Search Documents

By Bob Munz, Ry Stone

To facilitate the installation of the longwall equipment for each extraction panel, West Elk mine develops set-up room roadways that are between 26.5 and 30.5 feet wide. Historically at the mine, the set-up room roadways have been driven in a single 20-foot-wide pass, then incrementally widened to the required width during installation of the longwall shields. The first pass roof is supported with a generic roof support plan consisting of partially encapsulated roof bolts and point-anchored cables. This ground support plan was utilized regardless of the geotechnical conditions encountered in the roadways or consideration of the required stand-up time of the roadway before the longwall shields were installed. This "blanket" approach tends to result in over-conservative or inappropriate roof support designs, particularly in changing geotechnical environments. Guided by the desire to optimize the ground support plans and increase mining efficiency for future set-up rooms, the West Elk mine and Agapito Associates, Inc. have developed and implemented a strata management program. Strata management, as a formal and structured process, allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a con- trolled manner (Thomas 2007). To arrive at adequate site-specific ground support plans for the set-up rooms at the mine, several struc- tured processes were utilized. Firstly, the geotechnical environment was characterized by examining the roof lithology and geomechanical properties from nearby rock core obtained from exploration boreholes. To increase both mining efficiency and continuity, and to achieve longer stand-up times before the longwall shields are installed, a multi-pass approach was implemented into the design. During mining, the geotechnical conditions of the roadway are mapped, and the roof is strategically surveyed with a borescope. This process was used to ensure that the encountered ground behavior was in alignment with the design standards used for the roof support design. To support this process with measured data, roof extensometers were strategically installed throughout the roadway. This data was used to monitor the magnitude of roof displacement at various horizons and record displacement rates up until the longwall shields were installed. Lastly, a Trigger Action Response Plan (TARP) was used during mining to cater for any unforeseen changes in ground conditions that would warrant additional con- trols such as increased monitoring or the installation of additional ground support. This paper presents two case histories at the mine where the above strata management approach was implemented to arrive at a site-specific ground support plan. The main changes to the mine's ground control plan included a multi-pass mining approach, the utilization of fully encapsulated roof bolts, and the transition to a stiffer roof support system. The geotechnical mapping, the roof borescope results, and the roof extensometer data will be presented to demonstrate the effectiveness of the ground support system up until the longwall shields were installed in both presented cases.

Jun 25, 2024

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By Personal técnico de la concentradora

El objetivo del trabajo es señalar los beneficios obtenidos en la planta Sacracancha a través de la instalación de un sistema económico de remolienda de baja inversión, readaptando sus molinos de bolas originales. Para ello, se requiere de una liberación adecuada de partículas para cada tipo de mineral y así obtener los resultados metalúrgicos satisfactorios en las plantas de flotación. La aplicación de este sistema en la concentradora de Sacracancha, la resolvió el problema de dureza de los minerales, encontrándose que la inversión fue pequeña, comparado con el costo de instalación de un molino de barras. Asimismo este circuito de molienda es elástico, dado que puede trabajar con molienda en una sola etapa, remolienda parcial, o remolienda total.

Aug 20, 1963

By Andrea Lisjak

The mechanical behaviour of Opalinus Clay, an indurated over-consolidated argillaceous rock, is heavily influenced by the presence of preferably oriented bedding planes. The objective of this study is to illustrate a new modeling approach aimed at capturing the bedding-induced anisotropy of Opalinus Clay as observed in the laboratory and in situ. The combined finite-discrete element method (FEM/DEM) is employed as the main simulation tool. FEM/DEM is a numerical method that models material damage processes by explicitly considering fracture nucleation and propagation. A transversely isotropic elastic constitutive law is used to account for different elastic property values in the direction parallel and perpendicular to the layering, while strength anisotropy is captured using a directional cohesive fracture model. Quantitative calibration and validation of the model is based on laboratory results of indirect tensile tests and uniaxial compression tests. Emergent strength and deformation properties, together with the simulated damage mechanisms, are shown to be in good agreement with experimental observations. Preliminary results relative to the analysis of a circular tunnel show that the approach is able to reproduce the main Excavation Damaged Zone (EDZ) formation mechanisms as observed in the field.

