Search Documents

By N. C. Matheson

The West's Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989

By R. A. Sharma

Neodymium metal was successfully produced by the reduction of Nd203 with Na in the presence of CaC12-NaCl melts by the overall reduction reaction Nd203 + 3 CaC12 + 6 Na ? 2 Nd + 3 CaO + 6 NaCl at -750°C. The metal produced was extracted from the salt media by dissolving it in a Nd-Fe alloy pool. The yield (percentage of theoretical neodymium produced) was found to depend on the salt composition and the mass ratio of salt to neodymium in the reactor. A yield of 95% was obtained with salt ratios as low as 3.5. Further decrease in the salt ratio below 3.25 decreased the yield. Stirrer position had little effect on yield; while increasing the temperature and placing fins in the reactor increased the yield. The Nd-Fe alloy produced was of as good quality as that produced using Ca reductant, and was suitable for direct use in producing General Motors MAGNEQUENCH? alloy for permanent magnets.

Jan 1, 1989

By V. Castranova, K. VanDyke

"INTRODUCTION A soluble mediator has been described which is released from activated rabbit leukocytes and induces histamine secretion from rabbit platelets (Barbaro and Zvaifler, 1966; Siraganian and Osler, 1971). This factor has been isolated, characterized and named platelet activating factor, PAF (Bcnveniste et. al., 1972). PAF has since been chemically identified as l-0-alkyl-2-acetyl-sn-glyceryl-3-phosphocholine (Benveniste et. al., 1979; Demopoulous et. al., 1979).PAF is a lipid mediator of broad biological activity. It causes smooth muscle contraction, contraction of lung tissue and decreased FEV 1; while enhancing capillary permeability thus causing edema (Pinkard, 1983). In addition, PAF is a chemoattractant and can lead to inflammation.PAF has been reported to stimulate the release of lysosomal enzymes, leukotriene B,, and lipid metabolites from neutrophils (Smith et. al., 1983; Shaw et. al., 1981; Lin et. al., 1982; O'Flaherty et. al., 1984). The objective of the present investigation was to further characterize PAP-induced stimulation of granulocytes and to develop a bioassay, i.e. chemiluminescence, for screening PAF receptor antagonists and inhibitors of PAP-induced activation of granulocytes. The possible use of the chemiluminescence assay to monitor PAF synthesis by human granulocytes is also described.METHODSBlood was drawn from healthy volunteers into a blood storage bag containing CPD anticoagulant. Granulocytes were partially purified by dextran sedimentation and further purified by centrifugal elutriation as described previously (Jones et. al., 1980). Granulocytes obtained by this procedure were approximately 95 percent pure. The number of granulocytes in this preparation was determined using an electronic cell counter (Coulter Model Z1, Coulter Instrument Co., Hialeah, FL). Isolated granulocytes were used to monitor membrane potential, hydrogen peroxide and superoxide release, oxygen consumption, calcium uptake and, in some cases, chemiluminescence. Studies of PAF receptor antagonists were conducted using neutrophils isolated by density centrifugation. Briefly, blood was layered onto Mono-Poly-Resolving Medium (Flow Laboratories, McLean, VA) and centrifuged at 22 °C and 300 g for 30 min. Neutrophils collected from the second band of this gradient were at least 90 percent pure."

Jan 1, 1989

By Harrison R. Cooper

Composition data is needed as input for executing process control and management of particulate separation for flotation control. While requirements for composition data can be satisfied in many cases by manual sampling and analysis, automatic sampling and assay systems are now viewed as justified for all but the simplest or smallest processes. On-stream X-ray fluorescence analysis (XRFA) has satisfied requirements for the main portion of metalliferous sulfide ore flotation processes as XRFA technology evolved in reliability and sophistication from its beginnings in the late 1950's. In recent years, advanced on-stream analysis technologies have reached levels of development suitable for use in process control to increase efficiencies of important processes in mining and minerals industries such as coal fines flotation and industrial minerals beneficiation (particularly phosphate beneficiation) where XRFA methods have been inapplicable. Recent technical developments pertinent to use of advanced technologies as well as improvements to established on-stream composition analysis methods are discussed.

