Search Documents

By Attilio Ligasacchi

The production of magnetite in copper smelting has been the subject of wide investigation in the past.1-9 It is accepted that most of the magnetite is produced in the converters and returned to the re-verberatory furnace with the converter slag. Part of this magnetite is circulated back to the converters in the matte. As a result, if proper fluxing practice is not followed, and temperatures in the converting process are not strictly controlled, an undesirable circulating load of magnetite may occur. This might ultimately lead to saturation in the reverberatory bath with consequent settling of the magnetite at the furnace bottom. This paper contains the cumulative results of a series of investigations on the formation and control of magnetite presently being conducted by the metallurgical department of the Chino Mines Division of Kennecott Copper Corp. THE METHOD USED FOR THE DETERMINATION OF MAGNETITE AND OTHER MAGNETIC MATERIALS Conventional wet chemical magnetite analyses are neither reproducible nor theoretically sound. These analyses are sensitive to time, temperature, and heating rate-all factors which tend to decrease their accuracy and reproducibility. To overcome the unreliability of the above method, H. W. Mossman1 developed an inductance bridge magnetite "meter" which completely replaces the wet chemical analysis with the advantage of quicker and reproducible results. Fig. 1 is a schematic diagram of the meter in use in the Chino metallurgical laboratory. When a pulverized specimen with magnetic properties is placed in coil A of the inductance bridge circuit, the permeability of the core is increased, causing a voltage drop across the coil. The unbalance is amplified to operate the balancing motor which adjusts the movable iron core in coils C and D to bring the bridge back to balance. An indicator arm connected to the movable iron core indicates directly the percent, or weight, of the magnetic material in the specimen. Coil B acts as a reference coil and a zero adjustment. The meter is standardized with a set of various amounts of -100 mesh pure magnetite crystals (99.8 pet Fe3O4) thoroughly mixed in a test tube with -100 mesh quartz sand. These mixtures are combined with inert transoptic powder and heated to 140° to 160°C (melting point of the powder) and subsequently cooled to room temperature, solidifying the whole mixture, in this manner eliminating any possible preferential orientation of the magnetite grains. In order to determine the effect of the particle size" of the magnetite and other magnetic materials on the meter determinations, five size fractions were obtained by wet screening of the 99.8 pet pure magnetite and several reverberatory matte and slag samples. The following size fractions were investigated: -80 + 100; -100 + 150; -150 + 180; -200 + 250; -250 + 300 and -100 mesh. The deviation of the meter readings for the various sizes of each sample never exceeded ±0.3 pet. This deviation is considered well within the accuracy needed for common smelter operation procedures. Further investigation proved also that grinding slag and matte samples in our laboratory disc grinder normally produced a powder constituted of 95 pet -200 + 300 mesh. For practical purposes a - 100 mesh size was used as standard for our studies. It was also found that for rapid determinations tamping of the sample in the test tube was sufficient and gave comparable results with those samples solidified with transoptic powder. For the purpose of this study we define the magnetite content in copper smelter slags and matte as the equilibrium amount of crystalline Fe3O4 existent in the specimen at a given reference temperature, excluding any secondary magnetite precipitated in the specimen during nonequilibrium conditions. MAGNETITE DETERMINATION IN SLAGS Since it is impossible to ascertain the status of equilibrium of a conventional slag sample, due to

Jan 1, 1965

By C. C. Martin, M. C. Fuerstenau, R. B. Bhappu

Experiments revealed that quartz could not be floated in conductivity water at any pH with a long-chained sulfonate as collector. Various cations, Fe+++, Al+++, Pb++, Mn++, Mg++, Ca++, are shown to function as activators when the pH is such that the cation hydrolyzes. As the solubility product of the various cation-sulfonates was exceeded at the concentrations involved, precipitated cation-hydroxy-sulfonates, e.g. Fe (RSO3)2OH must be functioning as the collector in these systems. A number of interesting and important phenomena were revealed during a study of the response of beryl to sulfonate flotation.' Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH 3.0, about three ppm Fe+++ increased recovery of leached beryl from about 60 pct to 100 pct, whereas about four ppm Ca+ + reduced the recovery from 60 pct to 2 pct. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper Sulfonate Flotation of Beryl,' even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation-sulfonates are precipitated immediately in solution. That is, blueish-white clouds were noted to form after given additions of salts to known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe(RCO3)2OH and that bonding to the surface occurs through the hydrogen of the hy-droxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems in the presence of various cations at various values of pH. EXPERIMENTAL MATERIALS AND METHOD Sodium alkyl aryl sulfonate was chosen as the collector for the experimental work. The reagent, sup plied as a courtesy sample by the Shell Chemical Co., has the following physical properties: Physical form Solid — Finely ground Sulfonate content, pct wt 95 to 97 Molecular Weight 450 to 470 Number of carbon atoms in hydrocarbon chain 25 to 30 Melting Point, OF 250 to 260 Solubility Soluble in water with gel formation at concentrations higher than 25 pct by weight sulfonate This particular reagent was chosen because of its high active sulfonate content, long-chain length, and solid form. With the exception of the frother and sulfonate, all other chemicals were of reagent grade quality. Conductivity water was used in the experimental work. This water, made by passing distilled water through an ion exchange column, had an average measured conductivity of one micromho. Experiments were conducted at room temperature in a small glass flotation cell with the following procedure: 1) A redetermined amount of water and salt solution (e.g. CaC12 . 2H2O) were combined and the pH adjusted to a given value. 2) A given amount of sulfonate was added so that final solution volume was 130 cc. 3) One drop of Dow 250 frother was added. 4) Five g of quartz were added and the system conditioned for five minutes. 5) The pH of the system was measured (termed flotation pH).

Jan 1, 1963

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.' The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,' Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,' substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.' One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By Richard L. Breithaupt

