Search Documents

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By M. R. Moon

The mine fire at Wilberg Mine in 1984 reached the surface resulting in the failure of the vertical ledge forming the roof and entrance for three main intake portals. The fallen material was covered with a concrete cap to seal the air from the mine. As the mine was recovered and ventilation pressure was placed on seals on the perimeter of the fire area, the concrete capped rubble proved ineffective. Due to the steep and rugged terrain and the inaccessibility to the portals from underground, horizontal holes were drilled into the portal entries and three seals were placed remotely. The seals in conjunction with pressure balancing the seals around the perimeter of the fire area resulted -in the control of the mine fire.

Jan 1, 1993

By Nguyen T. T, Williams A. M, Siauw T. H

During the last 20 years the CSIRO Division of Manufacturing Technology, through its research and development program, has made a substantial contribution towards understanding the pressure die casting process. Much of this work focused on the hot chamber die casting of zinc, where the importance of achieving optimum flow of metal into the die cavity, combined with the correct thermal balance of the tool, is critical to the production of high quality castings. Having developed a fuller understanding of the heat and fluid flow occurring in the pressure die casting process, CSIRO sought to make this information available to the industry in a form where it could be readily used by die casting engineers. This led to the development of DMT-CASTFLOW and DMT-CASTHERM, two unique, PC-based, die design software packages. DMT-CASTFLOW provides facilities for designing running and gating systems while DMT-CASTHERM enables the die designer to optimise the cooling and/or heating requirements of the die. These two packages are now being sold internationally. This paper will describe some of the major features and benefits that can be derived by using DMT-CASTFLOW and DMT-CASTHERM panicularly in the design of zinc pressure die casting dies.

Jan 1, 1993

By Ian McFeat-Smith, Odd G. Askilsrud

Introduction Given the mountainous nature of the local igneous terrain, hard rock tunnelling plays an important role in the development of Hong Kong's infrastructure. In 1990, tenderers for two tunnel projects were encouraged to consider using hard rock TBMs, the territories' first. As a result the 7.5km long, 3.56m diameter Tolo Effluent Tunnel and the 5.3km long, 4.8m diameter Hong Kong Electric Cable Tunnel were excavated by hard rock TBMs. The successful completion of both projects in 1992 should make the TBM method an attractive construction alternative for planned, upcoming projects in Hong Kong. Tunnelling Conditions Tunnelling solutions are frequently adopted in Hong Kong due to the intensity of development, lack of flat landscape and proximity of mountainous terrain to the main centers of population. This is carried out primarily in granites or granitic-type rocks which surround Victoria harbour, and to a lesser extent in the outlying volcanic rocks which include extremely hard tuffs and lavas. Tunnelling will generally take place in granitic rocks, normally about 100-250 MPa in strength, and with an average joint spacing of 0.3m and a quartz content of 30-

Jan 1, 1993

By Gao H

Based on the author's research and plant practice experience of the last decade, several technological approaches have been developed to increase the recovery of gold and silver associated with sulphides. This paper gives a general discussion of some technological problems encountered in this area in five aspects and introduces the different approaches employed in three typical mineral processing plants to increase recovery of associated gold and silver. On the basis of studying occurrence characteristics of gold and silver minerals in sulphide ores and of determining loss locations of gold and silver on flotation process, a remarkable improvement on the recovery of gold and silver in all these three plants was made by choosing proper grinding fineness, using combined collectors of good selectivity, properly decreasing the grade of main metal concentrates, making reasonable arrangement of the products of main metals, or a combination thereof.

Jan 1, 1993

This paper illustrates the application of numerical modeling methods, in conjunction with limit-equilibrium techniques, to the location of critical slip surfaces in slope-stability problems. Initially, the Spencer slice-based method of analysis is introduced, together with a dynamic-programming algorithm for slip-surface location. This limit-equilibrium method is assessed critically through the use of an illustrative problem. The technique is then extended to locate the critical slip surface for a similar slope, but with more complex constitutive and yield relationships for the material comprising the slope. To this end, the use of the stress field generated from a finite-difference program, together with a dynamic-programming search routine, is presented as an advanced technique of slope-stability analysis for engineers.

