Search Documents

By E. A. Anderson

THE copper-zinc phase equilibrium diagram has been the sub-ject of many investigations. Until recently, however, the boundary of the terminal solid solution of copper in zinc (eta) has not been thoroughly investigated. This paper reports determinations of the solid solubility of copper in zinc at temperatures from 100° to 400° C., the course of the liquidus and solidus for the eta solid solution and determinations of the peritectic temperature and peritectic point for the reaction between epsilon and the melt to form eta. The liquidus of the eta phase was determined by thermal analysis and the solidus by the microscopical examination of specimens quenched from temperatures above and below the solidus. The temperature of the peritectic horizontal was obtained by thermal analysis and the com-position at the peritectic point was determined by extrapolation of the solid solubility boundary of the eta phase to the peritectic horizontal. The solid solubility boundary of the eta solid solution was investigated very carefully. Particular care was used to achieve equilibrium in the alloys at each temperature selected. The X-ray, electrical con-ductivity and microscopical methods were used in determining the solid solubility limits. The X-ray method measures the changes in the solvent lattice with increasing solute content and in this manner locates the composition of the alloy at which no further change in the solvent lattice takes place, the limit of solid solubility. The method of electrical conductivity measures the conductivity of the alloys of a graded series of compositions, whereby the solubility limit is indicated by a discontinuity in the conductivity-

Jan 1, 1934

By Jei Y. Choi, P. G. Shewmon

Using a scratch smoothing technique, the magnitude and the ratio of the surface diffusion coefficients (D,) in two orthogonal directions have been measured on copper for over 100 different surface orientations. Anisotropy was found for all surface orientations except those lying near the (100) and (111); however, these anisotropies were rarely greater than 2.0. The direction of maximum D, appears to coincide with the direction of step edges on any given surface, and if no such steps exist, no anisotropy is found. Thus the jump frequency along a step edge is shown to be faster than the frequency of a jump over the step. The values of Ds and AH for the (100) and the (111) orientations agree quite well with those obtained earlier by the grain boundary grooving technique. It is proven that the directions of maximum and minimum D, (the principal axes) for any surface orientation are known if the perfectly ordered plane corresponding to the given surface orientation possesses a plane of mirror symmetry. Thus the principal axes of D, for orientations lying along the sides of the unit stereo-graphic triangle are always known independent of the extent of thermal disorder or impurity adsorption. The merits and shortcomings of King and Mullins' recently published equations relating Ds to the rate of scratch smoothing are discussed. 1N an earlier paper the authors have reported the variation of the surface diffusion coefficient (Ds) with surface orientation on copper.' In that study Ds was determined from the rate of growth of grain boundary grooves on symmetric bicrystals. This gave values of Ds from 850° to 1070°C in a given direction on each of the six surfaces. It was found that the activation energy for surface diffusion was essentially the same for all six surfaces. The theory developed to explain these data assumed that the free energy of any given type of surface site depends only on the number of nearest neighbors the atom has. This same theory predicted that on any given surface Ds should be independent of direction. The primary aim of this study was to check the validity of this prediction for a wide range of surface orientations on copper. The growth of grain boundary grooves is ideal for studying Ds in a given direction on a given surface over a range of temperatures, because the same specimen can be repolished and used again. However, there is considerable work involved in growing a symmetric bicrystal, and for a survey of Ds in two or more directions on many surface orientations, the technique would be arduous. A better technique appeared to be the scratch method used primarily by Mykura. 2 If a scratch is placed in a surface whose surface tension is independent of orientation, the surface will smooth out in time under the influence of surface tension. To determine D, from this flattening, Blakely and Mykura2 used an approximate solution which was assumed to describe the rate of flattening. Recently King and Mullins3 (hereinafter K and M) have given a more exact analysis of the flattening of an isolated scratch. A second aim of this paper was to check the validity of this newer analysis and compare the values of Ds determined thereby with the values obtained from grain boundary grooving techniques. EXPERIMENTAL PROCEDURE In an effort to work with a particular predetermined surface orientation, light orthogonal scratches

Jan 1, 1963

By Richard W. Markley

The predominant methods for mining coal in the USA are room and pillar and longwall. Approximately 95 percent of the coal is mined by room and pillar and 5 percent by longwall. The U.S. Department of Energy (DOE) has an ongoing program to improve the rate, quality, and cost effectiveness of stabilizing the roof for both of these mining systems. In room and pillar mining, the installation of permanent roof support is often the task which paces the system operation, and it thus controls the level of production achieved during any mining shift. Two automatic roof bolt insertion equipment developments are discussed, as well as a flexible drill for operation in thinner seams. Progress will be reported on under- ground trials of a particular flexible drill which has been combined with a bolt inserter to form a compact, reliable module for retrofitting to continuous mining machines. In longwall mining, the use of hydraulic supports on the working face provides roof stability. The DOE has several trials ongoing with shield- type supports in difficult strata conditions which are described, as well as a co-funded project with the Bureau of Mines on a resin injection remedial method for consolidating a shear zone at one site. A project to improve the match of strata conditions to shield design is also described, which involves the use of a 1360 tonne vertical load mine roof simulator.

