Search Documents

By J. Stachulak

In recent years more emphasis has been placed on the control of nitrogen dioxide (NO2) emissions from mining diesel equipment. Worldwide, diesel engine regulations to control emission and protect the environment are also driving the development of the diesel engine technology to reduce oxides of nitrogen NOx (Nitric oxide, NO + NO2). NOx are toxic gases produced in mines during the operation of diesel equipment. Most of the diesel equipment used in underground operations are equipped with Diesel Oxidization Catalysts (DOCs) designed to reduce carbon monoxide (CO) and hydrocarbons (HC). The effects of DOCs on NO2 production from diesel powered equipment is not well understood. DOCs do not alter NOx concentration, but may promote the oxidization of engine exhaust NO to the more toxic NO2, thus increasing the undesirable NO2 exposure of workers in the mine environment. In 2012, the ACGIH reduced the NO2 TLV concentration value from 3 ppm to 0.2 ppm. Vale and CanmetMINING have been involved in several research projects to reduce diesel emissions exposure to workers. One aspect of the current program is to determine the effects of in-use DOCs on NO2 production. Several in-use DOCs taken from mining equipment were selected for testing in the laboratory using ISO 8178-C1 and mine LHD transient test cycles. The paper presents the laboratory test results and effects of DOCs on NO2 production. The results indicate significant reductions in CO concentration, by over 77%, while increases in NO2 varied from 46% to 315% based on the ISO 8178-C1 8-mode steady state test cycle. The mine LHD transient test cycle showed the same pattern, although the magnitude of CO reduction was less. Consequently, it is recommended the use of only those DOCs that have been properly evaluated and shown not to significantly increase NO2 emission in the environment be used on mine equipment.

Aug 1, 2013

By Emily Johnson, Catherine Johnson, Ben Sonpon, Kelly Williams

The effect of length to diameter of the detonator is compared using Ansys/Autodyn 2-D simulations, the results of which are validated experimentally. It was found that higher pressure comes with a larger diameter, because it will result in more explosive energy being allocated out the end of the detonator.

Feb 1, 2020

By Clarissa Aguiar, Seok hyeon Chai, Thamer Yacoub, Sina Javankhoshdel

Sheet piles are used as an excavation support for soil retention. They are interlocked systems to form a wall for earth support along with anchors to provide an extra lateral support in excavations. The earth pressure against a sheet pile structure is not unique for each soil, but rather a function of soil-structure system. Movements of the structure with respect to the soil are primary factor in developing the pressure and thus the problem becomes indeterminate. In order to model a sheet pile wall for the analysis, structural element/interface can be used for the sheet pile. However, the use of the structural element with soil model alone is insufficient to simulate this soil-structure system as it fails to capture the slip condition between the sheet pile and the retained soil. In order to capture this slip condition, an interactive element can be used between sheet pile and soil to allow slip to occur. There have been many case studies where this method was used to analyze the response of the retained soil. Numerical studies have shown a good agreement with experimental results, but this stiffness is often not a well-known parameter, due to its complexity in nature of interactive behavior between soil and sheet pile walls. Also, many case studies are carried out with twodimensional analysis of the foundation, where three-dimensional analysis may be more suitable in some practical applications. In this paper, the interactive behavior of the element between sheet pile and soil is investigated with case studies for staged excavation using sheet piles and anchors. Then, investigation of a three-dimensional model is carried out by comparing with two-dimensional analysis.

By Thomas O. Ziebold, Robert E. Ogilvie

Experimental analysis of diffusion samples covering the entire Cu-Ag-Au system at 725°C has been carried out. Experimental coefficients are computed at twenty-eight points in the lermary system. It is found that the direct coefficienl for copper is nearly independent of the silver, content for 1ow-silver alloys and that the cross coefficient for silver correlates with the ther-nzodynatnic properlies. This lalter observalion leads to the conclusion that the mobililies of copper and gold are nearly equal. Thermodynarmic actiuilies for Cu-Ag-Au were computed from binary data and adjusted to be consistent with neasured tie lines across the two-phase region which extends into the ternary diagram at 725°C. Application of these therknodynarnic calculaliorls to the dijftcsion data terifies the Onsager reciprocal relations to the extent that experimental uncertainlies will allow. It is jound that diffusion neav the critical point of the 1200-phase field in the isothermal section at 725°C causes the composition gradients for copper and silver to approach infinity while the direct and cross coeficients become equal. From the standpoint of experimental Procedures, it has been shown that microanalysis of ternary samples may be carried out using a simple expression for the conversion of X-ray zntensily to composilion. The accuracy of' this method has been demonstrated by the analysis of standard alloys and by the reproducibility of composition determinations using differed X-ray lines. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. When only two elements are present there is just one independent composition variable, and the diffusion profile of composition vs distance across a sample must change monotonically through all solid solutions bracketed by the terminal alloys. If two-phase regions are stable for compositions between the terminal values, these must appear as planar interfaces in the diffused sample, with the composition profile exhibiting sharp discontinuities. Adding a third element may alter this picture completely. Because of the additional degree of freedom in the composition, we may see composition profiles which do not change monotonically through solid-solution ranges, and stable, nonplanar phase interfaces. Even though two-phase regions may lie between the terminal compositions of a diffusion sample on the constitution diagram, they will not necessarily appear in the diffusion profiles. In binary diffusion only one coefficient is needed to describe the interdiffusion process. From Fick's law this coefficient relates the diffusive flux of one component to its own composition gradient. In ternary diffusion we must allow for cross interaction between the two independent species. By a linear extension of Fick's law we introduce "cross" or "off-diagonal" diffusion coefficients which relate the flux of one component to the composition gradient of the other independent constituent. Thus, we require four interdiffusion coefficients to describe the transport process in a ternary system. In its most general form,1,2 the rate equation for mass transport by isothermal diffusion in a system of s components states that the diffusive flux of component i, Ji, is a linear summation of all driving forces, Xk, each force being multiplied by an appropriate compliance coefficient:

