Search Documents

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By David Donoghue

Efforts made in the year 1930 and in previous years restricted production in most of the fields of Texas to a point that was satisfactory, at the beginning of 1931, to the majority of producers and buyers. In the Panhandle, North Texas and West Central Texas districts, a few operators with refinery affiliations or contracts either ignored, or by virtue of injunction suits, did not comply with the Railroad Commission's orders, and there was some oil sold at less than posted prices, which, with the Oklahoma City difficulties, caused the first general price reduction. More could have been done perhaps to help the situation on the Gulf Coast and in the Laredo district, but natural advantages are not readily surrendered. East Texas Proration troubles in 1930 were insignificant when compared with those of 1931. In January, 1931, efforts were begun to convince the producers and citizens of East Texas of the necessity of curtailment. Opposition quickly developed and meetings were held in the towns of the region and proration denounced vigorously. Notwithstanding a strenuous campaign for additional legislation waged by many producers, the regular session of the State Legislature refused to strengthen the conservation laws and passed only the Marginal Well Bill, designed to prevent the Commission from prorating small wells. The Railroad Commission held a heated hearing on East Texas in the latter part of March. During April the Commission issued three orders based on the Yates plan for the proration of the East Texas field. Each succeeding order raised the allowable for the field. In June the opposition held more mass meetings at which a plan based on acreage was endorsed. Apparently on the theory that any plan was better than none, the Commission issued an order on July 2 embodying some of the features of the proposed plan, limiting production to 250,000 bbl. per day, and dividing the producing area into 20-acre units participating equally in the outlet. Owing to the bringing in of many wells and the many violators of the Commission's orders, production increased to such an extent that prices went as low as 5c per barrel.

Jan 1, 1932

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company's Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

By P. He

Abstract This paper introduces tested results of rock-socketed pile in Nanjing, Wuhan and Chongqing. From a force- transfer model, a distribution of axial force for pile-body and inlaid resistance for rock-socketed pile was deduced. Comparing the results of test and calculation, it shows that the calculation result coincide with the test result. Keywords rock-socketed pile, load transfer, inlaid resistance, end resistance. Zusammenfassung: dieser text legt eine kuyze Einfuehyung ueber die Erfolge wissenschaftlicher Forschungsarbeit in bezug auf die Grundprinzipien der Mechanik von Belastungsuebermittlung der Einlegesteinpfeilers der Durch Benutzung von Ausgleich/Balance der inneren Kraft und Deformationskoordinierung wird das mechanische Modell der Belastungsuebermittlung des Einlegesteinpfeilers aufgestellt. Vom lebendigen Beispiel wird dia Wellenkraft des Steinpfeilera und die Verteilungskurve Einlegebfestigungskraft ausgelegt, man hat diess bereits mit der tatsaechlichen genessenen Kurve verglichen. Schluesselwoerter: Einlegesteinpfeilers, Belastungsuebermittlung, Einlegebfestigungskraft, Seitenwiderstand. Résumé - Le présent article décrit de façon succincte des résultats de la recherche sur le mécanisme du transfert de chargement du pieu d’ancrage au massif. Une modèle dynamique du transfert de chargement du pieu d’ancrage au massif est ainsi établie avec l’application des conditions de l’équilibre de contraintes internes et de coordination de la déformation. L’expérimentation sur des exemples réels a permis de mettre à jour des courbes de distribution de la force axiale du corps du pieu et de la force d’ancrage avec comparaison aux courbes effectivement mesurées in situ. Mots clés - Pieu d’ancrage au massif, Transfert de chargement, Force d’ancrage, Résistance à la pointe

Jan 1, 2003

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.' Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923

By W. F. Boericke

The character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed (a flat generally well-defined clay seam a few inches thick) which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.' Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 1, 1923

By Howard Lee

I. GEOLOGY AND ORE OCCURRENCE IN central Colorado is a great belt of intrusive porphyry nearly 100 miles long (160 km.), extending from the Clear Creek district on the north to Aspen on the south, which includes many of the well known mining camps of the State. Near the southern end of this belt, at Leadville, the occurrence of these intrusives is most marked, resulting in intensive mineralization and the formation of a great variety of large orebodies. During the past 40 years, Leadville has been a steady producer of gold, silver, lead, zinc, manganese, iron, and bismuth, in the forms of sulfid, carbonate and oxide ores. It is the purpose of this paper to discuss pyrite alone, which, under present economic conditions, is valuable chiefly for its sulphur contents. The ore-bearing formation of the Leadville district consists of two beds of limestone separated by a layer of quartzite. The upper limestone is carbonaceous, and is known locally as the blue limestone. It varies in thickness from 50 to 300 ft. (15 to 91 m.). The lower limestone is Silurian, known locally as white limestone, and is about the same thickness as the upper bed. Underneath the Silurian limestone is a layer of Cambrian quartzite front 100 to 250 ft. (30 to 76 in.) thick resting on Archean granite, which forms the limit of ore deposition. As a rule, there is a sheet of white porphyry above the upper, or blue limestone; a sheet of gray porphyry is associated with the blue limestone, either in or below it, but the porphyries are not so regular as the quartzites and limestones and are not always found in their expected positions. Throughout the district there is an elaborate system of faults and intrusive porphyry dikes, which have all important bearing on ore deposits. The writer has seen two or three orebodies which were not closely associated with either a fault or a porphyry dike, but if the minor fractures and water courses are considered as part of the fault system it is safe to say that all orebodies are directly traceable to one or both of these causes.

