Search Documents

By Oscar Harder

IT is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing -his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treating high-speed steels. Regarding this research, Dr. Sauveur, (22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and. related materials in the red-heat range, using various methods. . The results, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as its immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978

By L. D. Clark

Pay-out, the ratio of capital expenditure to annual cash return can be very revealing when employed to gage the merits of a proposed mining venture. It is a quantity, numerically but not physically equal to a factor, by which cash return may be discounted to equal required investment. The fewer the pay-out years, the greater the average annual earning power of the project. Considerable material has been written in the past about the most important and difficult problem mining management faces in evaluation of a property: the optimum production rate for the venture. What daily capacity should be adopted for the proposed operation that it may be the most rewarding to those underwriting it? H.C. Hoover has said, "The most important objective is the least cost per ton mined; and minimum working costs can only be gained by the most intensive production." Theoretically and practically, the quicker the ore is removed, the more profitable should be the venture because of the saving in fixed charges, the consequent lower unit costs and the interest unearned by the profit from the unmined ore. Yet, such performance will be tempered by policy and a restraint imposed by the ratio of capital expenditure to annual cash return. * The 'Annual net profit after taxes but including depreciation and depletion allowances. former will be based upon an analysis of the economic climate anticipated, with its many ramifications including the demand for the product, prices, tax laws, the conduct of labor and related wage scales. The variables and intangibles involved in estimating the optimum production rate for a mine do not readily lend themselves to mathematical relationships or equations and the problem can become complex indeed. The more readily applicable and relatively faster appraisal method will be used which, in addition to being reasonably adequate in most cases, will serve as a guide, should a more expanded and detailed estimate be desired. The first question is what is company policy with respect to the rate of investment return? This will depend on that significant period of time referred to as the pay-out, which can be defined as the estimated interval during which capital investment is returned through application of annual cash return to its recovery. Expressed another way, it is the ratio of capital expenditure to the annual cash return. For example, if the capital investment is $C and the annual cash return is $A (after Federal tax), then $C/$A = the pay-out period in years. That is to say, if $C = $1,500,000 and $A = $214,000, then which is the mathematical expression for the period of time it takes to recover the funds originally invested in a mining enterprise. The relationship yp = $C/$A can be useful — an expression which requires only the significant tern yp to be fixed; in other words, the long range investment policy. For what is the pay-out period but an expression of that policy in terms of the speed, within practical limits, with which an individual or company may want to recover capital expenditure? A policy by which pay-out will be fixed is imperative. This ratio must lie within relatively narrow limits governed by what is economically feasible. It cannot be too low, rendering the ratio impractical or absurd, nor too great, delaying the return of capital for reinvestment beyond a commensurate interval. What pay-out will govern this policy? Federal corporate taxes would seem to present the best measure. Consider mining in Canada where new mines are exempt from Federal income tax for 3½ yr from date of first production. This exemption expressly allows The Act states: "A corporation . . . i s not required to include the profits . . . for the period of 36 months commencing with the day on which the mine came into production in reasonable commercial quantites." a company to recover capital expenditure during the early stages of production. With such an incentive, it is logical to strive for as much capital redemption as possible during this period. Thus, 3½ yr would be a major contribution to the pay-out in Canada. Furthermore, it generally takes from 1½ to 3 yr to develop

Jan 1, 1963

By R. G. L. McCready, R. O. van Everdingen, M. Kalin, R. van Everdingen

"This paper is based on data generated between October, 1986 and October, 1989, during the implementation of an Ecological Engineering close-out for a zinc mine in Northern Ontario, where 690000 tonnes of tailings contain 41.1% pyrite and 4.1% pyrrhotite. The objective was to determine rates of sulphide oxidation and iron precipitation in the tailings. Those rates are relevant for the assessment of the long-term effectiveness of biological systems employed in the removal of heavy metals from contaminated drainage issuing from tailings.Data were collected on the topography and stratigraphy of the tailings basin, subsurface temperatures and groundwater levels, and chemical analyses were made of water samples collected from a number of piezometers. The thickness of unsaturated tailings varied widely between individual piezometer locations; annual maxima ranged from 0.67 m to 3.55 m, and annual minima from 0 to 2.68 m. Sulphate concentrations ranged from 36 mg/L to 20180 mg/L; iron concentrations from 0.36 mg/L to 9938 mg/L; and zinc concentrations from 0.33 mg/L to 1123 mg/L.The geochemistry of the piezometer samples suggests that some of the initial Fe content, resulting from metal sulphide oxidation, is subsequently precipitated in the tailings pile and, possibly, in the underlying unconsolidated sediments, probably in the form of iron-hydroxide and Na-jarosite. Other metals such as Zn may be co-precipitated with Fe. The discharge of a portion of these metals to the environment would be delayed by this process. Some of the initial sulphate may also be lost from solution, probably by precipitation of gypsum; approximate saturation degrees for gypsum ranged from -3.27 to +0.47. The precipitated minerals will somewhat decrease the porosity and permeability of the tailings.Sulphide-oxidation rates, calculated using the analytical results and the estimated amount of annual recharge at the tailings site, average 0.0057 mol/kg/yr. Calculated iron-precipitation rates average 0.000386 mol/kg/yr. It is concluded that the characteristics of seepage from mining wastes may change with time, reflecting the solubilization of precipitated secondary minerals."