INTRODUCTION A shuttle car is a self-propelled rubber-tired haul¬age vehicle designed specifically for underground min¬ing, primarily in coal mines (see Figs. 1 and 2). The drive mechanism is located on the sides of the vehicle, and the load is carried in the center. A chain-and-flight conveyor distributes the load when the car is being loaded by a loading machine or continuous miner and also discharges the load onto a conveyor belt or into a mine car. As the name implies, the shuttle car shuttles back and forth between the working face and the un¬loading point and is not required to turn around. Shuttle cars have served as primary haulage in this country since 1940 and still perform this function in most coal mines today. TYPES OF SHUTTLE CARS Shuttle cars may be battery-powered, diesel-powered, or cable-reel electric powered. Battery-powered cars were used between 1940 and 1950, but are almost out of existence today because of their limited power. Diesel cars have been used in coal mines, but are used mostly in noncoal mines where rules and regulations are not as stringent. Also, objections by organized labor have limited the use of diesel-powered shuttle cars in coal mines. Today, the largest number of shuttle cars are cable-reel cars. Electric power is fed through a cable stored on a cable reel that may have a capacity from 152 to 244 m (500 to 800 ft), depending upon the size of the cable and the cable reel (see Table 1). This, of course, limits the travel of a shuttle car. However, time studies have shown that for the most efficient haulage cycle, the length of haulage should not exceed 91 m (300 ft). As haulage distance increases, the waiting time for the loader or miner becomes longer, and haul¬age efficiency suffers. Cable-reel cars are manufactured in standard hand and opposite standard hand models. A standard car has the operator's control on the left front side and the opposite standard car has the opera¬tor's controls on the right front. Generally a loader or miner operates with two shuttle cars, one of each type. This allows the trailing cable to lie on either side of the entry and prevents the cables from fouling each other. Shuttle cars are designed to operate with either dc or ac power. Cars using dc power are designed for 250-v supply and ac cars are designed for either 440, 550, or 950 v, three-phase voltage. Most coal mines that are relatively level can use dc cars where dynamic brak¬ing is not required. For mines having steep grades (in excess of 15%) ac cars are used because ac traction motors have inherent dynamic braking and are safer when tramming downgrade. A recent innovation in shuttle car design in the last five years has been the introduction of an ac/dc car. This design utilizes ac input power through the cable, and the power is rectified on the car to 250-v do for traction motors. The pump motor and conveyor motor are powered by ac voltage. The main advantage of this design is efficiency-a much smaller cable may be used and the smooth operating characteristics of the dc traction motor is obtained. This prevents shock loading on the traction drive train, which is an undesirable feature of ac traction motors. SHUTTLE CAR FEATURES Elevating Discharge Today, all shuttle cars are equipped with an elevating front conveyor that allows the shuttle car to discharge into a mine car or belt feeder without the use of ramps. Hydraulic Power System Today, all shuttle cars are equipped with an hy¬draulic power system. An hydraulic pump is driven by an electric motor which provides hydraulic power for steering, elevating the front conveyor, and powering the

Jan 1, 1982

By W. C. Lilliendahl, G. Meister

Uranium metal with a purity of about 99.9 pct was produced on a large scale by fused salt electrolysis with a material efficiency of about 90 pct. The material efficiency depends mainly on bath composition, electrolysis temperature, electrode smothering, and elutriation during washing of the powder. RESEARCH and development work on fused salt electrolysis carried on by the Westinghouse Lamp Div. Bloomfield, N. J., was done under the Manhattan District Corps of Engineers and later under the Atomic Energy Commission for the commercialization of uranium production for the first atomic pile at the University of Chicago in 1942. From the conception of the atomic bomb project it was recognized that metals with impurity levels having little metallurgical significance would be required. Permissible impurity levels were based on neutron absorption. Of particular significance was boron, which could not be present in amounts exceeding 1 ppm. The electrolytic method as developed in 1930 by Driggs and Lilliendahl,1,2 and later improved, yielded uranium of very low boron and other deleterious impurity content. No other method was capable at that time of producing uranium metal of the required purity.' The low boron content of uranium produced by the electrolytic process resulted from the availability of the reactants which were low in boron content, and from the inherent elimination of boron in the fused salt bath. Since the heart of any electrolytic process is the electrolysis cell, this paper will deal with the development of the original bath composition for the efficient production of uranium from a batch process to one of continuous operation. Emphasis also will be placed on other factors which will affect the material efficiency of the process. With the laboratory cell the material efficiency of uranium powder recovery in the early electrolysis was relatively low, about 35 pct based on the ratio of uranium recovered to uranium added. This early process also had other defects. The electro- lytic bath could not be used continuously. After three runs from a freshly charged crucible, the deposit showed a tendency to slip off the electrode as it was raised from the bath. This condition necessitated pouring the charge every fourth run and preparing a new bath. It was assumed at that time that this condition was caused by the increasing fluoride concentration with each addition of uranium salt, which adected the mobility of the uranium ions. Experimental The electrolysis cells differed in size only. They were of the floating cathode type. The laboratory cells were 21/2 in. ID and 6 in. deep and operated at 30 amp and 5 volts. Production was about 150 g metal powder per 8 hr. The plant cells (5 units) were 9 in. ID x 21 in. deep and operated at 1800 amp at 12 volts. The total production unit was designed to produce 250 lb of uranium powder per 8 hr day. Because of the tendency of uranium fines toward spontaneous combustion, material efficiencies were based only on the recovery of useful coarser metal which could be safely handled. The reported efficiencies are of particular significance only as related to the same group of experimental procedures. At the start of the project no changes were contemplated until previous data could be definitely confirmed. Therefore, the first experiments were with the 50 pct CaCl2-50 pct NaCl mixture. The material efficiency of uranium deposition as a function of the number of electrolyses is shown in Table I. In Table I, the decrease in efficiency at 800°C with number of runs is apparent and confirmed the earlier data. Operating at 900°C enabled the number of runs to be doubled, but before pouring the charge the efficiency of recovery became poor. This test indicated that the improved efficiency might have been caused by an increase in the fluidity of the bath.

Jan 1, 1958

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By A. Haque

The shear behaviour of infilled joints produced from ordinary gypsum plaster (gyprock) and bentonite was investigated in the laboratory under Constant Normal Stiffness (CNS) conditions. Shear tests were performed on saw-tooth profiles having Joint Roughness Coefficients (JRC) of 4.75 and 9.25 under an initial normal stress (sno) of 0.30 to 1.10 MPa, and at a normal stiffness (kn) of 8.5 kN/mm. Test data under the same sno and infill thickness to asperity height ratio (t/a) were analysed for two different sets of JRC. The peak shear stress plotted against the t/a ratio under constant sno revealed an increase in peak shear stress with the increase in JRC, up to a t/a ratio of about unity. The effect of roughness on the peak shear stress was observed to be minimal when the t/a ratio exceeded 1.40. A mathematical model for the prediction of peak shear stress due to the increased infill thickness has been developed based on a hyperbolic stress-strain relationship and energy balance principles. The model predictions are in good agreement with the laboratory observations. Le comportement de cisaillement des joints remplis produits à partir de plâtre ordinaire et de bentonite a été étudié dans le laboratoire sous des conditions de rigidité normales constantes. Des essais de cisaillement ont été réalisés sur des profils en dents de scie ayant des coefficients de rugosité des joints (CRJ) variant de 4,75 à 9,25 sous un effort normal initial (sno) de 0,30 à 1,10 MPa, et une rigidité normale (kn) de 8,5 kN/mm. Le résultat des essais conduits sous la même contrainte et épaisseur de remplissage au rapport aspérité/hauteur (t/a) ont été analysés pour deux ensembles différents de CRJ. La variation de l'effort de cisaillement maximal contre le rapport t/a sous une contrainte normale constante a indiqué une augmentation de l'effort de cisaillement maximal avec l'augmentation du CRJ, jusqu'à un rapport de t/a proche de l'unité. L'effet de la rugosité sur l'effort de cisaillement maximal a été minimal quand le rapport t/a a excédé 1,40. Un modèle mathématique pour la prévision de l'effort de cisaillement maximal dû à l'épaisseur accrue du remplissage des joints a été développé sur la base de la variation entre contraintes hyperboliques et déformation et sur des principes de bilan énergétique. Les prévisions du modèle sont en bon accord avec les observations de laboratoire. Das Scherverhalten in mit gewöhnlichem Gips und Bentonit gefüllten Klüften wurde im Labor unter Bedingungen konstanter Normalsteifheit (CNS) untersucht. Scherversuche wurden durchgefürt für Sägezahnprofile mit Werten des Fugenrauhigkeitskoeffizienten (JRC) von 4.75 und 9.25 unter Normalspannungs-werten (sno) von 0.30 bis 1.10 MPa, und bei Normalsteifheit (kn) von 8.5 kN/mm. Testresultate für gleiche Werte von sno und Verhältnis Fülldicke zu Rauhigkeit (t/a) wurden untersucht für zwei verschiedene Werte von JRC. Die Beziehung zwischen maximaler Schubspannung und und t/a Verhältnis unter konstantem sno zeigte einen Anstieg der maximalen Schubspannung mit zunehmendem JRC, bis zu einem t/a Verhältnis von etwa 1.0. Der Einfluss der Rauhigkeit auf den Maximalwert der Schubspannung war minimal solange das t/a Verhältnis den Wert von 1.40 überstieg. Ein mathematisches Modell wurde entwickelt für die Vorhersage der Schubspannung die von zusätzlicher Fülldicke erwartet werden kann, ausgehend von einer hyperbolischen Spannungs-Dehnung Beziehung und dem Energiegleichgewichts-prinzip. Die Modellvorhersagen zeigten gute Uebereinstimmung mit den Laborbeobachtungen.

