Search Documents

By Wescomb R. Jones

The United States is the world's largest producer of hydrofluoric acid (HF), with its 1971 output of 317,000 short tons representing about 40 percent of the estimated Free World production. U. S. production has increased over five fold in the past 20 years, with a growth rate of about 7 percent per year between 1960 and 1970. However, the growth rate to 1977 is expected to be less than 5 percent per year, due primarily to a reduced rate of growth in requirements by the aluminum industry and an expected increase in imports from Canada and Mexico. This discussion will include our analyses of the consumption pattern for HF in 1972 and the factors influencing the demand forecast for 1977.

Jan 1, 1973

By Eric J. Beckman

Recovery of metals from dilute solution, whether the matrix is solid, or liquid, remains a considerable technical and financial challenge. Methods currently exist whereby metals can be extracted from either type of matrix, yet these methods consume significant quantities of reagents and can also generate multiple waste ,streams in the process. Technology developed in our lab allows efficient application of environmentally-benign CO2 to a number of separation problems involving metals. For example, we have employed biphasic mixtures of C02 and water as a green acid leach medium. Metals have been extracted from a steelmaking process residue and then recovered as metal carbonates through depressurization. In this process, metals are extracted and recovered without the use of reagents other than CO2 and water, and CO2 is sequestered as a solid. In addition, through synthesis of Cal-miscible phase transfer agents, we have shown that CO2 can replace the organic solvent currently used in refining of precious metals, The sensitivity to pressure of phase behavior in a CO2-mixture may allow significant streamlining of the process as well. Finally, CO2 soluble chelating agents have been used to extract toxic metals from acidic effluent such as that found in plating facilities.

Jan 1, 1999

By F. Calizaya

A booster fan is an underground fan installed in series with a main surface fan and used to boost the air pressure of the ventilation air passing through it. To accomplish this objective, the fan is installed in a permanent stopping and equipped with airlock doors, a monitoring system, and interlocking devices between main and booster fan controls. The stopping and doors are used to prevent flow recirculation, and the monitors to ensure safe operation of the fan. A booster fan, properly sized and sited, can be used to create safe work conditions and allow the extraction of minerals from areas that would otherwise be uneconomic to mine. In deep and large mines with heavy emissions of air contaminants, the required quantities of air can only be supplied by using high pressure fans. These fans will inevitably induce significant losses of fresh airflow through the stoppings and doors. For well defined ventilation circuits, booster fans can be used to decrease the main fan pressures and reduce the leakage flows. However, this will require a good understanding of the correct ventilation practice, from planning to operation and maintenance of booster fans. The objective of this study is to investigate the conditions under which booster fans can be used safely and efficiently in underground coal mines. Specifically, the study is directed at (1) collecting reliable information on airway resistances and flow requirements from two large U.S coal mines, (2) collecting fan performance data from one or more existing coal mine where booster fans are used regularly, (3) monitoring the performance of booster fans in a laboratory model and an experimental mine, (4) developing a booster fan selection method to assist the ventilation engineer at the planning stage, and (5) training six M.S. or Ph.D. graduate students in advanced mine ventilation.

Jan 1, 2010

By R. R. Klimpel

The process of flotation is an extremely important solids separation technique employed in a wide variety of industrial process applications. Froth flotation is practiced in the coal industry to recover fines produced during the mining and cleaning of coal. A recent review article by Aplan (1) covers the processing variables encountered in the flotation of coal and the variety of chemicals and operating conditions which affect recovery. Numerous engineering and scientific studies have been performed with the goal of providing semifundamental laws of flotation behavior for improved screening of flotation chemicals, better equipment scale-up factors, etc. Often the results of such work are expressed in the form of mathematical models (e.g. 2, 3, 4, 5, 6) which are potentially useful for evaluating (simulating) on paper such alternatives as possibles process operating or configuration changes, the effects of ore and reagent changes, etc. It appears to be commonly accepted that a complete scientific/engineering characterization of flotation is immensely complicated and not sufficiently developed at the present to accurately predict (or understand) many important industrial facets of flotation. Thus, one is often reduced to detailed experimental characterization in both the laboratory and plant in order to fully evaluate flotation changes or alternatives. It is the purpose of this paper to describe a method of batch laboratory data characterization that is useful in evaluating flotation chemical reagents including froth flotation of coal. The approach consists of running a series of time-recovery curves in a batch float cell followed by the computer curve fitting of this data to a series of mathematical models based on semi-physical reasoning. The unknowns or parameters of these models are then optimally chosen so as to best fit the experimental data. It has been found in both coal and mineral systems that changes in reagent type, concentration, system pH, grind, etc. cause very consistent and logical changes to

