Search Documents

By D. B. Dreisinger, H. J. Sohn, J. S. Sohn, G. A. Kordosky

The transport of lithium through a supported liquid membrane was studied with a mixture of D2EHPA and TBP in kerosene as a mobile carrier. In the flat- sheet supported liquid membrane(SLM) system, experiments were carried out to investigate the effects of concentration of mobile carriers in the membrane solution, hydrogen ion in the feed solution, and temperature on the transport of lithium. Experimental results agreed well with a transport model for permeating lithium across the liquid membrane. The permeation rates of lithium can be explained in terms of diffusion of a Li-complex through the membrane phase. For a practical application of an SLM method, a hollow fiber module has been used and lithium can be concentrated more than three times in 24 hours.

Jan 1, 1993

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By Po-Wei Tun, Kuen-Yuh Wu, Tso-Min Shih, Hsi-Chiang Fang

The purpose of this study is to investgate the coal dust explosion characteristics and to search for the prevention methods of the coal dust explosion as well as the propagation of the explosion flame of the middle-bearing coal formation in Taiwan by an open type coal dust explosion apparatus in laboratory. The coal samples were taken from the typical middle-bearing formations of the Sam-Ming,Tai-Ho and Lee-Fong coal mines The rock dusts, the free water mixture with coal dust samples and the interval clean out the coal dust in the testing chambers were applied for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1993

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By J. A. Brierley, C. L. Brierley, R. C. II Blake, S. McGinness

A principal long-term goal of this laboratory is to achieve a detailed understanding at the molecular level of the microbial-dependent solubilization of minerals. Three recent advances in this research are summarized. (i) An in situ electrolytic procedure is described whereby large quantities of autotrophic iron-oxidizing organisms may be achieved for fundamental or applied studies. Over 600 grams wet weight of Thiobacillus ferrooxidans were harvested from a single 55-gallon growth vessel. (ii) A basis is presented for classifying some 70 different iron-oxidizing bacteria into one of 4 categories, depending on the type of redox-active electron transport proteins expressed during aerobic respiration on reduced iron. Comparative spectroscopic analyses indicated that different electron transport mechanisms exist in different genera and species of acidophilic bacteria that respire on iron. (iii) A method is introduced to investigate the binding interaction between bacteria and minerals, based on changes in the electrokinetic properties of the two species. Preliminary experiments indicated that the electrophoretic mobilities of pyrite and Thiobacillus ferrooxidans were both altered when the two colloid particles were mixed prior to the actual electrokinetic measurement. The need for more basic information regarding all aspects of the microbial-dependent solubilization of minerals is evident.

Jan 1, 1993

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993

By Peter N. Gabby

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 27,034-hectare Steel Mountain/Yuba River study area and the 16,544-hectare Breadwinner study area. There were approximately 535 lode and placer claims in or partially in the Steel Mountain/Yuba River study area, and 84 lode and placer claims in or partially in the Breadwinner study area. In the Atlanta and Rocky Bar mining districts, both adjacent to and in the Steel Mountain/Yuba River study area, 30,232.4 kg (972,000 02) of gold and 62,838.3 kg (2,020,000 02) of silver had been produced. Most of this production came from outside the study area. Placer properties adjacent to (and a few in) the Breadwinner study area had production of 93.1 kg (2,992 oz) of gold and 20.0 kg (642 02) of silver. Twelve properties in the Steel Mountain/Yuba River study area have potential for resources; eleven have alteration and/or mineralization similar to that found at Atlanta with potential for gold, silver, and tungsten resources, and one has alteration and mineralization associated with polymetallic vein type deposits with potential for gold, silver, copper, lead, zinc, and tungsten resources. Adjacent to the study area, large bars of gold-bearing gravel can be found along the Middle Fork Boise River. Four properties in the Breadwinner study area have potential for mineral resources; one has alteration and mineralization associated with skarn, polymetallic vein, and, possibly, copper-molybdenum and molybdenum porphyry types of deposits; two have alteration and metal assays associated with polymetallic vein, and possibly copper-molybdenum and molybdenum porphyry types of deposits; and one has alteration and mineralization similar to that found at Atlanta. These four have potential for gold, silver, copper, lead, zinc, molybdenum, and tungsten resources Adjacent to and extending into the Breadwinner study area are large bars of gold-bearing gravel along North and Middle Forks Boise River.

