Search Documents

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By A S. Derrington

This paper describes a hybrid ventilation system, which uses secondary fans that also act as de-facto primary fans to extract fresh airflow from the mine intake raise system. Also discussed are the associated problems such as uncontrolled recirculation, inadequate decline airflow, fire safety issues, prolonged blast fume clearance times, high air temperatures in main access routes, neutralisation of mine air cooling by heat from secondary distribution fans, increased ventilation system complexity, reduced flexibility and high pressure differentials (which cause safety issues with personnel access and reduce secondary ventilation system performance).Practical suggestions are provided on options to avoid these problems listed.CITATION:Derrington, A S, 2013. A critique of the push-pull hybrid ventilation system, in Proceedings The Australian Mine Ventilation Conference , pp 73-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By P Holtham, K Duffy, W Valery, A Jankovic

As high grade ore deposits are depleted, remaining deposits are generally lower grade and require the mining and processing of larger volumes of material per tonne of product. These low grade deposits often contain a large proportion of barren gangue. Pre-concentration aims to remove this barren material at as coarse a particle size and as early in the process as possible. This has the potential to reduce processing costs, energy and water consumption, increase production and improve resource utilisation.There are several technologies that may be applicable for pre-concentration. This paper looks specifically at bulk ore sorting and how it can be integrated into existing or new mining operations to improve profitability and reduce environmental impact. Bulk ore sorting is the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor measurement. It may be used to increase the production rate through fixed plant capacity, or increase production and/or reduce the size of downstream processing equipment in Greenfield operations. Marginal ore sub-economic reserves may be upgraded, making them economic to treat and improving the resource utilization. Bulk ore sorting could also be used to reduce dilution and ore loss in mining operations by improving grade control, or to separate ore types to treat via different process routes. Various applications of bulk ore sorting are discussed in this paper, and three cases are investigated considering the impact on the overall operation and the associated benefits.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Integrating bulk ore sorting into a mining operation to maximise profitability, in Proceedings MetPlant 2015, pp 273–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By D. J. Fray, F. Tailoka

Microporous ceramic tubes (15 micrometre pore diameter) and PVC membranes (10 micrometre diameter) have been used as spargers in the electrowinning of copper from concentrated and dilute chloride electrolytes. At a current density of 600 A/m2 and a nitrogen gas sparging flow rate (at NTP) of 1.53 cm3/s per unit electrode length, it was possible to electrowin planar rather than powdery deposits with copper concentrations as low as 0.157 M. To obtain a planar deposit at higher concentrations of cupric chloride the most realistic optimum current density appears to be between 1 000 and 1 500 A/m2.

Jan 4, 1993

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By C. S. Parsons

Custom milling-plants have been operated successfully for a great many years on this continent. One of the outstanding examples in the United States is the Golden Cycle mill at Colorado Springs, which mills the gold-telluride ores from the Cripple Creek district. In eastern Canada, the Northern Custom Concentrators, Limited, at Cobalt, successfully treated the cobalt-silver ores of that area for a number of years. Flotation plants have entered the custom field in the past few years. The building of flotation concentrators to treat ores on a custom basis indicates the advance which has been made in flotation. In fact, three years ago it was considered almost impossible to treat successfully a mixture of miscellaneous ores by flotation. The methods used at that time were considered so delicate that any change, even in a single ore, would usually result in decreasing the effectiveness of the separation. Today we find four large custom flotation plants in the United States and one in Canada for treating complex lead-zinc ores from many different localities. The advent of these mills was brought about by the serious problem confronting the lead-smelting plants due to increasing amounts of zinc in the ores presented for treatment. It was necessary to penalize the mines shipping high-zinc ores. The penalty is justified, because high zinc in the lead blast-furnace charge not only decreases the tonnage of the furnace but increases the amount of flux necessary, as well as increasing the metal loss in the slag. It has been estimated that in the Salt Lake valley alone, 75,000,000 pounds of zinc was lost in the slag-dumps from the operations of three large lead blast-furnace plants. It has also been estimated that $150,000 worth of additional flux was required to slag this zinc. It was to avoid at least a part of this wste and to help maintain an ore supply that custom flotation concentrators were built by the smelters.

