Search Documents

By N. Mungan

A study was made of the effects of wettability and interfacial tension on the immiscible displacement of a Iiquid by another Iiquid from porous media. The influence of viscosity ratio was also investigated. Porous media used were polytetrafluoroethylene (TFE) cores prepared by compressing TFE powder under different pressures. lt is shown that displacement of a wetting by a nonwetting Iiquid is always less efficient than the displacement of a nonwetting by a wetting fluid, all other things being equal. In the former case, the recovery efficiency can be increased substantially by either reducing the interfacial tension or increasing the viscosity of the displacing fluid. A qualitative discussion is given on the implications of this work to the recovery of crude oil by water flooding. INTRODUCTION The high cost of oil exploration and new recovery schemes makes it imperative that waterflooding be conducted under conditions favoring most efficient oil recovery. To improve oil recovery by waterflooding, it is essential that the role played by interfacial forces in the entrapment of residual oil be studied and understood. Interfacial phenomena in natural rock, connate water and crude oil systems are very complicated because of the complexity of the natural liquids found in petroleum reservoirs, because of our inability to adequately describe the geometrical structure of the porous media and because of a lack of understanding of physical and chemical interactions between the liquids and surface of the pores. The problem becomes further complicated when one tries to elucidate the role of interfacial phenomena in fluid flow. Numerous studies of the displacement of oil by water under different interfacial tension or wet-tability conditions have been made.lm3 These studies have been performed in silica, alundum or sandstone systems using water and paraffin oil and also some surface active material to control the interfacial tension s and the contact angle 0. Unfortunately, the high energies of various interfaces involved favor adsorption and orientation of the surface active material at the interfaces. Also the surface active material concentration at the interfaces exceeds that in the bulk of the liquid phases. Such surface excess may cause the surfactant distribution, the contact angle and the interfacial tension to differ from their measured static equilibrium values and makes interpretation of the displacement experiments difficult. Furthermore, as changes in s also lead to changes in cos 0, the role played individually by one of these parameters in the displacement becomes obscured by the effect of the other. To circumvent these difficulties, a low surface energy solid and true solutions or pure liquids should be used. Use of a low surface energy solid minimizes adsorption and orientation effects at the solid-liquid interfaces. By controlling s and cos 0 through use of selected pairs of pure liquids or true solutions rather than by surfactants, the adsorption effects at liquid-liquid interfaces are eliminated. In the present study TFE cores were used as the porous media. Liquids used were water, sucrose solutions, paraffin oils and benzyl, n-butyl and isobutyl alcohols. The interfacial tension was varied from 40 to 1.1 dynes/cm by suitably choosing the liquid pair. A surface active material was added to the water-oil system only in the case where interfacial tension of 0.5 dyne/ cm was desired. No precise changes of cos 0 were attempted. However, either the displaced or the displacing liquid could be made the one which preferentially wets the TFE surface. Using sucrose solutions and blends of paraffin oils proved to be a convenient way of changing the viscosity ratio between the displaced and displacing liquids. The present investigation examines the effect of interfacial tension, wettability and viscosity ratio on the immiscible liquid-liquid displacement from porous media. Observed data permit a