Jun 1, 2012

By Nirmal Weerasekara, Malcolm Powell, Mohsen Yahyaei

"The conditions under which rocks become superficially damaged during the grinding process are not well understood. The main purpose of the work presented here is to understand how superficial breakage occurs under incremental low-energy impacts. To enable this study a series of abrasion tests with multi-size pilot mills have been performed. Outcomes of numerical simulation corresponding to each test were examined to investigate the experimental results. Abrasion tests have been conducted using three grinding mill sizes (i.e. 1.8, 1.2, and 0.8 m). Two types of ore were used to investigate different hardness strengths. To ensure abrasion was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. The relationship between the Fractional mass loss rate and particle size was investigated by randomly collecting seven tracer particles from sizes -73+63, -53+45, and -37.5+31.5 mm. It was evident from the results that the Fractional mass loss rate of angular particles declines as the particle size increases whereas the Fractional mass loss rate decreases from fine to coarse in rounded particles. Results of Discrete Element Method (DEM) simulations indicate that fine particles experience higher levels of collision energy per particle and this value reduces as the particle size increases and mill size reduces. This explains the higher Fractional mass loss rate of smaller particles as well as the increase in the Fractional mass loss rate as the mill size increases. Linked DEM and experimental data indicates that under these test conditions surface damage attrition is the dominant mechanism. This work suggests that DEM simulation can be implemented to predict the abrasion wear of particles in mills."

Jan 1, 2014

By X. L. Song

In this paper, ZrSiO4-Cd(S1-xSex) inclusion pigments were synthesized by hydrothermal method. Microstructure, morphology and properties of the powder were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR) and CIE chromaticity, respectively. It shows that, precursors obtained at pH is about 6.0 are sol and products with higher crystallinity, red hues (a*=38.23) and inclusion ratio when hydrothermal synthesis temperature is 180? and holding time is 12h. Hydrothermal reaction mechanism was further analyzed as well. In particular, an ideal model of pigment formation was proposed.

Jan 1, 2014

By Yasuhiro Konishi, Kazunari Mizoe

"This paper describes a new processing of ultrafine, magnetic ferrites from sulfuric acid pickling solution in steel industry. In the ferrite processing, the iron (II) in the pickling solution was first oxidized to iron (III) by using the acidophilic thennophile Acidianus brierleyi. The bio-oxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic solution of tertiary aliphatic monocarboxylic acid. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were hydrolyzed and precipitated ultrafine particles of crystalline ferrites at l90°C and l. 3 MPa for 20 min.IntroductionHot-rolled steel sheet has always a layer of oxides on its surface. The oxide layer arises as scale in hot rolling processes in steel industry, and the scale consists of the three iron oxides such as hematite Fez03, magnetite Fep4, and wustite FeO. Pickling removes chemically the scale layer that adheres to the steel surface. For normal steels, pickling is carried out in 15-20% hydrochloric acid at 60-70°C or in 20-25% sulfuric acid at 95-100°C. When steel is pickled with sulfuric acid, the scale oxides dissolve to give iron (II) sulfate.Spent pickling solutions are hazardous wastes containing a large amount of dissolved iron (II) and sulfuric acid, e.g., about 40 kg/m3 of dissolved iron (II) at pH 0. In typical commercial processes, spent pickling solution is usually cooled evaporatively to 5°C, and then to 0°C to crystallize iron (II) sulfate as its heptahydrate. After the crystallization operation, the sulfuric acid can be reused in the pickling operation.In this paper we describes a new processing of ultrafine, magnetic ferrite from sulfuric acid pickling solution, in order to recover dissolved iron (II) in the form of a valuable product. In the ferrite processing, the iron (III) was first supplied by the microbial oxidation of iron (II) in the pickling solution, and then the biooxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic carboxylate solution. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were precipitated crystalline ferrites under hydrothermal conditions."

Jan 1, 2000

By Pascal Turcotte

_ Introduction _ LaRonde _ Controlling Instability in Haulage Drifts _ Failure mechanism in drifts walls _ Failure mechanism in drifts back _ Field Behaviour of Support Elements _ The ?Hybrid Bolt? _ Conclusions

Feb 1, 2008

By Rafal Misa

In order to prevent the formation of mining damage or to reduce its reach, it is advisable to look for technical solutions which would enable effective protection of construction sites from the impacts of underground mining. So far, other authors have mainly focused on developing methods of securing construction sites in order to minimize the damage resulting from underground mining; the issue of geotechnical methods for protecting buildings against mining damage has not been thoroughly covered in those articles. It should be noted that there are relatively few publications directly related to this issue, nor are there practical examples of geotechnical protection. In this paper, a geotechnical solution available for securing building structures is discussed. Trenches presented in this research reduce the size and range of mining deformation. The results of numerical modelling for sample protective solutions, aimed at reducing the impact of mining activity on the terrain surface under various conditions, are presented. The calculations were performed with the aid of the Abaqus 6.10-2 software, based on the Finite Element Method.

