,148,631-In the recovery of nickel and cobalt from a mixed sulfate ore leach solution, both metals are extracted by means of a cationic extractant, the loaded extractant treated with an aqueous chloride or thiocyanate solution to back extract the cobalt, and the cobalt then recovered by solvent extraction or ion exchange with an anionic extractant Recovery is effected in a relatively few extraction steps. F Babjak, V A Ettel, and K. R Dymock, assigned to Interna¬tional Nickel Co , Inc, Apr. 10, 1979 6 pp (75-101 BE) Filed¬7-27-78 (928,401). Priority- Canada, 12-28-77 (293,967) US 4,148,813-An improved extractant for use in the recov¬ery of nickel and cobalt from an ore leach solution comprises a water immiscible organic solvent system containing solubilized mercaptide ions, e g , dodecanethiol. Cobalt and nickel mercaptides solvated in the organic phase are easily stripped in the presence of carbon monoxide and an aqueous alkaline solution A. S. Rappas and J. P. Pemsler, assigned to Ken¬necott Copp

Jan 1, 1980

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.&apos; Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By J. B. Clark, A. S. Yue

PfANN1 has shown that when a cylinder of molten binary alloy freezes directionally, the solute distribution can be described analytically by cg=k(l-g)k-1 [1] in which Cg is the solute concentration in the solid at the point where a fraction g of the original liquid has frozen and Co is the initial solute concentration. The term k is the effective distribution coefficient of the solute and is defined as the ratio Cx/CL where Cl is the solute concentration in the main body of the liquid. Both the slope and the intercept at -log (1 - g) = 0 of a logarithmic plot of Eq. [I.] provide a measure of k. Under conditions of freezing where diffusion in the solid is negligible and the solute concentration in the liquid is uniform, the effective distribution coefficient k, derived as above, is equal to the equilibrium distribution coefficient taken from the phase diagram. However, under ordinary freezing conditions, even though solid-state diffusion is negligible, the solute rejected from the freezing solid does not have sufficient time to diffuse uniformly throughout the main body of the liquid. A concentration gradient is formed in a boundary layer in front of the advancing solid-liquid interface as pointed out by Rutter and Chalmers.&apos; Thus, under these conditions, the concentration of the freezing liquid in the boundary layer is higher than that predicted from the equilibrium phase diagram and consequently the effective distribution coefficient k, obtained from directional freezing experiments, is larger than the equilibrium distribution coefficient. The symbol k will designate the effective distribution coefficient in the discussion which follows. In this paper, the determination of the effective distribution coefficient is demonstrated for several dilute binary alloys and a polynary magnesium alloy. The effect of freezing rate on the value of the derived k is presented in detail. An example for the calculation of the solidus in a dilute binary solution using the experimentally determined effective distribution coefficient is given. MATERIALS STUDIED Binary magnesium alloys of copper, nickel, and zinc containing approximately 0.10 wt pct solute and a polynary alloy containing approximately 0.10 wt pct each of several elements were selected for study. The spectrographic analyses of these alloys are given in Table I. The analyses are believed accurate to within +5 pct of the stated value. EXPERIMENTAL PROCEDURE Extruded rods of the alloys, 3/8 in. in diam and 11 in. long were used for directional freezing studies. The alloy rods were melted horizontally in a high-purity graphite boat by a Nichrome-wound tube furnace which moved parallel to the length of the rod. The boat was supported inside a Vycor tube suitably connected to provide a protective atmosphere of dry SO2. For an experimental run, the following procedure was used. The alloy rod was cleaned in dilute HNO, and dried. The graphite boat containing the alloy rod was placed within the Vycor tube and the tube connected to the gas train&apos; The &apos;ystem was purged for 20 min with dry argon and then a flow of dried SO, was maintained for the duration of the run. The movable furnace was positioned and either all or a desired portion of the alloy rod was melted. After attainment of steady-state temperature gradients the molten bar was solidified from one end to the other at a controlled rate by pulling the furnace along the length of the bar at the desired speed. At the conclusion of the run, the directionally frozen alloy rod was analyzed spectrographically at 1 1/4-in. intervals.