Jan 8, 1918

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

By L. O. Howard

The practice of using acid-lined converters at the plant of the Old Dominion, Copper Mining & Smelting Co. was discontinued early in January, 1913, and replaced by basic-lined converters. The new equipment consists of one electrically operated 12-ft. upright converter stand and two basic-lined shells for same. These shells are provided with twenty-four 1 1/4-in. tuyeres. The mouths are 5 ft. in diameter. Owing to the fact that there is no bedding system or other large storage capacity between the mine and the smelter, the furnaces must handle as fast as produced ore and concentrates, which may vary considerably from day to day, both in tonnage and copper content. Consequently the converter is often crowded to its utmost capacity by the frequent fluctuations in the daily matte supply. From the foregoing, it will be seen that in no way can the 'converter be favored by running light charges or by transferring to it from other stands in operation. Neither can it regularly be allowed to cool between blows, and only occasionally can it be run at as low a temperature as might be wished. No copper precipitate or other foreign material high in copper is available to help out the tonnage. Repairs and alterations or the removal of defective tuyeres must wait until such time as a slight falling off in.the matte supply allows the converting operations to ease up. These variable conditions all combine to interfere with the systematic operating of the converter. The first 12-ft. shell was blown in on Jan. 6, 1913, and ran until June 27, 1913, when it was removed to patch the brick. A record of operations covering this period follows: Shell No. 1. First Campaign, Jan. 6,to June 27, 1913 Commenced blowing............................Jan. 6, 1913. Taken off stand for patching.....................June 27, 1913. Total blowing time..........................2,689 hr. 40 min. Total number of, blows made.............................. 664 Average time of blow............................ 4 hr. 3 min. Tons matte charged.................................. 18,157 Average copper content of matte................ 43.9 per cent. Average time blowing one ton. copper................ 22.5 min. Total copper made............................... 7,250 tons

Jan 1, 1915

By Fred T. Greene

Most of the recent discussion of the mineral land law published in the Transactions is in the abstract—an exception being Mr. Goodale's paper, The Apex Law in the Drumlummon Controversyll which illustrates in concrete instances many of the practical disadvantages of what Dr. Raymond has called "The Law of the Apex." The present paper, it is hoped, may serve a similar purpose, emphasizing the necessity for a change in our mining laws, and bringing home to mining engineers some of the defects and dangers of our present code. There are many storm centers of "apex litigation" in the Rocky Mountains; and not the 1east. of them is the Wardner camp, where such litigation has been almost continuous since 1892, and the end is not yet. In their decisions, the courts have accepted the claims of the litigants that the "Wardner vein" is a broad zone varying from 250 to 500 ft. in width at the surface. This is the simplest theory which could have been advanced, and probably decreased, rather than augmented, the number of contests; in fact, every one of the claim owners seemed to feel that the greatest advantage would accrue to him if this theory were adhered to. The dominant structural feature of the Wardner vein is a persistent fault, striking N. 40' W., dipping about 40" to the southwest and called the "Wardner foot wall." Fig. 1 is a composite of two adjacent cross-sections of the vein and is a fair representation of the relative size and shape of the orebodies and their relation to the "Wardner foot wall." The country rock is a comparatively thin-bedded sericitic quartzite which has an average strike of N. 80" W. and dips at high angles to the north and south. The movement on the Wardner foot wall is apparently normal, and there has been more or less brecciation on either side of it; but as the moving mass was that above the foot wall, the brecciation has been more complete on that side, and has extended farther from the plane of movement. Many minor faults, generally of insignificant extent, resulted from the movement along the Wardner foot wall. Most of these were