Jan 1, 1968

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

Outline ?Red Lake Gold Mines ?Red Lake Seismic System ?Applications of Seismic System at Red Lake Mine ?Seismic System Analysis and Customization ?Seismic Software ?Array Design ?Calibration and Source Mechanism ?Auto Picking Optimization ?Acquisition Groups ?Conclusions Goldcorp?s Red Lake Gold Mines ?One of the largest gold producers in Canada ?The operations comprise the former Campbell and Red Lake underground mines, now integrated as the Red Lake Gold Mines (RLGM) ?There are a total of 4 shafts with one internal winze and two main declines beginning at the 21st level ?Daily production approximately 2,600 tons

Aug 1, 2013

By H. Kahata, I. Iwasaki, Y. Takahasi

A combined process of segregation roasting-flota-tion or magnetic separation was developed to recover nickel from lateritic iron ores and oxidized nickel ores. An ore was mixed with a halide, such as sodium or calcium chloride, and a solid reductant, and roasted, whereby the nickel content was segregated out as discrete metallic particles. Either by magnetic separation, or by flotation using a sulfhydryl collector together with a heavy metal salt as an activator, the metallic nickel could be concentrated, Effects of such variables as the types and amounts of the halide and solid reductant addition and of the roasting conditions were extensively investigated. The concentration results on several types of ores from Japan, the Philippines, and New Caledonia are presented. Laterite is a residual product of rock decay in tropical and subtropical regions, and consists mainly of hydrated oxides of iron and alumina. Those derived from serpentine sometimes become enriched in nickel, cobalt, and chromium contents. Oxidized nickel ores are of the similar origin, but their nickel as well as silica contents are higher due to gamierite-type silicates. Apparently, nickel enrichment is more pronounced in the transition region between the surface layer of iron laterite and the underlying serpentine. Iron laterites often contain over 50% iron, and their reserve is reported to exceed 22 billion tons, corresponding approximately to 20% of the world iron ore reserve.1 It is readily apparent, therefore, why the iron laterites have attracted much attention of the steel industry as a potential source of iron ores. Numerous attempts to remove nickel and chromium as byproducts, have been reported in literature.' Worldwide discoveries of high-grade iron ore deposits in recent years have inevitably lessened the interests in iron laterites. However, in view of the tremendous potential for their gross value and supplies of nickel, cobalt, chromium, and alumina along with iron, the problem remains as a challenge. Much of the chromium in laterites is present in the form of relatively coarse particles of chromite, and various classification methods have successfully been applied for its removal.2,3 The nickel, however, is intimately associated with limonite, and ordinary concentration techniques are totally ineffective. Much attention has, therefore, been given to hydro-metallurgical or pyrometallurgical means. Yet, all the known processes appear to have limitations either economically or for the use of products as iron raw materials due to a high residual content of nickel. Some attempts have been made to pre-roast laterites or oxidized nickel ores, particularly with sulfidizing agents, and to remove nickel either by magnetic separation,' or by flotation.4 It is apparent that any such concentration process would require grain growth of nickel during roasting for effective separation. Oxidized copper ores are reported to be concentrated by the segregation roasting-flotation process,5 in which the ores are roasted with a chloridizing agent and a carbonaceous reductant in order to promote the growth of metallic copper through repeated cycles of copper chloride volatilization and its reduction on the solid reductant surfaces. Examination of a vapor pressure-temperature diagram of various metal chlorides indicates that a separation of nickel from iron may be effected by a similar process. In fact, the segregation roasting of laterites was reported to increase the extraction of nickel by the ammonia leach process, as compared to the ordinary reduction roasting.6 In the present article some of the preliminary experimental results of the segregation roasting, followed by either flotation or magnetic separation, on laterites and oxidized nickel ores are reported. The effects of various parameters in the roasting as well as in the concentration steps are discussed. MATERIALS AND METHODS An oxidized nickel ore from Thio, New Caledonia, and three laterites from Homonhon, the Philippines, Wakasa and Miyagawa, Japan, were selected for the

Jan 1, 1967

By W. H. Bassett

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. It is suggested that the material is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the sheet. FIGURES 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this? paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent.