Jan 1, 1983

SMELTING is a thing essential to the end for which ores are sought, for without it every ore is a useless stone. This art is especially needed by those who, drawn on by hope, have mined ores in large quantities with great expense and effort. For this reason it is worth while to use one's wits and, if ordinary ways should not suffice, to consider how to find new ways of smelting the ores in order to extract the metals and to purge them of their earthiness. For this reason I shall now tell you of blast and other furnaces, and I shall also tell you, in order that you may be warned, that whoever wishes to do this well must first look at the nature and quality of the ore. You will already have had enlightenment on this from the experiments on assaying and with this as guiding star it is necessary to make ingenious structures and to provide for-the other needs as necessary, for one ore requires iron and another lead. Since I have already spoken of these in their own places on their ores, it is not necessary at present that I repeat, but here I wish to speak only of copper ore as a companion of silver and gold, and of where art is most required and where difficulties chiefly appear. For these things a machine must be built that is convenient to a good water supply in order to continue the work more easily. Its wheels should be large and easily moved, constructed in such a way that the force of the water lifts the bellows that are placed at the tuyère to direct the blast inside the furnaces that are to smelt the ores. For this, attention must first be given to the site of the machine, the quantity of water, and its fall; then to the wood for building the machine and for making charcoal; then to the stones that are used for the blast furnaces; then to the provision of good bellows that are wide, long, and full in their sides and made of cloth, for the better these are, the more they quicken the power of the charcoal

Jan 1, 1942

By S. Lipson, H. W. Antes, H. Rosenthal

A study was made of the effect of ingot structure on the strength and ductility of high-strength wrought-aluminum alloys. It was found that a fine-cast structure facilitated complete homogenization which, in turn, resulted in significant increases in ductility and strength. A completely homogenized 7075-T6 alloy developed tensile properties of 85,000 psi UTS, 75,000 psi YS, with 40 pct RA. Completely homogenized 7001-T6 alloy tensile properties were 102,000 psi UTS, 99,000 psi YS, with 19 pct Ra. A method was devised for making small ingots having secondary dendrite arm spacing of less than 10 u. This method involved multiple-pass arc melting of commercial rolled plate with a tungsten electvode. This material could be completely homogenized after 3 hr at 900°F; homogenization of the original plate material was not complete after 120 hv at 900°F. Degree of homogeneity was determined by use of metallographic and electron-microprobe analyses. The electron-micro-probe study also showed the preferential segregation of solutes in the microstructure. HIGH-strength aluminum alloys, such as those of the 7000 series, usually freeze by the formation and growth of dendrites. The dendrite arm spacing (DAS) depends on the rate of solidification.' Commercial ingots are usually direct chill-cast to promote more rapid solidification, but, due to the large mass of the ingot, localized solidification times are long and a large DAS results. During solidification, solute elements are rejected by the solid as it forms, causing enrichment of the liquid and ultimately solute-rich interdendritic regions. In order to attain a homogeneous ingot, the segregated solutes must diffuse across the dendrite arms. The larger the DM, the longer the time for complete homogenization. In the case of commercial ingots, the DAS is so large that the time for complete homogenization is prohibitively long and, therefore, second phases or compounds are always present. These un-dissolved phases are carried over to the wrought material during processing, resulting in an impairment of strength and ductility. In addition, the mechanical fibering of the undissolved second phases or compounds during working results in mechanical property anisotropy. If complete homogenization could be attained, higher ductility could be expected. The realization of higher ductility at current strength levels is a desirable objective; however, if higher-strength alloys were wanted, it might be possible to sacrifice some of this ductility by adding more solute elements and produce even higher-strength alloys than are currently available. Further, if complete homogenization leads to more efficient utilization of solute elements, then more dilute alloys should have relatively high strengths with very high ductility. In all instances, it would be expected that the degree of mechanical property anisotropy due to mechanical fibering would be reduced. Therefore, it was the purpose of this investigation to produce cast structures that would facilitate homogenization and to determine the effect of homogenization on the properties of high-strength, wrought-aluminum alloys. MATERIAL CLASSIFICATION Commercial Alloys. In order to illustrate the non-homogeneous condition that exists in commercial high-strength, wrought-aluminum alloys, typical micro-structures of 7001, 7075, and 7178 are shown in Fig. 1. The chemical compositional specifications of these alloys are given in Table I. It can be seen in Fig. 1 that a considerable amount of undissolved second-phase material is present in each of these alloys. The solute elements associated with the undissolved phases were identified by electron microanalyses. Back-scattered electron images and characteristic X-ray images of the three commercial alloys are shown in Figs. 2, 3, and 4. These data indicate that the second phases are regions of high copper and high iron-copper concentrations. The second-phase material also was analyzed for magnesium, zinc, manganese, chromium, and silicon, but no significant enrichment above that of the matrix was found. Therefore, the problem of homogenization resolved itself into one of dissolving the copper-rich and the iron-copper-rich second phases. In order to accomplish this objective, two approaches were made. The first was to reduce the iron as low as possible since this element has a maximum solid solubility of 0.03 pct in aluminum. The second was to produce cast structures with finer DAS to facilitate dissolving the second phases. Commercially Produced High-Purity Alloys. A special high-purity, 2000-lb ingot of 7075 alloy was made by a commercial producer. This alloy contained the following weight percentages of solutes: 5.63 Zn, 2.48 Mg, 1.49 Cu, and 0.21 Cr. All other elements combined were less than 0.02 pct by wt including iron and silicon at less than 0.01 pct each. The ingot was cast and processed into rolled plate using standard commercial techniques. Microstructures of standard commercial 7075 and the special high-purity 7075 are shown in Fig. 5. It can be seen from this figure that the high-purity alloy has less undissolved second-phase material, but a significant amount was still present. The second phase in the high-purity material did not contain iron but it was found to be enriched with copper. The slight effects of the increased purity and de-