Jan 1, 1992

By T. F. McCormick

THIS year, 1950, is the golden anniversary of the construction and operation in this country of a tube mill for the sole purpose of fabricating aluminum alloy tubing. For a short period prior to the beginning of this mill, aluminum alloy tubing was obtained from foreign sources or produced in mills fabricating other metals. Indeed, it was a very short period because aluminum itself was a newcomer in the field of metals. The first sheet rolling mill had been in operation just eight years and a rod rolling mill for the production of wire and cable had been functioning one year. The first tube mill for aluminum was built by the Aluminum Co. of America in May 1900 and started production with four draw benches and five men, including the mill superintendent. The building itself was a lean-to attached to a sheet-rolling mill at New Kensington, Pa. The cost of equipment, including the draw benches, dies, mandrels, and other tools, was about $5000. This figure seems absurd in the present day but nevertheless it was questioned at that time whether or not such a large sum should be spent to embark on a new and uncertain venture. The initial production system for the new mill consisted of casting round hollow ingots in a tilting-type iron mold, reducing the ingots to bloom size outside the plant, and finally drawing to size on the draw benches. This method of producing aluminum alloy tubing survived just two years, as blooms of satisfactory quality were not obtained consistently. It was superseded by the cupping method in which a 24-in. diam circle cut from a rolled plate was formed into a tube bloom using first a small cupping press and then a push bench. It was stated that tubing so produced was limited to a maximum diameter of 2 3/4 in. and to wall thicknesses varying from 12 to 24 gage. However, for the first time all the operations were performed at one plant and the result was a quality product. Later larger cupping presses and push benches were obtained and the method continued to be the principal one for aluminum alloy tubing for almost a quarter of a century. During the interim the use of a Alan Mannesmann -type billet piercer was explored and it was used to some extent, but failed to produce consistently a smooth inside surface suitable for drawing with aluminum alloys. Experiments started during the latter stages of World War I in the production of tube blooms with a hydraulic extrusion press, led to the use of this type of equipment to make tube blooms for further drawing during a change-over period extending from 1925 until 1930. At this time the cupping method was discarded completely. From these humble beginnings, the aluminum alloy tubing business expanded until well over six million pounds were produced in a single month in the United States during World War II. The major portion of this production was in strong alloys which did not appear in the tubing picture until 1022, when 17S alloy tubing was introduced for aircraft construction.

Jan 1, 1951

By James H. Courtright, Kenyon Richard

TOQUEPALA is a porphyry copper deposit in which mineralization is localized by a large breccia pipe formed in close genetic relation to intrusive rocks. The deposit is in southern Peru, 55 airline miles north of the small city of Tacna and the same distance inland from the port of 110. Quellaveco and Cuajone, geologically similar deposits, lie 12 and 19 miles north of Toquepala. Chuquicamata is 400 miles to the south. The deposit is high on the southwestern slope about 20 miles from the crest of the Cordillera Occidental of the Andes Chain. It lies in a mountainous desert where the steep southwesterly slope of the Andes is dissected by a succession of rapidly downcutting, deep canyons. Local topography is moderately rugged with a dendritic drainage pattern and an elevation of 8000 to 14,000 ft. Volcanic peaks along the crest of the Cordillera rise over 19,000 ft. Local precipitation, including a little snow, amounts to about 10 in. during January and February, but general runoff in the region is slight. Throughout southern Peru the springs and streams are widely separated. Crude canals irrigate small farms on terraced slopes along the streams and provide sparse subsistence to the semi-nomadic inhabitants. During the past decade, engineering and geological explorations of the region, as well as the mineral deposits themselves, have required construction of a network of several hundred miles of roads. Before this, roads extended only a few miles inland. Many areas still can be reached only by trail. Toquepala was briefly described in 19th century geographical literature as a copper deposit, and it received desultory attention from Chilean prospectors early in the present century. It was first recognized as a mineralized zone of possible real importance by geologist O.C. Schmedeman during an exploration trip for Cerro de Paso Copper Corp. in 1937. The discovery was late as compared to earlier recognition of Chuquicamata, Potrerillos, and Braden of Chile and Cerro Verde of southern Peru. This was due partly to the region's difficult accessibility but principally to the obscure character of the outcrop evidence of copper. From 1938 until 1942 Cerro de Pasco Copper Corp. partially explored the deposit by adits and diamond drillholes. This campaign was supplied by a 60-mule pack train continuously shuttling over a 30-mile trail. Northern Peru Mining & Smelting Co., a wholly owned subsidiary of American Smelting & Refining Co., undertook regional engineering stud- ies in 1945 and drill exploration in 1949. According to published data1 the deposit contains 400 million tons of open pit ore averaging a little over 1 pct Cu. It is currently undergoing large-scale development by Southern Peru Copper Corp., which is owned by American Smelting & Refining, Phelps Dodge, Cerro de Pasco, and Newmont Mining. Summary of Geology: The deposit is situated in a terrane composed of Mesozoic(?) and Tertiary volcanic rocks intruded by dioritic apophyses of the Andean Batholith. These formations are exposed in a northwesterly trending belt about 15 miles wide. Along the northeast they are unconformably overlain by Plio-Pleistocene pyroclastic rocks, which occupy much of the crest of the Andes, and along the southwest they are covered by the Moquegua formation of Pliocene(?) age. The mineralized area, oblong in shape and about 2 miles long, has been a locus of intense igneous activity. Several small intrusive bodies having irregular forms occur within and adjacent to a centrally located, large breccia pipe. The mushroom-shaped orebody consists of a flat-lying enriched zone of predominant chalcocite with a stem-like extension of hypogene chalcopyrite ore in depth within and around the pipe. This breccia pipe is relatively large and has been formed by repeated episodes of brecciation. Small satellitic pipes occur at random within a 2-mile radius of this central pipe. These too were individual sourceways of mineralization, although not always of ore grade. Within and around the zone of breccia pipes and mineralization there are a few faults and veins, but these are discontinuous random structures of minor significance. There are no regional or local systems of faults or other planar structures recognized which could account either for the mechanical development of the breccia pipes or for their localization as a group or as individuals. Hydrothermal alteration is pervasive in the zone of mineralization. Clay minerals appear to be abundant in places, but their percentages are undetermined. Quartz and sericite are the principal alteration products, and in many instances original rock textures are obliterated. The principal sulfides, hypogene pyrite and chalcopyrite and supergene chalcocite, occur mainly as vug fillings in the breccia and as small discrete grains scattered through all the altered rocks. Sulfide veinlets are relatively scarce. Sulfides are more abundant and alteration is more intense in certain rock units, such as the diorite and most of the breccias. Although the Toquepala mineral deposit is similar in most respects to the porphyry copper deposits of southwestern U. S., it most closely resembles the Braden deposit of Chile, as described by Lindgren