Jan 1, 1993

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

Modern coal cleaning technologies have allowed coal preparation facilities to become quite efficient at removing sulfur compounds, waste rock and low grade coals from run of mine coal. Up to 50% of the raw mined coal stream may end up as refuse, particularly when the coal originates from longwall mining operations, or is high in partings, rock and impurities. The refuse materials vary from coarse materials removed by physical screening to very fine materials removed by floatation and density separation processes. Coal refuse piles are also known by a variety of other names including "waste dumps", "gob piles" and "slate dumps". The potential hazards of improperly reclaimed refuse include contamination of surface and groundwaters by acidic leachates and runoff, erosion and sedimentation into nearby watersheds, spontaneous combustion, disturbance of topsoil borrow areas, and damage from landslides should large slope failures occur. Many of these problems have been particularly acute for abandoned refuse piles, and modern regulations attempt to minimize the environmental impact of coal refuse disposal operations.

Jan 1, 1993

The adsorption of gold onto activated carbon in iodide solutions has been studied. The adsorption rates were determined as a function of temperature, salt concentration and pH as well as activated carbon concentration. A kinetic model was also developed for the adsorption. The adsorption rate was believed to be controlled by a mixed mechanism of film diffusion and pore diffusion, but the film diffusion had a major contribution to the overall rate. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1993

By Fuerstenau DW

The flotation of pyrite in ethyl xanthate solutions is presented along with electrokinetic results. The results have been analysed in view of recently published thermodynamic calculations as well as other published data on the pyrite-xanthate system including adsorption and voltarnmetry studies. The flotation response of pyrite in xanthate solutions is characterised by two maxima, one at pH 4 and the other at pH 8-9. The acidic maxima is also associated with a reversal in the electrophoretic mobility of pyrite, probably due to the formation of ferric xanthate on the pyrite surface through chemisorption of xanthate ions while the basic maxima is not associated with major changes in the mobility and flotation at this pH can probably be attributed the adsorption of dixanthogen. It is concluded that there is not sufficient experimental evidence to conclusively attribute the lack of flotation response in solutions at near neutral pH to any particular phenomena, either kinetic or thermodynamic.

Jan 1, 1993

By Jim Morris

This paper will describe the excavation of a 5.4 percent decline at the Montanore Project for Noranda Minerals Corporation. The 5.3 m by 4.9 m tunnel was driven to provide access for the exploration of a major copper-silver deposit. Soft ground and conventional drill-blast mining were used on the 4,270 m tunnel. Ground support consisted of steel sets and concrete in the soft ground and pattern rockbolts providing the majority of the rock support. A special feature of the project was the use of conveyor haulage in conjunction with the drill-blast excavation.

Jan 1, 1993

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By Ranklin W. J, Swinbourne D. R

Lead blast furnace slags contain typically 10 - 20 mass per cent Zn. The zinc can be recovered by slag fuming, in which a powdered coal/air mixture is injected into a molten slag bath. Volatilised zinc is recovered as zinc oxide from the gas and processed hydrometallurgically to produce zinc metal. The ISASMELT continuous lead smelting process in operation at Mt Isa produces a slag containing about 12 per cent Zn which is currently granulated and stockpiled. This slag could flow to a further bath-smelting reactor for continuous zinc fuming. Rather than collecting the zinc as fume from such a process, one option would be to recover it using a lead splash condenser. The success of this operation would depend on the composition of the gas produced, in particular the concentrations of gases capable of reoxidising zinc vapour, viz, carbon dioxide and water vapour. The aim of this investigation was to determine the smelting conditions for a bath-smelting process such as ISASMELT or SIROSMELT which would produce a gas similar in composition to that from an Imperial Smelting Furnace by thermodynamic modelling of the process using the CSIRO Thermochemistry System. It was found that such a gas could be produced if coal injection and oxygen enrichment of the combustion air to at least 40 per cent 02 were used. However, the off-take gases must be conditioned by addition of methane to reduce the water vapour content to acceptable levels. An addition rate of ten per cent of the off-gas flowrate was found to be adequate. Addition of methane to the off-gas had the added advantage of cooling the gas from the bath temperature to a temperature suitable for normal lead splash condenser operation.