Jan 1, 1967

By W. Bonfield

The microstrain characteristics of a polycrystal-line Cu 1.9 wt pet Be precipitation-hardening alloy have been determined for various conditions of aging. The friction stress remained constant for all the conditions investigated, whereas the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-8 in. per in.) and the three-stage stress-strain curve in the microstrain region were sensitive to changes in dislocation and precipitate distribution. Correlations between the measurements of microplasticity and electron-nzicroscope observations of substructure are considered. ALTHOUGH the macroscopic mechanical properties of Cu 1.5 to 2.0 wt pet Be precipitation-harden ing alloys were established' in some detail, there has been no previous investigation of the nature of microyield-ing in these alloys. This paper describes a high-sensitivity extensometer determination of microplasticity in polycrystalline Cu 1.9 wt pet Be, in which the friction stress, the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.), and the rate of strain hardening in the micro-strain region were measured for various conditions of precipitation. The structural changes accompanying aging in this alloy were examined using transmission electron microscopy, a study which differed from previous investigations as, in order to minimize grain boundary precipitation effects,' the solution-treated alloy was cold-rolled to 40 pet reduction prior to aging. Hence the extent of recovery and recrystalliza-tion, as well as the variation of precipitate morphology and distribution, were assessed. From these results possible correlations between the microstrain characteristics and the observed precipitate and dislocation structure are considered. EXPERIMENTAL PROCEDURE The material investigated was a commercial copper beryllium alloy (Berylco 25), which had a com- position of 1.9 wt pet Be and 0.2 wt pet Co. The alloy was solution-treated at 800°C, quenched in water, and then cold-rolled to 40 pct reduction. Tensile specimens of gage length 1 in. and rectangular cross section of 0.18 by 0.06 in. were prepared from the solution-treated, cold-rolled material and aged for 15 min, 2, 24, and 100 hr at 315°C and 24 hr at 425°C to produce a range of precipitate structure. The hardness values associated with these conditions are listed in Table I. It can be seen that a maximum value is obtained after 2 hr at 315oC, which decreases with continued time at temperature to a minimum after 24 hr at 425°C. For comparison some as-solution-treated specimens were also aged for 2 hr at 315°C. The specimens heat-treated to a given condition were examined in two ways. First, the nature and distribution of the precipitate and dislocation structure was characterized using transmission electron microscopy. Thin foils were obtained from the specimens by electrolytic polishing in a 30 pet nitric acid-alcohol solution at -20oC, and were examined in an RCA EMU 3 electron microscope. Second, the mi-croplastic behavior of the specimens was measured with a Tuckerman strain gage, using the load-unload technique previously described2, 3 to determine the friction stress, the microscopic yield stress, and the variation of plastic microstrain with stress. RESULTS 1) Structural Changes During Aging. a) Annealing Processes. The solution-treated, cold-rolled Cu 1.9 wt pet Be had an irregular dislocation-cell structure,

Jan 1, 1968

C. M. Bishop (Aircraft Div., A. V. Roe Cnnada Ltd., Toronto)—Reference is made to the coherency hardening of ß due to ß' and also to the hardening of ß due to a coherent precipitation of the a phase. What is meant by the term "ß'?" Would not the coherency hardening of ß during cooling be due to precipitation of a sub-microscopic dispersion of a, as is the case during reheating a ß-quenched alloy? I feel that these two phenomena are essentially the same mechanism, i.e., precipitation of a from unstable or supersaturated ß. From the text, it would appear that Tables III and IV are intended to show the effect of the martensite transformation on the properties of Ti-Mn alloys. Referring to Table 111, the ß-quenched alloys would contain a greater proportion of retained ß than would the equilibrated alloy. Could not the increase in properties be attributed to this, along with possible coherency hardening of the ß? In the same way, the structures referred to in Table IV contain ß from which they could derive their hardness. It would appear to be difficult, if not impossible, to assess the role of the martensite transformation from the data contained in these tables. F. C. Holden, H. R. Ogden, and R. I. Jaffee (authors' reply)—In reply to the first question raised by Mr. Bishop, the term "ß"' designates an apparent retained-p structure which is harder than it is after the most rapid cooling from the ß field. It is thought to be the result of a coherent precipitation of a. The mechanism by which hardening takes place is undoubtedly the same as that involved in the early stages of aging of a re-tained-p structure, and we are in agreement with Mr. Bishop on this point. The term "ß'" to designate the anomalously hard retained-ß structure was agreed upon at a symposium in 1953." The authors do not agree that the quantity of retained ß and/or ß' in the ß-quenched specimens of Table III is necessarily greater than that of the 600°C equilibrated specimens. The ß-quenched specimen has a structure which appears to be completely a' formed by the martensite reaction. It is recognized that there could be some retained ß (or ß') between the a plates if the M, temperature is below room temperature. This is unlikely for the 3.4 pct Mn alloy where the M, is known to be at about 640°C. Therefore, the increase in strength cannot be attributed to the presence of a greater quantity of coherency-hardened ß, but, rather, the increase in strength must be attributed to the transformation products formed, e.g., a' (martensiti-cally formed a). Concerning the data in Table IV, we agree that it is difficult to estimate the role of the martensite reaction, since the 6.4 pct Mn alloy was retained ß in the quenched condition.

