Search Documents

By W. T. Abel

The Bureau of Mines tested 48 materials for their ability to absorb H2S from hot simulated producer gas (1,000°-1,500° F). The material found best from the standpoint of absorption capacity, durability, and amenability to regeneration was sintered pellets of 75 percent fly ash-25 percent Fe203. The performance of this absorbent under simulated and actual conditions is described. The effect of absorbent composition, absorbent temperature, steam content of the gas, and tar vapors and dust in producer gas is discussed.

Jan 1, 1974

By Chowdhury P. J R, Biswas S. K

Recovery of metallic values from lean-grade raw materials as well as from secondary/intermediate industrial products is of immense importance to a country like India which is not endowed with extensive sources of copper and nickel. The results of a few studies carried out in this area are described in Part-I and Part-II in this article. A novel anode casting system, specially designed for a small copper refinery which had been set up to produce copper wire bars/rods is described briefly in Part-III.

Jan 1, 1992

By Ian W. Farmer

A description of the factors causing outbursts and rockbursts in coal mines is given. The mechanics of both outbursts and rockbursts can be described in terms of conversion of stored strain energy in the coal and surrounding rocks into kinetic energy through failure. The major difference between the two phenomena is that gases adsorbed onto the coal structure and desorbed during deformation contribute to the energy available during outbursts and may also affect the loading and unloading characteristics associated with failure. The amount of energy involved and the type of phenomenon are related principally to gas content depth and rock behavior.

Jan 1, 1988

By Denholm W. T, Rankin W. J

The reduction of zinc from lead blast furnace slags using hydrogen was studied at 1300¦C as part of a laboratory investigation of zinc fuming. To perform the experiments, 300 g "spent slag" was melted in a crucible. Hydrogen was then injected into the slag through a lance and fresh blast furnace slag was added regularly in small quantities over a period of 40 minutes. Zinc added in the fresh slag was reduced and the zinc level of the bulk slag attained a steady state value of between 1 and 9% after about 10 minutes, depending on the gas injection rate. Because of the high reactivity of hydrogen, bulk supply of hydrogen to the slag was the rate limiting step at the flow rates used and it is believed that the gas-slag reactions in the system were at equilibrium. A partially/stabilized zirconia cell with a Ni/NiO reference electrode was immersed in the slags during the experiments and the steady/state oxygen potentials of the slags were measured. By using the experimental oxygen potential values and calculated values of the steady state concentrations of zinc in the offgas, the activity of ZnO in the slags was calculated from the Gibbs's free energy change for the reaction:

Jan 1, 1989

By Donald E. Warnken

The Study concerns the estimation of fair market value (FMV) of non-producing mineral rights. Two approaches to value are used and the values determined by each are compared. The Study area environment is unusual. The tectonics is visible on surface rocks throughout much of the study area. The effect on mineral values in the exposed areas has been compared to areas where the tectonics is not visible.

Jan 1, 2005

By A T. Owen, F A. Benn, J D. Swift, D M. Labbett, A F. Grabsch

The AMIRA P266 æImproving Thickener TechnologyÆ series of projects has sought to provide a firm scientific basis for feedwell and thickener design, a requirement as pressures on water usage in the minerals industry increase. While advanced computational fluid dynamics modelling of feedwell processes has generated the most obvious and successful applications to improving the performance of operating units, such outcomes have drawn heavily on parallel studies into flocculation fundamentals. Central to this has been the development of a linear pipe reactor system that allows the kinetics of flocculated aggregate growth and rupture to be measured for thickener feeds under turbulent pipe flow conditions. This ensures much greater control of the intensity and duration of applied shear than is possible with conventional flocculation test procedures, offering insights into flocculation processes that would be otherwise hidden in time-averaged measurements.

Jan 1, 2009

By Ichinose M, Tsuru T, Gotoh K

Since 1980, the Department of Mining Engineering at Kyushu University, in co-operation with the Ikeshima Colliery, Matsushima Coal Mining Co. Ltd., has been conducting a research project into longwall gateroad designs applicable to deep and poor strata conditions. During this period, the economic environment has drastically changed the situation of the domestic coal mining industry. Conventionally, the retreat longwall method, with re-use of gateroad, has been employed as it achieves higher recovery. However, from the view point of production efficiency, this method is not suitable because it requires intensive work in side packing and roadway maintenance. Therefore an interpanel-pillar system, or a two-entry gateroad system, was adopted to identify the factors responsible for excessive vertical closure in longwall gateroads. Field measurements and non-linear finite element analyses were undertaken to confirm the performance of this system. Study results indicate that the stability of the gateroad employing the rib pillar system is comparable to that of the conventional system of re-using Gateroads.

Jan 1, 1992

By A. R. Barnes, R. Pandher, T. Shannon, P. Gover

Following the closure of the Glencore Zinc Brunswick mine, the Glencore Brunswick Smelter has transitioned to treating external feeds, and currently treats a number of secondary Pb-Zn concentrates. Processing these concentrates has in some cases been challenging due to the diverse mineralogy of the feeds. Certain feeds are difficult to ignite or show inadequate sulphur removal during oxidation on the sinter strand, while in other cases, combinations of feeds produce a sinter with unsuitable properties for further handling. This paper discusses two methods developed in collaboration with XPS Consulting & Testwork Services to characterize these feeds prior to processing them and to identify which ones are most likely to pose challenges during processing.