Jan 1, 1993

By R. E. Gertsch

A mobile-modular carbon adsorption mill design and operation for small to medium sized heap leach precious metal mines is presented. In the mobile-modular strategy, charcoal columns with adsorbed metal move from small strategically located carbon adsorption loading stations to a central stripping facility and back. The design has many advantages: 1) It scales-up from pilot plant to full production. 2) It has low capital requirements. 3) Operational costs are competitive with other systems. 4) Mill production can react quickly to changes in ore grade or property area. 5) The solution circuits are simple and easy to maintain. 6) Charcoal damage is reduced.

Jan 1, 1993

By Animesh Jha

Univariant diagrams are constructed for the reduction of nickel and cobalt oxide and sulphide minerals. The results from the carbothermic and hydrogen reduction of sulphide minerals are compared. The importance role of lime and calcium sulphate in controlling the emission of sulphurous- gases during reduction reaction is also explained. The mechanism of carbothermic reduction of nickel sulphide is explained by examining the sulphur exchange and reduction reactions. The phase equilibrium relationships that determine the formation of multicomponent liquid are characterised. Also the governing equilibria for inert atmosphere calcination- roasting of nickel and cobalt sulphide minerals are also described for the metallization of nickel and cobalt.

Jan 1, 1993

By H. Peter Knudsen

In most open pit gold mines, ore-waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. This paper focuses on the source of the conditional bias. While it is true that high grades and "outliers" can induce a bias, they may not be the only reason for the persistent bias seen at many mines. In this paper, it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1993

By Steven A. Whittle, Robert E. Cook

Years ago, personal computers (PC) were pricey devices destined for who knows where in the process industry. Now their use runs the gamut from low end data acquisition systems to high performance windows into the process area. Their applications range from CAD, CAM, CIM, and CAE to factory floor scheduling, process planning QC, facility management, cell control, and publishing. This discussion traces the evolution of a zinc plant's control automation program beginning with a PC as an operator interface and migrating to higher level work stations. Included in this paper will be a discussion of an Open Industrial System and the role PCs have played in this facility.

Jan 1, 1993

By Stavros A. Argyropoulos

Exothermic mass transfer takes place in various areas involving metallic systems, ranging from liquid metal processing operations to the growth of thin films in microelectronics. The formation of intermetallic compounds plays an important role in the exothermic mass transfer of metallic systems. Two types of exothermicity are identified , namely , Microexothermicity and Macroexothermicity. The former is encountered when small amounts of metals are mixed, while the latter is exhibited when a solid metal in a lump form is added into liquid metal. In this paper two types of exothermic mass transfer in metallic systems will be presented and reviewed. Mathematical modelling work for these types of exothermic mass transfer will be analyzed.

Jan 1, 1993

By Ian Misich

A research programme has been undertaken to evaluate and predict the effect of total extraction of coal by underground methods on the superimposed strata, aquifer systems and ground surface in the Collie Basin. Western Australia. The research work has integrated comprehensive field monitoring of surface and subsurface subsidence with empirical, analytical and physical modelling in an effort to develop an effective predictive tool which can be used in all mining scenarios. Early results indicate that although each method has certain limitations, this approach has enabled the researchers to develop a very good understanding of the subsidence mechanisms from the mine panel through to the surface in the weak, water saturated sediments in the Collie Basin. Given that both subsurface and surface subsidence characteristics have tied in well, greater confidence can be held for predictions made by representative models.

Jan 1, 1993

By James S. E

Financial risk of environmental problems is the key to many important business decisions within the mining industry. Massive uncertainty makes it difficult to choose a strategy for managing environmental problems to reduce corporate financial exposure to environmental impairment. A correct and practical method exists to clarify the risks and help make decisions. A case study on an insurance problem illustrates the method.The approach used is to translate existing data on environmental problems into probabilistic expressions of financial risk, and organise the expressions to reveal alternative solution strategies for the insurance problem.

Jan 1, 1993