Jan 1, 1959

By C. R. Sandberg, L. S. Gournay, R. F. Sippel

The effect of fluid-flow rate and fluid viscosity on oil-water relative permeability determinations was studied using the "dynamic flow technique." In this work relative per-nleability curves were obtained for homogeneous small core .samples from several sandstorle outcrop form-utions. Radio-tracers were used for the determination of fluid saturation and for the detection of saturation gradients. Cobalt-60 in the form of cobaltous chloride was used as a water-phase tracer in some of the experiments. Iodine-131 in the form of iodobenzene and Mercury-20-3 in the form of mercury diphenyl were used as oil-phase tracers in other experiments. Flow rates for each phase were varied within a range of 2.5 to 140.6 ml/hr. Oil-phase vis-cosities under flowing condition,> were varied from 0.398 to 1.683 cp. The relative permbilities ob-tained were found to he solely a function of saturation and independent of flow rare, provided there was no .Saturation gradient induced in the core sample by "boundary effect." Even though equilibrium with re-sped to flowing conditions was obtained at the lower flow rates, where a saturation gradient exists, this equilibrium is of a "contingent"-type rather than the "steady-state" equi-librium implicit in the relative per-meability concept. The only effect of increasing the oil or non-wetting phase viscosity was to decrease the flow rate required for the elimina-tion of the boundary effect. Fairly good agreement between experimentally determined and calculated values of the boundary effect was obtained when the non-wet-ring oil phase was the only Flowing phase. INTRODUCTION In the characterization of reservoir rock, as well as in the solution of reservoir production problems, it is most desirable to have reliablc rela-tive permeability measurements for the rock and fluids of interest. Many techniques have been developed for the laboratory determination of the relative permeability of both large and small core samples. In varying degree, difficulties attend the use of all of the methods. Each of the methods requires the metered flow of fluids of known viscosity through the core sample under conditions wherein the pressure drop in the individual flowing phases can be measured or closely approximated. Since the relative permeability is a function of the saturation and distribution of the flowing fluids, some means of obtaining such information is also required. The laboratory determination of the relative permeability of a sample should give the same relative permeability saturation relationship that would exist if the sample were in place in the oil reservoir. The attainment of this objective is complicated by the fact that the use of small core samples for laboratory measurements is usually necessary. As a result, errors in measuring the relative permeability arise from boundary effects at either the fluid input or output ends of the sample; no significant boundary effect is anticipated at the sides of the sample normal to direction of fluid flow. At the input end of the sample a boundary effect exists if the flow fluids are not com- mingled as they would be in the reservoir. At the output end of the sample a boundary effect exists as a result of discontinuity of the capillary properties of the system. Here the flowing fluids leave the small flow channels and enter a collecting system having much enlarged flow channels. Thus, there is a tendency for the wetting phase to be retained by the core sample because of the attraction of the core sample for the wetting fluid. No reference is made to these boundary effects in either Darcy's equation or in the relative permeability concept. As a consequence the saturation effect peculiar to the input end of the core sample may cause an error in the effective permeability measurement, since some portion of the core sample must be utilized for commingling of the flow fluids. At the output portion of the core sample a saturation gradient or a saturation change along the axis of flow results. Since relative permeability is a function of fluid saturation, this saturation gradient may cause a variable permeability measurement, especially since extent and character of the saturation gradient can vary with fluid-flow rate. The most convenient method of minimizing the boundary effect, especially at the output end of the sample, is to flow the fluids of interest through the core sample at such high rates that the capillary forces arc insignificant as compared to the viscous forces involved in the fluid flow. Since recent work of a preliminary nature has indicated that fluid dispersion in the porous medium increases with the flow rate, the high flow minimizes the boundary effect at the input end of the core sample by enhancing the mixing of the fluids.

