Search Documents

By W. D. Sinclair, R. J. Cathro, E. M. Jensen

"The Cash is one of the largest porphyry copper-molybdenum Deposits found in Yukon to date. It is 80 km northwest of Carmacks, within the unglaciated portion of the Dawson Range, and is associated with the Big Creek fault, an important tectonic feature. Part of the mineralized zone is blanketed by up to 70 m of alluvial drift . The remainder is covered by a relatively thin residual soil layer. The mineralized zone, however, was not detected by conventional stream-sediment sampling because pathfinder elements, such as Cu and Mo, have not been geochemically dispersed into the main drainage system. The deposit was discovered by a combination of soil analysis and inspection of rock fragments from small pits.Twenty widely spaced, shallow drill holes have outlined an areaover 2700 m long and 550 to over 1000m wide that grades more than 0.1% copper equivalent (% CuE = % Cu + (5 x % MoS2)). Two smaller zones grading over 0.4% copper equivalent occur within the larger area. The limits of the widest end of the deposit have not been delineated.The Cash deposit is fairly typical of high-level, calc-alkaline porphyry copper-molydenum occurrrences in the Canadian Cordillera {cf, CIM Special Volume 15) and is representative of most prospects in the Dawson Range. It is associated genetically with a subvolcanic complex of small, irregular stocks and dykes of feldspar porphyry and related breccias of Late Cretaceous age. Copper and molybdenum sulphides occur along fractures, in quartz veinlets and disseminated in feldspar porphyry and in older metasedimentary and intrusive rocks. Higher-grade zones of copper and molybdenum have associated potassic alteration. Phyllic alteration is, in part, superimposed on potassic alteration. Argillic alteration occurs locally.This paper describes the history of the discovery and the geochemical and geophysical characteristics, together .with the regional geology, and the nature and distribution of the host rocks, hypogene mineralization and hydrothermal alteration."