Jan 1, 2014

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are the most common steel-based ground reinforcement used in underground mines in Western Australia. As with any other steel-based product used in underground mines they are susceptible to corrosion, particularly under aggressive minewater and mineral conditions. Because of their thin-wall tubular construction and large surface area, the potential damage resulting from corrosion is considered to be more severe for this type of reinforcement than for other forms of reinforcement made of solid steel bars. Because of the obvious safety problems which may result from corrosion, both mine operators and regulators have raised concerns regarding the long-term effectiveness of FRS installed in underground mines in Western Australia. Although corrosion has been recognised as an important safety issue, the controls of corrosion in varied underground mining environments has not been well understood. To improve the understanding of the corrosion behaviour of FRS, the Department of Minerals and Energy has initiated a research project focused on the mechanisms and extent of corrosion attacks, and their influence on the effectiveness of the reinforcement. This paper describes the research project and presents the interim results achieved To-date.

Jan 1, 1995

By M. W. Fabjanczyk

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By R. W. Hill

Multiseam mining has been carried out at many collieries in South Africa. It the seams are In close proximity difficult and dangerous mining conditions may arise. In the Witbank area multiseam bord and pillar mining has been carried out, while in Natal where the seams are thinner and of a higher quality, total extraction methods are common. Several combinations of multiseam mining have been carried out. The paper highlights a number of case studies and the strata control problems that can arise.

Jan 1, 1995

BECAUSE of the attention given in recent years to the flotation process, there is an extensive range of equipment available to any staff detailed for: the design of a flotation mill. This statement applies not only to the flotation machines, but also to equipment for crushing and grinding, elevating the pulp, dehydrating of concentrates, and the methods of driving the various equipment.Distributed through the Proceedings and Transactions of various metallurgical societies and journals there are many excellent descriptions of flotation mills, their equipment and performance.Whilst these articles describe-in many cases in detail-the equipment in the mills to which they refer, the reasons which govern the choice of each particular equipment are not usually given.

Jan 1, 1929

By Cleghorn JH

Underground mining operations on Kalgoorlie's Golden Mile were suspended in 1976, suffering the combined effects of low gold prices and grades. A subsequent substantial increase in the gold price led to the decision by Kalgoorlie Mining Associates to reopen their mines in 1979. The two shafts selected for access required excessive maintenance. The geological assessment and development parameters prescribed have been successfully used to establish reserves to maintain production at a 390 000 tonnes per annum rate. While ore reserve grade is being maintained from primary stoping sources, supplementary lower grade ore is drawn from remnant pillars and stopes at lower cost.Performance by the workforce has reached levels previously attained and a record tonnage was hoisted in the fourth year after recommencement.Keywords : Golden Mile lodes, geological research, payruns, cut and fill, mill holes, gold price, ore grade, amalgamation.

Jan 1, 1984

By W. R. Hibbard

Pole figures, torque curves, and coercive force have been determined for the following rolled and annealed permanent magnet alloys: Cunife, Cunico, Silmanal, Vicalloy I, Vicalloy II, and Heusler's Alloy. IN the general category of precipitation-type permanent magnet alloys there is a group of ductile alloys, including Cunife, Cunico, Silmanal, Heusler's Alloy and Vicalloy, which can be extensively rolled and annealed to develop a preferred orientation in the crystals of the matrix material. The rolling and annealing textures of Cunifel and Vicalloy' have been previously investigated qualitatively, but no pole figures are available in the literature. In addition, the role of precipitation in these permanent magnet alloys is still somewhat controversial. It

Jan 1, 1957

NORTH AMERICA Number Members Alaska 31 Canada 302 Mexico 175 Newfoundland 3 United States Alabama 52 Arizona 131 Arkansas 9 California 723 Colorado 184 Connecticut 98 Delaware 19 District of Columbia 133 Florida 16 Georgia 6 Idaho 61 Illinois 241 Indiana 57 Iowa 7 Kansas 32 Kentucky 33

Jan 1, 1932

Situation Brands & Employment Value Propositions of mining sector firms are perceived negatively Competitive labour market is generally not aware of the diversity of mining careers Jobs requiring unique skills & experiences are no filled Traditional means of generating awareness to attract candidates is not aligned with how youth (for example) uses technology throughout the recruitment process Gobal economic downturn

May 1, 2009

By Walter Renton Ingalls

Vague references to tin-deposits in Mexico are scattered throughout technical literature, and that country has been looked to as a likely source of a part of the world's supply of till at no very distant date; but thus far nothing but occasional small lots have come forward, so that the notion has arisen that these mines are either mythical or unworkable. So far as I am aware, there has not yet been published any description of the tin-deposits of Mexico except a few brief references; and this paper, based on a study of them made in 1892, is therefore offered.

Jan 1, 1896