Search Documents

By Raymond B. Ladoo

NONMETALLIC minerals (excluding fuels) arid their primary products produced annual in the United States have a value in excess of one billion dollars, or more than that of the metals, yet the lack of expert knowledge of some of the fundamental technical and economic aspects of this most important and complicated business is astonishing. This paper will deal with the economics of this non- metallic mineral field-the business of making money from producing these minerals. The incentive behind all business activity in a capitalistic economy is to make money-to plan so that each dollar invested in property, plant, equipment, services, and so on will return more than a dollar plus simple interest. Of course, business has social, civic, and national duties and responsibilities, but the fulfillment of these is largely dependent upon financial success.

Jan 1, 1939

By R. W. Raymond

Recent literary labors have led me to the compilation of the following tables and estimates, which may possess interest for my colleagues in the Institute, and which are here submitted without comment.

By Harrison Souder

UNDER the stimulus of steadily in- creasing 'demands of the steel industry at home, and with the supply of available ores from abroad appreciably diminished owing to vigorous rearmament campaigns in Europe, production of Eastern magnetite ores reached an all- time peak in 1937. Although the figures given in the accompanying table are partly estimated (actual figures were available for eleven months only), it appears that 1937 production was nearly 47 per cent higher than that of 1936.

Jan 1, 1938

By ERNEST W. ELLIS

MORE or less contradictory findings as to the most satisfactory feed for concentration tables of the Wilfley type is shown by the diversity of opinion among experimenters. Prof. R. H. Richards,l as a result of his work, favors classification. On the other hand the work of Messrs. Cox, Gibbins, and Porter,' of McGill University, points in general to the desirability of screen-sized feed The ore used was obtained from the West mill of the Bunker Hill and Sullivan Mining and Concentrating Co., Kellogg, Idaho, and consisted of argentiferous galena in a gangue of quartzite and siderite. The natural feed was taken from the launder supplying the Fahrenwald classifier. Classified feed was collected from each of the ten spigots of this same classifier. From the natural feed the screen-sized feed was pre- pared in the laboratory. All three types of table feed were therefore derived from the actual mill circuit of a large plant.

Jan 1, 1926

By George S. Rice

GROUND movement and subsidence is an important matter from several points of view and it is regrettable that more papers have not been written on this subject in the past year. Damage may be done to surface buildings or to the higher workings of a mine, and a study of the subject gives valuable in- formation on hanging-wall or roof control. The latter objective is strikingly shown in a recent paper presented by Jack Spaulding on Oct. 21, 1937, before the Institution of Mining and Metallurgy, of Great Britain, entitled "Theory and Practice of Ground Control in the Kolar Gold Field, India." All may not agree with some of his theories that were deduced from studies of the many violent rock bursts at depths of 5000 to 7000 ft., but the data obtained are of great value. His theories of symmetrical ring stresses and symmetrical domes which are pictured as perfect are rather hard to understand as such uniformity is un- likely in view of the irregularities in the formation due to folds and fractures of various kinds. All will agree in principle with this idea of domal effects, which have been observed in many countries, but they are generally irregular.

Jan 1, 1938

By Oscar A. Glaeser

MINE VENTILATION is an important factor in mine maintenance as well as having direct bearing on labor efficiency. Effective ventilation systems are costly, especially those for the deeper mines, but with intelligent direction the worth of a system is usually greater than its cost. In most mines using mechanical ventilation, and practically all deep mines, it has been found beneficial to equipment, timber, and the ground, to run the fan or fans continuously even though production has been curtailed or entirely suspended. Therefore, economies in ventilation may be overlooked when general cost reductions are necessary. The operating costs of a well-designed ventilation system should be capable of reduction during periods of curtailed or suspended operations. A mine that is ventilated by splits, or that can be sectionized, can reduce its fan-power costs considerably, and provisional divisions can sometimes be made in other mines, in which the air is ordinarily coursed through all the workings, without harmful effects.