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By V. B. Kurfman

Grain refinement of Mg-Al melts by carbonaceous additions has been attributed to nucleation by aluminum carbide. The effects of process and alloy variables are interpreted and predicted in terms of the dispersion and chemistry of this phase. The grain coarsening action of Be, Zr, Ti, R.E., chlorination, temperature extremes, and prolonged holding times is described. Measures necessary to insure an adequate dispersion of the catalyst are discussed. CARBON inoculation treatments have become fairly well known and used for grain refinement of magnesium alloys containing Al. Although there is general agreement that a nucleation process occurs, the process is not understood and the inoculants are used in a rather empirical fashion. The treatment is applied to the class of alloys containing 3 to 10 pct Al, i.e., AZ31A to AM100A. Typical methods involve melting, alloying, and adjusting the temperature to 1400° to 1450°F. Then 0.01 to 0.5 pct C as CaC2, C6C16, or lampblack is added by any convenient means, and the melt poured within 10 to 30 min. Investigators generally have been impressed by an assumed similarity of this refinement process to superheat grain refinement, which depends on heating approximately the same alloys to a temperature in the range of 1550" to 1650°F, then pouring promptly after the melt is cooled to the pouring temperature. Various predictions have been made that carbon refinement would replace superheating in commercial practice due to reduced process costs, but this replacement has not fully taken place because of production difficulties and conflicting observations. Davis, Eastwood, and DeHaven1 agree with Nelson2 and wood3 in suggesting that an excess of inoculant may be harmful. Wood however says that overtreat-ment is not a problem in production use of hexa-chlorobenzene inoculation, and Hultgren and Mitchell4 claim no evidence of harm from excess additions. Various grain coarsening reactions are known to occur, including the possibility of overtreatment mentioned above. Trace amounts of Be,2 Zr, and Ti may prevent refinement by either a carbon treatment or a superheat. Occasionally treatment with cl25 may cause coarsening, although the Battelle refinement process' uses a CC14-C12 blend. Grain coarsening also tends to occur on holding at temperatures below 1350°to 1400°F, especially after a superheat treatment, and for this reason Nelson2 stresses the desirability of a refinement method useful at lower temperatures for open pot melting practice. Since a carbon treatment can be made to work at temperatures below 1400°F, it seems desirable to investigate the mechanism of the refinement and the mechanisms of the coarsening reactions in order to establish control conditions for use in commercial production. The identity of the nucleating phase must first be established and then the factors affecting its chemistry and physical dispersion must be determined. THE IDENTITY OF THE NUCLEATING PHASE Davis, Eastwood, and DeHaven suggested that the nucleating phase in this system is Al4c3,1 but Mahoney, Tarr, and LeGrand8 disagree, largely because they found no evidence of the compound in alloys after carbon treatment and because there is no indication that aluminum carbide should be unstable over the temperature range used in the superheat treatment. This latter objection is based on the assumption that both the carbon treatment and the superheat treatment introduce the same nuclei. Electron diffraction studies have been made to identify the nucleating phase. Samples of grain refined A292 have been selectively etched SO that clean surfaces are obtained and so that secondary phases are in relief. Electron diffraction patterns from these surfaces have established that the carbon treatment of A292 introduces into the metal a large number of small, plate-like particles with a structure very similar to Al4C3. In most cases, the plate-like nature of the particles prevented positive identification but in the cases where the identification could be made the particles proved to be AIN A14C3. However, enough variation in lattice constants was observed so that all compositions from pure A14C3 to the 50:50 solid solution A1N.Al4C3 were probably present.14 In A14C3 and especially AlN.Al4C3 the A1 atoms occur in layers within which they have the same hexagonal symmetry and spacing as the Mg atoms in a single basal plane of a magnesium crystal. The solid solution spacing lies between the 3.16 of AIN and the 3.3? for Al4C3, in satisfactory agree-