Jan 1, 1955

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of stock control. The percentages given rep¬resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geological Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is, one of the most important minerals, was omitted because not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By G. Swartz, R. J. Brison, R. A. Wyman, J. P. Vandenhoeck, S. E. Khalafalla

Magnetic fluids are commonly composed of ultrafine submicron particles of magnetite (Fe3O4) dispersed in either a kerosene or a water carrier medium with oleic acid as a protective colloid. The unique property of these fluids is that when the magnetic particles are attracted to a magnet the carrier medium moves along with the particles so that the liquid also appears magnetic. The availability of a fluid whose gross behavior changes sharply in a magnetic field without affecting its rheologic characteristics is becoming critical for many technologic applications. About two gener¬ations ago suspensions of relatively large, micron-sized ferromagnetic particles in oil proved useful in clutches, brakes, and dashpots. These were called magnetic clutch materials, and their viscosities were highly dependent upon the applied magnetic field, in contrast to true mag¬netic fluids which retain their fluidic characteristics under all applied fields and field gradients. While the term "ferrofluid" was used by Rosensweig and Kaiser&apos; to designate a magnetic colloid composed of a dispersed magnetic ferrous material, the more general term, "mag¬netic fluid," is preferred. This is because these fluids may contain ferro- or ferrimagnetic substances, such as cobalt, nickel, gadolinium, dysprosium, or magnetic ferrites in carrier liquids, such as hydrocar¬bons (kerosene), silicones, water, fluorocarbons, etc. Preparation of Magnetic Fluids Magnetic fluids were first prepared by Papell and Faber, at the NASA Lewis Research Center, Cleveland, Ohio, by tumbling ferrite materials for several weeks in a carrier medium (such as kerosene) and a dispersing agent (such as oleic acid) with steel balls. Rosensweig et al.1 compared the stability of their ferrofluids obtained from both metallic iron and the magnetic oxides of iron, Fe3O4 and yFe2O3. They found that, although the saturation magnetization of iron is 3.5 times greater than that of magnetite, its colloidal solutions deterio¬rated much more rapidly. The iron particles were undoubtedly rapidly oxidized to a nonmagnetic state due to the enormous surface area of these colloidal particles. Because the properties of these fluids are highly dependent on particle size and may acquire opposite characteristics by small incre¬ments in that size, more controllable methods of preparation have been developed recently by Khalafalla and Reimers.6 In one method metastabilized pyrophoric wiistite is ground to colloidal size in a kerosene oleic acid mixture, and then it is disproportionated to colloi¬dal magnetite and iron at temperatures just below the eutectoidal temperature of wüstite stability (570°C); thus, t < 570°C 4 FeO t > 570°C Fe + Fe30, (1) Because of its antiferromagnetic characteristics, the precursor wüstite is much easier to grind than magnetite. Another method3 avoids grinding entirely and utilizes a peptiza¬tion technique from ferrous materials in the molecular state of aggrega¬tion. This latter procedure has resulted in preparation of strong fluids at considerable savings in cost.

Jan 1, 1985

By F. N. Ward, E. H. Bailey

Camp and sample-site methods useful for determining about 0.5 to 16 ppm of mercury in soils and rocks have been devised to complement the analytical methods already widely used in geochemical prospecting. In the camp-site procedure the sample solution is obtained by digesting the finely powdered sample with hot nine-molar sulfuric acid and bromine, the latter generated in place. The solution is buffered at a pH of 4 and the mercury is extracted into a relatively small volume of an organic solvent. Estimations are made by comparing the color of the mercuric dithizonate extracted from the sample with that extracted from a standard. In the sample-site method the mercury is volatilized as the iodide and the latter is dissolved in a buffer solution from which the mercury dithizonate is extracted as in the camp-site method. The estimation is made by a similar comparison with standards or by comparing the color of the mercuric dithizonate with artificial standards prepared from Orange II, an azo dye. Except for the establishment of standards, the time required by an experienced analyst seldom exceeds 10 min for a camp-site determination and 5 min for a sample-site determination. Camp-site determinations are useful for commodity studies and intensive exploration programs; sample-site determinations are applicable to extensive and reconnaissance-type geochemical prospecting programs. The results obtained on samples taken along traverses above known mercury ore deposits in the California Coast Range and western Nevada demonstrate the usefulness of both methods in geochemical prospecting. The increasing use of the mercury content of soils, rocks, plants, or water in geochemical prospecting emphasizes the need for analytical methods which are sensitive and at the same time require a minimum of readily available equipment. Sensitive methods based on the absorption of ultraviolet light by mercury vapor are common in the literature31 12. Although none of these methods have been used to analyze the large number of samples required in geochemical prospecting, they could be extremely useful except for the expensive instrumentation usually required to make the methods quantitative Also, such methods are perhaps too sensitive for field use, especially around areas of possible contamination. Other methods involve the distillation of mercury from a relatively large sample and subsequent collection of the vapors in nitric acid6. The mercury is then estimated by titration with a suitable reagent such as thiocyanate. These methods are not trace methods because the actual amount of mercury measured is often as great as 50 to 100 milligrams. Also, such methods are unsuitable for geochemical prospecting because of the amount of equipment necessary and the time required. Still other methods involve colorimetry, and the sensitive reaction between dithizone and mercury (11).. is the basis for a number of reports on the determination of mercury in biological materials 5,7. Moreover, by the judicious use of solvent extraction and suitable complexing agents, the dithiaone method can be made almost specific for mercury. However, none of the dithizone methods have yet been applied to the determination of mercury in soils and rocks. In most colorimetric methods he sample solution