Jan 1, 1968

By K. Stout, E. Van Eeckhout, L. Friel

Previous research at the Montana College of Mineral Science and Technology indicated that it is practical and economically feasible to place stiff back- fill in a cut-and-fill stope. This backfill would reduce wall closure and high stress buildup in pi1llars, thus alleviating rockburst potential. Three ;topes from the Sunshine Mine, of the Coeur d’Alene Mining District, were chosen for a test verification of this concept. Although the first stope was lever mined beyond the initial cut (for economic reasons), some vibrating wire stressmeter results were obtained and found to compare favorably with numerical predictions. Some other instrumentation devices were built and tested, but never installed .

Jan 1, 1984

By HENRY FA

HENRY FAY (communication to the Secretary*).-In reply to the discussion of my paper, I wish to take this opportunity to express my appreciation to the Chairman and the various gentlemen who have taken part. I regret that others have not offered criticism, for honest differences of opinion often lead to the truth, and suggest new lines of work. An experiment has been made which bears on Prof. Sauveur's discussion and which helps to emphasize the conclusion that cementation is not a factor in the hardening of: the surface. Dr. Langenberg, of the Watertown Arsenal, has heated for me, in vacuo at 1,000° C., a piece of the metal containing a hard surface. The microstructure shows uniform distribution of carbon throughout the metal, showing that no carbon has been added to .the surface and heating in vacuo has prevented any oxidation of the surface.

Jan 6, 1917

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--'¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker' on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski' investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By A. H. Tousley, C. L. Vickers

The author presents a history of the development of the Port of Long Beach from its beginning in 1905 to the present construction of a new bulk loading facility. In describing this new facility, emphasis is placed on such aspects as rail car and truck handling, gravity yard, rotary car dumping, bottom dumping, car dumping equipment, feeding and conveying, ship-loader-stockpiler, stockpiling and reclaim, dust control, and construction problems. Development of the Port of Long Beach, Calif. (see Fig. I), began in 1905. In that year private Long Beach interests acquired 800 acres of marshland in the Inner Harbor area and initiated a program of channel dredging and land reclamation. Efforts to establish a municipal port began a short time later and culminated in the opening of Pier 1 in 1911. An event of even greater significance to the port future also occurred in 1911. This was the tideland grant enactment by the state legislature that conveyed to the city of Long Beach all of the state's rights in the tidelands located within the city boundaries. The grant stipulated that all revenue produced from the tidelands be used for the development of navigation, commerce, and fisheries. During the next 15 years up to 1926, the port's commercial growth was steady, although relatively slow. During this period, several fundamental steps in the development of a major harbor were accomplished. These included the creation of the Board of Harbor Commissioners in 1917, the dredging of the Inner Harbor and entrance channel to accommodate deep draft vessels, and the correction of a serious silting problem through construction of the Los Angeles River Flood Control Channel. These efforts bore fruit during the ensuing 10 years in the establishment of more than $30,000,000 worth of industrial plants and private marine terminals in the Inner Harbor. Commerce over municipal wharves also increased more rapidly, and it became necessary to start the development of the harbor in a seaward direction. In 1936, oil was discovered in the harbor area, and the first Harbor Dept. well was brought in 2 years later. It soon became evident that the city of Long Beach would receive substantial revenue that, under the terms of the state grant of 1911, must be used in the development of the port. It was further realized that to properly guide and coordinate such development, a long range comprehensive plan was essential. The Board of Harbor Commissions contracted with G. F. Nicholson and J. F. Collins, consulting engineers, for the preparation of such a report that was completed in 1940. The Nicholson-Collins report proposed the development of an East Basin, between the entrance channel and the Los Angeles River, and a West Basin in the area now occupied by the Long Beach Naval Shipyard. Twenty full-size berths were to be provided in the East Basin and more than fifty berths in the West Basin. The report recommended extensive modern terminal facilities for handling waterborne cargo. Attention was given to improvement of the street and highway system to give better vehicular access and to avoid congestion within the port. To a large extent the recommendations of the Nicholson-Collins report were followed in the subsequent development of the East Basin. This development was greatly accelerated by World War 11, with its need for increased oil production and additional shipping facilities. The wartime and immediate postwar construction was largely concentrated on Pier A, with the development of Piers B, C and D following in more recent years. An important factor in the planning of these piers was their dual function as oil drilling sites and cargo piers. The Navy's acquisition of the West Basin area made it necessary to depart from the Nicholson-Collins plan and find other areas for future expansion. At the present time only one Inner Harbor Port-owned area having protected deep water frontage remains undeveloped. This is the property fronting on Channel 2 in the Inner Harbor acquired in December 1957, from Pacific Dock and Terminal Co. The growth of the port has been in a southerly direction since the construction of the Long Beach Naval Shipyard in the West Basin area. Recent extension of Piers F, G and J into the ocean follows typical port construction methods developed during the expansion of the Middle Harbor during the last 20 years.