Jan 1, 1961

By FORTUNATO PEREIRA

(San Francisco Meeting, October, 1911.) I. GENERAL DESCRIPTION. The Department of Narino (formerly included in the Department of Cauca) is a narrow band about 170 km. (100 miles) wide in the southern part of the Republic of Colombia, FIG. 1.-SKETCH-MAP OF THE SOUTHWESTERN PART OF COLOMBIA. near the boundary of Ecuador, as shown in the sketch-map, Fig. 1. Its capital is Pasto, a small city of 25,000 inhabitants; the principal towns are Túquerres, Cumbal, Ypiales, Barbacoas, and Tumaco. The port on the Pacific ocean is Tumaco, and traffic in the interior is carried partly on the Patia river (steam navigation to the fluvial port of Barbacoas), and afterwards overland over poor roads by human bearers or on mule-back.

Aug 1, 1912

The 114th (New York) Meeting of the Institute will be held in the third week of February, 1917. The Committee on Papers and Publications has set Dec: 1, 1916; as the closing date for the receipt of manuscripts intended for this meeting. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committee they must be sent to those committees enough in advance of the time to be forwarded and in the hands of the Secretary by the time specified. While Dec. 1, 1916, is the final closing date, it is a great advantage to get papers in as much before that time as possible as it enables them to be submitted in proof form to their authors. Papers received on or before Nov. 1, 1916, will, as far as possible, be published in the January Bulletin or earlier, thus giving good distribution among the members in advance of tile meeting. The Institute&apos;s records show that the discussion of papers is very rnuch better when they are distributed somewhat in advance of the meeting instead of in the Bulletin which goes out immediately preceding the meeting.

Jan 9, 1916

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation (Drake, 1972), Table 1. In 1970, the production of sand and gravel totaled 944 million tons valued at $1.1 billion. California, which leads the nation with more than 140 million tons, together with Michigan, Ohio, Minnesota, Illinois, Wisconsin, and New York, account for 43 % of the total production in the nation. In commercial usage, "sand" applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No, 4 sieve (4.76 mm openings). "Gravel" consists of rock or mineral fragments larger than 4.76 mm, ranging up to 3%-in. maximum size. The construction industry consumes 96% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster.

Jan 1, 1975

By D. L. Albright, R. W. Kraft

Solidification experiments were conducted with the objective of testing the theory of eutectic colony formation. Appropriate control of variables in tests on a series of high-purity aluminum-copper specimens of eutectic composition resulted in the observation of three types of eutectic microstructures, these being a unique structure consisting of lamellae essentially parallel to one another, a banded structure, and the colony structure. Lamellar faults, which are morphologically similar in many respects to edge dislocation models in crystals, produced a complex substructure in these specimens. SOLUTE rejection at the advancing solid-liquid interface of a unidirectionally solidified single-phase metal can cause the liquid immediately in front of the interface to become constitutionally super-cooled below the equilibrium liquidus temperature. Constitutional super-cooling occurs if the solidification rate, R, is too rapid, or if the thermal gradient in the liquid at the interface, G, is too low. 1 This constitutionally supercooled layer in turn stabilizes a cellular rather than a planar interface.&apos; A similar cellular interface has been observed when lamellar and other types of eutectics were unidirectionally solidified, and it has been shown that the cellular interface led to the formation of eutectic colonies.&apos; The lamellar structure is fan-shaped at the edges of colonies (which correspond to valleys or grooves in the cellular interface) because the lamellae grow normal to the local interface. One of the possible mechanisms which might cause the formation of the cellular interface, in the case of solidifying eutectic alloys, is constitutional supercooling of the liquid with respect to a third component rejected by both phases of the eutectic.3,4 On the basis of the analogy between the solidification of single-phase metals and binary eutectics, a eutectic alloy should solidify with a planar interface if the ratio of G/R is sufficiently high to compensate for any impurity which might be present and causing constitutional supercooling. The fan-like microstruc-ture of eutectic colonies should not occur under these conditions and the lamellae should be parallel to one another and to the solidification direction for extended distances. The experiments conducted in this investigation were designed to test these ideas. Following a resume of the experimental procedure, the various microstructures observed during the study are described, and their relationship to the growth conditions which produced them is discussed. EXPERIMENTAL PROCEDURE The eutectic between an aluminum solid solution and 0 phase (approximate composition CuA12) was chosen for this work for the following reasons: it was known that a lamellar structure forms, the eutectic temperature is low enough to facilitate experimental work, and the components can be procured commercially in a very pure form. High-purity copper (est. 99.999 pct Cu, obtained from National Research Corp.) and spectrographic aluminum rods, having impurities other than copper estimated to be Zn-15 ppm, Mg-10 ppm, Fe-3 ppm, Na-2 ppm, Cd-1 ppm, and Mn < 1 ppm, were melted in a stabilized zirconia crucible in a vacuum induction furnace at a pressure of 10 pof Hg. The melt was superheated to about 1000°C to assure mixing, cooled to 780°C and cast into an investment mold which yielded sixteen cylindrical specimen blanks 1/2 in. in diam and 5 1/2 in. long. The casting was allowed to solidify under vacuum. This master heat had an analysis of 32.6 wt pct Cu and 67.4 wt pct A1 by difference. The cylindrical specimen blanks were remelted and solidified unidirectionally in an apparatus illustrated schematically in Fig. 1. An RF induction coil heated