Jan 1, 2003

By M. A. Goudie

The deposits occur in a large salt basin of Middle Devonian age. The potash, the final deposit in the salt basin, results from several interrupted cycles of evaporation and dessication. The deposits are extensive, and, at first glance, relatively undisturbed. With more and more wells being drilled, it has now become evident that salt solution has played a large part in changing the original deposits, resulting in some cases in partial to complete removal of the potash and the underlying halite. The most dominant factor in the removal of salt by solution appears to have been tectonic movement and consequent faulting, probably of relatively minor dimensions but of major importance. Evidence which indicates the tilting of the evaporite basin to the north and northwest is shown by the changing pattern of the basin during succeeding eras of potash deposition. The potash minerals of most importance economically are sylvite and carnallite. Reserve calculations indicate that 6.4 billion tons of recoverable high grade potash in K2O equivalent exist in the basin. The Devonian salt basin, which contains the Saskatchewan potash deposits, extends from just east of the foothills in Alberta, north as far as the Peace River area, across Saskatchewan and into Manitoba as far east as Range 10 west of the First Meridian and south into Montana and North Dakota (Fig. 1). The basin is closed everywhere except to the northwest. The known potash deposits are confined almost entirely to the Province of Saskatchewan, with the exception of a small area in western Manitoba bordering the Saskatchewan boundary. The following discussion will concern only the Saskatchewan part of the basin. The evaporite series in the basin is defined as the Prairie Evaporite Formation of the Elk Point Group, of Middle Devonian age. Recent work done by potassium-argon dating methods has indicated an Upper Middle Devonian (Givetian) age of from 285 to 347 million years for the potash. The Elk Point Group consists in ascending order of the Ashern, Winnipegosis, and Prairie Evaporite Formations. The Ashern formation, with an average thickness of 30 ft, sometimes called the Third Red Bed, consists of dolomitic shales and shaly dolomites. The Winnipegosis, is a reef-type dolomite, usually with good porosity, and in many cases oil-staining, although to date no production has been obtained. The thickness varies from 50 to 250 ft. The Prairie Evaporite formation, varying from 0 to 600 ft in thickness, consists of halite with interbedded anhydrite and shale, with considerable amounts of potassium salts in the upper part of the formation. The potassium salts are chiefly chlorides, although very minor occurrences of sulfates have been re- ported. The anhydrite beds do not appear to be continuous, although generally one or two bands of anhydrite underlie the lowest potash zone and are used as marker horizons. The shale occurs as seams interbedded with the salts, as large irregular inclusions in the salts and as very fine particles in intimate mixture with the salts. The Prairie Evaporite Formation is overlain by the Second Red Bed member, the Dawson Bay Formation and the First Red Bed Member of the Manitoba Group, listed in ascending order. The Red Beds are shales which vary in color from red to green, maroon, grey, grey-black, and reddish purples. They serve as marker horizons for coring the potash. The Second Red Bed averages 14 ft in thickness, the First Red Bed 35 ft. The Dawson Bay Formation, which everywhere overlies the First Red Bed and the Prairie Evaporite Formation in the area under discussion, is a reef type of carbonate, in some places limestone, in others limestone and dolomite, with vugular to pinpoint porosity averaging 130 ft in thickness. In some parts of the area, it has a salt section near the top of the formation, usually with interbedded shales and limestones. In other parts of the area, it is waterbearing and the salt is absent. Detailed mapping has indicated that the areas in which the Dawson Bay is water-bearing are areas which have been disturbed by faulting. Where the Dawson Bay is salt-bearing, the porosity has been plugged by salt. The total thickness of the salt varies from between 600 to 700 ft in the center of the basin to zero at the northern edge of the basin (Fig. 2).* The salt-free area in the center of the Province is believed to have resulted from removal of salt by solution. Evidence from several wells suggests that salt removal has been a continuing process from the time of deposition to the present day. One well drilled between the Quill Lakes for potash information encountered

Jan 1, 1961

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke&apos;s Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty&apos;s work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke&apos;s Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By D. L. Kelley

High-viscosity water injection has been proposed for use in reservoirs containing high-viscosity crude oils. Previous publications have largely ignored the possible effects of the connate water on the proposed process. This paper describes experimental work which indicates that the connate water will be forced ahead of the injected water to form a bank of low-viscosity water. This decreases the oil recovery which would be expected if such a bank were not formed. These effects are shown for a range of fluid mobilities and connate-water saturations for a five-spot injection system. In general, oil recoveries using viscous water are significantly greater than for untreated water even though they are less than would be expected if no connate water bank were formed. INTRODUCTION The effect of mobility ratio on the oil recovery of wa-terfloods has been known for many years. Muskat first pointed out that the fluid mobilities (k/µ) in the oil and water regions would affect the performance of the water-flood, and he estimated the general effect of these variables.&apos; Since this early work, studies of the effect of mobility ratio on secondary recovery have been reported where mathematical,&apos; potentiometric3 and scaled flow models&apos; were used. These studies have shown that a reduction in the mobility ratio between the oil and the displacing fluid would cause additional oil recovery when water-flooding reservoirs containing viscous crude oils. Studies reported by Pye- nd Sandiford 8 have indicated that chemicals to increase injection water viscosity are now available and can be used to reduce the over-all mobility ratio of a waterflood. Where mobility ratios are controlled by the injection of viscous fluids, the connate water of the reservoir can play an important part in the displacement of the reservoir oil. The purpose of this study was to determine the effect of the connate-water saturation in waterfloods where viscous waters are used for injection. DISPLACEMENT OF THE CONNATE WATER Russell, Morgan and Muskat7 were the first to recognize the mobility of connate waters in waterflooding. They conducted waterfloods on oil-saturated cores containing 20 and 35 per cent irreducible water saturations, and found that from 80 to 90 per cent of the "irreducible" water was produced after only one pore volume of water was injected. However, their experiments were conducted at rates of flow significantly higher than those ordinarily occurring in waterfloods. Also, the cores were only from 4.0 to 8.5 cm long. Brown 4 studied a 100-cm linear sand pack which had been prepared to contain connate water and oil. He used 140- and 1.8-cp oils with injection water of essentially the same viscosity as the connate water. He found that all of the connate water was displaced by the injection water in both cases. However, the injection volumes required for complete displacement of the connate water were considerably higher in the case of the more viscous oil. To verify the results of the foregoing experiment, a 10-ft-long linear model was constructed by packing 250-300 mesh sand in a 1/2-in. diameter nylon tube. The model was evacuated, saturated with a brine of 1-cp viscosity, and flooded with a 41-cp mineral oil to the irreducible water saturation of 10.9 per cent. The model was then waterflooded by the injection of a water solution which had an apparent viscosity of 42.6 cp. The solution consisted of 0.5 per cent methylcellulose in distilled water. The viscosities of the oil and connate water were measured with an Ostwald viscosimeter. The viscosity of the polymer solution was calculated by Darcy&apos;s law using pressures measured during actual flow conditions. The ratio of the mobility in the oil region to the mobility in the inject ion-water region was approximately 0.32. The mobility ratio of the oil region to the connate-water bank was approximately 14. The mobility ratio between the connate-water bank and the injection water region was 0.024. Approximately 84.5 per cent of the recoverable oil was produced before water breakthrough. Immediately following breakthrough, oil and connate water were produced at an increasing water-oil ratio until the viscous injection water broke through. At viscous-water breakthrough, 96 per cent of the original connate water had been produced. After breakthrough of the viscous water, there was no additional production of connate water or oil. The near-