Jan 1, 1981

By G. R. Heckman, H. J. Murphy, C. T. Sims

An incestigation has been made of the effects of heat treatment and alloy composition on the long-time stress-rupture properties and structural stability of the similar nickel-base alloys Udimet-500, Lrdimet-520, and Udimet-700. Rupture test data are presented at stresses ranging from 4 to 50 ksi at temperatures from 1450° to 1900°F for times up to 14,000 hr. Ductility response is emphasized. Optical and electron tnicroscopy were complemented by X-ray diffraction analyses of extracted phases to relate microstructural stability to the observed rupture properties. Particular attention is paid to Udimet-520 since structural characteristics of this alloy appear to vary somewhat from its sister alloys. Both cast and wrought performance of Lrdimet-500 are discussed. The computerized PHACOMP calculational technique, based on electron-vacuncy theory, is discussed and related to structural stability where appropriate. Electron microscopy and microprobe techniques were used to conduct evaluation of the oxidation characteristics of Udimet-500 exposed in air for 16,100 hr. The steady advance in strength and reliability of nickel-base superalloys continues to be one of the high points of modern metallurgy. The stress capability of these materials has increased steadily, allowing higher and higher operating temperatures in the highly sophisticated aircraft and industrial gas turbines now on the market. The attendant increase in efficiency, of course, means greatly improved power output. Gas turbines for industrial and marine use have long been designed with these objectives paramount the usual design requirements in terms of time of service being 100,000 hr. High-efficiency, long-life aircraft such as the supersonic transport require superalloy engine materials with high-strength and long-time structural stability. Thus, materials studied for and operating experience from industrial gas turbines provide a good reservoir from which technology of high value to the SST program can be drawn. This study is one such case. Three prominent nickel-base super alloys—Udimet 500, Udimet 520, and Udimet 700 were extensively evaluated for industrial gas turbine bucket use. Particular attention was directed toward structural stability as a requisite property. Within the present context, structural stability is defined as freedom from the propensity to form strength-robbing or embrittling phases such as u,p,x,or Laves, and the ability to maintain useful rupture strength and ductility throughout design life. MATERIALS The three alloys, cast Udimet 500 (U-500C), Udimet 520, and Udimet 700, were chosen for detailed evaluation based on preliminary studies which indicated that U-500C and U-520 possessed comparable rupture strength capabilities, and that U -700 had a greater strength capability but somewhat poorer ductility than wrought U-500. The nominal compositions of the three alloys, along with the compositions of the heats investigated, are presented in Table I. PROCEDURE Dimensionally rejected U-520 buckets from Special Metals Corp. heat 63370 were heat-treated using the four cycles delineated in Table 11. Cycle A was investigated to determine the effects of a shortened 1700°F primary age. Cycle B was considered a "standard" treatment. Cycle C investigated a higher solution temperature in combination with a shortened primary age, while cycle D assessed the effect of the higher solution temperature alone. These heat treatments were designed to produce optimum combinations of rupture strength and ductility through maximum y' development, the development of a y' grain boundary cushion, promotion of MC carbide degeneration reactions, and agglomeration of resultant M23CB. Since one of the premises of the evaluation of U-520 was that rupture strength would be equivalent to U-500, forged U-500 buckets from Special Metals Corp. heat 62916 were heat-treated with cycles A, B, and C to provide comparison. The heat-treated structures of U-520 and U-500 are illustrated in the 8700 times electron micrographs of Fig. l. The U-700 tested was all from 3-in.-diam hot-rolled and centerless-ground rod from Special Metals Corp. heat 2-1426. Two heat-treatment cycles were employed, E and F of Table 11. Cycle E is a standard four-step, triple-age treatment intended to provide an optimum match of strength and ductility through well-developed matrix and grain boundary y', as recommended by U-700 vendors. Treatment F is a shortened , single-age cycle which could provide a significant processing cost reduction should adequate strength and ductility be maintained. Following heat treatment, rupture specimens of U-500 and U-520 were machined from the buckets and tested. Standard rupture bars of U -700 were machined from the heat-treated rod and rupture-tested. Failed and withdrawn rupture bars were prepared and examined by optical and electron microscopy. Select specimens were electrolytically digested, and the residues analyzed for carbide and topologically close-packed phases using CrKa or CoKo radiation. Of the six different U-500C heats evaluated, five were cast by Misco Precision Casting Co. and one was cast by Haynes Stellite Co. Cast-to-size rupture bars

Jan 1, 1968

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By K. Y. Haramy

Deep coal mines with strong roof and floor strata frequently encounter face and rib bursts. The burst problem becomes more severe with increased depth. While the exact causes of bursts are often difficult to determine, localized high stress zones are common to their occurrence. This Bureau of Mines report describes a study at a mine using longwall systems that experienced both face and floor bursts. The study correlates shield loading, entry closure, and forward abutment pressure increases to observed burst occurrences. The results indicate that strong roof strata that overhang behind the longwall supports create additional abutment stress. When caving lags behind the face and the abutment zone does not advance ahead of the face during mining, stresses on the face may increase to a critical level, resulting in a burst. The critical level occurs when the stress in the abutment zone exceeds the ability of the coal and/or adjacent strata to store strain energy. Caving characteristics may be improved by inducing fractures in the roof or by providing sufficient support resistance to shear the roof. Data analysis of a major burst indicated a dramatic increase in floor heave, with a maximum occurring 80 to 100 ft inby the face, and a lag in the cave line behind the face supports. Analysis of the effects of caving characteristics and floor heave on burst occurrences is presented.

Jan 1, 1987

By Norwood B. Melcher

This report describes preliminary experiments by the Federal Bureau of Mines on the practicability of adding raw pellets of taconite concentrate to blast furnace feeds. The usual industrial practice is to harden the pellets by heating before they are charged to the furnace. The Bureau research demonstrated that raw pellets could be successfully smelted in an experimental furnace with no significant change in coke consumption and only a moderate increase in dust losses. The dust loss was 43 pounds per ton of metal for an all-pellet charge, compared with 7 pounds per ton for an all-sinter charge. Raw taconite pellets undergo only slight degradation during charging to the furnace if 1 percent bentonite is used as a binder. INTRODUCTION Fines and concentrates must be consolidated or agglomerated into larger masses before they can be smelted in a commercial blast furnace. Such agglomeration is usually done by sintering, pelletizing, nodulizing, or briquetting. Sintering has been the more common practice, but with the advent of taconite concentrates pelletizing is increasing in importance.