Jan 1, 1963

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

By P. G. Shewmon, H. E. Collins

We have studied the effect of adsorbed sulfur on the surface self-diffusion of copper using eight diflerent surface orientations and the grain boundary grooving method. The eight orientations studied were the four lying near the low-index surfaces—(loo), (Ill), and two directions in the (110)-plus four higher-index surfaces. Surface-diffusion measurements were made over a range of HZS concentrations (in Hz) from 3 to 1500 ppm between 830°and 1050°C. The results can be divided into two groups—Group 1 contains the two (110) surfaces while Group 2 contains the remaining six surfaces. In Group 1, increasing the temperature increases the effect of Hz S on DS for the Hz S range 5700 ppvn. Qs and Do increase with increasing H2S concentration in this Hz S range. Beyond this range, increasing the temperature decreases this effect on D,; also Q, and Do decrease. In Group 2, increasing the telnperature decreases the effect of H2 S on D, for the H2S range studied, and Qs and Do decrease with increasing Hz S concentration. In any study of surface phenomena, there invariably arises the question of the possible presence of and effect of adsorbed impurities. Such questions are well-founded since the presence of adsorbed atoms can sometimes produce marked changes in the kinetics of surface-energy-driven processes. In the last few years, values of the surface self-diffusion coefficient, D,, have been determined on a variety of metals by studying the decay of scratches or the growth of grain boundary grooves.L~3-L0~L3 Yet there has been relatively little work done in which the concentration of an adsorbed impurity was systematically varied and the effects observed. Work of this sort would provide some basis in fact for the assertions often made about the ro1.e of adsorbed impurities in the differences between the results of different workers in different atmospheres and on different metals. It also is relevant to those cases in which surface monolayers produce profound effects in commercially important processes. The most marked example of such effects is the ability of nickel or palladium to increase the sintering rate of tungsten by many orders of magnitude.' The aim of this work was to study the effect of sulfur partial pressures on the surface self-diffusion of copper. It was felt that this in conjunction with a study of the degree of adsorption and type of active sites involvedL8 would provide a wide range of data for one system and hopefully lead to some insight into the mechanism by which sulfur adsorption influences copper diffusion. The main reasons for choosing the Cu-S system were, first, faceting was reported not to accompany the adsorption of sulfur. This is required if our experimental technique is to work. Second, Oudar has determined a high temperature adsorption isotherm for this system, an event which puts the Cu-S system almost in a class by itself.I4 EXPERIMENTAL PROCEDURE Initially, we considered studying the effect of an adsorbed impurity on surface self-diffusion of copper using isolated (or single) scratch smoothing as the technique and oxygen as the impurity. Copper was chosen as the material because the effects of orientation and anisotropy of the surface self-diffusion coefficient, D,, of copper in a dry hydrogen atmosphere had been studied extensively by Gjostein' and by Shewmon and ~hoi.~,~ The isolated scratch technique was chosen because both the effects of surface orientation and anisotropy of D, in a given surface could be easily studied with this method.~ Oxygen was tried as the impurity because Robertson and Shewmon""~ had studied its adsorption on copper at 1000°C over the range of oxygen partial pressures of 10"22 to 10-l3 atm. After several preliminary runs, it became evident that neither the scratch technique nor the impurity oxygen would be satisfactory for this work. Scratching deforms an annealed surface so that the region near the scratches recrystallizes, thereby disrupting the scratch profiles. One can avoid this by deforming the specimen sufficiently before scratching to give complete recrystallization on subsequent heating.4 However, as a result of Gjostein's success in scratching and annealing undeformed gold single crystals without local recrystallization,13 we attempted something similar with copper single crystals using a 0.7-mil diamond phonograph needle mounted in a Tukon hardness tester. All specimens recrystallized upon being annealed. Also, some copper specimens were sent to Gjostein to be scratched using his technique. The results were the same. As a result, the scratch technique was dropped in favor of the grooving of symmetric grain boundaries. Preliminary work using oxygen showed that faceting began to occur before oxygen adsorption had any measurable effect on D, at 938°C (at Pbo/P, = 0.12). Since heavy faceting would interfere with the measurement, we decided to use a sulfur-containing atmosphere (H2S/H2). Work by Oudar and Benard' and Robertson" showed that sulfur absorbed on copper and that faceting was not observed.