Jan 2, 1926

By Richard L. Bullock, Bruce Kennedy

Vince Lombardi once said, "Practice doesn't make perfect, perfect practice makes perfect." When it comes to building a mine that will operate at the optimum level for the set of geologic conditions from which it was developed, Lombardi's remark might be paraphrased to describe the problem: planning won't guarantee the best possible mine operation unless it is the best possible mine planning. Any sacrifice in the best possible mine planning introduces the risk that the end results may not reach the optimum mine operation desired. This section addresses many of the factors to be considered in the initial phase of mine planning. These factors have the determining influence on the mining method, the size of the operation, the size of the mine openings, the mine productivity, the mine cost, and, eventually, the economic parameters used to determine whether or not the mineral reserve even should be developed. A little-known fact, even within the metal-mining community, is that room-and-pillar mining accounts for most of the underground mining in the united States. According to a 1973 study on noncoal mining (Anon., 1974), more than 76% of the producing mines [of over 1089 t/d (1200 stpd) capacity] produced approximately 70 000 000 t (77,000,000 st) or 60% of the nation's underground tonnage of material by room-and-pillar mining. That same year, 96.8% of the nation's under- ground coal mines produced 262 950 000 t (289,911,000 st) of coal extracted from room-and-pillar mines (Anon., 1976). Thus, nearly 333 000 000 t (367,000,000 st) of the United States' raw material is produced from mines using some form of the room-and-pillar mining system. Because approximately 90% of all mining in the United States is done by some variation of room-and- pillar mining, it is appropriate to give special emphasis to the effects of the various elements of mine planning on room-and-pillar mining. The relationship of these elements to other mining methods will become apparent as the elements are described in later sections herein. TECHNICAL INFORMATION NEEDED FOR PRELIMINARY MINE PLANNING Assuming that the reserve to be mined has been delineated with diamond-drill holes, the items listed in the following paragraphs need to be established with respect to mine planning for the mineralized material. Geologic and Mineralogic Information The geologic and mineralogic information needed includes the following: 1) The size (length, width, and thickness) of the areas to be mined within the overall area to be considered, including multiple areas, zones, or seams. 2) The dip or plunge of each mineralized zone, area, or seam, noting the maximum depth to be mined. 3) The continuity or discontinuity within each of the mineralized zones. 4) Any swelling or narrowing of each mineralized zone. 5) The sharpness between the grades of mineralized zones within the material considered economically minable. 6) The sharpness between the ore and waste cutoff, including whether this cutoff can be determined by observation or must be determined by assay or some special tool; whether this cutoff also serves as a natural parting resulting in little or no dilution, or whether the break between ore and waste must be induced entirely by the mining method; and whether or not the mineralized zone beyond (above or below) the existing cutoff represents submarginal economic value that may be- come economical at a later time. *7) The distribution of various valuable minerals making up each of the minable areas. 8) The distribution of the various deleterious minerals that may be harmful in processing the valuable mineral. 9) Whether or not the identified valuable minerals are interlocked with other fine-grained mineral or waste material. 10) The presence of alteration zones in both the mineralized and the waste zones. Structural Information (Physical and Chemical) The needed structural information includes the following: * 1 ) The depth of cover. 2) A detailed description of the cover including: the type of cover; * the structural features in relation to the mineralized zone; * the structural features in relation to the proposed mine development; and * the presence of and information about water, gas, or oil that may be encountered. 3) The structure of the host rock (back, floor, hanging wall, footwall, etc.), including: * the type of rock; * the approximate strength or range of strengths; * any noted weakening structures; * any noted zones of inherent high stress; noted zones of alteration; the porosity and permeability; * the presence of any swelling- clay or shale interbedding; the rock quality designation (RQD) throughout the various zones in and around all of the mineralized area to be mined out; the temperature of the zones proposed for mining; and the acid generating nature of the host rock. 4) The structure of the mineralized material, including all of the factors in item 3 plus: * the tendency of the mineral to change character after being broken, i.e., oxidizing, degenerating to all fines, recompacting into a solid mass, becoming fluid, etc.; * the siliceous content of the ore; the fibrous content of the ore; and the acid generating nature of the ore. Economic Information The needed economic information includes: *1) The tons of the mineral reserve at various

Jan 1, 1982

By Janet Briggs, Michael Vertes, J. F. Shirley, R. E. Cutherbertson, Alexander Sutulov, J. D. Vincent