Jan 1, 1979

By Jaco van den Berg, Dr. Todor Petrov, Dr. Josh Calnan, Dr. Jhon Silva

This paper shows and reviews the similitudes and differences in explosions generated by high explosives and gas explosions, the reasons why gas explosions are difficult to replicate using high explosives, and the considerations when performing explosive testing using methane gases and coal dust.

Feb 1, 2020

By A. B. Parsons

DOWN in Washington an army of individuals constituting the government of a so-called "'democratic" nation is trying to manage the conduct, in its rnultifold phases, of the greatest war in history for the country that is potentially, at least, the strongest in the world and on which, consequently, the major responsibility rests. The enterprise is one of unprecedented magnitude and complexity. That individuals and groups have made and are making serious blunders, both as to the establishment and execution of policy, is to be expected.

Jan 1, 1942

By D. Lynn, D. Arthur

Infrastructures continue to age and drinking water supplies are becoming scarce in the San Fernando Valley of Los Angeles, California. Frontier-Kemper Constructors, Inc. (FKCI) was engaged by the Los Angeles Department of Water and Power (LADWP) to complete the River Supply Conduit Improvement Upper Reach—Unit 7 Project (RSC7). Two tunnel sections were bored using a 2.64 meter diameter Microtunnel Boring Machine (MTBM) and a 4.12 meter diameter Earth Pressure Balance Tunnel Boring Machine (EPBTBM) to excavate approximately 3,733 meters (3.7 km) of tunnels through highly abrasive late-Pleistocene-age Quaternary alluvial deposits (Old Alluvium) and Holocene age Young Alluvium deposits above the water table. This paper discusses the challenges encountered managing the TBM’s equipment degradation, use of soil conditioners, cutterhead wear, torque and advance rates while maintaining the necessary face-pressures and parameters to limit over excavation and ground settlement.

Jun 13, 2021

By Rodrigo Rangel Porcaro

Juntas soldadas por centelhamento (flash butt welding) de trilhos de aço do tipo intermediário foram caracterizadas mecânica e estruturalmente. Além disso, ensaios preliminares de dilatometria foram aplicados ao metal base e correlacionados ao processo de soldagem. Os resultados indicam que o metal base atendeu aos requisitos da Norma AREMA (2013). A microestrutura de toda a região soldada é formada por perlita e os ciclos termomecânicos provocaram significativas alterações no tamanho das colônias perlíticas e na sua morfologia, com destaque às mudanças de espaçamento interlamelar em toda a junta e início de esferoidização na região de transformação parcial. Como consequência das alterações morfológicas da perlita, a microdureza foi significativamente reduzida na região de transformação parcial e refino de grãos. A taxa de resfriamento média após o processo de soldagem foi estimada a partir dos ensaios de dilatometria.

Oct 30, 2017

By Marco A. Ramírez-Argáez

A 2D mathematical model was developed for the plasma arc welding process. Computational simulations based on mass and momentum conservation equations as well as Maxwell equations were performed by using the commercial software PHOENICS. The model predicts the electric characteristics of the arc column, flow patterns, temperature contours and electrical potential, by varying the composition of the cover gas, in this case, argon and nitrogen. It was found that an arc of nitrogen with respect to one of argon generates more intense jets, greater voltages, and lower temperatures in the arc column for welding arcs current of 150 A and 10 mm arc length.