Jan 1, 1967

By N. F. Dyson, T. R. Scott

The iilzfluence of catalytic agents on the oxidation of ZnS has been studied under pressure leaching conditions, using a chemically prepared sample of ZnS which was substantially unreactive on heating at 113°C with dilute sulfuric acid and 250 psi oxygen. Nurnerous prospective catalysts were added at the ratio of 0.024 mole per mole ZnS in the above reaction but pvonounced catalytic activity was confined to copper, bismuth, rutheniuwl, molybdenum, and iron in order of. decreasing effectiveness. In the absence of acid, where sulfate was the sole product of oxidation, catalysis was exhibited by copper and ruthenium only. Parameters affecting the oxidation rate were catalyst concentration, temperature, time, oxygen pressure, and a7riount of acid, the first two being most important. The main product of oxidation in the acid reaction was sulfur, with trinor amounts of sulfate. An electrochemical (galvanic) mechanism has been suggested for the sulfuv-forming reaction, whereby the relatively inert ZnS is "activated" by incorporation of catalyst ions in the lattice and the same catalysts subsequently accelerate the reduction of dissolved oxygen at cathodic sites on the ZnS surface. Insufficient data was obtained to Provide a detailed mechanism for sulfate fornzation, which is favored at low acidities and probably proceeds th'rough intermediate transient species not identified in the preseni work. THE oxidation of zinc sulfide at elevated temperatures and pressures takes place according to the following simplified reactions: ZnS + io2 + H2SO4 — ZnSO4 + SG + HsO [i] ZnS + 20,-ZSO [21 In dilute acid both reactions occur but Reaction [I] is usually predominant, whereas in the absence of acid only Reaction [2] can be observed. Both proceed very slowly with chemically pure zinc sulfide but can be greatly accelerated by the addition of suitable catalysts, as suggested by jorling' in 1954. Nevertheless, an initial success in the pressure leaching of zinc concentrates was achieved by Forward and veltman2 without any deliberate addition of catalytic agents and it was only later that the catalytic role of iron, present in concentrates both as (ZnFe)S and as impurities, was recognized and eventually patented.3 It is now apparent that another catalyst, uiz., copper, may have also played a part in the successful extraction of zinc, since copper sulfate is almost universally used as an activator in the flotation of sphalerite and can be adsorbed on the mineral surface in sufficient amount The importance of catalysis in oxidation-reduction reactions such as those cited above has been emphasized by various writers and Halpern4 sums up the situation when he writes that "there is good reason to believe that such ions (e.g., Cu) may exert an important catalytic influence on the various homogeneous and heterogeneous reactions which occur during leaching, particularly of sulfides, thus affecting not only the leaching rates but also the nature of the final products." Nevertheless relatively little work has appeared on this topic, one of the main reasons being that sufficiently pure samples of sulfide minerals are difficult to prepare or obtain. When it is realized that 1 part Cu in 2000 parts of ZnS is sufficient to exert a pronounced catalytic effect, the magnitude of the purity problem is evident. An incentive to undertake the present work was that an adequate supply of "pure" zinc sulfide became available. When preliminary tests established that the material, despite its large surface area, was substantially unreactive under pressure leaching conditions, the inference was made that it was sufficiently free from catalytic impurities to be suitable for studies in which known amounts of potential catalytic agents could be added. The first objective in the following work was to identify those ions or compounds which accelerate the reaction rate and, for practical reasons, to determine the effects of parameters such as amgunt of catalyst, temperature, time, acid concentration, and oxygen pressure. The second and ultimately the more important objective was to make use of the experimental results to further our knowledge of the reaction mechanisms occurring under pressure leaching conditions. The fact that catalysts can dramatically increase the reaction rate suggests that physical factors such as absorption of gaseous oxygen, transport of reactants and products, and so forth, are not of major importance under the experimental conditions employed and an opportunity is thereby provided to concentrate on the heterogeneous reaction on the surface of the sulfide particles. As will appear in the sequel, the first of these objectives has been achieved in a semiquantitative fashion but a great deal still remains to be clarified in the field of reaction mechanisms. EXPERIMENTAL a) Materials. The white zinc sulfide used was a chemically prepared "Laboratory Reagent" material (B.D.H.) and X-ray diffraction tests showed it to contain both sphalerite and wurtzite. The specific surface area, measured by argon absorption at 77"K, varied between 3.9 and 4.6 sq m per g. Analysis gave 65.0 pct Zn (67.1 pct theory) and 31.9 pct S (32.9 pct theory). Other metallic sulfides (CdS, FeS, and so forth) used in the experiments were also chemical preparations of "Laboratory Reagent" grade. Samples of mar ma-

Jan 1, 1969

By D. R. Mash

A strong yield point with attendant enhanced mechanical properties was found in commercially pure beryllium under certain conditions of heat treatment. Beryllium specimens also responded to both quench and strain aging treatments. Based on these results, a possible means of obtaining increased normal temperature mechanical properties is suggested. COMMERCIALLY pure beryllium has been found to exhibit the yield point phenomenon and several other aging manifestations under certain conditions of heat treatment. This behavior is not surprising in view of the present accumulation of experience regarding such effects in numerous metals; but in addition to extending this experience to include beryllium, the present study is of interest because aging effects are generally associated with the presence of small amounts of solute elements. The well known lack of tensile ductility in beryllium at normal temperatures is also considered to be due to impurities in some way. In the present investigation, the view was taken that beryllium of commercial purity (greater than 98 pct) should be considered as a dilute alloy and that precipitation phenomena may well exist which could lead to enhanced mechanical properties. In connection with this possibility, published data on the variation of mechanical properties with temperature are of interest. For example, Fig. 1 illustrates the variation of ductility (percentage of elongation) and ultimate strength as a function of temperature for beryllium of various histories.* Although these curves are somewhat schematic in nature, they clearly indicate the possibility that precipitation of an unstable phase and/or aging effects occur during tests in the region 400" to 700°C. The existence of such behavior should be recognized as affecting the properties of the commercial material and perhaps can be employed advantageously. Experimental Method All testing was done at room temperature using a Baldwin universal testing machine. A microformer extensometer was used in conjunction with a micro-former-type stress-strain recorder. All tests were conducted at constant loading rate, the slowest rates being used. This corresponded to 120 lb per min in the 1200 lb full scale range and 300 lb per min in the 6000 lb full scale range. After the rate of loading was set in the elastic range of the material during the early part of the test, no further adjustments were made, allowing the test to proceed at that setting. In the plastic region of the curve above the yield region, strain rates of from 0.002 to 0.006 in. per min were regularly obtained. All experimentation was carried out on specimens machined from the same lot of beryllium, lot No. Y5036BP. Table I shows the chemical analysis as furnished by the supplier, Brush Beryllium Co., as well as the standard specifications to which commercial beryllium is produced. Both 1/4 in. thick hot pressed plate and ½ in. round hot pressed and warm extruded rods were obtained. The history of the material is reported to be as follows: 1—Beryllium metal plates, produced from a standard hot pressed QMV beryllium metal block 4x15x40 in., were cut off and finished machined to 1/4x6x12 in. flat plates. The original hot pressed block was made by hot pressing —200 mesh vacuum cast attri-tioned powder at about 1050°C under vacuum. 2—Beryllium rod was hot pressed and warm extruded. Extrusion billets were machined from the regular hot pressed blocks followed by extrusion at 425°C. The extrusion was done without jacketing, and graphite was used as a lubricant. The rods were then straightened at 720 °C, after which they were annealed at 800°C for 15 min. Both flat tensile specimens and round tensile specimens were tested. The former were machined from the plate stock into standard specimens according to specifications shown in ASTM E8-52T. The nominal cross-section was 0.25x0.500 in. and the gage length was 2 in. The round specimens were

