Search Documents

By John B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals, but any curriculum that does not provide background in such basic subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to utilize geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors and may be faced with legal, social, and political problems in land use, zoning, environmental protection, and reclamation.

Jan 1, 1981

By O. V. Bush

Most governments recognize that energy efficiency represents a partial solution to reducing global capital shortages and environmental crises that threaten to seriously impede economic growth. Much of the United States and many foreign countries are embracing the concept of Integrated Resource Planning (IRP) which incorporates Supply Side Management (SSM) and Demand Side Management (DSM). Since SSM comes at twice to three times the cost of DSM, it makes economic sense to employ the energy conservation techniques of DSM. This paper will explain these concepts and some of the incentives being put forward by governments and utilities to promote DSM.

Jan 1, 1995

By S. B. . Tyrrell

This paper describes research carried out to develop and optimise a process to extract lithium from the processed waste of spent lithium ution of lithium salts can be used to produce a pure lithium hydroxide solution, From this, lithium carbonate is produced, the major precursor for other lithium chemicals and for new lithium batteries. Hence, the recycle loop can be closed. Significant variation in the composition of the battery waste has been observed. Small amounts of metals other than lithium and certain anions can present technical difficulties such as electrode dissolution and membrane fouling. Pre-treatment of the waste, together with an optimum combination of cell materials and operating parameters has been found to enhance separation and alter the energy consumption of the process.

Jan 1, 1999

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By Gaom M. W.

The Mount Isa copper concentrator started operation in 1973. Its secondary grinding circuit consisted of two 5 meters diameter ball mills in closed circuit with 505 mm cyclones. At the design throughput of 800 t/h, the 80% passing size of the circuit product (P80) was about 140 µm. The then Mount Isa Mines Limited (?MIM?) installed two autogenous grinding (?AG?) mills in 1991 to replace two stages of crushing, a rod milling stage and one primary ball milling stage. One of the AG mills was later converted to semi-autogenous grinding (?SAG?) operation by the addition of a steel grinding medium to achieve the designed plant throughput of 800 t/h. The cyclone over-flow P80of the secondary ball mill circuit was reduced to 120 µm by the increased operating power in the AG/SAG mill circuits. The two secondary balls mills had a grinding power of 5.2 MW. A mineralogical study of the milled products indicated that half of this grinding power was sufficient for adequate chalcopyrite liberation. Eliminating one of the secondary ball mills could reduce energy and operating costs by more than A$2 million dollars per year. An optimisation project team was established to achieve the predicted power saving. Grinding circuit simulations were conducted for different circuit configurations. Ball mill parameters such as ball size, ball charge and feed slurry density were optimised. Cyclone body diameter, spigot and vortex finder sizes, and cyclone types were tested. The secondary ball mill circuit was redesigned and several proposed circuits were run as trial production campaigns to determine their operability and efficiency. The plant trials confirmed that one of the secondary ball mills could be decommissioned. Significant cost savings were achieved as a result. The success of the project demonstrates optimising grinding circuits can not only deliver the plant performance, but also a much lower unit operating cost through energy and maintenance savings.

Jan 1, 2014

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By W. W. Albrecht

I. Introduction Refractory metals like tungsten, molybdenum, rhenium, tantalum and niobium and their compounds are essential ingredients of our modern technology. Especially in purified form, they are used in special alloys, electronics, optics and ceramics. The processing route from raw material to high purity refractory metals and their compounds includes, as a prime option, the following steps: - dissolution of raw materials. - liquid liquid extraction. - precipitation of high purity intermediate compounds. - calcination/reduction to high purity oxides/metals. Especially in the first three steps, major amounts of chemicals like acids or sodium hydroxide are used and, as by-products, substantial quantities of residues and effluents are generated. The impact of environmental regulations on these by-products and the attempt to reduce or minimize the amount of residues and effluents produced will be discussed in this presentation using Ta/Nb chemistry as the example. The basis of our considerations will be the way these by-products are handled at HCST, a major, and in some cases, the biggest producer of refractory metals (tungsten, molybdenum, rhenium, tantalum, and niobium).

Jan 1, 1992

By T R. Meng, C Wu

After carrying out a brief review of the existing safety assessment criteria for the spontaneous detonation of explosives in the mining of sulphide ore deposits in China, and giving a detailed description of the dynamic process and mechanism of the spontaneous detonation of explosives and the relative factors, the latest research results of three kinds of explosives reacting with a group of sulphide ores are presented, based on a reliable experimental method. Afterwards, a complete safety criterion for spontaneous detonation assessment, which depends on the hole temperature, the water solution Fe2+ and Fe3+ and the pH value, is established to determine (he safe charging time of explosives in variable conditions. The criterion is verified as correct by a large-scale field test.