Jan 1, 1932

By J. R. Linney

Demand for eastern magnetite in 1948 necessitated practically all eastern magnetite industries to operate on a six-day week, with the result that over 11,000,000 long tons of crude ore were mined, and the shipping products amounted to approximately 5,000,. 000 long tons. Reports indicate that operating on a six-day week and doing maintenance work on the seventh day was satisfactory and resulted in excellent continuity of operation. In the Port Henry district, Republic Steel Corp. once again set new all-time records for the production of crude ore and total shipping product; 1,868,000 long tons of crude ore were mined, 945,000 from the Old Bed mine, 408,500 from the Harmony mine, and 514,500 from the Fisher Hill mine. Of the 969,000 long tons of shipping products, 663,800 long tons were sinter, 181,000 lump ore, and 115,200 con¬centrates.

Jan 1, 1949

By C. J. Bauer

WHEN the pipe lines from the Middle East to the Mediterranean are completed, the Middle East supplies will relieve the strain on Western Hemisphere petroleum resources, part of which are now shipped for Eastern Hemisphere use. A sketch of the world petroleum situation as it appears today and in the immediate future will help in understanding the future place of Middle East oil supplies. Anticipated 1951 world demand is slightly under four billion barrels. To meet this requirement, crude output and refinery runs throughout the world (including Russia) must be increased about two million barrels per day above the average of 1947. This increment, together with pipe lines, tankers, and other facilities, will require in excess of ten billion dollars of new capital in the next four years. We are, therefore, looking forward to the greatest expansion program in the history of the industry.

Jan 1, 1948

It is probably safe to say that, as the economic well-being of the mining industry goes, so goes the fortunes of mineral explorationists. And in 1977 the industry was not well at all. The year-long depression of the copper industry, marked by layoffs, temporary shutdowns, and mine closures, provided an appropriate background for the collapse of the nickel market, passage of a surface mining law that will affect the hard-rock industry in ways that are yet unclear, and the threat of operating under a new set of rules brought on by reform of the Mining Law of 1872.

Jan 5, 1978

By Ian M. Thomson, Robert W. Greene

To move 7 million tons annually from their new inland coal mines at Camp Breckenridge, Ky., TVA selected a transportation package proposed by American Commercial Barge Line. The land portion includes two cable-driven conveyors covering 12.7 miles; a 260,000-ton storage area on a man-made island with a stacking-reclaiming bucket wheel; and a barge-loading system of 5500-tph capacity. The 183mile river portion will utilize three unit-tows with towboats and barges specially designed to carry the maximum tonnage allowed by locks and channel depth. The system has two noteworthy features. The first is a single-flight cable belt conveyor over nine miles long. The other is a high capacity twin belt conveyor using the principal of two separate belts supported in 60° troughing idlers. This conveyor exhibits a high carrying capacity combined with accurate tracking and lack of spillage. A description is given of the mechanical problems and solutions to the design, construction, and operation of the conveyor system which provides the link between the coal mine and the barge loading dock.

Jan 1, 1974

By PHILIP N. MOORE

THE development of the power of the Tennessee River at Muscle Shoals has become a matter of political interest as well as engineering possibility. The controversy over it has been so active that the facts have been obscured, the possibilities exaggerated. Although the members of the American Institute of Mining & Metallurgical Engineers are not generally specialists in hydroelectric development, those who visited Muscle Shoals in October, following the Birmingham meeting of the Institute, were interested, and many of them surprised to learn the actual conditions. These have long been familiar to those who have studied the matter through the reports of the U. S. Engineers on the subject. The approved plan contemplates three dams-No. 1, a low dam close to the City of Florence, planned in the interests of navigation, since the construction of the other dams has rendered impossible the use of the river without it. No. 2-named the Wilson Dam is now under construction. Concerning it political argumentation has waged. No. 3 Dam-much smaller, is planned to be erected several miles above No. 2.