Jan 1, 1993

By R. E. Molnar, P. A. Riveros, V. M. McNamara

"This paper describes some recent research done at CANMET in the areas of ion exchange and A VR (Acidification- Volatilization Reneutralization), as applied to the recovery of gold and cyanide, respectively. It also discusses the ways in which these two technologies may be combined in order to minimize the environmental impact of gold milling operations and optimize reagent usage. IntroductionGold milling operations can essentially be divided into those that carry out a liquid/solid separation after leaching and those that recover gold directly from a leach pulp. The former produce a barren solution which may contain considerable amounts of cyanide, either free or cornplexed with metals. The latter produce a similar solution but this is now part of a slurry rather than a clear stream. Due to its toxicity, any excess cyanide must be destroyed before the effluent is discharged into the environment. Ideally, this should be (and sometimes is) accomplished by natural degradation. However, in many cases natural degradation alone cannot remove the last traces of rnetallocyanide compounds from the effluent and , as a result, most Canadian gold producers utilize a supplementary chemical oxidation system. This not only increases the operating costs, but concerns have also arisen in recent years about the formation of ammonia as a result of the chemical oxidation of cyanide (via CN--CNO--HCNO-NH3) ·"

Jan 1, 1993

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By H. Braun, T. Kind, K. Gloe, D. B. Dreisinger, H. Stephan, O. Heitzsch, G. A. Kordosky

Municipal garbage incineration processes with coupled wet flue gas cleaning systems generate effluents containing toxic heavy metals such as mercury, zinc, cadmium and copper. The separation of these metal ions from the obtained scrubbing solutions is possible using liquid-liquid extraction. Extraction studies has been performed both with commercial extractants Aliquat 336, di(2-ethylhexyl) phosphoric acid and novel chelating agents as acyl thiourea and lipophilic oxathiaaza alkanes. Advantages and disadvantages of the investigated extraction systems are discussed. The paper reports on the basic research as well as on the testing in a laboratory scale.

Jan 1, 1993

By Y. J. Wang

A subsystem-based approach to the characteristic curves for a multiple fan ventilation system is presented. The ventilation variables and their relationships associated with a fan branch are considered as a subsystem of the multiple fan system. For each subsystem, the solution curve is generated by replacing the fan with a hypothetical pressure source or, alternatively, by adding a hypothetical pressure source without removing the fan. The projection of the solution curve onto the coordinate planes results in two classes of subsystem characteristic curves: pressure-vs.-quantity and quantity-vs.-quantity. The subsystem characteristic curves are described and illustrated through example ventilation systems. These curves are also discussed using the network equations of a general multiple-fan system.

Jan 1, 1993

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

By McKenzie C. K, Stewart R. S, Simpson J

Blast control in small scale underground mining leads to improved fragmentation control, improved control over overbreak and dilution, and the optimisation of drilling and charging operations. Greatly improved control can be achieved through blast monitoring, to confirm proper implementation of blast designs and blasthole charging. Further improvements can be achieved through simple modelling, enabling blastholes to be placed in the correct locations and charged with the correct weight and strength of explosive. Improved design can be shown to significantly reduce overbreak and dilution, and even ground support costs. In one mine in Quebec, open stopes of widths varying from 2.5 metres to four metres and dipping at 36¦ to 38¦ were designed to achieve zero dilution using open sloping blasting practices. The first stope designed in this manner was monitored in detail and achieved its objective.A method for contouring damage around blastholes is presented as a basis for selection of drilling patterns, with particular application to the control of overbreak and dilution. Contouring can be used to provide reliable estimates of either overbreak or damage (where rock is broken het reynainc in nlarr)

Jan 1, 1993

By Brian Maroney

In this paper an overview of the California Department of Transportation's (CALTRANS) bridge design criteria is presented. Special emphasis is focused upon seismic design and retrofit criteria. Topics include earthquake load definitions, foundation and structure type selection, structural earthquake analysis, and structure behavioral requirements.

Jan 1, 1993

By W. K. Choi

Stainless steel exposed to wet environments at ambient temperature is subject to the formation of a surface biofilm. Depending upon the prevailing environmental conditions (dissolved oxygen, pH, Eh, concentration of cationic/anionic species), the biofilm may stimulate corrosion through formation of differential aeration zones and concentration cells. Corrosion significantly impacts the United States economy, since on a yearly basis, corrosion induced losses are estimated to be over $200 billion. A large portion of this corrosion is imputable to bacterial activity, and basic information is needed for a better understanding and control of the biocorrosion phenomenon. The present study has investigated the influence of Thiobacillus ferrooxidans in the corrosion of American Iron and Steel Institute (AISI) 304, 316 and 416 stainless steel samples. The formation of biofilm and microstructural changes on the surface of stainless steel samples and their weldments were assessed by microscopic examination, and the changes in the mechanical properties by stress-strain measurements. The significance of the results will be discussed.