Jan 10, 1996

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015

By Ricardo Wilson Nastari Denigres Filho

Durante estudos de síntese hidrotérmica (realizada em presença de ácido acético e em autoclave à temperatura de 160oC) com o propósito de obter-se boemita a partir de uma gibsita comercial, observou-se uma morfologia diferenciada nos cristais de boemita obtidos: os mesmos apresentaram-se na forma de placas finas de perfil pseudohexagonal. No entanto, quando a síntese é conduzida nas mesmas condições de temperatura somente em água destilada, a morfologia da boemita formada é a de cristais cúbicos. No intuito de tentar entender o mecanismo do crescimento dos cristais de boemita na presença de íons acetato, foram realizadas novas sínteses, envolvendo o mesmo procedimento de preparação, porém variando os meios nos quais a reação ocorre. A partir de novas sínteses realizadas com acetato de potássio em meio aquoso neutro (pH=7) ou ácido (pH=2), foi observado que a presença do íon acetato no meio reacional é determinante para a obtenção da morfologia lamelar. A estrutura cristalina dos cristais obtidos foi caracterizada por DRX e a sua morfologia foi examinada por MEV.

Aug 8, 2018

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By D. K. Weatherley, T. P. Oladele, L. B. Bbosa

Comminution is a critical stage of mineral processing which aims to reduce the size of ore particles through breakage, consequently increasing the likelihood of liberation of valuable minerals. Several factors, such as pre-existing cracks, mineralogical composition and particle size, are known to affect ore breakage behaviour. While investigating the contributing role of each factor is essential to improve understanding of breakage, isolating individual factors by experiment is typically impractical. Numerical techniques such as the Bonded Particle Model-Discrete Element Method (BPM-DEM) have been developed as a means of studying closely controlled breakage conditions. This study evaluates this technique in modelling the effect of pre-existing cracks breakage behaviour for synthetic ore specimens during impact breakage in a short impact load cell (SILC). Synthetic ore was modelled as a collection of discrete entities connected by brittle-elastic beams. Model parameters were calibrated against macroscopic material properties of a conventional homogenous synthetic ore. The extent of pre-existing cracks within specimens was prescribed by varying discontinuities between the connecting entities. An approach with the insertion of seed points was used to model the mineralogy of the specimens. Results showed that pre-existing cracks resulted in a decrease in the fracture force as the crack density increased. Additionally, the irregularity of fracture patterns within rock specimens after impact became more apparent as the crack density increased. The findings were used to emphasise some of the attributable causes of the variation observed between ore hardness characterisation tests and in situ ore behaviour. Keywords: Element Method; Bonded Particle Model, synthetic rock sample; rock fracture, preexisting cracks

Jan 1, 2020

By N. Naude, W. P. Roux

Fine particle beneficiation plays an ever-increasing role in mineral processing plants and it seems that technology can’t keep up with the challenges involved in the treating of these fines. The REFLUX™ classifier has proven itself able to treat high tonnages of fine material, especially in the coal industry. There are various fine ore applications that can benefit from such a process, yet laboratory and pilot-scale tests on many of these ores show poor efficiencies and recoveries. A better understanding of the design, operation and mechanisms of the REFLUX™ classifier is required to determine if and how it fits into these applications. The mechanisms in gravity separators are very complex due to the complex hydrodynamics, and the REFLUX™ classifier is no exception. The mechanisms of these systems are usually described through theoretical single particle-models that are hard to verify through analysing the feeds and products of these processes. To verify these models the movement of individual particles must be measured, which is not an easy task. In this paper the separation mechanisms in the incline channels of the REFLUX™ classifier were investigated with high-speed videography. A small lab scale model of the incline channel was constructed for this purpose. It was possible to capture and track the trajectories of particles under certain conditions and match these trajectories with theoretical models. The resuspension of particles, clustering and streaking was also observed and captured. Keywords: REFLUX™ classifier, particle trajectory, beneficiation, high-speed videography

Jan 1, 2020

By Chonghe Li, Xionggang Lu, Wei Xiao, Xingli Zou, Weizhong Ding

The reduction degree and rate of the initial ilmenite concentrate and pre-oxidation samples by hydrogen were investigated by using thermogravimetric analysis system. H2-TPR was used to detected reduction properties of the pre-oxidation products which were oxidized at different temperatures. The phase transformations and micromorphology changes during pre-oxidation and hydrogen reduction were identified by XRD and SEM. The FeTiO3 was decomposed into TiO2 and Fe2O3 at the temperature below 900 oC. With the temperature rising, Fe2TiO5 was the only stable phase in high temperatures. The reduction of pre-oxidation ilmenite concentrate was faster than the natural sample, which was attributed to the micropores generated on the surface of ilmenite concentrate during oxidation. The main phases of the reduction product were metallic iron, ferrous pseuodbrookite.