Jan 1, 1960

Abdul-Ahad. A., Student, Montana School of Mines, Residence Hall Butte, Mont. '39 Abramovits, Charles, Student, Case School of Applied Science Cleveland, Ohio. '37 Abreu, Ovidio M., Student, Univ. of Nevada Reno, Nev. '38 Acker, Voscoe, Student, Agricultural & Mech. College of Texas College Station, Tex. '39 Adams, Albert, Student, New Mexico School of Mines Socorro. N. M. '38 Adams, Charles W., Student, Michigan College of Min. & Tech Houghton, Mich. '39 Adams, Hugh T., Jr., Student, Univ, of Oklahoma Norman, Okla. '39 Adams, Jack L., Student, Univ. of Oklahoma Norman, Okla. '39 Adams, Jack M., Student, Univ of Alaska College, Alaska. '39 Adams, Lewis J., Student, Agricultural & Mech. College of Texas, Box 2514, College Station, Tex. '39 Adams, Robert E., Research Engr., Battelle Memorial Inst Columbus, Ohio. '38 Adamson, George M., Jr.. Student, Univ. of Utah Salt Lake City, Utah. '39 Adkisson, J. F., Jr., Student, Agricultural & Mech. College of Texas, Box 1003, College Station. Tex. '38

Jan 1, 1939

By Christopher Mark

The past decade has provided a wealth of practical experience with longwall pillar design. Design formulas developed specifically for longwalls have proven their value in numerous applications. Analytic methods, including numerical models, have a1 so made important contributions. These advances have been based on basic research into abutment loads, coal pillar mechanics, and the interaction between pillar performance and entry stability. The goal of this paper is to review the state of the art in longwall pillar design from the standpoint of the practitioner. Actual case histories are presented to illustrate the current capabilities and limitations of pillar design methods. The paper also discusses the advances that can be expected in the future.

Jan 1, 1990

By P. Tsang

In order to deal with ground control problems such as roof falls, floor heaves and pillar failures in underground coal mines, a new pillar design method based on the "yield pillar" concept is proposed. Using the finite element model simulation, the functions and mechanisms of the "yield pillar" are studied. The important variables that affect the stability of longwall entry-pillar system are identified. To simplify the geological and mining conditions, a new pillar design method classifies the in-situ roof and floor conditions into four categories: 1) strong roof and strong floor, 2) strong roof and weak floor, 3) weak roof and strong floor, and 4) weak roof and weak floor conditions. The design formulae are derived based on the finite element model simulation, stability study and nonlinear regression analysis. The finite element models used consider the plastic failure properties and time-dependent behaviors of rock. To better organize the finite element model simulation, the orthogonal experiment design is used to arrange the finite element models and proved to be very effective. An application example is used to illustrate the basic design procedures involved in the new pillar design method.

Jan 1, 1993

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By E. T. Turkdogan, L. S. Darken