Jan 1, 1967

By A. Steiner, K. L. Komarek

Activities of aluminum in solid Ni-A1 alloys have been determined between 20 and 60 at. pet Al and 1200" and 1400°K by an isopiestic method in which nickel specimens, heated in a temperature gradient, are equilibrated with aluminum vabor in a closed all-alumina system. The activity of aluminum shows a strong negative deviation from Raoult&apos;s law at low concentrations but increases by three orders of magnitude within the ß(NiAl) phase. The partial molar enthalpy and entropy of mixing are negative. Using Wagner and Schottky&apos;s theory of ordered compounds, a degree of disorder of 4 x 10 -4 for NiAl and 1.25 X 10-2 for FeAl has been calculated THE Ni-A1 system has been studied by a great number of investigators, and the results, as far as the phase diagram is concerned, have been compiled by Hansen.1 The phase boundaries from 0 to 50 at. pet Ni are well-established. At higher nickel contents the boundaries are still in dispute and an additional phase, A12Ni3, has been reported.&apos; The phase diagram is dominated by a very stable high-melting compound, NiA1, with a relatively wide range of homogeneity. Heats of formation of solid alloys have been determined calorimetrically by Oelsen and Middel3 from 20 to 95 at. pet Ni and by Kubaschewski4 from 25 to 80 at. pet Ni. According to the most recent compilation5 no other thermodynamic investigations have been reported for the Ni-A1 system. Due to the corrosive nature and the low vapor pressure of aluminum, a method has been employed for determining activities of aluminum which was previously developed for the Fe-A1 system.= Nickel specimens, heated in a closed evacuated alumina system in a temperature gradient, were equilibrated with aluminum vapor from a source within the system kept at constant temperature. After complete equilibration the specimens were analyzed and activities calculated from the known vapor pressure of aluminum. APPARATUS AND EXPERIMENTAL PROCEDURE Materials. The nickel specimens were made from wafers of electrolytic nickel (International Nickel Corp.) of 99.99 pet purity which were rolled to a 0.001-in.-thick foil by Driver-Harris Co. and to a 0.005-in.-thick sheet in our laboratory. The aluminum (Aluminum Corp. of America) had a purity of 99.99+ pct. The alumina tubes and crucibles were made of impervious recrystallized alumina with an alumina content of 99.7 pet (Triangle RR, Mor-ganite Inc.). Experimental Procedure. Annular specimens were punched from the sheet, the punching burrs removed, and the specimens degreased in carbon tetrachloride and acetone and weighed on a micro-balance to within an accuracy of ±0.01 mg. The specimens were positioned with alumina spacers along an alumina tube, and the positions measured. Aluminum metal was machined into cylindrical shape, and placed into an alumina crucible. The tube with the specimens was then inserted into a hole drilled into the aluminum metal. An alumina tube with its closed end at the top was slipped over the specimens so that its lower end fitted snugly into the alumina crucible. The assembled reaction tube was inserted into a mullite tube with a water-cooled brass head which had an opening for a quartz thermocouple protection tube and a metal-to-glass connection to a conventional vacuum system. A Pt-Pt 10 pet Rh thermocouple could be raised and lowered in the quartz tube which was placed along the outside of the alumina reaction tube. The mullite tube was heated by two separately controlled resistance-tube furnaces so that in the experimental temperature range an over-all temperature gradient of approximately 150o to 250°C could be imposed on the reaction tube. The position of the mullite tube was adjusted so that the surface of the aluminum metal was always at the temperature minimum. The reaction tube was thoroughly evacuated before and during slowly heating the assembly up to the melting point of aluminum. A pressure of less than 2 µ (Hg) was maintained during an experiment. Once the aluminum had melted, it isolated the contents of the alumina tube from the surroundings. Several times during an experiment the temperature gradient was carefully measured. An experiment lasted from 3 to 6 weeks and it was terminated by air cooling the evacuated mullite tube. For further details of the experimental procedure the paper on the Fe-A1 system6 should be consulted.