Jan 1, 1956

By H. H. Podgurski, H. E. Knechtel

Annealed Fe-Al alloys do not react readily to form AlN when held at 500ºC in NH3-H2 gas mixtures, but do so upon the introduction of dislocatims. Nuclea-tion of the nitride phase occurs on dislocation sites. In turn, the growth of the aluminum nitride particles causes the ferrite phase to yield plastically, generating more dislocations for the nucleation process. The nitride phase extracted from an Fe-2 pct A1 alloy nitrogenated at 500°C was identified as stoichio-metric aluminum nitride with a hexagonal crystal lattice. THIS investigation reveals the role that dislocations play in initiating and sustaining the nitriding reaction in Fe-A1 alloys. As early as 1931 the work of Meyer and Hobrock1 suggested that the initiation of the nitriding reaction could involve a nucleation controlled process. Recently Bohnenka2 depicted the gas-phase nitriding process below 600°C as one of mixed control limited by nitrogen penetration through the surface, by nitrogen diffusion, by aluminum diffusion, and by nucleation of the nitride phase, Fig. l(a). In our research in a comparable alloy (0.57 pct Al) at 575ºC, we have observed a nitrogenation which we feel is better described by Fig. l(b). In the case of a 2 pct-A1 alloy partially nitrided at 500°C we propose the profiles shown in Fig. l(c). For a complete and accurate description of the process, a concentration profile of the dislocation density in the test specimen would be needed. EXPERIMENTAL Nitrogenization was conducted between 500" and 575°C in a variety of NH3-H2 gas mixtures on three Fe-A1 alloys: 1) zone-refined iron + 0.16 i 0.2 pct Al—levita-tion melt, 2) zone-refined iron + 0.57 0.02 pct Al— levitation melt, 3) plastiron + 2 pct Al—melted by induction heating. To demonstrate the effect of dislocations on reactivity, both cold-worked and annealed samples were investigated. All nitrogenation rate studies were conducted gravimetrically with a gold-plated invar balance4 contained in a gas-flow system. To avoid contamination of the specimens in the reaction zone of the system, the reaction chamber was constructed of high-purity dense alumina. The activity of nitrogen was fixed by specific NH3-H2 gas mixtures whose compositions were continually monitored by calibrated thermal conductivity gages and checked by chemical analysis. Variations of ± 0.1 pct NH3 could easily be detected by both methods. Throughout this paper the activity of nitrogen is defined as PN3 /PH23/2 , where PNH3, and Ph2 are partial pressures in atmospheres. Electron transmission, density measurements, and chemical analyses were made on specimens before and after nitrogenating in order to reveal structural and chemical changes. Similar studies as well as X-ray diffraction studies were conducted on nitride extractions from the nitrogenated 2 pct-A1 alloy. These extractions were obtained by the use of an anhydrous bromine-methyl acetate solution which dissolves the iron and leaves the insoluble nitrides as a residue. Hardness profiles were obtained on cross-sections of partially nitrided specimens to demonstrate the extent of nitriding through the thickness of the specimens. RESULTS AND DISCUSSION The nitrogen activity in the NH3-H2, atmospheres was never allowed to reach a level capable of producing iron nitride (Fe4N). Hence, the term nitriding as used in this paper refers only to the formation of aluminum nitride whereas nitrogenation refers to the total uptake of nitrogen regardless of how it is distributed throughout the alloy. The weight increases observed during the initial stage of a nitrogenating treatment are due primarily to the solution of nitrogen in the ferrite phase, particularly when starting with annealed specimens. Because this initial nitrogenation rate in the case of the 0.57 pct A1 alloy, see Figs. 2 and 3(a), was most rapid the weight change that occurred thereafter might be attributed to the nitriding reaction with the exception of a small weight increment due to the irreversible pickup of oxygen by aluminum. The oxygen (<70 ppm) came from traces of H2O and 0, in the hydrogen and ammonia gases. On the basis of discrepancies between total weight increase and the increase in the nitrogen content of the sample as determined by chemical analysis, it was estimated and later established by activation analysis, that as much as 200 ppm of oxygen were taken up by a fully nitrided Fe-0.57 pct A1 specimen at 575°C. Most of the oxygen could have been picked up from the nitriding atmosphere on the surface of the samples during cooling to room temperature. Even 50 ppm of water in the gas phase will become oxidizing to iron before the sample has cooled to room temperature. The lack of reactivity* of these alloys in the annealed