Molybdenum, the 42nd element in the periodic table, is now a very important metal in industry of the United States and the world. Chemically, it is a very complex element having valences of 0, +2, +3, +4, +5, and +6, and can exist as a mixture of these valences in many compounds. It was discovered and separated by Scheele in 1778. At the present time, molybdenite is the only important commercial source of molybdenum. Molybdenum occurs in some 12-14 different recognized minerals, but practically all of the production is molybde¬nite. As late as 1915, it was considered a rare metal. Germany made extensive use of it during the first world war, which resulted in the establishment of a molybdenum industry in the United States at Cli¬max, Colo., in 1917. It was not until the mid-1920s when its introduc¬tion to steelmaking developed for the US automobile industry that the metal gained important acceptance. The first notable example was the Willis-Saint Claire automobile introduced in 1921 by C. Harold Willis, formerly chief metallurgist for Ford Motor Co. Molybdenum has also been produced in the US from wulfenite (PbMoO4) from Arizona and Nevada, and a small amount of molyb¬denite was produced up to the early 1970s as a coproduct from two molybdenum-bismuth mines in Quebec, Canada. The first byproduct production of molybdenite from a copper con¬centrating operation was achieved at Cananea, Sonora, Mexico, and was followed shortly by the Utah division of Kennecott Copper Co. in the mid-1930s. This section of the Handbook is divided into four main subdivi¬sions: Chapter 2, which deals with the concentration and recovery of molybdenite from primary molybdenum ores; Chapter 3, which deals with the recovery and separation of molybdenite as a byproduct from copper production; Chapter 4, which deals with the conversion practices employed for converting molybdenite to the oxide or metal form; and Chapter 5, which covers the uses of molybdenum in steel¬making, chemicals, pigments, lubrication, catalysts, etc. The Free World molybdenum production, for the past eight years from all sources, is shown in Table 1. 2. Primary Molybdenite Ores General In 1978 there were four primary molybdenite recovery plants in operation: Climax, Endako, Quests, and Henderson. For over half a century the Climax mine has been by far the largest and most important source of molybdenum in the world. During the early 1970s a few primary molybdenite mines in British Columbia were shut down due to adverse economical conditions. The largest of these was British Columbia Molybdenum, formerly owned by Kennecott Copper Corp. The Climax plant and operations are described in detail and the opera¬tions of the other plants are summarized following a general discussion of recovering molybdenite from primarily molybdenite ores. Recovery of molybdenite as a byproduct will be taken up in Chapter 3. Geology Molybdenite production from mines in which it is the sole or preponderantly important mineral is confined to ore bodies in granites or igneous-type rocks or pegmatite dikes. More than one state of mineralization is sometimes present as at Climax, York, Hardy, and Questa. In the case of Climax, important byproduct recovery of tung¬sten, tin, pyrite, and monazite is also attained. The molybdenite is commonly disseminated very finely in the siliceous granitic gangue but does occur in stringers and blebs in silicified mineral solution channels. Treatment of Primary Molybdenum Ores All primary molybdenum ores are low in molybdenite, the content ranging from less than 0.20% MoS2 to a high of about 0.40% MoS2. A high resistance to grinding is a common ore characteristic combined with a habit of very fine dissemination of molybdenite in the siliceous portion of the ore. Because of low MoS2 content, high hardness, and fine dissemination of molybdenite in primary ores, it has been necessary to develop a special mill treatment which yields an accepta¬ble recovery at a reasonably low milling cost. Essentially, the treatment consists of intensive rougher flotation at a relatively coarse grind with production of a low grade rougher froth containing a substantial percentage of the molybdenite in the form of low grade middling particles, followed with multistage regrinding to liberate the locked molybdenite and several stages of flotation cleaning to produce a finished grade concentrate. Rougher flotation on pulp ground to ap¬proximately 35 mesh is common practice, even if complete liberation of molybdenite from siliceous gangue may require regrinding to 200 mesh. The flotation of middling particles with a very low content of molybdenite in the rougher flotation step has been made possible by the application of a combination of reagents first developed at the Climax mill and used with some modification in the treatment of all primary molybdenum ores. The reagents commonly employed and their functions in flotation are:

Jan 1, 1985

By C. van Dijk

In Sept., 1960, a steam-drive project was started in the solution-gas drive area of the Schoonebeek field. A part(ern of three five-spots and one four-spot was selected covering an area of 65 acres. The pay in the project area has good lateral continuity and dips slightly to the northeut; it is about SO ft thick and permeability increases from 1,000 and at the bottom to approximately 10,000 md at the top. The oil originally in place was 12.6 X 10' bbl. The oil has an in situ viscosity of about 180 cp. At the start of the steam drive the cumulative primary production due to. solution-ga.7 drive amounted id 4 Percent of the oil originally in place. Reservoir pressure had dropped about 120 psi and no significant primary re-.serves remained. Some 11.3 million bbl of steam (all steam quantities are expressed in barrels of water vaporized) have been injected, resulting in production of an additional 4.1 X I0 9bl of oil, or 33 percent of the oil originally in place. This corresponds to a cumulative oil-stearn rario of 0.37 bbllbbl. It appears that the steam preferentially moves r updip while liquids are produced mainly from downdip wells observations indicate that tile steam flows through only the upper part of the formation. The lateral steam distribution in the pattern is satisfacrory since several prodriction wells hardly reacted and, hence, cori tributcd little to the oil production. Production performance and results from material balance calcutlations agree satisfactorily with the results of large-,scale laboratory experiments. On the basis of these experirmental results the .steam drive, together with a cold water follow-up. is expected to bring ultimate recovery to a value of crt leas: 50 percent of the oil originally in place. No serious production problems have been encountered. However, due to mechanical fuilure, two old prodriction wells and one injection well had to be replaced. An extension of the. steam drive in this area is under connstruction. Introduction The Schoonebeek oil field, discovered in 1943 and developed after World War 11, is situated in the eastern part of the Netherlands. The main oil reservoir in this field is the Valanginian sand. A completely sealing fault divides this reservoir into two areas (Fig. 1): the southwestern part of the sand body where primary production is ob- tained by means of a solution-gas drive, and the remain. der where edge-water drive is the production mechanism. In the greater part of the field the reservoir consists of a single, unconsolidated sand body. The net thickness ranges from 30 to 100 ft and the top is between 2,400 and 2,800 ft below sea level. Formation permeability varies from approximately 10,000 md at the top to values of the order of 1,000 md at the bottom, and porosity is about 30 percent. The reservoir contains a paraffinic oil of 25" API gravity with an in situ viscosity of 160 to 180 cp. Initial oil saturation was high (85 to 90 percent). The relatively large quantity of oil in place (more than 10' bbl), and the low ultimate primary recoveries expected from this field — approximately 15 percent stock-tank oil initially in place (STOIIP) for the water-drive area and 5 percent STOIIP for the solution-gas drive area — clearly indicate ample scope for secondary recovery. Because ies-ervoir and crude characteristics made this field suitable for thermal secondary recovery, a hot-water drive project was started in the water-drive area about 10 years ago. A few years later a steam drive and an in situ combustion project were started in the solution-gas drive area. This paper deals with the performance of the steam-drive project, which was started in Sept., 1960, and which is still in operation. Design of Steam-Drive Project, An experimental investigation of the steam-drive process carried out by schenk in 19561 indicated that under schoonebeek conditions steam injection could be an attractive secondary recovery method. the findings and encouraging results of a pilot test in the Mene Grande field in venezuela,i led to the design of a steam-drive project in the schoonebeek field, Pruject Site and Pattern In 1958 the reservoir pressure in the solution-gas drive area had decreased to about 120 psi, and oil production rates of wells in this area had dropped to 7 to 10 B/D. The cumulative primary production was about 4 percent STOIIP, leaving an oil saturation of approximately 85 percent. In view of the large amount of oil left behind in the reservoir, the solution-gas drive area was selected for the planned steam-drive project. The area in the vicinity of Well S1 3 (Fig. 2) was considered to be suitable since it is at least partly isolated from the rest of the field by faults and the sand is relatively thick (about 80 ft).

Jan 1, 1969

By A. M. Gaudin

THE study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a, substantially definite size which depends upon the ball size 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with-all the crushers tested. 7. Different methods of crushing produce grains of different shapes.