Jan 1, 1961

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By Charles White Merrill

Mankind&apos;s progress is measured in minerals. Man&apos;s emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

By G. M. Yocom

Blowing acid Bessemer converters with oxygen-steam produces steel of below 0.002 pct N2 content. This method of blowing, combined with a dephosphorizing treatment in the steel ladle, results in low-carbon steels of low nitrogen and low phosphorous (under 0.035 pet) contents, which has physical properties equivalent to open-hearth steels of similar analysis. Using a 50-50 mixture of oxygen and steam, the refinitzg rate is increased 25 pct over blowing with natural air, and scrap charge increased from 3 to 10 pet. Bottom life is normal with proper tuyere area and arrangements, fumes are decreased, yields increased, and hydrogen content is normal. THE acid Bessemer plant at the South Works of Wheeling Steel Corp., consists of two 15-ton bottom blown converters with a monthly capacity of 57,000 N.T. The product of the shop is skelp billets for continuous welded pipe and slabs for ordinary drawing and forming quality sheets. Approximately 50 pct of ingot production is regular Bessemer steel of natural Phos content and the remainder is a dephosphorized grade of steel made by a special treatment of the blown metal as it is poured into the steel ladle. The low Phos grade of steel has certain advantages over the higher Phos grade but since both grades were produced by blowing natural air, the N2 content was in the range of 0.015 pct which limited its application. In 1954 it was decided to explore the possibilities of blowing with a steam-oxygen mixture for the production of steel of both low N2 and low Phos contents. The necessary equipment was installed to operate one converter in this manner and early in 1955 an experimental run of 160 heats was made by blowing with a steam-oxygen blast and excluding natural air entirely. During this period the proper operating techniques were established, such as blast pressures, steam-oxygen mixtures, valves and instrumental control equipment, tuyere arrangement in the bottoms, blowing times and production rates, and a thorough study made of the final steel quality. Also during this experimental period the dephosphorizing practice was improved by the use of a tap hole below the lip of the vessel. This provided a clean separation of the acid converter slag and blown metal which made the dephosphorizing treatment more effective. The results of this experimental run dictated further development of this practice and a second run of 720 heats was made in 1957. The quality features and conversion cost results were in line with expectations and accordingly a 400-ton per day oxygen plant is now being installed. The plant is scheduled for completion in September of this year. This will provide sufficient oxygen to operate both vessels on steam-oxygen blast and delete natural air blowing entirely. The steel will then be below 0.002 pct N2 bar content and the dephosphorized grades will be between 0.015 and 0.040 pct Phos. STEAM-OXYGEN BLOWING The steam for the process is fed to the plant at 220 psig pressure through a 6-in. line. The high-purity oxygen is compressed to 200 psig and conducted through an 8-in. line. The oxygen from the main line is valved down to 100 psig and passed through a steam heated heat exchanger. The heat exchanger is regulated to supply oxygen at 300°F to the steam-oxygen mixing station. It is essential that the incoming oxygen be held at this temperature to avoid condensation of the steam with resulting excessive erosion of the clay tuyeres in the vessel bottom. Oxygen is admitted to the mixing chamber by a 6-in. hydraulically operated valve driven by the ratio control regulator on impulse from the flow of steam. Steam is admitted to the steam-oxygen mixture station through a 2 1/2-in. hydraulically driven valve. The ratio control regulator acts to increase or decrease oxygen input as the steam flow increases or decreases with changing positions of the Blower&apos;s control lever. The important point to note here is that steam flow always precedes the oxygen flow as a safety measure. The control valves have sufficient capacity to afford protection should blow pipe trouble develop. A 50-50 mixture for these 15-ton heats demands an oxygen flow of 3800 standard cu ft per min along with 317 lb of steam. The Blower&apos;s stations is provided with an indicating blast pressure gage, and indicating steam and oxygen flow meters. Signal and warning lights indicate the valve positions and line pressures. A control room at the real of the Blower&apos;s pulpit room houses the ratio control and pressure regulators, as well as the various meter bodies. The hand actuated wheels used to change the conditions are mounted on a panel on the front of the meter control house. The recording steam and oxygen meters used for totalizing and accounting purposes are also mounted on this panel.