Jan 1, 1989

By Peters S. G, Beams S. D

CONCEPTS AND REGIONAL GEOLOGY The Charters Towers region holds many keys to the metallogeny associated with the complex geological development of eastern Australia during the Palaeozoic. Tectonic, magmatic and volcano-sedimentary depositional episodes can be identified and related to the chronological development of batholithic host rocks (Clarke & Paine, 1970; Henderson, 1986; Murray, 1986). Pre-batholithic basement rocks in the north (Charters Towers Metamorphics) consist of a package of amphibolite grade schists interlayered with and intruded by gabbros and diorites (Peters, 1987). To the south (Seventy Mile Range Group) greenschist facies Cambro-Ordovician rocks overly some of the basement. The lower age of this basement is not constrained, parts of it could be as old as Pre-Cambrian. Mid-Ordovician (approx. 470 my) to Lower Devonian (approx. 400 my) age I-Type granitoid plutons of the composite Ravenswood batholith intrude the pre-batholith basement and the Seventy Mile Range Group. Igneous activity was initiated again in the Carboniferous with the extrusion of rhyolitic lavas and pyroclastics associated with porphyry and high-level intrusive complexes (Wyatt et al., 1971). The Ravenswood block is bounded by Devonian and Tertiary sedimentary sequences of mainly continental provenence.

Jan 1, 1989

By S. S. Gajin

The paper deals with parametric vibrations of an axially loaded pile. The dynamic model is derived by means of Hamilton's principle and reduced to a partial differen­tial equation with variable coefficients and corresponding initial boundary conditions, taking into account the influence of the axial force. By means of Galerkin's method, the partial equation is further reduced to a Matheu-Hill's matrix partial differential equation of the second order. Since the problem of the dynamic stabili­ty has been expressed only for standing piles, the paper analyses in detail two stan­ding piles, one which is restreined, whereas the other is hinged at the toe. In both cases it is assumed that head horisontal displacement is prevented. Using Ruunge-Kutt's method, a computer analysis in the time domain is given for the characteristic parameters and possible boundary conditions. The paper analyses the stationariness of the process, as well as the dependance of the critical excitation frequency upon the pile parameters. The results have been illustrated by respective diagrams.

Jan 1, 1989

By D. Mohan

Soft to medium dense silty and clayey soils are found in many parts of India and conventional friction piles have normally been used for foundations of high rise buildings and other structures on such soils. The author investigated the use of Bored Compaction Piles and these have been used on these soils achieving substantial economies in cost over conventional friction piles. Similarly highly expansive clays, commonly known as Indian Black Cotton Soils occupy about 20 percent of the Indian land area. Short bored underreamed piles have been developed for such soils and a very large construction of various types of buildings and other structures have come up on such piles over the last thirty years in various parts of the country. The paper describes investigations leading to the design and development of both these type of foundations.

Jan 1, 1989

By W. L. Cornell

The Missouri Pb ores are the only domestic Co resource being mined and processed for other metals; therefore, they present a viable short-term opportunity for Co production. Lead, zinc, and copper concentrates are produced from the ore. The Cu concentrate can contain up to 30 pct Co and the Pb concentrate up to 15 pct Co. Since Co is detrimental to the processing of the Zn concentrate; the remainder of the Co is rejected to the tailings. The tailings can contain as much as 50 pet Co originally present in the mined ore. Researchers at the U.S. Bureau of Mines have successfully tested on a continuous basis a process that recovers a bulk sulfide concentrate from mill tailings. The concentrate contains up to one-half of the Co and from 50 to 90 pct of the Pb, Zn, and Cu. Concentrate weight represents 10 pet or less of the total tailings.

Jan 1, 1989

By Leszek Hoser

Polycrystalline oxide superconductors that have the perovskite structure, that are oxygen deficient, and that have compositions based. on the so-called. 1-2-3 (YBa2Cu3O7) compound, were investigated.. The materials exhibit a high critical transition to superconductivity at temperatures near 90oK. It was determined that maintaining the oxygen content within the correct range in connection with an appropriate amount of CU ions in the crystal lattice leads to high-critical temperature (Tc:) superconducting properties. High-Tc: superconductors with a critical temperature in the range of 100°K were developed. Further investigations, based. on the theoretical examinations of the origin of superconductivity, have been performed and are discussed..

Jan 1, 1989

By Junbiao Liu

Rutile is mostly produced from placer sands. Its beneficiation from primary deposits has rarely been investigated. However, there is interest in primary deposit because of the depletion of sand deposits. The Zaoyang deposit in China is the only rutile primary deposit currently mined. The plant employs a Tabling-Magnetic process which recovers only 20% Ti02 at a grade of 87%. This study shows that significant improvement on the recovery (52% at the same grade) can be achieved. This study includes a detailed mineralogical examination and the development of a processing flowsheet of the ore. The gangues are primarily amphiboles, garnets, zoisites, and chlorites. The liberation of rutile occurs at about 200 mesh. Gravitational, flotation, and magnetic separations are all employed in the process developed, depending on the mineral characteristics and experimental results. The flotations circuit utilizes benzyl arsonic acid to float rutile and sodium fluosilicate to depress the gangues. This is a new reagent scheme for rutile flotation.