Jan 1, 1962

By Paul Rhedey

Various commercial pelroleum cokes were heat-1,reated at temperatures between 500° and 1500°C, in a nitrogen atmosphere, in laboratovy induction furnaces. The rate of tenlperature rise was varied betzveen 10" and 300°C per min, or the green cokes were flash-calcined, orv a combination of heating rates was used. Changes in the rate of heating had only negligible effects on the degree of' calcination as characterized by mean crystallite thickness and the chemical properties of the calcined coke. The physical structure of the cake was however significantly affected when rate of heating during calcination exceeded 50°C per min over the temperature range of 600° to 900°C. Surface-accessible porosily increased with the .rate of temperature rise, and this was accompanied by a change in pore size distribution. Source and properties of the green coke also had an influence on the structure of the calcined coke. The evidence presented suggests a similar mechanism of porosity development in petroleuiiz coke during calcination in industvial equiplnenl, such as rotary kilns. An increase in surface accessible povosity incveased the pitch binder requirement when the coke was used as aggregate in Soderberg paste. A correlation was established between calcined coke porosity and paste binder requiremenl. ManY results have been published on the changes of properties of petroleum coke during calcination, such as chemical composition, real density, electrical resistivity, crystallite and pore structure. The correlation of these properties with temperature of calcination and time at maximum temperature has been rather well established in both laboratory and pilot plant experiments. Surprisingly little attention has been given however to the effect of calcination conditions, such as rate of temperature rise or furnace atmosphere, on the chemical and structural properties of the calcined coke. It has been observed that petroleum coke, when calcined in industrial equipment, acquires higher porosity and lower real density than those attainable in laboratory furnaces at apparently identical calcina- tion temperature and soaking time. This paper describes a study of the effect of rate of heating during calcination on calcined coke properties using green petroleum cokes of different volatile matter, hydrogen, and sulfur content. An attempt was made to correlate the changes in coke structure with the flowability of anode paste of the type normally used in aluminum reduction cells. EXPERIMENTAL Petroleum Cokes Used. In the study of release of volatile matter and sulfur during calcination and the effect of rate of heating on calcined coke properties two delayed cokes of different sulfur contents were used. The results of analysis of the green cokes are given in Table I. In the study of the effect of flash calcination thirty-six commercial petroleum cokes from twelve different refineries were used with a range of properties shown in Table 11. Calcination Conditions. Calcination experiments were carried out in a laboratory induction furnace. In each run a 200-g sample of dry green coke sized to 10 by 65 Tyler mesh was calcined in a graphite crucible. The crucible containing the sample was placed in the middle of a stack of eight others filled with metallurgical coke to reduce temperature gradients within the sample. Temperature was measured by two Pt, Pt-10 pct Rh thermocouples and controlled by a Celectray instrument. The two couples generally agreed within 5°C. In the study of volatile matter and sulfur release the samples were heated to temperatures in the range of 500" to 1500°C at a rate of 10°C per min in a nitrogen atmosphere and held at the final temperatures for 30 min. In the study of the effect of heating rate on calcined coke properties the desired rates between 10' and 300°C per min were obtained by manually adjusting the power input. Flash calcination was carried out by dropping 100 g of the green coke into the graphite dish preheated to the calcination temperature. Because of the small heat capacity of the furnace the coke was introduced in 20-g portions at a time. For this purpose a 2-in.-long nipple between two 1-in. gate valves installed on the top flange of the furnace served to provide a gas seal while feeding coke to the furnace. It was estimated that the temperature of the coke reached that of the furnace at a rate of approximately 1000°C per min. Holding time at final temperature was also 30 min. Calcined Coke Proper- Determined. Porosity was determined on 20 by 35 Tyler mesh samples using an Aminco-Winslow mercury pressure porosimeter with an operating range of 1.8 to 3000 psi absolute pressure (100 to 0.05 p pore diameter range).' Apparent density was obtained by the mercury poro-simeter. It represents a particle density of the 20 by

Jan 1, 1968

By Y Gu

The Mineral Liberation Analyser (MLA) employs the technologies of scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX). The use of backscattered electron images to define phase boundaries produces very high resolution image analysis and subsequently detailed and accurate particle images and data output. The mineralogy, elemental deportment, grain size, liberation characteristics and mineral associations of a large number of samples can be described. The MLA uses a comprehensive set of analysis methods to meet a wide range of applications. The data from ore characteristion projects completed during feasibility studies are important aids for effective plant design. The MLA can be used to establish variation in the mineralogy of an orebody, identify and quantify the deportment of deleterious elements, and provide valuable information to support comminution and flotation test work. In established plants the MLA data is an important component of plant survey work and monthly composite samples. Changes in feed characteristics and/or operating conditions can be monitored and solutions to any deterioration in recovery and grade performance found. The MLA has extensive applications in the minerals industry. Rare and precious metal samples can be accurately measured using high-resolution grey-scale images. Several new measurement techniques have been developed to perform rapid searches of a large number of samples to provide efficient and accurate analyses of fine-grain, low concentrate material. Quantifying the mineral variability in mineral sands operations is essential to maximising grades and recovery. The MLA produces particle-based data on density, mineralogy, size and shape and has developed measurement techniques to provide the elemental quantification required for the characterisation of these deposits. Nickel sulfide ores can be analysed to provide modal mineralogy, elemental deportment and liberation and locking data. The low-grade and variable nickel mineralogy of these deposits makes the use of quantitative mineralogy an essential component of maximising returns. Coarse particle measurements preserve the in situ textures of ores and support flotation and breakage test work for feasibility studies. The deportment of penalty and bonus elements can be quantified and the association and grain-size data can be used to identify potential separation issues.