Jan 2, 1926

By P. G. Shewmon, H. E. Collins

A study has been made to determine the sites at which sulfur adsorption occurs on copper surfaces. measurements were made of the relative torques, Ys, at the intersection of twin boundaries with surfaces near the three low-index orientations, i.e., (100), @lo), and 011), over a range of H2S/H2 ratios. HZS concerztvations j'ro~n 3 to 1500pp)n between 830" and 1050°C were used. It is concluded that sulfur adsorption occurved preferentially though not exclusively at edge sites near the (100) and (110) surfaces in the HzS range — 700 Ppm giving rise to negative torques near these orientations. Beyond this HzS range, adsorption occurred at all sites. Near the (111) surface, 7/y little with HzS concentration up to approxiwzately 75pptn. Above this range, the results indicate adsorption is occurring OH both terrace and edge sites. SCIENTIFIC interest in surfaces and their interactions with a gaseous environment dates back to the beginning of the 19th century. The scientific luminaries of that period—Faraday, Maxwell, Rayleigh, Dewar, and Gibbs—were already concerned about such processes. However, it has only been within the past several decades that adsorption on metal surfaces has been actively studied. This increased interest in adsorption has been brought about by the advent of new and improved experimental techniques and apparatus, e.g., ultrahigh vacuum, and field-emission and ion microscopes. However, most of the work done using these techniques has been carried out at low temperatures. When adsorption studies have been made at either low or high temperatures, they usually gave no indication of the particular surface orientations or type of sites on which adsorption was occurring. In the last few years, there have been a series of studies in which the surface tension, y,, and/or its derivative with respect to orientation, 7, have been studied as a function of orientation and atmosphere.'-7 Nearly all of the work on the relative torque,* ~/y, silver annealed in hydrogen and air.6 Recently Winterbottom and Gjostein" have used a modified and more accurate Mykurian method to determine the y plot of gold in hydrogen The only work in which T/~, has been measured over a range of chemical potentials for a given solute, p2, is that of Robertson and shewmon7 on the Cu-0 system. They measured T/Y, vs Po, (10"" to 10- l3 atm) at 1000°C in various mixtures of Hz0 and HZ. From this work they estimated the value of p2 at which one half of the surface sites are occupied with oxygen, pg, as being in the range 10- l6 to 10- l5 atm of oxygen. They also found that increasing Pa increased the magnitude of ~/y, near the (111) and (100) orientations. This indicates that oxygen is not adsorbed preferentially at step edges, but uniformly over all surface sites. In addition, they did one experiment on sulfur adsorption on copper surfaces, which indicated that sulfur adsorption decreases ~/y, near the (100) orientation, while not affecting ~/y, near the (111). This could be interpreted as indicating that sulfur adsorbs preferentially at step edges near the (100). In this paper the primary objective of the work has been to carry out a study of sulfur adsorption on copper surfaces over a range of temperatures and p,. In conjunction with this work, thermal grooving at grain boundaries has been examined as a method of determining the effect of sulfur adsorption on y,. METHODS Ideally, one would like to have information on the quantity of solute adsorbed on a surface and the types of sites at which it is absorbed as a function of p2. The total quantity adsorbed or the surface excess is given by the thermodynamic equation Thus data on the variation of y, with pz indicates the value of p2 at which adsorption becomes appreciable and the quantity adsorbed. The type of adsorption site is more difficult to deduce but information on this can be obtained from the variation of rz with 8, the angular deviation of the surface orientation. This is obtained from the thermodynamic equationlg Data on t and ys as functions of p2 have been obtained by the following methods. 1) Twin Boundary Grooving—By determining the effect of adsorption on the torque, 7, where T is the variation of surface energy, y,, with orientation, it is possible to obtain some indication as to the preferred sites of adsorption. Experimentally, the torque value measured is the relative torque, 7/ys The twin boundary grooving technique suggested by Mykura'' was used in this study to determine near the three low-index orientations— (loo), (110), and (111). Mykura's equation relates 7 /yS to measurements of the di-

Jan 1, 1967

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment, these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In U.S. Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center's 900-lb per hr pilot plant, approximately 85% of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to 51000 ppm equivalent SiO*, while maintaining a Ca(II) content of =16 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water. Water quality is perhaps as important to flotation as are the reagents used. The character of water is extremely variable, depending on whether the source is a well, lake, or stream, upon the season and temperature, upon prior use, and upon the character of the watershed. All of these factors influence the water hardness and the quantity of other dissolved inorganic salts, turbidity, dissolved and suspended organic matter, dissolved gases, and pH. Frequently, the differences in water quality can measurably influence flotation selectivity, often to the point of spelling success or failure. Water hardness is particularly troublesome in flotation systems employing fatty acids, but other unrecognized constituents may also contribute to peculiarities in flotation behavior. Furthermore, a given water source may be entirely satisfactory in one flotation system, but entirely inappropriate in another. In recent years, society has given more attention than formerly to water use, even in areas where water is plentiful. However, both the demands of a growing population, with increased per capita needs, and also those of industry must be met. As a result, riparian rights must be negotiated with the appropriate government agency or agencies so that consumption of water is often allocated or otherwise controlled. Furthermore, the disposal of off-process industrial and domestic water is coming under the increasing scrutiny of these same governmental units. In these respects, the mineral industry is no exception, so that conservation, water reclamation, and reuse may be expected to assume increasing importance. In 1932, it was stated that, "water reclamation is generally more expensive than the economy in water and reagents resulting from its use. It is employed only if it is urgent to save water."' The economic aspects of this statement may still be true, but the unrestricted use of water is becoming less and less an option of the user. The purpose of this paper is to discuss an investigation conducted by the U.S. Bureau of Mines (USBM), in which water reclamation and treatment were undertaken to develop procedures for, and to assess the effects of, water reuse on the flotation treatment of nonmagnetic taconites. This investigation is a logical extension of previous work described by the author and associates at the Twin Cities Metallurgy Research Center employing selective flocculation-desliming and anionic flotation of silica from low-grade, nonmagnetic iron ores2,8 The requirements for the selective flocculation-de-sliming and the anionic flotation of silica processes determined the direction of the investigation. Previous studies had indicated that pH levels of about 11.0 and 11.8 were required for selective flocculation and flota-tlon, respectively. The calcium content of the water was believed to be of importance in both of these operations, and since Minneapolis tap water with a Ca(I1) content of about 16 ppm had been successfully used, an attempt was made to reclaim the process water at an equal level of dissolved calcium. Additionally, the objective was to nullify or effectively limit the effects of dispersants and fatty acid residuals from prior stages of processing. Last but not least, the system of water treatment had to have the capability of reducing turbidities to workable levels. With about half of the effluent being derived from the selective flocculation-desliming step and carrying about 25,000 ppm of highly dispersed, suspended fines, this last objective appeared formidable at the outset. Procedures for water reclamation were derived, in part, from well-known mineral dressing practices, from past observations and investigations, and from concepts contained in various pertinent publications on water treatment."c These procedures involved: 1) flocculation with lime and poly electrolyte-type flocculants, 2) lime-soda-ash softening, 3) chemical precipitation, and 4) mineral surface adsorption. Control was exercised at various stages of water reclamation by frequent measurements of Ca(11), pH, and turbidity.