Jan 1, 2014

By Bo Jiang, Jiusan Xiao, Hongmin Zhu, Kai Huang, Shuqiang Jiao

Carbothermal selective reduction of simulative titanium slag and various titanium raw materials were presented and SiO2 was found to be partially reduced, forming a series of Fe-Si alloys during the process. Thermodynamic analysis of the selective reduction between TiO2 and SiO2 was performed using HSC 6.0 software, then a series of equilibrium experiments were designed and presented. The activity of Si reduced from SiO2 was affected by the presence of Fe reduced from FeOx and the generation of Fe-Si alloys, promoting the reduction of SiO2 in the whole process. The results of experiment are in great accordance with the calculated data obtained from thermodynamic analysis.

Jan 1, 2016

By Yuanbo Zhang, Zhixiong You, FENG ZHOU, Guanghui Li, Zhengwei Yu, Zhiwei Peng

Reduction disintegration of sinter significantly affects the coke consumption and productivity of blast furnace smelting. As we know, the reduction disintegration index (RDI+3.15) of sinter obtained from titanomagnetite concentrate is relatively worse than those from ordinary iron ores. In this study, the effect of sintering parameters, mainly involving coke breeze dosage and basicity on sintering indexes was investigated using titanomagnetite concentrate as raw material in an experimental-scale pot. Subsequently, RDI+3.15 of the sinter was detected according to the Chinese standard of GB/T13242-91. The results show that RDI+3.15 rises with the increase of coke breeze dosage, while it decreases with increasing basicity from 0.5 to 2.0 and then increases in the basicity range of 2.0-3.0. Finally, the microstructure of sinter before and after reduction was studied. And the mechanism of reduction disintegration was preliminary revealed by analyzing the morphologies and distributions of minerals in the sinter.

Jan 1, 2015

By D Oliveira

The use of an equivalent continuum for a rock mass is not always suitable for situations where the failure is structurally controlled by discontinuities as in the case of wedges in the tunnel roof. In these instances, discontinuum approaches are usually preferred. Rock joints that are filled with soft infill are likely to be the weakest planes in a rock mass, having a dominant influence on its overall shear behaviour. In this case, the joint material model adopted for the discontinuities should be able to describe important mechanisms, such as asperity sliding and shearing, post-peak behaviour, asperity deformation, and the effect of the soft infilling. The latest version of a soil-infilled joint model is discussed here. It describes more comprehensively than previous models the occurrence of dilation and compression with lateral displacements, and also represents the hardening mechanism related to asperity interference as observed in the laboratory that cannot be readily captured by the existing joint models. An analytical approach for the analysis of rock wedges structurally controlled by soil infilled joints is presented.The analytical approach presented in this paper for assessment of symmetric rock wedges in the roof of a tunnel demonstrates, that the peak shear strength of the joint may not be fully mobilised before detachment of the wedge. The analysis verifi ed that an overestimation of the factor of safety may be observed when an elastic-perfectly-plastic joint model was assumed, whereas the computed maximum factor of safety was considerably less when adopting an appropriate soil-infilled joint model.

Mar 8, 2011

By Wei-Tong Du, Xiao-Ping Liang, Yu Wang

The structural properties for ternary molten CaO–SiO2–B2O3 system with varying B2O3/SiO2 ratios at a fixed CaO content were calculated by molecular dynamics (MD) simulation. The simulation results revealed that with the increasing of B2O3/SiO2 mol ratio, the bond length of B-O was approximately constant at 1.35 Å, and the coordination number for B (CNB-O) was observed to vary from 3.40 to 3.51, and the average angle of O-B-O increases from 105° to nearly 120°, implying that the geometric stability of structure is reducing sharply. AlsoQ3 andQ4 tetrahedral species (tetrahedron with three and four bridging oxygens respectively) decrease with the increasing of B2O3/SiO2 mol ratio, and the proportion of (Q3 + Q4) decrease linearly from 0.6 to nearly 0, suggesting that B2O3 may behave as a network-breaking basic oxide in the CaO–SiO2–B2O3 system.

Mar 1, 2017

By Liangying Wen, Jian Xu, Dongdong Wang, Kaihui Ma, Yang Xu

Slags play an important role in blast furnace operation, and their com- positions are based on the CaO –SiO2–MgO–Al2O3 quaternary system. However, there is not a clear understanding of the effects of gangue on of the formation of FeO-bearing primary-slags process in blast furnace. In this work, the softening and dripping experiments under the blast furnace conditions are designed to explore the influences of CaO-/SiO 2-/MgO-/Al2O3 on the softening and melting properties of FeO respectively. The results indicate that additions of CaO or Al2O3 decrease the starting softening temperature and no dripping behaviors are found in comparison with the base case results when only FeO is used. On the contrary, the addition of SiO2 or MgO rises the starting and ending softening temperature, as well as the dripping temperature. The lowest maximum pressure drop is obtained in the case with addition of SiO2. According to XRD analysis results, the initial phase with CaO addition in the primary-slags should be CaOFe3O4 and that with SiO2, MgO, Al2O3 additions are fayalite (2FeOSiO2), magnesioferrite (MgOFeO), hercynite (FeO2Al2O3), respectively.

Mar 1, 2017