Jan 1, 1928

By H. C. Rickaby

The Bannockburn gold area covers the four townships of Bannockburn, Argyle, Hincks, and Montrose, lying in the western part of the Matachewan district of Ontario (see Figure 1). The geology of these four town-ships was studied by H. C. Cooke of the Geological Survey, in 1917-18, and is shown in his map of the district. In the fall of 1930, a rich gold-bearing quartz vein was discovered in the northwest part of Bannockburn by B. S. Ashley. A prospecting rush followed the discovery; many claims were staked in the Bannockburn area, and, during the summer of 1931, a considerable amount of prospecting was done.

Jan 1, 1932

By S. E. Malouf, R. Hinse

"The Mineral possibilities of the Chibougamau area were first recognized by Richardson in 1870 and Low in 1885, both of the Geological Survey of Canada. The first record of interest by the Quebec Bureau of Mines is in 1904, when J. Obalski reported on the discovery of copper and asbestos by Peter McKenzie in the previous year. Reports of 1906 and 1907 covered the McKenzie Gold Mine find and other deposits. In 1908 Prof. Dulieux described the quartz vein on Merrill Island and the mineralized zone on the near-by mainland. In 1910 the Chibougamau Railway Commission, though commenting favourably on the possibilities of the area, concluded that a railway was not then warranted.In spite of this, prospecting in the district continued. The main Campbell Chibougamau deposit, the Blake showing on Merrill Island in Dore Lake, was found in 1920, and other discoveries were made soon after. Between 1927 the work of Mawdsley, Retty, and Norman tor the Geological Survey and the Quebec Bureau of Mines stimulated further interest. In 1934 Consolidated Chibougamau Goldfields Ltd., a subsidiary of Consolidated Mining and Smelting Co. of Canada Ltd., acquired the Merrill Island and Cedar Bay holdings of Chibougamau Prospectors Ltd. They embarked on an aggressive campaign, directed essentially at the gold quartz veins at Cedar Bay. Exploration there included a 522-foot shaft, 4,732 feet of drifts and crosscuts, and about 34,000 feet of surface and underground diamond drilling. Thirteen holes were also drilled on the replacement sulphide lens at Merrill Island. Operations were suspended in 1936, as the occurrence was too low grade for development at the existing metal prices and under difficult operating conditions.The completion of the Quebec Bureau of Mines highway from St. Felicien to Chibougamau in 1950 was followed by a project of detailed geological mapping by the Bureau. It also encouraged Campbell Chibou-gamau Mines to acquire the assets of Consolidated Chibougamau Gold-fields and commence a program of surface exploration. Between August 1950 and April 1951, 41,183 feet of diamond drilling was done on the Cedar Bay and Merrill Island holdings. The Blake showing off the west shore of Merrill Island developed at depth into a major orebody. A lease was obtained on adjacent ground from Merrill Island Corporation, and underground work commenced in November 1951. Development at Merrill Island to June 1st, 1955, included a four-compartment shaft to 1,225 feet, with 8 levels at 150-foot intervals, 5,317 feet of raises, 16,709 feet of drifts and crosscuts, 52,514 feet of surface and 96,593 feet of underground diamond drilling."

Jan 1, 1949

By Paul W. Jeran

Subsidence was monitored by the U.S. Bureau of Mines over the ends of longwall panels operating in the Pittsburgh, Kittanning, and No. 2 Gas Coalbeds of the northern Appalachian Coal Basin. The final subsidence over the finishing ends of three panels in the Pittsburgh Coalbed are compared with the subsidence measured over the rib at these panels. The characteristics of subsidence are different. At Mine A, data over the start of a longwall panel shows similar characteristics to the subsidence measured over the rib. Subsidence over the fmishing ends of panels in the Kittanning and No.2 Gas Coalbeds are also different from the subsidence over the rib. The use of a subsidence prediction model based on data gathered over the rib of a panel will not yield accurate results if it is applied to the finishing end of a longwall panel. Acceptable results may be obtained along the centerline over the starting end of a panel.