Jan 1, 1971

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

By J. Clair, H. Mirabel

The determination of the temperature and electrical potential distributicms in the cathodes of aluminum electrolytic cells is difficult. The reascms come from the various nature and the intricate three-dimensional geometry of the materials; besides thermal and electrical phenomena react upon each other. A method of calculation using a computer program applied to a mathematical model, figuring the cathode, is developed. Both of the thermal and electrical phenomena are simultaneously considered. Temperature and electrical potential distributions are finally obtained by successive iterations. Results are compared with measurements on industrial cells. Theoretical and practical applications of these studies are given. Up to the present time the study of the distribution of the temperatures and electric potentials in the electrodes, anode and cathode, of the electrolytic cells used for the production of aluminum was limited to one of the two aspects of the phenomena because of lack of a simultaneous method of calculation. For example, the anode or cathode drop was studied assuming that the temperatures in the iron and carbon are known, a method that obviously is very approximate since iron resistivity, in particular, greatly varies with temperature, which in turn depends on current density. Consequently we tried to find a method of calculation simultaneously taking into account both thermal and electrical phenomena. We proceeded to the study of the cathodes as an initial approach to the problem. Although the cathode and surrounding materials may have varied forms and particularly very heterogeneous characteristics, their structures are simpler than that of the Sijderberg anode and boundary conditions are more easily represented than in the case of anodes even though they are prebaked. The study was in two parts: a) development of a model schematizing the true geometry of a cathode and defining the thermal and electrical boundary conditions, and b) working out a method of calculation of the temperatures and potentials by means of an electronic computer. To facilitate solution of the problem, a model was used initially much simplified in comparison with an actual cathode. This model permitted development of the method of calculation. In a second phase, this model was adjusted to the study of actual cathodes and applied to different types of cells: low- or high-intensity cells, cells set up at ground level or above ground level, cells with cathodes more or less heat-insulated. Simultaneously measurements were made with cells equipped with cathodes of the types studied to compare the values resulting from calculation. The initial model was also used for general studies, in particular for studying the effects of current density in the carbon and iron. The results were confirmed or made precise by the model of the true cathodes. This report successively describes: a) the manner in which the model representing a cathode was worked out, with the simplifications and/or the hypotheses used, b) the method of solution of the problem by means of the electronic computer, and c) an example, stating the extent to which the results obtained may be realistic. Further the possibilities offered by such a study are examined. 1) CATHODE REPRESENTATION The purpose of this phase is to represent the cathode in the form of a so-called "mathematical model", that is with a simplified geometrical configuration, in order to meet the subsequent calculation requirements, while keeping to the true facts as closely as possible. This model further includes the thermal and electric conductivities with regard to temperature for the varied materials composing the cathode, as well as the thermal and electrical conditions at the model boundaries. 1.1) Guiding Principles. For calculating the temperatures and potentials the model is divided by trior-thogonal planes into a network of small elementary parallelepipeds. At the summit of these parallelepipeds' so-called mesh points, the temperatures and potentials are computed. The number of mesh points is of course limited by the capabilities of the computer, since 1) the number of equations to be solved depends on the number of mesh points selected, and 2) the amount of time spent by the computer considerably increases with increasing this number. These conditions call for the following requirements as concerns the model: a) Dimensional requirements: the calculation will be all the more accurate as the network is more closely meshed. Since the number of mesh points is limited in practice, it is necessary to restrict the dimensions of the model. b) Geometrical requirements: so as to make things easier in working out the network, the model must be given a simple geometry. In particular, it will be convenient to have the cathode so constituted that the surfaces limiting the cathode and the surfaces within the cathodes separating the different materials consist of triorthogonal planes. 1.2) Schematization of the Cathodes. After the tech-

Jan 1, 1968

By E. C. Truesdale

A FEW years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.2 During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. TABLE 1.-Typical Analyses Percentage by Weight Sum of Zinc Pb, Fe, Pb Fe Cd Al Cd Special High Grades 0.007b 0.005b 0.0056 none 0.0106 C.P. (chemically pure) <0.0002 0.0005° 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 6-37). b Maximum. c Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By G. F. Comstock