Calcium ferrite melts were equilibrated with sulfur and oxygen-bearing gases at temperatures within the range 1290°C to 1620°C. The results show that at oxygen partial pressures below 10-4 atm the sulfide-reaction occurs and at higher oxygen pressures the sulfur dissolves in the melt principally as sulfate ion. It is also observed that when the product increases, sulfate ions are converted to pyrosulfate ions and the results permit the evaluation of the pyrosulfate/sulfate ratio. It is shown that the ratio y CaSO,/rCaO increases with decreasing concentration of calcium oxide in calcium ferrite, silicate and aluminate melts. Indications are that oxy-acids, e.g. silica, alumina and ferric oxide, increase yCaS0,. A few experiments were carried out within the sul-tide range and the results are in accord with those obtained by other investigators on aluminate and silicate melts. BECAUSE of the industrial importance and theoretical interest, many investigators have studied the reactions between molten oxides, silicates or alumi-nates, and gases containing oxygen and sulfur. The early work reviewed by Schenckl and studies made by Bardenheuer and Geller2 indicates that solution of gaseous sulfur in an oxide melt resulted in the replacement of the oxide ions by the sulfide ions. Measurements made by Grant and Chipman3 on the equilibrium partition of sulfur between molten iron and complex silicate melts also demonstrated that, for a given temperature and silicate composition, the distribution of sulfur between slag and metal increased with decreasing oxygen content of the metal. Fincham and Richardson4 studied the effects of temperature and partial pressures of sulfur and oxygen on the solubility of sulfur in simple silicate and alumino-silicate melts. They observed that at oxygen partial pressures below about 10-5 atm sulfur in the gas dissolved in the melt as sulfide ions, replacing an equal number of oxide ions of the melt. At oxygen partial pressures higher than 10-3 atm, sulfur entered the melt as sulfate ions. Similar studies were made by St. Pierre and Chipman5 using calcium ferrite and calcium silico-ferrite melts. The experimental data presented in this paper were obtained in this Laboratory about 10 years ago; this is the first formal presentation although a preliminary report was given previously.6 In each of these experiments, a pure synthetic CaO-Fe2O3 melt in a platinum crucible was equilibrated with a gas mixture (SO2-O2, SO,-air, SO2-CO, or SO2-CO2-CO) at a temperature ranging from 1296°to 1620°C. The experimental technique was essentially the same as that reported by Darken and Gurry,7 the main difference being that the atmosphere in the reaction chamber contained sulfur dioxide together with oxygen, or carbon dioxide-carbon monoxide

Jan 1, 1962

By Kung-Lee Wang

FOLLOWING the rapid recovery of previous years, the U.S. economy continued the upward trend and moved forward moderately and sporadically during the first half of 1962. There was a slow-down in the recovery rate, which was especially notable in the third quarter. The economy recovered in the fourth quarter, and by the end of 1962 the gross national product amounted to $555 billion, a new high, 7 percent above that of 1961. Production, employment, personal income, and corporate profits all achieved new peaks, but unemployment continued high and the prospects for improvement remained poor. The economy again failed to us~ its full potential; 1962 was a good year, but not good enough. During 1962, all industrial production climbed from the low in January to a high in late summer which lasted through the fall, and declined slightly at yearend. Mining production followed this pattern closely and most sectors were approaching record highs. Most minerals gained in value and volume of production. The steel-associated minerals group was the only exception, and it sustained a small net loss. The nonfuel minerals industry opened the year at a high level, maintained this high level until late summer, with the peak in May, and drifted downward toward the end of the year. The gains recorded by nonferrous metal mining partly offset the loss of ferrous metal mining, resulting in a small gain for metal mining as a whole. The upsurge of construction material minerals output was primarily responsible for the substantial increase in production of nonmetals other

Jan 1, 1963

By W. H. Hodgson, A. R. Preston

"Improved rail production techniques provide new options for the rail user. Steelmaking improvements offer tighter composition control, lower oxide and sulphide counts, greater control of segregates and freedom from hydrogen problem s. New ultrasonic, laser and eddy current equipment gives printout information on surf ace flatness, straightness and internal condition. These have come along at a time when dramatic changes have occurred on the rail heat treatment scene. Rails can now be deep hardened on or offline in ways which should eventually result in a complete rewrite of the world's specifications. Rails of simple composition can be produced in the hardness range 2801400 BHN as required. The rail user can choose the hardness within this range according to requirement without the necessity for any step changes in the process routes.It is suggested that this is the pattern f or the next decade.IntroductionRails have been the subject of very slow improvement over many years but developments gathered momentum in the early seventies. Recent improvements in quality and properties have provided dramatic increases in rail life under the more severe service situations. Rail profile grinding, lubrication and other track improvements have greatly added to expectations of even longer life. All of this, coupled to even newer mill heat treatment developments, tilt both technical and economic advantages away from tradition to the point where specifications will need to be rewritten so that railroads can take full advantage of these new products."