Jan 1, 1962

By W. C. Smith

This Bureau of Mines report discusses how pull-test data can help establish polyester resin column length criteria for roof bolts in evaporite minerals. The study evaluates the effectiveness of partial to full columns of resin in anchoring 4-ft, No.6, grade 40 rebar roof bolts in potash, salt, trona, gypsum, and borate mine roofs. Pull tests were performed on over 600 roof bolts in 11 evaporite mines. Column lengths ranging from 6 to 48 in (fully grouted) were evaluated for each test site. In general, comparative results among all test sites indicate that pull-out loads in excess of 10 tons (force) were attained with resin-grouted bolts having 13 to 75 pet less than a full column of polyester resin. Ten tons (force) of load-carrying capability compared favorably, in terms of strength, with the calculated yield strength of the rebar used in the tests, which was 8.8 tons (force). The site-specific nature of each test site, due to the unique combinations of geology, mine-induced stresses, and other unknown parameters, prevented the establishment of valid generic column-length criteria. For these reasons, data to evaluate resin-column-length effectiveness are best obtained on a mine-specific basis.

Jan 1, 1987

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

By A. B. Calhoun

These mines, which belong to the Burma Corporation, Ltd., formerly a London company now incorporated in Rangoon, Burma, are situated in the semi-independent state of Tawng-Peng, one of the small divisions comprising the northern Shan states and erroneously known as part of Upper Burma. Bawdwin is approximately 23&apos; 6&apos; N. latitude and 97" 20&apos; E. longitude, 450 miles north of Rangoon, 169 miles northcast of Mandalay and 50 miles south and west of the Province of Yunnan, China (see Fig. 1). Although the mines were worked by the Chinese during the Ming Dynasty, 1412 A. D., the most extensive operations took place between 1796 and 1851, when the mines contributed largely to the silver market of China. During the reign of Tung Chik, 1868 A. D., they were abandoned partly because of the Mohammedan rebellion in Yunnan, which made life and property insecure, but largely because of the difficulty of operating the mines on account of water and poor ventilation. Since that time practically nothing was done, although the Burmese kings are said to have made several sporadic attempts to work the mines, until 1891 when Europeans were attracted by the great slag dumps (assaying about 40 per cent. lead) which the Chinese had left after extracting the silver. After a railroad and smelter had been built and 200,000 to 300,000 tons of slag smelted for lead, exploration work was started and old workings cleaned out in order to locate the remnants of the orebody that it was supposed the Chinese had left. After two years of most discouraging work, the remains of a large orebody was discovered by the Dead Chinaman Tunnel or what is the 171-ft., or No. 2 level adit. From then on the development was rapid and today the Chinaman is considered one of