Jan 1, 2006

By C. B. Manula, R. Venkataramani

Application of computers to present-day open-pit mining with bucket wheel excavators (BWE) is discussed. The development of the wheel excavators and their use in mining are discussed along with the necessity for building a computer model of the bucket wheel and the mathematical formulation of the problem. The simulation procedure, testing the model, and test results are summarized. Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the 20th century. Nearly 90% of all metals and mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management, and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mold of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. Constant efforts are needed to improve upon productivity if the ore is to be economically mined. The development of vast low-grade deposits and thick overburden deposits calls for better tools to handle the enormous amount of materials. A natural solution to this problem is the use of bucket wheel excavators (BWE), which employ a continuous cutting head to feed the materials handling system. High productivity, versatility, economy of operation, and adaptability to most types of haulage systems combine to make BWE's attractive for large earth-moving operations. "Operating costs are being pushed down by the impact of giant haulage units, by high-speed conveyors, and computerized railroads. Matching all these with the continuous output of BWEs, one can visualize increased production at much lower costs." Historical Background The wheel excavator, which was patented in Germany in 1913, made its first appearance in an open-pit lignite mine in 1920. From this early beginning, however, BWEs were slow coming into practice. Initial developments were dampened by many design problems. From 1936 onward, major developments in design improved the wheel's ability, capacity, and versatility. A literature survey shows that wheel excavators are being used in Australia, Zambia, South Africa, the Congo, India, Indonesia, Czechoslovakia, Russia, Great Britain, Guyana, Yugoslavia, Morocco, Germany, Canada, and the U.S. for mining and loading chalk, lignite, clay, sandstone, phosphate, broken ore of iron, coal, shale, loose and semi-loose rock overburden.' A recent LMG* BWE at work in a German lignite mine weighs 6790 tons with an hourly capacity of 11,000 cu m. Although the BWE has wide applicability, its application to new mining areas poses a problem. Because of the large capital investment involved in BWE application and the narrow profit margins in mining low-grade ores or coal at depth, little margin of error can be tolerated in the selection, design, and operation of these machines. The questions that need to be answered prior to installation of a BWE for a mineable deposit are: 1.) What are the anticipated BWE performance characteristics? 2) Which method of BWE operation is most efficient? Attempts to answer these questions require a thorough knowledge of the mining system and the BWE operation. One approach is the building of a computer-ori-ented simulation model to determine how information and policy create the character of the BWE system under consideration. BWE Operation Modern BWEs generally excavate in blocks. Fig. la shows a BWE working in an established cut. The wheel is positioned to travel on the pit floor in line with the top edge of the old highwall. As it advances, a new highwall is exposed in the direction of excavation. Digging is done by rotating the wheel, swinging it from side to side in long parallel arcs, and "crowding" into the bank, by advancing the entire machine, or by the travel of the digging boom if an automatic crowd is available (Fig. lb). A second way by which the wheel can be advanced into the bank is by the falling cut method. A brief description of each of these methods follows. Cut with a Crowding Machine: At the end of every swing, the digging boom can be extended by the thickness of cut desired and the boom swung back in the reverse direction. Obviously, the thickness of bank excavated does not vary with the boom position; therefore, the slewing motion of the boom is fairly constant for uniform output. The thickness through which the digging boom can be advanced into the bank is theoretically calculated from the formula'

Jan 1, 1971

ASHBEL WELCH, LAMBERTVILLE, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and, should not be overlooked,-the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destroyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. His doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de- * Metallurgical Review, vol. i, page 1. † The remarks as here given, as in the previous discussion on steel rails, have all been written out or revised by the participants in the discussion, and represent, therefore, their mature views. It has been thought that this plan, when it can be carried out without doing any of the speakers injustice in debate, is much to be preferred to a strictly verbatim report. The remarks of Mr. Chanute were sent to the secretary after the. meeting, and although they did not form a part of the actual discussion, there can be no doubt of the desirability of including them in this report. The papers under discussion were “Rail Specifications and Rail Inspection in Europe,” by C. P. Sandberg ; " The Wearing Capacity of Steel Rails in Relation to the Chemical Composition and Physical Properties," by C. B. Dudley, and a Rail Patterns," by A. L. Holley. T. M. D., Secretary.

Jan 1, 1881

By M. Baeyertr

Since 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallogmphy. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types. Radiography Radiography is the field in which the application of X-rays has had most general appeal among the industries which produce or use metals and alloys. Equipment permitting the examination of heavy sections of metals less permeable than aluminum or other light alloys requires apparatus capable of generating hard X-rays over a considerable period of time. The equipment used in the work presented in this paper is practically identical with that described by Fink and Archer in their paper on radiography in industry and is easily capable of penetrating 1/8 in. of lead. Radiography is used in two major groups of problems: (1) in the development of cquipment and tools and (2) in studies of materials. So far there has been no instance in which the use of radiography for routine inspection is justified. This is partly due to the fact that the manufacture of telephone apparatus involves the production of many identical parts by standardized procedures and equipment that has had development and trial before being put on a regular production basis. It is during this stage of development of equipment and tools that radiography has been used to particular advantage.