Jan 1, 1964

By A. J. Heckler, J. A. Peterson

A capsule technique was successfully employed to investigate the effect of nickel on the activity of nitrogen in Fe-Ni-N austenite in the temperature range 600" to 1200°C. This technique consisted of equilibrating nitrogen among various Fe-Ni alloys within a sealed silica capsule. Nitrogen transfer among the specimens occurred by N, gas at 900°, lOOO? and 1200?C. Nitrogen gas pressures within the capsules were estimated to be as high as 22 atm. The activity coefficient of nitrogen, fN , in Fe-Ni-N austenite is adequately described by the linear interaction equation: log . wt pct Ni where the standard state is chosen such that fN = I as wt pct Napproaches zero in binary Fe-N. This relationship was determined over the temperature range 873" to 1473°K and for nickel contents of 0 to 35 wt pct. ALTHOUGH chemical thermodynamics of liquid iron alloys have been extensively studied, experimental data for the solid state are needed. These thermody-namic data will provide a basis for understanding phase transformations, precipitation reactions, metal-gas equilibria, and so forth. The interaction of sub-stitutional alloying elements with the interstitial elements is of particular interest. In this investigation the thermodynamic behavior of Fe-Ni-N austenite has been studied. The solubility of nitrogen gas in iron austenite is known to obey Sieverts&apos; law up to about 65 atm.1-6 In addition, the solubility of nitrogen in Fe-Ni austenite has been investigated5"8 using the classical method of equilibrating Fe-Ni alloys with nitrogen gas at 1 atm. A capsule technique similar to that used to study the activity of carbon in alloyed austeniteg&apos;&apos;&apos; was employed in the present work to determine the effect of nickel on the activity of nitrogen in Fe-Ni austenite over the temperature range 600" to 1200°C. EXPERIMENTAL PROCEDURE A series of Fe-Ni alloys up to 35 wt pct Ni was vacuum melted and cast into 1 by 3 by 6 in. ingots. Chemical analyses at the top and bottom of each ingot demonstrated that the ingots were homogeneous with respect to nickel content. The nickel contents are given in Table I. Additional chemical analyses showed that wt pct Si < 0.05, s < 0.01, C < 0.01, Al < 0.006, 0 < 0.004, Mn < 0.002, and P < 0.002. A 2 in. section of each ingot was cold rolled to 0.015 in. The material was then decarburized to a carbon content of less than 0.004 wt pct. A portion of the material of each nickel content was nitrided to various levels in a H2-NH3 gas atmosphere to provide a source of nitrogen during subsequent equilibration. The experimental technique consisted of equilibrating the series of Fe-Ni-N alloys in a partially evacuated sealed silica capsule at the temperature of interest. Both Vycor and quartz capsules were used. In general, the final equilibrium nitrogen content for each Fe-Ni alloy was approached from both higher and lower nitrogen levels. The criterion for establishing that equilibrium was attained was that the final nitrogen content for each Fe-Ni alloy was the same irrespective of the initial level. A schematic drawing of the sample configuration in a capsule is shown in Fig. 1. The samples were arranged so that there was a minimum of physical contact. The samples were also dusted with a fine, high purity alumina powder to help prevent sticking. Several different types of furnaces were used in this study. In each case, a thermocouple was placed immediately adjacent to the capsule during equilibration and the temperature was controlled to within *4?C of that reported. At each equilibration temperature, the following times were found to be more than sufficient to attain equilibrium: 600°C-250 hr, 900°C-150 hr, 1000°C-150 hr, and 1200°C-50 hr. After equilibration the capsules were quenched in water and the nitrogen contents of the specimens determined by a Strohlein analyzer. Analyses of samples after equilibration at 1000" and 1200°C showed no silicon pickup from the silica capsules. RESULTS AND DISCUSSION Transfer Mechanism. The mechanism by which nitrogen was transferred among specimens in an initially hydrogen flushed and partially evacuated capsule equilibrated at 1000°C was investigated. After equilibration the gas in the capsule was collected over water and an estimate of the pressure at temperature

Jan 1, 1970

By Dilip K. Das, Douglas T. Pitman

ONE of the major uses of barium in metallic form is as a getter material in vacuum tubes. Because of the high chemical reactivity of the metal, Ba-Al alloys are extensively used. Numerous methods for the preparation of Ba-Al alloys have been published, a few of which1-4 are cited here. Most of these methods were found to be quite elaborate, involving the reduction of BaO, and not too well adapted for the close control of the final composition of small amounts of alloys prepared for laboratory use. A simple laboratory method for the preparation of Ba-A1 alloys in small batches starting from pure metals was devised, so that it was possible to control the desired compositions to within 1 pct. The pertinent features of the alloy system Ba-Al5 are 1) an intermediate compound BaAl, with the melting point of 1050°C, and 2) a eutectic between aluminum and BaAl4 at 98 pct Al. The accompanying sketch shows the experimental arrangement for the preparation of the alloys. Weighed amounts of aluminum and barium were placed in an alumina and a stainless steel crucible, respectively. According to the supplier&apos;s specification, the purity of the metals used in the alloys is as follows: a) aluminum rods—99.9 pct Al, and b) barium rods—99.5 pct Ba. The stainless steel crucible, tapered at the bottom and having a 1/16 in. diam hole, rested on top of the alumina crucible. The assembly was placed inside a graphite sleeve which rested on a refractory platform. The platform moved the assembly up and down through the field of a radio frequency coil. A glass bell jar was placed between the crucible assembly and the radio frequency coil to maintain a steady flow of helium around the melt. A small window was cut out on the wall of the alumina crucible to observe the progress of the re- action and to record the temperature with an optical pyrometer. The platform was first raised high enough to move the barium out of the radio frequency coil field in order to allow only the aluminum to melt. The assembly was then lowered so that the barium began to melt and flow out through the small orifice into the molten aluminum. In order to keep the violence of the exothermic reaction under control, the rate of flow of barium was carefully regulated by raising or lowering the crucible assembly. All the samples prepared by this technique were examined by a Norelco X-ray diffractometer using CuKa radiation, The diffraction specimens were prepared by placing the finely powdered samples in flat specimen holders. The Ba-Al alloys prepared with a high barium content were found to consist mainly of BaAl4. The structure of BaAl4 has previously been reported by Alberti and Andress.8 They found that BaAl4 was body-centered-tetragonal with an a0 = b0 = 4.530Å and c0 = 11.14Å. An alloy whose composition was found by chemical analysis to be almost 100 pct BaA1, was used to determine the relative intensities. The d-spacings were obtained from the same alloy to which a small amount of tungsten had been added as a calibrating material. Accurate values for a, and c, were calculated according to the method proposed by Taylor and Floyd.&apos; The calculated values are: a, = b, = 4.566Å and c0 = 11.250Å. The measured d-values for BaAl4 are shown in Table I along with relative peak intensities above background and hkl indices. Acknowledgment The authors are grateful to L. J. Cronin, the head of the Techniques Dept., for suggesting the problem and for his constant interest. References 1Froges and Camargue: German Patent No. 809107, 1951. French Patent No. 935324, 1949. 2E. Bonnier: Annales de physique, 1953, vol. 8, pp. 259-312. 3M. Orman and E. Zemhela: Prac Institute of Metals; 1952, vol. 4, pp. 437-445. 4E. Fujita and H. Yokomizo: Reports Gov. Chemical Industrial Research Institute, Tokyo, 1952, vol. 47, pp. 291-297. 5E. Alberti: Ztsch. fur Metallkunde, 1934, vol. 26, p. 6. 6E Alberti and K. R. Andress: Ztsch. fur Metallkunde, 1935, vol. 27, p. 126. 7 A. Tnslor and R. W. Floyd: Acta Crystallographica, 1950, vol. 3, p. 285.