Jan 1, 1989

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By David P. Conover

The effects of stress distribution on pillar stability were evaluated through rock mechanics studies conducted in three underground room-and-pillar coal mines. Results of the three field instrumentation programs are presented to illustrate the use of borehole pressure cells to determine vertical stress distribution in coal pillars at various stages of mine development. Vertical stresses and stress changes are determined using methods developed at the Bureau of Mines. Measured stress distributions are compared against theoretical distributions and possible explanations for observed behavior are discussed. Results indicate that stresses and stress changes calculated from pressure cell data are inconsistent with theoretical values; however, the data are useful for qualitative evaluation of trends over time. Calculated values are found to be sensitive to coal properties and initial setting pressures of the cells.

Jan 1, 1989

By Deepak Malhotra, Linda K. Baltich

The minerals business is dynamic and competitive and the economic viability and/or profitability of any mineral company depends on maximizing recoveries while minimizing costs. In order to achieve this goal, it's essential that you have a clear understanding of the current status, including strengths and weaknesses, of the operation. The authors have developed a systematic approach to plant auditing which we have used successfully at several operations. The strategy presented in this paper can be tailored to fit a wide range of audits. This flexibility is a key feature of the approach.

Jan 1, 1989

The process selection and design aspects to treat primary ore in a new carbon-in-pulp (C.I.P.) plant while utilizing, where possible, existing equipment and infra- structure are discussed. The existing crushing plant, water supply, reagents, laboratory and infrastructure facilities from the heap leach have been upgraded and expanded to meet the C.I.P. plant requirements. The new power supply is from the North Queensland grid system. A series of metallurgical tests was carried out and a review of the data showed that the primary ore was amenable to conventional cyanide leaching. Following feasibility studies, a new process plant which included grinding mills, leaching, and adsorption tanks, thickener, desorption and gold roam facilities was constructed.

Jan 1, 1989

By N. S. Dalal, X. Shi

"It has been recently suggested that the exceptionally high antitumor and antibacterial activity of natural fredericamycin A (FMA) is related to its ability to spontaneously generate the superoxide anion (02-) and hydroxyl (""OH) radicals in aerobic solutions [Hilton, B. D., Misra, R., & Zweier, J. L. (1986) Biochemistry 25, 5533]. With a view to understand the mechanistic details, attempts were made to reproduce earlier electron spin resonance (ESR) evidence for the oxygenated free radical formation in well-aerated solutions of natural FMA in dimethyl sulfoxide and dilute H 20 2• Little or no evidence was obtained for the formation of the 0 2- and methoxy (""OCH3) radicals, while the detected formation of the 'OH and methyl ('CH3) radicals was attributable largely to mechanisms not involving FMA. These results thus reopen the T question regarding the mechanism of its exceptionally high tumoricidal-bacteriocidal activity. This paper reports on an electron spin resonance (ESR) investigation of the formation of oxygenated free radicals in solutions of natural fredericamycin A (abbreviated as FMA) which has recently been reported to be a highly potent anti¬tumor antibiotic (Pandey et al., 1981; Warnick-Pickle et al., 1981). The impetus for this undertaking was provided by recent reports (Hilton et al., 1986; Stinson, 1986) suggesting that the strong tumoricidal activity with high therapeutic—toxic index of FMA was related to its ability for the spontaneous generation of superoxide anion (02-) and hydroxyl (OH) radicals. For example, the suggested mechanism for the formation of 02- by FMA was (Hilton et al., 1986)FMA-OH + O2 FMA-O + H+ + 02-Here FMA—OH is simply the FMA molecule emphasizing the —OH moiety which becomes FMA-O, the free radical rep¬resenting the oxidized form of the drug. While some other highly effective anticancer drugs in current clinical application, such as bleomycin, are also thought to exert their antitumor effects via the formation of reactive drug-based or oxygenated free radicals (Carmichael et al., 1985; Gianni et al., 1983), FMA was considered unique in that only in this case the free radical formation was thought to be spontaneous, rather than through a metal- or an enzyme-activated process (Hilton et al., 1986; Stinson, 1986). Thus it was suggested (Hilton et al., 1986; Stinson, 1986) that FMA could be the forerunner of a new class of anticancer drugs. However, we noted that while the hypothesis seemed plausible, the reported ESR spectral evidence appeared to be ambiguous. Because of the high significance of the earlier conclusions (Stinson, 1986), we undertook a systematic ESR study of the radical formation in FMA solutions, and as discussed below, our conclusions disagree with those reported earlier."