Jan 1, 1923

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT Data frequently can be collected by several dif¬ferent methods. The method required for the nec¬essary precision for inflow prediction to mines should be selected and other methods avoided. Pre¬cision monitoring or measuring techniques fre¬quently require more time, expertise, and expense in their implementation that may not be justifiable. The temporal distribution of the data needs also may dictate the method used for data collection. Continuous recording devices may be required for time sensitive data whereas point measurements of other parameters may be adequate. Data needs will vary as the hydrologic investigation proceeds. In¬itial data needs may require only a qualitative col¬lection of data such as the areal distribution of precipitation. Subsequent data needs may require the measurement of ground water levels to the near¬est hundredth of a foot. Data requirements can be difficult to fulfill for ground water systems. This is particularly true for anisotropic, heterogeneous hydrostratigraphic units since the hydrogeologic parameters vary both ver¬tically and areally. Techniques exist for determining the storage characteristics of both unconfined and confined hydrostratigraphic units but these pro¬cedures require the installation of multiple wells in the same unit which may be impractical. Specific tests are discussed subsequently that permit the determination of vertical hydraulic conductivity. Data collected from field procedures or tests are generally preferred to laboratory derived data. This is especially true for hydrogeologic parameters such as hydraulic conductivity. SURFACE WATER SYSTEMS Precipitation Precipitation data can be collected from sources that maintain a historical record. The US Depart¬ment of Commerce, National Oceanic and Atmos¬pheric Administration (NOAA), maintains weather observation stations across the country. Such a sta¬tion frequently can be found near a proposed mine site but the type of weather data collected varies from station to station. Fortunately, precipitation data are collected ubiquitously. The data collected by NOAA can be purchased for the area of interest in the form of monthly and annual tabulations. Private weather stations constitute a second source of precipitation data. Existing data usually are analyzed by one of three methods. The station average method merely sums the depth of precipitation at each station and divides the sum by the number of stations as fol¬lows: [ ] where Pavg is the average precipitation (L), P, is the depth of precipitation at station i (L), and N is the total number of stations. This method is applicable where there are a relatively large number of stations uniformly distributed across the area (Hjelnfelt and Cassidy, 1975, pp. 71-72). The second method, called the Thiessen poly¬gon method, weights the precipitation at each sta¬tion in direct proportion to the area it represents without consideration of topography. The stations are plotted on a map and perpendicular bisectors are drawn on the lines connecting the stations. The polygons formed by these bisectors constitute the area that the precipitation for that station repre¬sents. The overall precipitation can be calculated with the following equation:

Jan 1, 1986

By J. D. Decker, T. E. Norman

Introduction Grinding is the reduction of ore and similar raw materials to particle sizes below the practical limits of commercial crushing ma¬chines. This size is about 36 in. (1 cm), in most cases, although some finer crushing machines are in regular use. The feed size to grinding machines may range upward to S in. in rod mills, and 12 in. or more in autogenous mills. The finest particle sizes produced in mineral processing operations result from grinding. Ordinary grinding of brittle materials is the result of impacting, rolling, and abrasion of heavy bodies, moving freely under the influ¬ence of gravity. These falling and rolling grinding bodies, which are usually of metal, must be much heavier and larger than the ore parti¬cles they break. This weight relationship is usually in excess of 100: 1. The sustained fall of the grinding bodies is obtained by placing them, together with the rock particles they grind, in a rotating drum or cylinder with horizontal axis, called a tumbling mill. The mill is nearly half full of grinding bodies and ore particles, which may be fed into one end and exit from the other through hollow trunnions which usually serve as the mill bearings. The mill lining must be thick to absorb wear and rough to prevent excessive slippage of the charge. The breakage of brittle rock or ore is accomplished by compression. The compression may be a rapid impact, from the fall and roll of a grinding ball, or it may result from the relatively slow and constrained motion as in a jaw crusher. Breakage by shear is a secondary result of the compressive motion. Ordinary rock has an extremely heterogenous structure with innumerable zones of weakness in which cracks, fractures, and breakages can form. When a rock is subjected to com¬pression it deforms. If the compressive force exceeds a certain critical value an incipient crack appears in the most fragile zones of weakness. This crack tip may first form on the particle surface or in its interior. When the first crack tip forms the compressive stresses immediately surrounding it flow to it, and this concentration of forces extends the crack and splits the rock. Other adjacent cracks may form during this extremely rapid process. Because of the nature of brittle particles, the work done in breaking them consists essentially of the work input required to compress them to the point at which the first crack tip forms. Breakage requires no appreciable additional energy input be¬yond that required for the deformation, since the stress energy already imported to the rock flows to the crack tip and extends it to breakage. Types of Tumbling Mills The general term tumbling mill includes the rod mill, ball mill, pebble mill, autogenous mill, and tube mill. It is of cylindrical or cylindro-conical shape and rotates about its horizontal axis. Rotational speed, liner type, and size and shape of tumbling media are selected to provide the desired operating conditions for the specific grinding application. Openings are provided through the mill ends for feed and discharge of the material being ground. A common feature of tumbling mills is the use of tumbling media