Jan 1, 1958

By D. Kunstelj, M. Stubicar, A. Tonejc, A. Bonefacic

A. Bonefafcic, D. Kunsfeli, M. Stubicar, and A. Tonejc The present communication is concerned with the variation of the texture in aluminum wires with die angle and temperature, at constant speed of extrusion. Experiments were carried out concurrently on refined samples, with a stated purity of 99.997 pct pure A1 and commercial samples of 99.5 pct Al. Ingots of refined aluminum samples were machined to 30-mm-diam by 150-mm-long billets. These billets were transformed to 5-mm-diam wires by drawing. The final form, suitable for examination, was obtained by extrusion through conical-face dies with a 1-mm hole diam and extrusion ratio 5:l in diam. The initial form of the commercial aluminum samples was drawn wire 5 mm in diam. These samples showed a poorly defined texture with (111) as a major and (001) as a minor component. A similar defined texture appeared in the refined aluminum samples after drawing to 5 mm diam. Conical-face dies with different angles (defined by the axis and the generating line of the cone) were used in our experiments. The values of the angles were 27, 35, 45, 57, 63, and 90 deg. The extrusion container was fitted with a heating element and controller permitting temperatures up to 600°C to be maintained within i5"C. Extrusion was performed at 250°, 300°, 350°, 400°, and 500°C at constant speed (approximately 1 mm per sec) and constant die reduction. The extrusion product was a wire 1 mm in diam and approximately 20 cm long. In order to remove the surface layer with the "conical" texture and to reduce the absorption by the X-ray examination of the samples, the extruded wire was etched to 0.22 mm in diam. Experiments were performed in the middle sections of the 20-cm-long wires. In addition to the die of l-mm hole diam, dies with a 1.5-, 0.7-, 0.6-, 0.5-, and 0.4-mm hole diam and 63-deg die angle were constructed. In our experiments we did not find in these ranges any important difference concerning the texture of the extruded wires and we continued our work solely on the 1.0-mm die. The diffracted X-rays (Cu K radiation) were recorded photographically. Diffracted intensities were measured on the (111) reflection with a microphotometer. The relative amounts of texture components were determined from the areas under the diffracted maxima. We found the texture of extruded aluminum wires to be strongly influenced not only by the temperature of extrusion and the purity of the sample but also by the form of the die. It is generally admitted that cold-drawn aluminum wires have mainly a (111) texture with a small amount of (001) component, Table I of Ref. 1. In our experiments with wires extruded in conditions represented by Fig. 1, in some cases a single (001) texture was obtained. If these wires were drawn repeatedly at room temperature, X-ray measurements revealed a duplex (001)-(111) fiber texture. Further drawings increased the (111) and decreased the (001) texture component. In Fig. 1 the percentage of material oriented with (001) parallel to the extrusion direction is represented as a function of the temperature and the die angle (a), for commercial and refined aluminum samples, respectively. From these diagrams we may draw the following conclusions. The slope of the die (a) influenced more strongly the texture at the lower rather than the higher temperatures. Again, a stronger influence was found in the case of the commercial in comparison with refined aluminum samples. In the case of the commercial aluminum samples the amount of material with (001) texture increases with increasing wire temperature in an approximately linear manner. This effect is less pronounced in the pure aluminum samples, with the exception of the die with a = 45 deg. In this case the (001) texture decreases with increasing temperature, as shown in Fig. 1. Component (001) is more pronounced in higher-purity aluminum samples. Our experiments led to the conclusion that both (001) and (111) components are essentially stable in extruded aluminum wires. As we obtained a single (001) texture starting with a sample of drawn wire in which the (001) component was very weak, our experiments revealed that the (001) component is not a remnant of the initial texture; this is in disagreement with the findings of Vandermeer and McHargue.1 We gratefully acknowledge discussions with Professor M. Paic. 1 R. A. Vandermeer and C. J. McHargue: Trans. 7MS-AME, 1964, vol. 230, p. 667.

Jan 1, 1969

By H. J. Hutson

BRS, Inc. has utilized Carlson&apos;s Natural RegradeTM software to design the reclamation and stabilization of abandoned open pit uranium mine spoils, AML Project 16N, located in the Gas Hills Uranium District in central Wyoming. This work was completed for the State of Wyoming&apos;s Abandoned Mine Land Program (AML) on preSMCRA (Surface Mining Reclamation and Control Act) sites for which no reclamation obligation existed. The project successfully stabilized an eroding spoil dump, enhanced the local view shed, created habitat diversity and provided a significant source of fill material for open pit highwall hazard mitigation efforts. Additionally, the project served to evaluate innovative reclamation design methods, engineering software and grade control technology. This project was nominated for a National Association of Abandoned Mine Land Programs award by the State of Wyoming. The results of this project will be presented as a case history of the Natural RegradeTM approach to surface mine reclamation. Based on the successful application of this new mine reclamation technology on the AML 16N Project, reclamation designs for spoils associated with planned underground uranium mine operations at the Velvet Mine in the Lisbon Valley Uranium District of Utah for Uranium One USA, Inc have been prepared and will be presented. Critical elements will be the encapsulation of unsuitable materials, long term hydrologic stability, and sequencing and staging of ore and mine waste for final reclamation surface construction. The goal of the Uranium One Velvet Project will be to apply best available technology to reclamation planning and fully integrate the reclamation design with the mine planning. Benefits of the approach should include improved public and regulatory perception of the project, facilitate mine permit approvals and the eventual timely release of reclamation bonds, as it is anticipated the stable landform created through this process will result in more rapid stabilization of the site to pre-mine geomorphic conditions. NATURAL REGRADETM CASE STUDY AML Project 16N, D-9 and K Pit Reclamation Project, is located in an intensely disturbed area of the West Gas Hills Uranium Mining District in Fremont County, Wyoming. The overall design calls for the placement of approximately 7 million cubic yards of backfill materials in the D9 and K Pits, imported from adjacent mine spoils including the Central Spoils, and from local highwall excavation. Figure 1 shows the location of the Central Spoils excavation area, as well as the D9 and K Pits fill area. The entire project is located on public lands administered by the Bureau of Land Management, Lander, Wyoming District Office. No access controls are in place at the abandoned mine sites. The public lands are administered under a multiple use land policy including grazing of range land, public recreation, active mining and exploration, and oil and gas. The project site is located along Fremont County Road No. 5, which is a moderately well traveled road. Reclamation of the numerous and large abandoned open pits in the Gas Hills Uranium District has reduced the risk of death or injury to the public. Site History and Background The Gas Hills Uranium District was mined by multiple companies during the period from 1955 to 1981. The uranium was hosted in the Wind River formation, a sequence of soft sedimentary layers of interbedded sandstone, clayey shales, and conglomerates. Uranium was precipitated out of ground water in classic roll front deposits, which are found from very near surface to depths greater than 400 feet. Prior to the enactment of the Surface Mining Control and Reclamation Act of 1977 (SMCRA), very little reclamation work was performed when mines were abandoned or closed. The State of Wyoming Abandoned Mine Lands Program has worked to mitigate hazards associated with large open pits, control migration of unsuitable materials and restore watershed functionality of lands in the district. Additional reclamation is being performed by mining companies on bonded lands. Figure 2, Gas Hills Uranium District aerial photograph, shows the extent of the mining disturbance in the district. [ ] Project Hazards and Concerns The purpose of AML Project 16N is to mitigate hazardous conditions and risk to the public associated with open pit highwalls and toxic, acid forming, and /or radioactive mine waste materials. The D9 and K Pits are contiguous open pits characterized by an 8,800 foot long hazardous highwall that averages over 200 feet tall. In addition to the physical hazard presented by the highwall, the project addresses