Jan 1, 1970

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of drainhole drilling on production capacity. Drain holes are those lateral holes which are sometimes drilled to assist in increasing the oil drainage into the main wellbore. The studies indicate that if the drainhole length i.r near 0.2 of the drainage radius, the increase in production capacity may be approximately 1.8, 2.08, trnd 2.33 for the case of one, two and four drain holes, respectively. If multiple drain holes are drilled, shorter holes are required to achieve a specific increase in production capacity than if one or two holes are drilled. To achieve increases in production capacities by factors near three it is shown that the drainhole lengths divided by the drainage radii must be approximately 0.64, 0.48, cnd 0.37 for the case of one, two and four drain holes, respectively. IN T RO DUCTION Kecent developments in drilling techniques have permitted the drilling of lateral or horizontal holes to increase the rate of production. The number of these drain holes may vary from 1 to 10, and they have been drilled laterally as much as 100 ft. Drainhole drilling at substantial depths is of recent origin but has been used in the Spraberry field of West Texas, the La Pas field in Western Venezuela, and certain fields in California. The diameter of the drain holes has been approximately 6 in. In drilling drain holes it is desired to know how much increase in production capacity may be expected, what additional benefit may be gained by drilling more than one drain hole, and what increase in production capacity may be brought about by lengthening the existing drain holes. In realization of the importance of lateral drilling, electrical model studies were made to provide quantitative estimates on the effect of drain holes on production capacity. ANALYSIS An electrical model was used in studying this problem. A wooden circular reservoir approximately 30 in. in diameter and 2 in. deep was filled with a dilute salt solution to a depth of 1 in. A copper band formed the periphery of the tank, and a copper wire was inserted in the center of the tank to represent the well. The drainage radius divided by the well radius was equal to 500. A diagram of this type model is shown in the inset of Fig. 1. An electrical potential was applied to the wire well and copper band at the periphery to determine the flow of current. Following this measurement copper wires of various length were soldered to the vertical wire well in such a manner as to simulate lateral wells drilled into the reservoir. Multiple lateral holes of various lengths were studied by varying the number and length of copper wires soldered to the vertical wire well. All multiple lateral wells were located symmetrically about the vertical well. The effect on production capacity by drilling an infinite number of lateral holes was studied by replacing the lateral hole with a copper disk. For each condition the flow of current was measured and compared with the flow of the vertical well only. The model which is thus described provides the steady state increases in production capacity which may be expected in some cases. The data conform to those which would be observed for a uniform homogeneous reservoir. The data may have primary application to those reservoirs producing above the bubble point. It is realized that few lateral holes are drilled in reservoirs of this type, but the data may be of some value in guiding future work or aiding to explain observed phenomena.

Jan 1, 1956

By William Benzon

Bethlehem Steel&apos;s Cambria Division coal cleaning and preparation plant, operated by Bethlehem Mines Corp., is located in Cambria County, Pa., about 2 ½ miles southeast of Ebensburg. Here, above ground, is the most modern coal preparation plant in the world. Below the surface is a new coal mine also referred to as "the most modern that could be built today." The preparation plant has a capacity of 1370 tons of clean coal per hr. It serves three Bethlehem mines, Heisley No. 31, Revloc No. 32, and the new Cambria Slope No. 33.

Jan 12, 1965

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-&apos;Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Since both rotary and jet piercing drills are used by the Iron Ore Co. at Smallwood, it is often desirable in planning to know in which regions of the orebody or new orebodies a particular drill will be the most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock properties. For rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes and the mine distribution curve for grinding factor index. A discussion is presented on the fuel oxygen ratios to be used in jet piercing and on the site gas sampling and analysis which has been used to set up the drills. The fuel has been cut back so that stoichio-metric conditions exist, carbon monoxide is drastically reduced and pop-up or exploding holes eliminated. No decrease in penetration rate has been observed contrary to the published results of previous workers. The blasting procedure and results at Smallwood are discussed and the operation of Iron Ore Co.&apos;s slurry pump-mix truck is also described briefly. Smallwood mine is part of the Iron Ore Co.&apos;s Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million tons of crude and 7% million tons of concentrate and pellets which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. For convenience the ore has been split-into the following classifications depending on the percentage of magnetics in the sample, shown in brackets: specularite (0 to 10%), specularite-magnetite (10 to 20%), magnetite- specularite (20 to 30%), magnetite (>30%). The order of classification also represents the order of increasing grinding difficulty - the specularite generally being the easiest and the magnetite the hardest. The orebody also contains a small percentage of waste materials consisting of limonite carbonate, quartz carbonate and quartz magnetite. The first two materials are among the softest in the mine, generally softer than the specularite, and the quartz magnetite is amongst the hardest. The bulk of the material in the mine is of the specularite-magnetite and magnetite-specularite classifications. As a result of test drilling at Smallwood in 1960 with rotary, jet and percussion drills, the Iron Ore Co. purchased four JPM-4 jet piercers for the bulk of production drilling and set up an oxygen plant to supply 20 tons of oxygen per day. This oxygen is sufficient for two machines operating full time and one part time. In addition, there are two 50-R, one 60-R and one 40-R machines in use. The benches are 45 ft high and 50 ft holes are generally drilled. JET DRILLING At the onset of jet drilling in the late fall of 1962, two major problems were encountered: 1) freezing due to winter operations; experience and the use of heat at more places, such as the rotary head, has eliminated this,&apos;" and 2) exploding or "popping" drilled holes; this happened frequently (several holes "popping" each day) and was the cause of two lost time accidents. In one instance a hole was being measured with a tape which fell down the hole causing it to "pop." Safety glasses though pulverized saved the wearer&apos;s eyesight. Various methods were then employed to detonate the holes before measuring or loading (dropping lighted rags of fusees down, or sparking across a spark gap). These methods were time consuming and far from completely successful. Consideration was given to the fuel oxygen ratio on the machines and what this would produce in the way of product gases. A fuel oxygen weight ratio of 0.35 which was quite oxygen negative was being used. Theoretically appreciable carbon monoxide would be produced at this fuel oxygen ratio. On the close down procedure of the jet which calls for low oxygen after flame out, oxygen would be left in the hole along with this carbon monoxide. This is an explosive mixture. The fuel oxygen ratio was cut back to stoichiometric