Oct 30, 2017

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

The Jundee gold mining operation is located in the Western Australian Yandal Greenstone belt. Jundee is a mature operation encompassing multiple and complex underground ore resources, dwindling open pit reserves, large surface stockpiles, small satellite resources and two near-mine but stand alone process plants. The imminent completion of continuous open pit mining and the associated drop-off in total mill feed precipitated a review of the strategic mine plan and development of options that would optimise the exploitation of the remaining mineral resources and the utilisation of the existing plant and infrastructure.An initial review of the strategic decisions to be made, available options as well as the quantity, complexity and co-dependency of the strategic variables quickly led to the conclusion that an Operations Research style modelling approach would be appropriate. An 'off-the-shelf' program engine by the name of WHATSBEST! (LINDO Systems Inc.) was chosen on the basis of price, reputation and ease of use. The model was formulated with the unknown variables (being the ore mining rates) expressed as a proportion of the maximum achievable ore mining rate from each source. Costs were defined as variable or fixed, with this definition being a key aspect of the modelling process. The critical application of the model was in determining the optimal extraction rate of ore, the destination (ie Jundee or Nimary mill) and the sequence of extraction of each ore source that maximized the cash flow of the operation. The program was designed to be able to quickly derive an optimal result from the many variables, replacing the previous laborious iterative process of arriving at an acceptable answer by means of several large and static spreadsheet models. This paper presents the process of selection, formulation, application and scope of operation of the turn-key linear and non-linear program strategic model now used as part of the Jundee Operation strategic decision making process.

Jan 1, 2002

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By S. Banisi, A. Ghasemi, A. Fazeli, M. Rezaei, M. Maleki-Moghaddam

The efficiency of high capacity SAG mills which consume large amounts of energy depends on the grinding and slurry discharge systems. A 9.7 m × 4.8 m SAG mill with radial pulp lifters is used at the Sarcheshmeh copper complex grinding circuit. The process audit indicated that the pulp discharge system was not efficient, judging by the amount of slurry flow back and carry over. These events limited the discharge rate and increased the wear rate of the lifters and grates. With the objective of finding a new design for pulp lifters, a 3D DEM software (KMPCDEM ©), along with the plant operational data and photographic evidence was used. The KMPCDEM © software was used to compare the efficiency of the radial and curved pulp lifter design based on the material flow. The slurry flow was analysed in terms of ease of discharge and lifter wear rate. It was found that changing the radial pulp lifters to curved pulp lifters could improve the discharge efficiency,and decrease wear rate of the pulp lifter in particular at the base of the pulp lifters. The simulation results showed that if curved lifters with a radius of 0.3×mill radius are used, the amount of slurry flow back and carry over will be negligible. It is predicted that by installing the curved pulp lifters, the capacity of the mill increases by 10% and the pulp lifter service life improves by at least 20%. Keywords: SAG mill, radial pulp lifter, DEM,curved pulp lifter, Sarcheshmeh

Jan 1, 2020

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997

By Lida Sun, Na Wu, Mengyang Huang, Xingxiang Fan, Yan Jiang, Shasha He, Kunbin Yang, Yang Cao

The separation of lead (Pb) and mercury (Hg) from copper (Cu) smelting acid sludge using the carbonization and acidleaching total hydrometallurgical process was investigated. The effects of the excess coefficient of sodium carbonate, excess coefficient of nitric acid, conversion time, conversion temperature, dissolution time, and dissolution temperature on the separation efficiency of Pb and Hg were studied. The test results indicated that when the dosage of sodium carbonate was 2.0 times the stoichiometric ratio, the conversion time was 1.5 h, the conversion temperature was 75 ℃, and the amount of nitric acid was 1.8 times the stoichiometric ratio. Additionally, the dissolution time was 1.0 h, the dissolution temperature was 60 ℃, the ratio of liquid–solid was 5:1, and the separation efficiency of Pb and Hg was 98.72%. This study demonstrated the advantages of a short, simple, and environmentally friendly process for separating Pb and Hg from Cu smelting acid sludge, providing complete separation and introducing a new technology.

May 30, 2024

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By C. A. Young

Cyanide is a toxic species that is found predominantly in industrial effluents generated by metallurgical operations. Cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent accidental spills. Various methods of cyanide remediation by separation and oxidation, including photolytic advanced-oxidation processes, are therefore reviewed. Reaction mechanisms are presented throughout the paper. The methods are compared in regards to their effectiveness in treating various cyanide species: free cyanide, thiocyanate, weak-acid dissociables, and strong-acid dissociables.

Jan 1, 1996

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970