Jan 1, 1931

By C. D. Stahl, S. M. Farouq Ali

This investigation attempts to describe and simulate the alcohol displacement process by means of a cell model, as employed in chemical engineering practice. The proposed model is more simple than previously proposed models. and utilizes parameters chosen on a theoretical basis. The model successfully reproduced the formation of the stabilized bank and the breakthrough of alcohol, the latter depending on one of the model parameters, which may be correlated with the length of the porous medium. Moreover, the effects of the phase behavior of the liquid system involved, as observed in experimental studies, were reproduced. Several variations of the basic model were devised and tested on a digital computer. These included the cases in which: (1) the actual value of fractional flow was used in cell-to-cell computations; (2) the number of cells was varied within the same run; and (3) incomplete rather than complete phase equilibrium was assumed within each cell. The proposed cell model clarifies the basic mechanism of the process. Detailed concentration profiles obtained for each cell, for instance, showed the mechanism of bank formation in relation to the phase behavior characteristics. The results obtained indicated a varying degree of phase equilibrium concommitant with changes in the velocities of the phases in an actual alcohol displacement. This condition was approximated by changing the number of cells during the simulation. Interesting information was obtained on the influence of path length on the efficiency of alcohol displacement, which has been the subject of some controversy. Certain limitations preclude the use of the proposed model as a substitute for experimental studies. The results obtained were, nevertheless, of value in interpreting the experimental results. INTRODUCTION During recent years considerable effort has been directed toward an understanding of alcohol displacement, the process whereby oil and water are recovered from a porous medium by the continuous injection of a solvent. The complex nature of the physical process involved has so far defied a complete mathematical treatment. Other methods of approach, amounting to an overall material balance, have been proposed, yielding useful information on certain aspects of the process.1-3 Taber et al, in particular, defined the displacement mechanism in terms of the phase behavior of the alcohol-oil-brine system invoIved.2 Wachmann reported a mathematical treatment of alcohol displacement subject to certain simplifying assumptions? Donohue proposed the use of a "cell model" for simulating alcohol disPlacement.5 The nature of the assumptions involved limited the utility of the model. The present work attempts to examine the variables involved in the simulation of alcohol displacement and discusses several possible versions of the basic cell model. Under certain conditions the model results are similar to the experimental results. In particular, the spontaneous formation of of the stabilized bank and the effects of the system phase behavior were successfully reproduced. PREVIOUS WORK ON CELL MODELS Cell models and the theoretical plate concept are often used in solving chemical engineering problems in which an explicit mathematical solution may be difficult or impossible to obtain. Examples of such applications occur in distillation, gas-liquid chroma tography,6 reactor technology, absorption, etc. In petroleum engineering, such a model was used by Attra7 to describe non-equilibrium gas drive, and by Higgins and Leigh ton8 to calculate sweep efficiency in water flooding. Aris and Amundsen pointed out the equivalence between the diffusion model and perfectly mixed cells connected in series.9 Deans proposed a three-parameter cell model to simulate two-component

Jan 1, 1966

CHAIRMAN ALLEN: Gentlemen, I have been asked to call this meeting to order by Mr. Marchant, and am acting here temporarily in the absence of Mr. Nyman, who is unable to be with us. Mr. Nyman sends the following telegram: "Will not be able to be present at the Institute meeting. Serious illness of my father has made it necessary for me to remain in Salt Lake Please arrange substitute. Very sorry." In addition to having to pinch-hit for Mr. Marchant and President Nyman, I am here representing the Governor of the State of Colorado also who is unable to be here. The Governor of Colorado is a very busy man. His appointments are made months ahead. We only got word of the possibility of his addressing this meeting yesterday morning, and I went over to the Governor's office this morning to see if there was any possibility of getting him here, but he had been booked up for two months ahead of this time to appear at the convention of the Veterans of Foreign Wars in Trinidad, Colorado, where he is today, and which makes it impossible for him to attend this meeting. I know that he would have liked to have been here with you, as there is not any doubt but what the Governor of Colorado has the interests of the mining industry at heart. This was manifested last week when he called a meeting of representative men of the different lines of industry so that we could arrive at some results and some arrangements to see if it was possible to get at the bottom of the condition causing our bad times, and the appointment of commit- tee groups to find out what these problems were and to see if they could get any possible solution to them. The meeting was adjourned with the suggestion that those who were present would among themselves select such committees to investigate the conditions of the coal mining industry, and offer suggestions for betterment.

Jan 1, 1938

By Geoffrey Gilbert

A study of specimens shows that the key to both oxidation and enrichment at Duck-town is the behavior of pyrrhotite, which is in part dissolved and in part replaced by marcasite. Enrichment takes place chiefly at the expense of marcasite. THE material that forms the basis of this paper was collected in the spring of 1922, during a ten-day visit to Ducktown by the writer in the company of Prof. L. C. Graton. The time available for the work was far too short to allow anything like a thorough study of the deposits, and structural and stratigraphic questions, though they have an important bearing on the origin of the primary ores, were necessarily left untouched. Attention was focussed on the zone of oxidation and enrichment; and by devoting most of our time to the upper levels, open pits, and old workings, and examining the deeper levels only thoroughly enough to obtain a fair idea of the nature of the primary sulfide ore, we were able to make a reasonably complete survey of the various orebodies. With this field work for a background, the writer later made a study, in the Harvard laboratories, of the specimens obtained during the visit. As some of the facts brought to light by this study appear to be new, it seems worth while to set forth the outstanding features and a proposed explanation of them. Much of the Ducktown material that is obviously of greatest significance, as regards oxidation and enrichment, is soft and crumbly. Notwithstanding the desirability of gaining from such material all possible information as to its mineral composition and textural relationships, but little has heretofore been learned regarding it; but, by suitable preparation of this material in connection with the present study, it has been possible to examine it under the microscope without any disturbance of its texture and about as satisfactorily as if it were hard, fresh ore. The information thus gained has contributed measurably to the results set forth in this paper.