Jan 1, 2009

By N. J. Olson, G. W. Toop

A series of equations previously derived for calculating ternary thermodynamic properties using binary data has been applied to the problem of predicting ternary phase diagrams and quaternary excess free energy. The methods are considered to be rigorous for regular ternary and quaternary systerns and empirical for nonregular systems. The equations have been used to predict ternary phase boundaries in the Pb-Sn-Zn system at 926°K and the Ag-Pd-Cu system at 1000ºK. Calculated quaternary excess free-energy values are presented for the Pb-Sn-Cd-Bi system at 773°K. A method for predicting the location of ternary phase boundaries would be a useful supplement to experimental measurements in ternary systems. This has been recognized with the considerable work that has been done to find models to predict or extend thermodynamic properties and phase diagrams in binary and ternary systems1-18 for which direct experimental measurements are limited. With the access to highspeed digital computers and mechanical plotting devices, it is currently rather easy to compare mathematical models with experimental data. The regular-solution model is consistent with systems which exhibit negative heats of mixing, positive heats of mixing, and miscibility gaps, and therefore it is applicable to simple phase diagrams. The purpose of this paper is to illustrate the use of regular-solution equations to predict, empirically, phase equilibria in some types of nonregular ternary systems. Corresponding equations for regular quaternary systems are given and used to calculate empirical quaternary excess free-energy data. METHOD FOR PREDICTING THE LOCATION OF TERNARY PHASE BOUNDARIES USING BINARY DATA Meijerin1,6 has used the regular-solution model to calculate common tangent points to ternary free energy of mixing surfaces and hence to determine phase boundaries in ternary systems involving miscibility gaps. He used the following equation to calculate ternary excess free energy of mixing values: stants characteristic of the binary solutions, and Ni is the mole fraction of component i. An alternate expression which gives for regular solutions as a function of binary values of along composition paths with constant N1/N2, N2lN3, and N1/N3 may also be derived:15 ternary r xs 1 ?c-*n.Ti*.U*. This expression for is more useful for the empirical calculation of ternary excess free-energy values for nonregular systems because actual binary AFXS data may be used in the expression rather than attempting to find suitable constants for Eq. [I]. The results of this feature of Eq. [2] are illustrated in Table I where calculated excess free-energy values for the Ni-Mn-Fe system at 1232°K are compared with experimental data of Smith, Paxton, and McCabe.19 Although regular-solution equations have been shown to give calculated thermodynamic quantities which agree quite well with experiment for single-phase nonregular ternary systems,14,15 care should be exercised in the use of the equations to predict thermo-dynamic properties of multiphase ternary systems in which strong compound formation is suspected. This precaution is consistent with the simple regular-solution model which for negative values of ai_j will indicate a tendency toward compound formation but even for very large negative values of ai-jwill not give multiphase binary or ternary systems involving a distinct stable compound. Hence, calculated ternary free-energy data using Eq. [2] might be expected to vary between being rigorous and poor, in the following order, for ternary systems which are: a) regular solutions, b) nonregular single-phase liquids in which random mixing is nearly realized, c) nonregular single-phase solids, d) nonregular multiphase systems exhibiting miscibility gaps, e) nonregular multiphase systems with binary compounds but no ternary compounds, f) nonregular multiphase systems with highly stable binary and ternary compounds. The calculated data will be expected to be least accurate for the last two cases. The general method adopted in this paper involves two-dimensional plots of ternary activity curves. The principle used is that tie lines indicating two-phase equilibria join conjugate phases a and B for example, for which a1(a) = a1(B), a2(a) = a2(B), and a3(a) = a3(B). Tie lines may be determined by plotting the ternary activities of two components along an isoactivity line for the third component and the unique points where the above equalities hold may be found graphically.

Jan 1, 1970

By J. Chipman, M. N. Dastur

The importance of dissolved oxygen as a principal reagent in the refining of liquid steel and the necessity for its removal in the finishing of many grades have stimulated numerous studies of its chemical behavior in the steel bath. From the thermodynaniic viewpoint the essential data are those which determine the free energy of oxygen in solution as a function of temperature and composition of the molten metal. A number of experimental studies have been reported in recent years from which the free energy of oxygen in iron-oxygen melts can be obtained with a fair degree of accuracy for temperatures not too far from the melting point. Certain discrepancies remain, however, which imply considerable uncertainty at higher temperatures; also several sources of error were recognized in the earlier studies. It has been the object of the experimental work reported in this paper to reexamine these sources of uncertainty and to redetermine the equilibrium condition in the reaction of hydrogen with oxygen dissolved in liquid iron. The reaction and its equilibrium constant are: H2 (g) + Q = H2O (g); K1 _ PH2O / [1] Ph2 X % O Here the underlined symbol Q designates oxygen dissolved in liquid iron. The activity of this dissolved oxygen is known to be directly proportional to its concentrationl,2 and is taken as equal to its weight percent. The closely related reaction of dissolved oxygen with carbon monoxide has also been investigated:3,4,5 co (g) +O = CO?(g); K _ Pco2___ [2] K2= pco X % O [2] The two reactions are related through the wat,er-gas equilibriuni: H2 (g) + CO2 (g) = CO (g) + H2O (g); K2 = PCO X PH2O [3] PH2 X PCO2 and with the aid of the accurately known equilibrium constant of this reaction, it has been shown5 that the experimental data on reactions [1] and 121 are in fairly good, though not exact, agreement. Experimental Method Great care was taken to avoid the principal sources of error of previous studies, namely, gaseous thermal diffusion and temperature measurement. The apparatus was designed to provide controlled preheating of the inlet gases and to permit the addition of an inert gas (argon) in controlled amounts, two measures found to be essential for elimination of thermal diffusion. A known mixture of water vapor and hydrogen was obtained by saturating purified hydrogen with water vapor at controlled temperature. This mixture, with the addition of purified argon, was passed over the surface of a small melt (approximately 70 g) of electrolytic iron in a closed induction furnace. After sufficient time at constant temperature for attainment of equilibrium the melt was cooled and analyzed for oxygen. GAS SYSTEM A schematic diagram of the apparatus is shown in Fig 1. Commercial hydrogen is led through the safety trap T and the flowmeter F. The catalytic chamber C, held at 450°C, was used to convert any oxygen into water-vapor. A by-pass B with stopcocks was provided so that the hydrogen could be introduced directly from the tank to the furnace when desired. From the catalytic chamber the gas passed through a water bath W, kept at the desired temperature by an auxiliary heating unit, so that the gas was burdened with approximately the proper amount of water vapor before it was introdvced into the saturator S. All connections beyond the catalytic chamber were of all-glass construction. Those connections beyond the water bath were heated to above 80°C to prevent the condensation of water vapor. After the saturator, purified argon was led into the steam-hydrogen line at J, and finally the ternary mixture was introduced into the furnace. THE SATURATOR The saturator unit comprised three glass chambers, as shown in Fig 1, the first two chambers packed with glass beads and partially filed with water and the third empty. Each tower had a glass tube with a stopper attached for the purpose of adjusting the amount of water in it. The unit was immersed in a large oil bath, which was automatically controlled with the help of a thermostat relay to constant temperature, ± 0.05ºC, using thermometers which had been calibrated against a standard platinum resistance thermometer. The performance of the saturator over the range of experimental conditions was checked by weighing the water absorbed from a measured volume of hydrogen; the observed ratio was always within 0.5 pct of theoretical.