Jan 1, 1989

By Cornwell P. J

The Pajingo ore bodies consist mainly of auriferous quartz veins hosted by a suite of hydrothermally altered andesitic pyroclastics, volcanics and epiclastic sediments. Scott lode, the main economic deposit in the area, lies in a zone of major structural disruption and contortion. High grade gold and silver mineralisation is selectively mined by open pit methods. Standard grade control techniques and extraction methods were adapted to minimise mining dilution and to maximise metal recovery. Basic blending of grade ranges at the crusher has produced an average 10 gram/tonne gold head grade. The estimation of ore reserves calculated by both standard polygonal and geostatistical methods proved acceptable. Mineable reserves when compared to in pit reserves defined by blast hole drilling, indicate a decrease in tonnes and an increase in the grade resulting in an acceptable comparison of the total ounces of contained gold. The ore reconciliation of mined against milled ounces indicates that both ore reserve and grade control models underestimate the metal content in the orebody. Sampling techniques are being examined in an attempt to reduce this discrepancy.

Jan 1, 1989

By Frederik P. Agterberg

During the past 20 years, methods of multivariate statistical analysis have been developed on mainframe computers for the integration of geological, geophysical, geochemical and LANDSAT data in mineral resource appraisal. At present, it is becoming increasingly feasible to perform mathematical image analysis of digitized patterns on microcomputers. This has led us to develop a new method of statistical pattern integration for mineral exploration. In this paper, the new method is used to outline, by means of posterior probabilities, exploration targets within small areas of which the prior probabilities for occurrence of new mineral deposits had been estimated by multivariate analysis.

Jan 1, 1989

By Donald R. Sadoway

Fused salt electrolysis is used extensively in the primary extraction of metals (electrowinning), in the refining of metals (electrorefining), and in the formation of coatings (electroplating). In the case of rare earths, fused salt electrolysis competes with nonelectrochemical processes to make the same products. However, fused salt electrolysis has the potential to produce these metals in a variety of technologically useful forms: thin films and epitaxial layers, powders, and a variety of nonequilibrium structures. The theory and practice of fused salt electrolysis as it applies to the extraction, refining and plating of rare earth metals are described. The potential of fused salt electrolysis to synthesize advanced materials containing the rare earth elements is assessed.

Jan 1, 1989

By Hll J. K, Zhang Y. G

The wear mechanisms of impregnated diamond drill bit matrices are complex and believed to be the key point in solving drill bit self-sharpening problems. A method has been developed to find the change in c,, the wear rate of matrices having different fracture toughness K_ at the increment of drill pressure P. The worn surfaces of specimens were placed under a scanning electron microscope to examine the wear patterns and wear mechanisms at different pressures, and were compared with the worn surface of a practical drill bit. A model is proposed that within a wide range of pressures there exist two different wear mechanisms and three wear regions for cemented car- bide matrix materials. In region one (linear region), at low pressure, the major wear mechanism is plastic deformation in which the preferential wear of the binder phase of the matrix results in the loss of WC, tung- sten carbide particles. Wear rate is controlled by hardness, H as Archard's formula predicts. Wear enters region two and three (non-linear region) simultaneously as pressure is being increased. Consequently, wear transfers to fracture mechanism in which micro-fracture occurs at the root of wear grooves and the material is removed mainly in piece and mass. It has been shown fracture toughness K,, plays a more important role than hard- ness H. It is concluded that for a specific drilling condition, the pressure on the matrix should be carefully controlled and a balance between hard- ness and toughness of the material is essential for a steady drilling Condition.

Jan 1, 1989

By Randal J. Barnes

The nonlinear network optimization algorithm developed in this paper solves the following mine ventilation design problem: find the location and size of all fans and regulators which minimize the overall system power consumption while satisfying all physical, legal, and operational constraints. This work includes the formulation of the problem within the framework of mathematical optimization, the development of the computational theory, and the creation of an efficient solution methodology. The algorithm has been implemented on a microcomputer, and a small but representative example is included. The algorithm presented in this paper has four limitations. First, the optimization process is for a single point in time: the dynamic nature of a mine ventilation system in an evolving mine is not directly addressed. Second, the topology of the ventilation network is required input information. The mathematical algorithm does not optimize the size or location of the mine ventilation airways; however, the post optimality analysis techniques can be used to aid in topological decisions. Third, the problem is formulated using volumetric flow; thus, heat and moisture transfer are ignored. Fourth, the capital cost of ventilation equipment is not included in the formulation.

Jan 1, 1989