Jan 1, 2014

By Dumitru Mitrica, Vasile Soare, Elvira Alexandrescu, Mihai Ghita, Marian Burada, Petru Moldovan, Raluca Maria Florea

"Aluminum metal matrix composite Al-Si /SiCp was prepared by reactive gas injection and subsequent remelting. The influence of the remelting process on the microstructure and physicalmechanical properties of the resulted material was investigated. Samples resulted from the synthesis process contained silicon carbide agglomerations in the vicinity of primary silicon and large pore concentrations. In-situ formed silicon carbide presented mostly a polymorphic structure with particle sizes varying from 1 to lOµm. Physical and mechanical properties were largely influenced by the porosity distribution. The remelting process provided a decrease in the composite material porosity and pore size, with significant improvements in the particle distribution and physical-mechanical properties of the composite material. Additions of up to lwt.%Mg in the starting alloy improved the in-situ carbide formation and particles distribution in the solidified material. However, stable and large particle agglomerations were detected in the material in absence of conventional stirring or controlled solidification techniques.IntroductionThe remarkable properties of composite materials (yield strength, stiffuess, hardness and resilience at a reduced specific weight) make them attractive for applications in automotive, aerospace and military industries. Particle reinforced aluminum metal matrix composites (PAMMC) are known for their high strength to weight ratio. The recent development of P AMMC created the possibility to obtain large particles concentrations, exceeding 10% by volume ofreinforcement (SiC, AIN, Al203, etc.). The improvement ofhigh temperature strength and wear resistance made them appropriate for the use in automotive applications, such as the pistons, rotors, disc brakes, and propeller shafts [ 1]. The present main disadvantage of the P AMMCs is their high costs for obtaining and processing related to the final product performance. In order to benefit from the advantages that offer composite materials properties a reasonable production cost - performance ratio must be obtained [2]. Recent innovations in the manufacturing of aluminum-based metal matrix composites provided notable performance improvements but no feasible solutions were found for lowering their present high prices."

Jan 1, 2014

By P. K. Songfack

The transport of slurry within the ball mill depends on the peripheral velocity and porosity of the ball charge. Residence time distribution and mill hold up are of-ten used as indicators of the mode of transport. In this work, the transport problem is tackled via direct simulation of the three dimensional motion of the ball charge. In doing so, the following quantities are calculated: (i) ball size distribution as a function of the distance from the feed end of the mill (ii) mean peripheral and longitudinal velocity and longitudinal velocity of balls of different sizes, and (iii) the spatial distribution of porosity within the ball charge. Hence, the problem of transport is handled as a motion of part of the slurry with the ball charge and part as hydrodynamic flow through the porous structure.

Jan 1, 1993

By Jie E. Zhou, Yu U. Wang

"Development of crystallographic texture in polycrystals during templated grain growth process is studied by phase field modeling and computer simulation. To characterize the grain texture development, X-ray diffraction peak intensities are computed for the evolving grain structures as simulated by the phase field model, based on which Lotgering factor is further calculated as a quantitative measurement of uniaxial texturing. While the phase field modeling allows direct comparison between simulated grain structures and experimental microscopy observations, the computational diffraction allows convenient correlation between computer simulation and experimental X-ray diffraction characterization. The latter feature is especially desirable, since microscopy experiments normally require more efforts than X-ray diffraction, and diffraction is usually the preferred choice for material characterization.IntroductionThe properties of individual grains in polycrystals are generally anisotropic, while untextured polycrystalline materials with random grain orientations exhibit isotropic macroscopic properties that are independent of directions. In order to achieve anisotropic response in polycrystals, crystallographic texturing of grains is required [1]. Texture refers to the collective distribution of grain orientations towards preferred orientation in a polycrystal. To develop texture, special processing routes are needed, such as templated grain growth (TGG) for uniaxial texture [2]. TGG has been shown to provide uniaxial texture in wide variety of materials. For example, [001]-textured ferroelectric polycrystalline ceramics have been fabricated by TGG process, which exhibit enhanced piezoelectric properties [3]. Such highly textured polycrystalline materials offer better cost-performance ratio than single crystals. Thus, texture development in polycrystals is of technological importance for material applications.In this computational work, grain texture development in polycrystals during TGG process is studied. Grain structure evolution is simulated by phase field model, X-ray diffraction peak intensities for the evolving grain structures are computed, and Lotgering factor is calculated to quantitatively measure the development of uniaxial texturing. The phase field modeling allows direct comparison between simulated grain structures and experimental microscopy observations using imaging techniques such as scanning electron microscopy or optical microscopy. The computational diffraction allows convenient correlation between computer simulation and experimental X-ray diffraction characterization. The latter feature is especially desirable, because microscopy experiments normally require more efforts than X-ray diffraction, thus diffraction is usually the preferred choice for material characterization."