Jan 1, 1925

By E. W. Engle

For several years the Fansteel Products Co. has been engaged in e production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770' C., tungsten 3350' C., and molybdenum 2550" C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum somewhat resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids. The three metals oxidize rapidly when heated at or above a dull red in air. This feature limits their use in many applications where their high melting point and strength make them appear usable. Tungsten and molybdenum, at red heat, are quite inert to hydrogen and nitrogen; while tantalum has a rather remarkable affinity for all the ordinary gases, which results in its becoming embrittled in their presence. This

Jan 1, 1925

By Alfred H. Bell

IN 1945, Illinois produced 75,210,000 bid. of oil, or 4.4 percent of the total for the United States, and ranked sixth in the nation in oil production for the third consecutive year. Production decreased about 3 per cent from that of 1944, when the total Illinois production was 77,413,000 bbl. This is the smallest percentage of decrease in production in the state for any year since a peak was reached in 1940. Daily average production for 1945 was approximately 206,000 bbl. Daily averages by months were as follows:

Jan 1, 1946

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw'1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By William P. Shinn

It is almost exactly seven years since the last previous meeting of the Institute in this city. In a paper on " Pittsburgh, its Resources and Sorroundings," read at that meeting, I showed that Allegheny County had produced in 1878, " one-twelfth of all the pig-iron,.... two-ninths of all the rolled iron (except rails), over one-eighth of all the Bessemer and open-hearth steel, two-thirds of all the crucible blister and puddled steel, one-fourth of all the glass, one-eighth of all the coal, and one-sixth of all the pig-lead produced in the United States;" and the object of this paper is to show that, great as the record then was, it has been greatly surpassed since.* Population. In my former paper I expressed the opinion that the census of 1880 would show the population of Allegheny County to be in excess of 300,000. The census report made it 355,869. The following shows the growth of the county in population from 1790 to 1880: 1790,...........10,309 1800,........... 15,087 1810,...........25,317 1820,...........34,921 1830,...........50,552 1840.............81,235 1850............138,290 1860............178,881 1870,...........262,204 1880,...........355,869 This makes Allegheny County, in 1880, rank sixth in population of the counties of the United States, whereas in 1870 its rank was ninth. The population of Pittsburgh in 1880 was 156,359, being twelfth

Jan 1, 1886

By John A. Mathews

D R. CHARLES W. ELIOT, the great educator and philosopher-he of the five-foot book shelf-recently gave expression to a thought I had long been cherishing as a private opinion, when he said: "It is obvious that standardization has become a dangerous adversary of progress in both education and industry." This idea must have been more widespread than either of us knew, for some five years ago a writer of verse for one of the comic papers dealt with it at great length. I will quote only a few of his stanzas to illustrate his understanding of "A Standardized Existence" : A visitor at large, I stand Beneath a standard sky- Where everything is standardized To please the standard eye. Each tree is of a standard height, Each building is the same; Each man is uniform in height, And has a standard name. Above there is a standard star Beside a standard cloud, And a standard weather here prevails To please a standard crowd. With standard joy, and standard gain, The standard people live; And if there is one bit of pain T?is such as standards give.

Jan 1, 1926

By KING HAMILTON GRAYSON

IRON and steel were the only basic industries in the Soviet Republic in 1928 that lagged behind the pre-war production on a comparative basis. This was due to the almost complete obliteration of all industrial units manufacturing iron and steel products during the Revolution, which resulted in the production of 1921 being only 4 per cent of that of 1913. By the end of 1927 the production of pig iron had reached a point equal to 70.5, per cent of 1913; steel was 84 per cent ; and rolled iron was 78 per cent. According to the. planned program of the Supreme Economic Council, the pre-war level of the iron and steel industry was to have been reached and exceeded during 1929-30. The production of the entire period from 1917 to 1928 in comparison with 1913, is shown in the following table

Jan 1, 1929

By M. B. Kahle, A. D. Pernichele

Four types of slope failures in waste dumps are recognized debris flow, foundation failure, edge slump, and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is the most dangerous because of its explosive mode of failure and lack of forewarning. The December 1969 failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicates that the impounded water was perched on a zonal accumulation of jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1972

By E. W. Engle

Fox several years the Fansteel Products Co. has been engaged in the production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770° C., tungsten 3350° C., and molybdenum 2550° C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum some¬what resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids.

Jan 3, 1925