Jan 1, 1985

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-&apos;, a lo-&apos;-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10&apos; cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell&apos;s law that where = critical angle, n - index of refraction of air, n&apos; - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,&apos; and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert&apos;s law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By B Lavin, R Sanford

This paper examines the application of Lean Manufacturing in a mining environment, based on experience within the Rio Tinto entities: Rio Tinto Aluminium, Northparkes Mines and Hunter Valley Operations. The three applications have tested the flexibility of the Lean methodology. Within Rio Tinto, Rio Tinto Aluminium was the first group to introduce Lean. The rollout began in late 2004. It was introduced firstly at Boyne Smelters, Gladstone, as a model site with the initial application in the Carbon Bake Furnace area. It was later extended to other sites including the Weipa Bauxite Mine. LeanÆs successful application within Rio Tinto Aluminium was in part responsible for its recent adoption by other Australian-based Rio Tinto business units including Northparkes Mines, a copper mining operation in Central New South Wales, and Hunter Valley Operations, a group of four coal mines in the Hunter Valley region of New South Wales. Lean is also being adopted by Rio Tinto Iron Ore. Rio Tinto Aluminium introduced Lean Manufacturing to complement an existing Six Sigma business improvement program and to achieve continuous improvement activities at a workplace level. Lean provides a similar level of rigour and discipline to Six Sigma but its application is everyday and for everyone, everywhere in the workplace. It is a valuable management tool. In a short time, Lean has achieved good and sometimes spectacular results improving productivity and efficiency at all sites, including our mining site. Within Rio Tinto Aluminium, it has also had beneficial impacts on our ability to develop and retain employees.

Jan 1, 2006

By W. C. Elmore

THE magnetic powder method, long used. for roughly mapping mag-netic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter&apos;s original technique, with slight modifications, to study the varia-tion of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing con-siderable light on the magnetic secondary structure of alpha iron4 and of nickels single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure.

Jan 1, 1936

By B. M. Larsen

Attempting to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic" and "macroscopic," depending on whether the variations in concentration of solutes or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also untlerly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all sepregation effects. Undercooling and Nuclei Formation It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus temperature. In practical terms this means that the nuclei number illcreases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. Temperature Gradients and Heat Dissipation during Freezing Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period. Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1945

By David H. Davis, John Griffen

Much of the ground to be covered by this paper was ably covered by a paper presented by Messrs. Morrow and Jordan1 before a joint meeting of the Iron and Steel Section of the Engineers Society of West-ern Pennsylvania and the A.I.M.E. Pitts-burgh Section at Pittsburgh in the spring of 1940. As that paper was not published, the present authors have availed them-selves of Mr. Morrow&apos;s kind permission to use information given therein. Similar figures for the latest years available have been added to many statistics originally presented. It is unfortunate that Mr. Jordan&apos;s death removes his stimulating guidance and help, which the authors would have welcomed and have found invaluable in the past. One interested in the Pittsburgh seam should not fail to read the exhaustive and authoritative paper by Eavenson2 presented in 1938. As Allegheny, Fayette, Greene, Washington, and Westmoreland Counties contain practically all the reserves and furnish nearly all of the production from the Pittsburgh seam in Pennsylvania at the present time, this area only is intended when reference is made to the Pittsburgh seam in Pennsylvania. On much of the seam in Greene and Washington Counties, which contain a large proportion of the total reserves, insufficient data are available to determine the detailed characteristics of the seam with any degree of finality. It is hoped that the data presented here will fairly well indicate the probable characteristics. Economic Importance of the Pittsburgh Seam The Pittsburgh seam in Pennsylvania is of primary importance as a coal resource, not only because of its substantial reserves but because it contributes such a large proportion of the coal used in the country and an even larger proportion of that used in the manufacture of coke. Mr. Ashley3 placed the estimated recoverable reserves (1935) of the Pittsburgh coal bed in Pennsylvania at 7,500,000,000 tons.* Although a considerable portion of this tonnage is not now suitable for coking coal, because of its high sulphur content, undoubtedly the supply of coking coal will last for many years and that not suitable for coking will furnish industry with an ample supply of energy. In attempting to assess the contribution of the Pittsburgh seam to total coal production and to that of coal used in making coke, one finds that the statistics published annually by the U. S. Bureau of Mines, Minerals Yearbook, do not give tonnages classified as to seams but only as to districts or states and counties. However, it happens that, at present and during much of the

Jan 1, 1944