Jan 1, 1991

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"In natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the content of MoO3 varies from 2% to 10%. As a result, the flotability of seyrigite (scheelite with molybdenum) turns to be weaker. One seyrigite mine, which has been built for 3 years,still could not produce qualified seyrigite concentrate due to the weak flotability of seyrigite (Mo-bearing scheelite) in raw ore. In our experimental research, through adopting new seyrigite collector TA-3 and advanced mineral processing technology, the seyrigite concentrate with a grade of 65.62% WO3 at a recovery of 87.47% was obtained for the raw ore containing 0.19% WO3 and 0.074% Mo. By applying the new technical achievement, for the raw ore containing 0.272% WO3, the seyrigite concentrate assaying 68.03% WO3 with a recovery of 77.56% was obtained in industrial production.INTRODUCTIONIn natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the scheelite is changed to be seyrigite (Ca[(W,Mo)O4]) (Ma, Bian, & Wang, 2013). The content of MoO3 in seyrigite varies from 2% to 10% usually, the content of MoO3 in some of the seyrigite even reaches 34%. The flotability of seyrigite is weak (Zhang, 2007), and the seyrigite is difficult to be recovered by flotation with common collectors and regulators. One scheelite mine in Anhui China, which is a skarn type seyrigite mine, has not produced qualified concentrate yet since 3 years it has been built due to the limit of beneficiation technology. Therefore, it is necessary to conduct research on the collectors with high efficiency and developing advanced processing flow for this kind of ore."

Jan 1, 2016

By H. L. Bourne

The sand dunes which line the east shore of Lake Michigan resulted after the last, or Wisconsin, glacial period in Michigan. Melt-water streams carried vast quantities of glacial debris to the near shore areas of predecessors to Lake Michigan. As the lake levels receded, these vast quantities of sand were exposed to the prevailing westerly winds, which was the last major process that acted upon the sand and resulted in the formation of the dunes. 1 These dunes are one of the significant natural resources within the state. Michigan dune sands supply about 90% of the foundry sand used in the automotive industry, and 40% of the foundry sand used 2 for all purposes within the United States. The deposits owe their importance to the following factors: grain size distribution, grain shape, mineral composition and location with respect to the foundry sand market. In spite of their economic significance these I deposits are in jeopardy through legislative preemption.

Jan 1, 1975

By R. W. Bartlett

The extensive central Idaho black sand placer deposits are a potential source of rare earth elements, particularly the heavy rare earth elements that are not prevalent in commercial bastnasite deposits. These placers derive from the Idaho batholith. The geology, occurrence, and extent of these deposits are reviewed and the diverse mineral assemblages and complex mineral chemical compositions of these sands are described. Niobium, yttrium and thorium are also present in significant concentrations. The results of prior mining practice, including concentration and separation of the heavy minerals are reviewed. Technical approaches to extraction of rare earths from Idaho black sand concentrates are discussed.

Jan 1, 1992

By Luis Alberto Sfalsin Passos

Com o passar dos anos observa-se uma mudança nas características mineralógicas dos minérios de ferro lavrados nas novas minas da Samarco Mineração SA. De acordo com levantamentos podem ser constatadas mudanças nos percentuais da hematita porosa, hematita especular e da goethita na constituição do concentrado de minério de ferro. Pode-se verificar uma tendência de aumento do percentual de goethita bem como do PPC (perda por calcinação) característica intrínseca ao minério. Estes fatos implicam em uma maior dificuldade da concentração em garantir a qualidade da polpa de minério bombeada para as usinas de pelotização, visto que fatores como a granulometria do minério (partículas menores que 325#) e a superfície específica são afetadas pela mineralogia. Por consequência, há uma maior dificuldade no processo de filtragem para obtenção do pellet feed com a faixa de umidade necessária para o processo de pelotamento e queima. De outra forma, o aumento do PPC dificulta o processo de secagem das pelotas no forno de pelotização, exigindo um maior aporte térmico para retirada da água residual contida nos cristais que não evaporam a 100°C. Todos estes fatores contribuem para a qualidade da pelota queimada, interferindo na sua resistência física como compressão a frio e tamboramento. Esta pesquisa tem como objetivo apontar as variáveis que influenciam significativamente o tamboramento, para propor ações que melhorem o controle do processo produtivo de forma a buscar o ponto de equilíbrio entre qualidade e produção.