Jan 1, 1962

By Y. C. Liu

THE existence of mechanical twins in bcc metals has long been known. With recent intensive interest in the mechanism of twin formation and its role in plasticity and crack initiation, a study of the general Characteristics of twin intersection appears pertinent. The scope of the present note will be limited to the crystallography of the twin intersections of (112) twins, without consideration of its mechanism, movement of atoms, crystal structure, or the strain energy involved at such an intersection. The twinning elements of (112) twins are considered to be K1 = {112}, n1 = (111) and K2 = {112}, n2 = (111) with a twin shear of 0.707. The crystallographic features of twin intersections have been worked out in detail by Cahn.1 The present work applies the general principles postulated by Cahn to the intersections of (112) twins. The basic conditions for the twin intersection are: 1) The trace of crossing (A) and the secondary (C) twins in the planes of the crossed twin (B) must be parallel. 2) The direction (n1) and magnitude (s) of shear must be identical in the crossing and secondary twins. Also the sense of shear must be the same. These two conditions have to be fulfilled in order to maintain geometrical continuity at the twin interfaces. Fig. 1 shows the perspective representation of how these two conditions are fulfilled at the intersection. This type of intersection will be named Type-I. It is the purpose of this note to point out the existence of another type of intersection, Type-II, as shown in Fig. 2. In this type of intersection, the crossing twin A remains straight and the crossed twin B has been bent. The two conditions laid down by Cahn must also be met. This leads to the following corollary conditions: 1) The interface between twins B and C must be parallel to the twin habit of crossing twin A. 2) n1c must be parallel to n1A. 3) The twin shear (s) of twin C must be exactly equal to and in the same sense as that of crossing twin A. Thus, in order for the Type-II intersection to take place, the twining elements of secondary twin C must fulfill the above three conditions with respect to crossing twin A. Let K1 of crossed twin B be (112). All indices of the matrix can therefore be converted into new in-

Jan 1, 1963

By George Beavers

FLASH roasting of iron concentrate is in the experimental stage at Copperhill. The problem is peculiar in that the iron concentrate is predominantly pyrrhotite; the ratio of that mineral to pyrite being 5 to 1. Results so far indicate that the heat, generated in roasting a material containing 52.0 per cent iron and 38.0 per cent sulfur, requires special handling and for this reason the installation costs per ton of roaster feed may be too great to compete with hearth roasting. Interesting features of flash roasting at Copperhill are: 1. The sulfur dioxide content of the roaster exit gas can be varied between wide limits. Eight per cent sulfur dioxide gas, with 1.30 per cent sulfur in the calcine, has been common practice and gas up to 13.0 per cent sulfur dioxide has been possible. 2. Temperatures of the exit gases are very high. When roasting 60 tons or more of iron concentrate per 24 hr. in a modified Wedge roaster, the temperature in the roaster rises to 2000° F. and the calcine is lowered to 0.20 per cent sulfur. If the entire roaster system could be constructed to withstand such temperatures, ideal roasting conditions would obtain as regards sulfur elimination and tonnage roasted.

Jan 1, 1934