In the literature of metallography there is a large amount of material describing the various non-metallic inclusions found in iron and steel, and the appearance of sulfides, silicates, oxides, or alumina in steel under the microscope is fairly well known. The inclusions found in non-ferrous metals are, however, not so well known, at least judging from published writings, and the author has been interested in examining small castings of copper, brass, or bronze with certain inclusions purposely mixed with the metal, to see what was the characteristic appearance of each kind of inclusion, and if they could be readily distinguished from one another. The method employed in most cases consisted in overheating and oxidizing a small charge of copper, then cooling it somewhat, and adding a suitable amount of the element whose oxide it was desired to observe. This element was stirred in well and given time to react with the oxygen in the copper, then the melt was poured in a sand mold in the form of a cylinder about 21/2 in. (63 mm.) in each dimension, with a sprue about 11/2 in. (38 mm.) in diameter and 3 in. (76 mm.) high on top of the cylinder, the sprue forming the only riser. Samples for examination were cut sometimes from the center of the casting, and sometimes from the sprue or riser. A few of these samples were cast in chill molds. The appearance of sulfides was studied in an alloy containing 10 per cent, each of tin and lead, with which a flux of plaster of Paris was used. The appearance of foundry sand was studied in several alloys, one of them having sand stirred into the metal intentionally, and others having cut into the molds badly when poured, so that the castings were spoiled by included sand. As all this work was done on alloys having copper as the chief ingredient, the natural starting point was copper oxide, the appearance of which in a micro-section is well known. Cuprous oxide is soluble in molten copper, but separates out in freezing and forms a eutectic containing 3.5 per cent. Cu20, or 0.39 per cent. oxygen. If there is less

Jan 1, 1919

By H J. Ross, R K. Beatson, T J, W R. Fright

Traditional method of explicitly defining three-dimensional (3D) ore-waste and geological boundaries relies heavily on a time-consuming process of manual digitisation. This method of modelling can be best described as surface modelling, as complex surface geometry is built up by digitising points that lie on the surface. With the advent of fast 3D interpolation methods, however, construction of geological surfaces using volume functions is now a practical alternative to explicit modelling of surfaces. Unlike explicit modelling, surfaces contained in volume functions are not explicitly defined or digitised. Instead the existence of surfaces in the volume function is implicit, thus the process of modelling surfaces from volume function is called æimplicit modellingÆ. Based on recent advances in fast scattered data interpolation methods, implicit modelling first defines a continuous three-dimensional function that describes the grade or rock distribution. This volumetric function is interrogated for a grade value, or a geological surface, thus allowing the extraction of the 3D object to be automated and eliminating the need to manually digitise surfaces. Since the function is continuous throughout space and does not depend on a mesh or grid for its definition, the extracted geological or grade wireframes can be constructed at any desired resolution in the specific volume of interest. The volume modelling method can work on scattered drillhole data of any data density, including processing combined information from dense grade control data as well as sparse resource drilling. It offers distinct advantages over surface modelling, including: being able to wireframe geological objects that may take days to digitise in tens of minutes; substantial improvement in modelling accuracy; and the ability to generate conditional models rapidly allowing mining risks inherent in geological modelling to be examined.

Jan 1, 2003

By S. D. Strauss

The marketing of nonferrous metals and of the ores and concentrates from which these metals are recovered is a fascinating trade, international in character, sensitive to every change in the economic tide, and complex in its organization. Each individual metal has its own marketing mechanism; no two are exactly alike. The differences sometimes are a matter of tradition rather than of necessity, but usually they have developed because of the very nature of the problems of producing or consuming the individual metal. This description, because of limitations of space, can do no more than indicate the major aspects of the trade and touch lightly on the marketing structure of each metal. The dictionary states that a market is a "meeting of people for selling and buying." In the case of nonferrous metals this meeting may occur on a half-dozen different occasions between the time the ore has been first mined and the time the refined metal is available for use by industry; or it may not occur at all until after the metal itself has been rolled, drawn, stamped, cast, or forged into a useful semifabricated shape. To illustrate: A Chilean miner may sell his small ore production to a custom mill, which produces concentrates that are sold to an ore dealer, who finances shipments of the concentrate to a custom smelter, which buys them for conversion into blister, to be subsequently refined into electrolytic copper (sometimes by a refinery having no corporate ties with the custom smelter) and sold. Conversely, aluminum production is mostly by integrated concerns that mine bauxite, convert it to alumina, smelt that to produce aluminum, and then fabricate that into semifinished or even finished products before title to the material changes hands for the first time. Some nonferrous ores are not converted into metal at all but are sold by the miners or dealers directly to the ultimate consumers. A good example would be chrome ores used by the chemical industry. And of course a substantial part of the commerce in nonferrous metals is in scrap, which is the reconversion into useful form of metals that have long since been mined and smelted. Thus, one-third of all the lead used in the United

Jan 1, 1964