Jan 1, 2014

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By A. Vidyadhar

Using pure quartz and hematite minerals, the adsorption mechanism of mixed cationic/anionic reagent schemes was investigated through Hallimond flotation studies. The flotation response of quartz and hematite independently with cationic and anionic collectors as well as with mixed cationic/anionic collector systems is assessed. The flotation response as a function of pH and collector concentration was investigated. The single mineral flotation tests in the presence of anionic collectors, quartz does not respond to flotation, but the C12 amine flotation of quartz was observed to be pH and concentration dependent. It was observed that hematite flotation recovery is maximum at acidic pH with sodium dodecyl sulphate (SDS), neutral pH with oleate, and at basic pH about 9.5 with C12 amine. Flotation results with both quartz and hematite indicate an increased adsorption of cationic collector in the presence of anionic collector apart from its own co-adsorption. The incorporation of oleate in between C12 amine molecules decreases the electrostatic head-head repulsion and thereby increasing the adsorption of C12 amine due to attractive tail-tail hydrophobic bonds, besides forming a closely packed adsorbed layer enhancing the hydrophobicity. The increase in oleate concentration beyond C12 amine concentration leads to the formation of soluble C12 amine-oleate complex / precipitate and the adsorption of these species decreased the flotation since the alkyl chains are in chaotical orientation with a conceivable number of head groups directing towards the solution phase. Keywords: quartz, hematite, adsorption, mixed collector system, flotation, zeta-potential

Sep 1, 2012

By Christopher Laughton

A new underground laboratory is under construction at the recently closed Homestake Gold Mine, Lead South Dakota, United States of America. The Deep Underground Science and Engineering Laboratory is designed to meet the needs of an international group of scientists and engineers interested in conducting fundamental and applied research at depth in the Earth’s crust.

Jan 1, 2011

By Junji Shibata

Heavier rare earth, which is contained in a small amount in ores such as bastnesite and monazite, has been accumulated as a heavier rare earth residue without doing separation and purification due to the lack of suitable methods. The heavier rare earth residue includes seven rare earth elements such as Tb, Dy, Ho, Y, Er, Tm and Yb. Separation and recovery process of Dy, Y, Tm and Yb from leached solution of the heavier rare earth residue was investigated by using a column method with solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organophosphorous extractant whose trade name is PC-88A into a macro porous resin, Amberlite XAD-7. It was almost impossible to separate them in simple adosorption and elution steps. However, we attained to individually separate Dy, Y, Tm and Yb from the leached solution first by changing eluent concentration gradually from pH2 to 0.02kmol/m3 HC1 in the elution step, and secondly by using a development column and changing eluerit concentration in the elution step. The separation process flow was proposed for a heavier rare earth residue by using the solvent impregnated resin method.

Jan 1, 1998

By László Guczi1

Nanosize model gold particles with varying size were fabricated by deposition of a 10 nm thick gold film onto SiO2/Si(100) substrate by electron beam evaporation followed by modification using low energy Ar+ ion bombardment. The change in particle size were monitored by the Au 5d valence band states determined by ultraviolet photoelectron spectroscopy (UPS). The gold/iron oxide interface was studied by iron oxide deposition on gold. It was found that the energy profile of Au 5d valence band states are strongly redistributed with decreasing the gold particle size mostly affecting at the lowest and at the highest binding energies. The size effect in the UPS spectra can be interpreted by the energy redistribution rather, than by narrowing the 5d states. The iron oxide deposition increases the catalytic activity in CO oxidation whether it is on gold nanoparticles or on a continuous 80 nm thick gold film. The activity enhancement is significantly larger in case of gold nanoparticles. The interface interaction is operative in enlargement of the catalytic activity even if gold particles are not exposed to the surface, but they are located below the iron oxide layer.

Oct 1, 2003

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015