Jan 1, 1993

By Kerry Spickelmier

The only nickel smelter and the only active nickel mine in the United States is Glenbrook Nickel Co., a joint venture (50% each) of Cominco Resources International Ltd. and Cominco Ltd. In 1989, with the nickel price riding high between $2.30 and $2.70/kg ($5 and $6/lb), Glenbrook seized the opportunity to purchase and recommission a southwestern Oregon ferronickel smelter and the adjacent nickel-ore mine. This Douglas County site is only about 97 km (60 miles) due east of the Pacific Ocean, and California's border lies a similar distance to the south. Hanna Mining Co. had closed the operation in 1987. And the following year, the equipment had been largely stripped for salvage value. From November 1990 through August 1992, the mine supplied an average 5 kt/d (5500 wet stpd) of ore. Currently, with import ore supplying 40% of the smelter feed, the mine's daily tonnage averages 4.2 kt (4600 wet st). From November 1990 through August 1993, the mine has delivered 2.1 Mt (2.3 million st) of ore grading 1.22% nickel with an average moisture content of 26%. Buffaloed nickel? A nickel is not worth what it was in 1989 and neither is ferronickel, with recent prices hovering around $1.13/kg ($2.50/lb). To survive, Glenbrook has focused on increasing smelter production to lower its operating costs. And this strategy has triggered several bold moves: • a new, $30 million, port facility and • a 10-year importation contract for ore from New Caledonia, an island approximately 1000 km (625 miles) east of Australia. For a Glenbrook update, a May 25, 1993 visit was made to the company's Oregon operations - the mine and smelter near Riddle plus its new Coos Bay port facility. Unfortunately, as the rain came down that day, so did news of another temporary shutdown. The previous suspension had lasted from Dec. 20, 1992 until Feb. 22, 1993. Barely three months back to work on a wet May afternoon, more than 250 of Glenbrook's approximately 300 employees contemplated yet another shutdown, effective July 31, 1993.

Jan 1, 1993

By C J. Hogan

Increasing demand for fine grinding to improve mineral liberation and metal recovery and the need for stricter control of the environmental impact of tailings deposition poses problems for tailings disposal. This has led to an increasing number of investigations of properties of tailings and their disposal. This paper describes laboratory model testing undertaken on Macraes mine flotation tailings to provide information on tailings behaviour under conditions of subaerial deposition. The in-place density or 'dry density' of the impounded tailings and the impoundment depth relationship are important for utilisation of the available impoundment storage facility and results of dry density to depth relationships are given for the Macraes mine tailings impoundment.

Jan 1, 1993

By J. Wild, M. Ounpuu, G. Chevalier

"The requirements for a finer grind at Heath Steele have resulted in the investigation of agitated milling as a cost effective alternative to conventional tumbling ball mills.The grinding unit is a vertically agitated, or stirred ball mill. Grinding occurs as the result of the motion of a single vertical rotor equipped with protruding pins which impart a stirring action to the ball charge. A comparative evaluation of a 30 kW SALA Agitated Mill (SAM), and a 1.5 m x 2.5 m copper-lead regrind ball mill has been conducted at Heath Steele.An overview of agitated milling as it applies to the reduction of sulphide ore will be the primary topic for discussion. Specific parameters including energy efficiency, media consumption, operating costs, and the mechanical aspects of the SAM operation will be presented.Evaluation of the agitated mill has shown that improved grinding performance at much lower work indices than those of the conventional ball mill is possible. Media consumption has proven to be comparable on an average g/kWh basis, but the mechanical availability of the mill has been low.INTRODUCTIONConventional tumbling ball mill grinding has proven to be an energy inefficient process. Energy losses occurring within the ball mill itself can be attributed to particle friction without breakage, kinetic and potential energy losses, plastic and elastic deformation and the production of heat and sound (Lynch, 1977). It can be generally stated that a certain amount of the input energy will be converted to another form as a necessary by-product of particle breakage. Theoretical interpretation of experimental results indicate that the energy required for breaking the ore particles in a ball mill varies between I% and 25% of the total energy input (SME, 1985)."

Jan 1, 1993

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993