Jan 1, 1967

By R. M. Genevray, M. B. Bever, E. J. Suoninen

THE martensitic transformation in the ß-phase of the Cu-Zn system has been the subject of several investigations. The transformation is known to be reversible and to be affected by stress. Its temperature range has been determined as a function of composition. In the investigation reported here, the effect of tensile stresses on the transformation was investigated quantitatively. Some information was also obtained on the thermoelastic behavior of the martensite formed in the first stages of the transformation. Most of the experiments were done with alloy E of an earlier investigation;&apos; this alloy analyzed 60.49 pct Cu and 39.51 pet Zn by weight. The methods of shaping and heat treatment were also essentially the same as those previously used. The stress was applied to the specimen immersed in a cooling liquid. The transformation was followed by measuring the electrical resistance with a Kelvin bridge and the elongation with a cathetometer. Fig. 1 shows the M, temperature as a function of stress. Resistance and strain measurements gave essentially identical values. The results suggest a roughly linear relation between M. and in the range investigated, up to 12 kg s mm". At higher stresses, plastic deformation begins to interfere seriously with this relationship. The increase of M, with stress is consistent with published work on the effect of stress on the martensitic transformation. The slope of the curve, 4°C per kg mm ", is of the same order of magnitude as the corresponding value calculated for steel.&apos; Fig. 1 also shows the difference, AM, between the temperature of 50 pct transformation on cooling, as measured by changes in length, and that of 50 pct reverse transformation on heating. This difference, which may be considered a measure of the hysteresis, increases with stress; the decrease at highest stresses is probably associated with plastic deformation. Preliminary work using only resistance measurements was done with an alloy containing 60.15 pct Cu and 39.79 pct Zn by weight. The results indicated higher values o-F M, in agreement with the known variation of M. with composition.&apos; The effect of stress on M, (2°C per kg mm-&apos;) was of the same order of magnitude as that shown in Fig. 1 for composition E. An increase in hysteresis with stress was also found. The following experiment was made in order to investigate a partially transformed structure. A specimen of alloy E was cooled to — 85°C under a stress of 4.7 kg mm-&apos;. Under these conditions, the martensitic transformation started but did not go to completion. The stress was then released and the specimen cooled to — 105°C. Fig. 2 shows the measured elongation c. The first change in the slope of the curve indicates the beginning of the transformation under stress. Removing the load at —85°C caused a decrease in length to the value corresponding to the elastic elongation of the parent phase resulting from the applied stress. Hence, the marten-site formed in the first part of the experiment apparently disappears completely and without hysteresis upon the release of the stress. The increase in length on further cooling indicates renewed formation of martensite. These conclusions are consistent with the concept of "thermoelastic" martensite," which has been confirmed by test." Acknowledgments The authors are greatly indebted to Professor M. Cohen for his advice and encouragement. They also thank F. Paxton for assistance. Thanks are due the American Brass Co. which supplied the alloys. References E. Kaminsky and G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1936) 6, p. 984. A. B. Greninger and V. G. Mooradian: Trans. AIME (1938) 128, p. 337. "J. E. Reynolds, Jr. and M. B. Bever: Trans. AIME (1952) 194, p. 1065; Journal of Metals (October 1952). &apos;A. L. Titchener and M. B. Bever: Trai~s. AIME (1954) 200, p. 303; Journal of Metals (February 1954). " 3. A. Kulin, M. Cohen, and B. L. Averbach: Trans. AIME (1952) 194. p. 661; Journal of Metals (June 1952). "J. K. Pate1 and M. Cohen: Acta Metallurgica (1953) 1, p. 531. &apos;C. Crussard: Comptes Rendus (1953) 237, p. 1709. &apos; G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1948) 18, p. 999. G. V. Kurdjumov and L. G. Khandros: Dokl Akad. Nouk. SSSR (1949) 66. p. 211.

Jan 1, 1957