Jan 1, 1950

By Rex O. McLellan

The formation of a monovacancy in a metal is simulated in an elastic model by the displacement of the surface of a small spherical cavity in a large elastic continuum. The application of linear elasticity to this distortion results in a well- known formula for the energy and an expression for the concomitant entropy change due both to the shear strain in the continuum and also to the dilation of the solid resulting from the boundary conditions at the surface of the solid. Elastic data (the sliear modulus and its temperature coelficient) are used to calculate the entropy and energy of formation for many metals. Despite the simplicity of the assumptions involved, the agreement between the calculated entropies and energies and experimental values is remarkably good. In recent years there has been a large increase in measurements of the absolute concentration of mono-vacancies in metals as a function of temperature. Hence new data for both the energy and the noncon-figurational entropy of formation of monovacancies has become available. Recent measurements&apos; of the anomalous (non-Arrhenius) self-diffusion in many bcc metals has also focused interest on the prediction of the thermodynamic parameters of mono- and multi-vacancies in those metals for which no data are available. Damask and Dienes&apos; have discussed the various theoretical calculations of the energy of formation EL, of a monovacancy. These include simple models involving the breaking of atomic bonds on moving atoms from the interior of a crystal to the surface, models combining elastic calculations with surface-energy terms and detailed quantum mechanical calculations. The simler models give the correct order of magnitude of &, but tend to overestimate it by a factor of about two. The quantum mechanical calculations4"7 have been carried out for the noble and alkali metals with generally reasonably good agreement with the available Ef data. The calculation of entropy of formation Sfv14 lnvolves a fundamental calculation of the perturbation of the phonon spectrum caused by the creation of a vacancy. Huntington, Shirn. and wajda8 have given an approximate evaluation of sJV by considering an Einstein model for the localized vibrations in the immediate neighborhood of the defect and then using elastic theory to calculate the entropy associated with the shear stress field in the distorted crystal (as originally proposed by Zenerg). They also included a term due to the dilation of the crystal. They obtained a value of 1.47k for copper, in good agreement with the experimental value (1.50k). However, Nardelli and Tetta- manzi1° have recently shown that neglecting the coupling between atoms (Einstein Model) may lead to a serious error so the agreement may be somewhat fortuitous. In this work simple linear elastic theory is used to calculate the entropy and energy of formation of mono-vacancies. Despite the simplicity of some of the assumptions involved, the agreement with the available experimental data is remarkable. However. the reasonable degree of success in the application of linear elastic calculations to the excess entropy of a solute atom in a dilute solid solution1&apos; indicates that the application of elastic theory to vacancies. where the interaction of different atomic species is not involved, may not be inappropriate. THE ELASTIC MODEL The metal is assumed to be a spherical elastic continuum. A small spherical cavity of volume V = 4i;v:&apos;/3 is cut from the center. removed. and dissolved rever-sibly in the bulk of the material. TO a good approximation no net atomic bonds are broken and the material does not undergo a volume change although the externally measured volume of the body would increase by V. The radius of the sphere of metal is much larger than r Next a negative pressure is applied to the cavity causing its surface to be displaced inward by an amount simulating the relaxation of the lattice around a monovacancy. In this model the energy and entropy accompanying the distortion are taken as 4, and <. As a first approximation the equation of state for the solid is taken as: r = ro(i + *~D LiJ where K is the bulk modulus. P the hydrostatic pressure. Vo the volume of the material at 0°K and zero pressure. and d+/dT = 30. where 0 is the linear thermal expansion coefficient. The variation of entropy with hydrostatic pressure is given by the Maxwell equation: These equations give the entropy change resulting from increasing the hydrostatic pressure from 0 to P as: and since • we have: This is the entropy arising from the dilation resulting

Jan 1, 1970

By J. Chipman, G. G. Hatch

One of the important functions of the iron blast furnace is the desulphur-ization of pig iron before it enters the steelmaking furnaces. However, the increasing concentrations of sulphur in the metallurgical coke, source of approximately 90 pct of the sulphur present in the blast furnace charge, and demands for higher rates of production within recent years have increased the need for greater desulphurization within the iron blast furnace. Furnace operators are beginning to look for desulphurizing agents other than blast furnace slag to accomplish the desired degree of desulphurization. A considerable amount of work has been done on desulphurization outside the furnace with soda ash, calcium carbide and various synthetic slags. Whether the desulphurization of pig iron is accomplished wholly inside the furnace or partly inside and the remainder outside, will be determined by the economics involved. Regardless of which is the case, it is believed that it is necessary to have a better understanding of the physical chemistry of desulphurization by blast furnace slags. To this end, it is the object of the present investigation to attempt what is believed to be the first equilibrium study of the distribution of sulphur between liquid pig iron and a wide range of blast furnace slag compositions. Review of Literature There is a considerable amount of information in the literature concerning the desulphurizing power of iron blast furnace slags, the solubility of various sulphides in the slags, and the effect on desulphurization of temperature, of elements dissolved in the liquid iron, and of viscosity. However, there is nothing to indicate that the equilibrium distribution of sulphur between liquid iron saturated with carbon and iron blast furnace slags has been studied experimentally. Wentrupl has made probably the most detailed study of the desulphurization of pig iron to date. He considered that there are three distinct aspects involved, namely: 1. Desulphurization within the blast furnace (by lime and manganese). 2. Subsequent desulphurization by manganese. 3. The effect of subsidiary reactions on the desulphurization by manganese. The experimental work carried out by Wentrup was devoted mainly to obtaining a better understanding of how desulphurization by manganese was accomplished in the mixer and the ladle. Particular attention was given to the part played by carbon, silicon, and phosphorus associated with manganese in the iron, and the effect of temperature on desulphurization. The experimental results indicated that desulphurization by manganese is purely a process of crystallization of manganese sulphide. The addition of silicon to iron melts containing 3.5 pct carbon and less than 0.5 pct manganese had no noticeable effect on desulphurization, but with 1-2 pct manganese the silicon additions improved the desulphurization. Additions of phosphorus also resulted in improved desulphurizati011 by manganese, but the effect was not as marked as in the case of silicon. It was also found that desulphurization by manganese was further improved by lowering the temperature. In order to explain desulphurization inside the blast furnace, Wentrup considered the system iron, sulphur, calcium, oxygen, manganese. (silicon). The distribution of sulphur between the metal and slag was represented by the following equation: (SS) _ (S)Fe + (S)Ca + (S)Mn .... [S] = [s] [1] The parentheses and the brackets represent the equilibrium concentrations in weight per cent of the slag and metal constituents, respectively. Since FeS D (FeS) _ (FeS) (S)Fe LfeS - [FeS] [S] [2] (CaO) + S e (FeO) + (S)Ca _ (FeO)(S)Ca. (S)Ca _ (CaO) Kl = (CaO)[S] [S] ~K1(FeO) [3] Mn + S D (S)Mn (S)Mn (S)Mn K&apos; = [MnpT "1ST = *lIMnJ !4) Substitution of Eq 2, 3, and 4 into Eq 1 resulted in if = L- + *> (Sol + K^ (S) [51 Eq 5 was used to calcu1;lte -f^j and [S] at 1480°C for slags containing 30-50 pct lime, 0.1-2.5 pct iron oxide, 0-26 pct silica, 2 pct sulphur and iron analyzing 1.5 pct manganese. The value for LFaB at 1480°C was found to be equal to 4.5, based on the experimental work of Bardenheuer and Geller.2 The results of the calculations are shown in Table 1. Although the slags are hypothetical and do not represent the range of compositions found in ordinary blast furnace practice, the calculations indicate that lime is effective in controlling desulphurization only if the iron oxide and silica contents of the slag are kept low. Schenck3 did not claim K1 to be a true equilibrium constant, but an empirical value which varied with the silica content of the slag.

Jan 1, 1950