Jan 1, 1988

By J. E. Lamar, J. S. Machin

INSULATING materials include a wide variety of nonmetallic mineral products such as exfoliated vermiculite, expanded gypsum, 85 pct magnesia, diatomite, asbestos, perlite, cellular glass, pumice, silica aerogel, expanded aggregates and mineral wool. Except mineral wool, most of these products, or the materials from which they are manufactured, are described in other chapters of this book. PROPERTIES OF INSULATING MATERIALS The insulating properties of the materials considered in this chapter result in general from entrapping extremely small pockets of air in such a manner that heat is not transferred by convection. The minimum heat conductivities of such insulating materials are slightly greater therefore than the conductivity of still air. In addition, conductivity varies with the overall density of the material, the temperature range in which the measurements are made, and the form into which the material is fabricated. However, the numerical value of heat conductivity should not be the sole criterion of an insulating material; for a particular application it may be advantageous to use a material of somewhat higher conductivity in order to secure other desirable engineering properties. This is especially true with certain materials that are used because of their refractoriness. Comparative insulating values of some commonly used insulating materials are shown in Table 1. In comparing the values presented in this table it should be borne in mind that heat conductivity varies with the mean temperature, with the overall density, and with the amount of moisture present. With fibrous or granular materials it varies with fiber or grain size and with the amount and kind of binder, if any is used. Under some circumstances it may vary with the arrangement of

Jan 1, 1949

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981

By J. J. Botha

As a Demand Side Management (DSM) Project, money was granted for the procurement and installation of a 3-Chamber Pipe Feeder System (3-CPFS) at AngloGold Ashanti?s Moab Khotsong Mine in the Vaal River Area, Orkney. The first submission was done to ESKOM in December 2002 and the contract was signed in September 2006 at a cost of R 57-million with an envisaged reduction in power of 7 Megawatt per month based on a 90% utilization factor. The project was finally commissioned in December 2008. The technology is not new, but the intent of the paper is to share with others the experience gained by using the technology in a deep-level mine in order to reduce overall power consumption.

Jan 1, 2009

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By R. E. Somers

1. INTRODUCTION 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant County. The group is made up of two distinct moun-tain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City-, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy down-pour of rain. . The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 5, 1915

By R. M. Giegerich

"This paper begins with a brief history of Madawaska Mines, a brief description of the geology, mining methods and equipment, and the historical development of 7/8-in. tapered drilling equipment. It then outlines the performance characteristics and inherent problems of the traditional 12-degree, tapered connection, blade-type insert bits. Service-free (Unipass) button-type insert bits are presented as a possible solution to these problems. The paper concludes with an analysis of button bit performance to date.Brief History of Madawaska MinesMadawaska Mines Limited, near Bancroft, Ontario, is in Faraday Township, Hastings County, approximately 100 miles northeast of Toronto and 100 miles west of Ottawa.The mine re-opened in 1976committed to 1,500 tons per day to provide approximately 600,000 pounds of yellowcake (U3O8) per year to A.G.I.P. (an Italian government agency) under the joint ownership of Federal Resources Corporation, Salt Lake City (51%), and Consolidated Canadian Faraday Limited (49%). At present, the mine is producing approximately 2 pounds per ton (.1% U3O8) at the rate of 60,000 pounds per month. The mine employs about 400 employees.Brief Description of Geology, Mining Methods and EquipmentGeologyThe Grenville metasediments of the mine area are chiefly paragneiss, amphobolite and some carbonate (marble) rocks, which were intruded by a basic rock, altered to a metagabbrometadiorite. These formations are generally concordant, striking east to northeast and dipping 45 to 60 degrees to the south. Locally, the metagabbro is often discordant. The above group of rocks (mixed hybrid gneisses) forms the hanging wall of the south-dipping Faraday granite sheet and was intruded by nepheline syenite, syenite and granite. The ore occurs in the granite-syenite-pegmatite dykes that are probably genetically related to the Faraday granite. The ore shoots are erratically distributed within the pegmatite bodies, mainly on the hanging or footwalls but also medially. Their size varies from 50 to 350 feet in length, 5 to 40 feet in width and 50 to 200 feet in height. The ore occurs most frequently in a medium-grained granite or syenite, well hematized with 10 to 30% mafic crystals of pyroxene, amphibole and/or relics of the host rock."

Jan 1, 1982