Jan 3, 1924

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By George S. Austin

Perlite is rhyolitic glass with 2 to 5 percent by weight (wt.%) bound water held within the silicic-glass structure. It is often distinguished by vitreous, pearly luster and concentric perlitic fractures ("onionskin"). Occurrences worldwide are associated with Tertiary to middle Quaternary volcanic rocks. Perlite is in silicic domes, plugs, laccoliths, flows, vitric tephra, chill margins of dikes and sills, and welded ash-flow tuffs. It is a hydrated volcanic glass formed through secondary alteration of obsidian by the incorporation of water into the glass/silica structure. Post-emplacement hydration (weathering) of cooled glasses by meteoric water is the principal alteration process, but some hydration by magmatic or meteoric water during or shortly after emplacement, or hydration by water exsolved during cooling may occur. Commercial "perlite" is any volcanic glass that expands or "pops" when heated quickly to plasticity while evolving steam and thus forming a lightweight, frothy material. The expansion temperature typically ranges from 1,100 to 1,500°F. An expanded volume increase of 10 to 40 times the original volume yields expanded densities of 1.5 to 11 pounds per cubic foot (lbs/ft3). Perlite is mined by eight companies at 10 operations in six western states. New Mexico accounts for more than 80% of the total tonnage mined. The rest comes from Arizona, California, Colorado, Idaho, and Nevada. In 1992, domestic production was 571,000 short tons (st), domestic apparent consumption was 591,000 st, and the value of crude perlite was $15.3 million. In 1991, with about the same production and price of crude perlite, the gross value for expanded perlite was $101.7 million. Perlite exports in 1992, primarily to Canada, are estimated an 30,000 st; and imports, from Greece, are an estimated 50,000 st. In 1992, 70 plants in 33 states expanded crude perlite. Construction uses of expanded perlite accounted for 66% of total domestic sales. Expanded perlite used as filter aid accounted for 15%. All other markets, including use as a filler and in agriculture, accounted for 19%. Leading states for expanding perlite, ranked by order of sales, were Mississippi, Pennsylvania, California, Illinois, and Georgia. Domestic perlite encounters transportation disadvantages in some areas of the eastern United States compared to perlite imported from Greece. However, western U.S. perlite exports to Canada offset this in large part, and net import reliance for perlite is about 3% of domestic consumption. Perlite grab samples were tested at the New Mexico Bureau of Mines and Minerals Resources (NMBMMR) for their basic suitability in horticulture, construction, filter aids, and fillers/extenders using Perlite Institute techniques modified by the NMBMMR. Most commercial perlite ranged from 2.5 to 3.0 wt.% bound water for all major types (classical, granular, and pumiceous). Expanded density varied widely, but the lowest density of 1.9 lbs/ft3 was for granular. Average brightness of expanded perlite was 47.6 to 69.3%. Nonexpansibles, commonly obsidian or "dead" perlite, ranged from 18 wt.% to less than 1 wt.%, with granular perlte generally the lowest. Compacted density was not related to either perlite type or nonexpansibles present. Sieve analyses of the -50+100 mesh product showed that, in general, pumiceous perlite produces more fines and classical and granular perlite average 60 to 80% -30+100 mesh after expansion. Samples were tested for crystalline silica that ranged from below the detection limit of 0.5 wt.% to nearly 0.2 wt.%, but most tested below 0.5 wt.%. Although quartz content can be lowered in the expanded product by the expansion process, producers can further lower crystalline silica in the product by mixing low-quartz crude with high-quartz perlite before expansion. Chemical analysis by x-ray fluorescence confirms the rhyolitic composition of perlite, but indicates that surface weathering may increase the concentration of some elements, such as potassium and calcium, by infilling cracks or fissures developed during or after perlite emplacement.

Jan 1, 1995

By Philip Bucky

THE general conception of a mine model is that of a three-dimensional object representing the mine workings, the orebody and the country rock of a particular property. Its chief uses have been to make it easier to understand the mine and to serve as a basis for the arguing of legal questions. Fayol endeavored to use mine models in a different way and to all students of subsidence "Fayol's dome theory" is of decided interest. We have more recently the suggestion of Young and Stoek of the University of Illinois, who1 suggest the use of models as a means of studying the problem. Prof. Henry Briggs, of the University of Edinburgh and Herriott Watt College, also makes use of models to determine the effects of bending at the edges of extensive workings.2 It is interesting to note that civil engineers are taking a decided interest in the application of models and the principles of dynamic similarity to the solution of their problems. The Proceedings of the American Society of Civil Engineers for 1930 contain an elaborate article by Benjamin F. Groat,3 who says, in his opening remarks: "Every engineer should know and understand that a model constructed in accordance with Newton's theory of similarity is not only the means for reproducing the complexities of flow, or other mechanical action, on a small scale, but that models may be made the best means of designing works of great magnitude. In the present state of knowledge, a properly constructed and properly tested model will answer the difficult questions of hydrodynamics much more quickly and accurately than the most profound mathematical analyses." A study of P. W. Bridgman's book on Dimensional Analyses leads one to arrive at the same conclusion.

Jan 1, 1931