Jan 1, 1916

By Gift Makusha, Dave Minney

Anglo Coal South Africa mines coal for both the domestic and export market using open cast and strip mining methods. To establish a mine, a process is set in place to gather ever increasing amounts of geological and metallurgical data to confirm a proven reserve. Increasingly, geotechnical data are also included in this process to confirm that reserve is easily and safely mineable. The mine design process is an iterative one using a combination of numerical modelling and empirical data to arrive at a mining layout that is both, practical, productive and safe. In South Africa it is a legal requirement to compile a code of practice to combat rock fall and slope instability accidents and these have to be revised annually, reinforcing the iterative process of continual improvement. To ensure best practise occurs, all Anglo Coal operations are subjected to annual 2nd party audits and ad hoc 3rd party audit by independent consultants. This paper attempts to explain the process described above in a concise, but understandable manner. 1.0 GEOLOGICAL SETTING The Ecca sediments date from the Permian period and the coal deposits were formed in glaciated valleys on a basement of Dolomite, Ryolite or Granophyre rock types. The sediments overlying the coal deposits are typically flat lying and multiple bedded. The sediments consist of mudstones, shales and sandstones and are generally capable of forming stable highwalls given the time that they must stand up for. Anglo Coal extracts coal from the Witbank, Highveld and Vereeniging coalfields. The Witbank coalfields contain five seams numbered from the base upwards, 1 to 5 Seam; Highveld coalfield the 2 and 4 Seam and the Vereening area the seams are described as Top, Middle and Bottom seams. Coal deposited over the basement Dolomite formation display very erratic dips, as contemporaneous subsidence occurred in some instances over sinkholes that were forming, resulting in local thickening of the coal deposit and resulting in strata that dips toward the centre of the sinkhole.

Jan 1, 2006

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

By Lloyd Jones

THE strip industry made rapid strides in regard to both width and gage until about 1922, when the maximum width was about 20 in. In the hot mills, strips of thin gages in wide widths could be pro-duced, but only at a sacrifice of length of coil, con-siderable increase in power, and decreased tonnage out-put on the min. Hot mills, like the Bray sheet mill and the modern strip and skelp mills, demonstrated that . wider strip could readily be rolled, if such a product was desired. The strip manufacturers were really limited in width, not by the hot strip, but by the cold rolling of wide strip. This factor was roll pressure. The diameter of rolls increased as the width of strip increased. For cold rolling strip 20 in. wide, cold rolls were approximately 20 in. diameter. As the rolls became larger, the arc of contact between the rolls and the strip increased approximately, according to the formula, b=\/Rd where b = the width of contact R = roll radius d = total reduction Now the crushing strength of cold steel of low carbon varies from 70,000 to 100,000 lb. per sq. in. With each succeeding pass the crushing strength increases and may approach 250,000 lb., according to the total reduction. The total reduction in cold rolling of low-carbon steel will range from 40 to 70 per cent of the original thickness, usually in about three or four passes. On this basis, assuming a reduction of 20 per cent in one pass, the crushing strength of steel assumed at 120,000 lb., we have a total pressure between rolls, which (assuming that the rolls do not deform) equals: Roll Strip Strip Diameter, Width, Thickness, In. In. In. Pounds 10 10 0.100 380,000 20 20 0.100 1,080,000 30 36 0.100 2,375,000 42 50 0.100 3,900,000 These figures are approximate, but you will note that in increasing the width five times, or 50 in., the total pressure between the rolls increased approximately ten times. In other words, the pressure per inch of width increased from 38,000 to 78,000 lb. for the same per-centage of reduction.

Jan 3, 1928

By George A. Macready

Trinidad, British West Indies, is an island near the north coast of South America, situated between latitudes 10" and 11" N., and opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,-250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi. (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1'Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 31/2 mi. south of Pitch Lake on Lot Three of Morne 1'Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 1, 1921

By P Jackson, J Rea, M D. Goodz

The Morning Star Gold Mine has operated over a 101-year period, producing gold from narrow quartz veins and sulfide stockworks hosted mainly within a dioritic-gabbroic dyke. The deposit has been developed over a vertical depth of 980 m with drilling extending the vertical depth to greater than 1200 m. Currently there is a total Inferred Resource of 4.6 million tonnes at a grade of 6 g/t for 910 000 ounces of contained gold resources, which comprises an underground project and a surface project. Significant variation exists between the grade of drill core intersections and that observed in face sampling and subsequent production reconciliation (250 - 650 per cent). Studies were carried out on ten major production reefs, where the grades of drill intercepts were compared with face samples collected during development and mining. The implications of this study have been used as justification to assign production or stope/development grades where applicable to resources that are direct extensions of the historical development headings. Grade assignment and its impact on sensitivity for gold resources are detailed and show a 40 per cent variation in the gold resource, depending upon whether a production or calculated stope grade is used in grade assignment for the major reef deposits. Recent diamond drilling has intersected approximately 40 new gold bearing quartz reefs and sulfide zones that contain all the key mineralogical and structural indicators, and traditional large variations in gold grades similar to the historical major production zones. The implications of grade factoring and grade assignment are the greatest challenges confronting the resource estimation team in defining grade for these new zones. Grade assignment is seen as a method of balancing known historical production observations with the irregular grade distribution inferred from drill core assay results. Ongoing mine development and bulk sampling works are planned to validate the grade assignment process. The first stage of this process is the trial mining of the newly discovered Maxwell Reef (MR). The stope drawpoints were completed in August 2008 and the MRS1 stope is scheduled for completion in September. The stope reconciliation results will be presented at the October 2008 conference.

Jan 1, 2008

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006