Aug 16, 2017

By Hongxu Li, Zhaobo Liu, Zihan Zhao

A completely new process of selectively recovering Sc3+ without impurity of Fe3+ from Bayer red mud was developed. Prior to water leaching process, red mud needs to be digested and sulfated at a low temperature and subsequently roasted at a higher temperature for a period of time. During the roasting process, the products such as SO2, SO3 and H2SO4 molecules of thermal decomposition of sulfites including NaFe(SO4)2 and NaAl(SO4)2 could be recycled and reused as the raw materials of sulphuric acid. The leaching results indicate that roasting temperature and roasting time are the main constraint on selective leaching performance of scandium. As the sulfated red mud sample is roasted at 750 degrees C for 40 min and subjected to water leaching at 50 degrees C for 30 min, 53.0 wt% Sc3+, <1.0 wt% Fe3+, <0.3 wt% Si4+ and ~8.9 wt% Al3+ could be leaching out. Of note, the solid-liquid separation process is quite easy to be carried out.

Mar 1, 2017

By Robert L. Schmidt

The support of underground openings by water is a natural phenomenon. Surface sinkholes, such as those that occur with some frequency in Florida, are attributed to a lowering of the water table resulting in the draining of existing limestone cavities. This withdraw the natural support and causes the surface subsidence. The role of water as a ground support medium was demonstrated in a mining situation during Bureau of Mines research on borehole mining of phosphate in St. Johns County, Florida. The borehole mining tool (BHT) incorporates a water jet nozzle and slurry eduotor in a single down- hole tool. The tool is lowered through a bore- hole into the ore zone, and an underground cavity is eroded by the motion of the water jet with the slurry simultaneously pumped to the surface. In addition to phosphate, the system has been successfully used in coal, oil sands, and uranium. The Florida phosphate ore is located at a depth of approximately 250 ft in strata that produce high water inflows. These factors preclude extraction by conventional methods, either surface or underground, but they present an ideal setting for borehole mining. Previous borehole mining research had led the researchers to believe that the system would only be effective in a void cavity, that is, a cavity where the water level is maintained below the water jet nozzle, so that the water does not impede the action of the let. It was soon discovered, however, that the void cavity presented ground control problems. The overlying strata started to cave soon after the support provided by the water was removed. This was an unacceptable situation as it adulterated the ore and threatened surface subsidence. Further tests wherein the size of the cavity -as reduced by cutting only a 30° arc also resulted in caving. A new concept, air shielding, was then introduced and tested. With this system, the water jet cutter was surrounded with a shroud of compressed air, thereby gaining the advantages of cutting in air while retaining the roof support afforded by a water-filled cavity. This arrangement proved to be highly successful. The air-shrouded jet was able to cut a cavity radius of about 18 ft, and the system production was 35 tph, which compared favorably to the production previously attained in void cavities. The borehole phosphate experience proves the efficacy of remote mining in a water filled opening. This system neutralises the hazards of heavy ground, and may, as in the case of the phosphate deposits, be the only viable alternative. It opens up the possibility of application in a wide range of deposits not only those amenable to hydraulic mining. Remote mechanical System might be developed using present robotics technology and then operated in water-filled openings.

Jan 1, 1986

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0&apos; the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.&apos; Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to &apos;solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.&apos; It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945