Search Documents

By Ken Norris

"Campbell Mine which has been in continuous operation since 1949 has undergone numerous operational changes in the past 3 years. This paper describes the process changes which have occurred at the Campbell Mill since 1991. The paper discusses the engineering, construction and startup of the effluent treatment circuit, the new oxide filtering and merrill-crowe precipitation circuit, and the changes to the pressure oxidation circuit. Particular attention is paid to startup problems and solutions to these problems. A review of the benefits and results of these process changes is also discussed. Future changes are also briefly reviewed with anticipated goals and expectations.IntroductionCampbell Mine is a gold mine 100% owned and operated by Placer Dome Canada. It is located in Balmertown, Ontario which is located 300 kilometres northeast of Winnipeg, Manitoba. The Campbell Mine has been in continuous operation since 1949, producing nearly 8,000,000 ounces. In 1993 Campbell Mine is budgeted to produce 289, 750 ounces of gold at a cash cost of $157 US/ounce. Daily mill tonnage is budgeted for 1,430 tons/day but has milled as high as 1,600 tons/day on a consistent basis. Recovery in 1993 is 93.4% and is budgeted to average 94.5% in 1994.In the 1992 edition of the proceedings of the Canadian Mineral Processors conference I described the changes that were made at Campbell starting in 1989. This paper continues where the 1992 paper ended and discusses the changes to the Campbell mill since that lime. The changes to Campbell since January 1992 have been numerous with capital expenditure in the mill exceeding $14.1 million. This paper describes three primary projects since that lime: the effluent treatment project ($5.5 million), the oxide leach/filtering and merrill-crowe project ($4.6 million) and the pretreatment project ($2.81 million). The focus of this paper is to highlight the justification of each project, the design and engineering, and some of the initial operational problems and solutions applied to those problems."

Jan 1, 1994

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By John G. Oldsen

Passive cable bolting and active cable trusses have been used in roof support for more than two years Excellent roof control has been experienced by many coal operations. This paper covers the new and innovative developments in cable support systems and their application in mines. Multiple cable bolts, tensioned cable bolts, coal rib wrapping, and other cable applications will be covered.

Jan 1, 1997

By Donald W. Gentry

The recently established SME-AIME Education Board has completed its first full year of operation, and its six constituent committees-Accreditation, Career Guidance, Continuing Education, Educational Statistics, and Scholarship-have been extremely active in identifying and initiating programs to serve the educational needs of the Society of Mining Engineers and its members. The Continuing Education Committee-primarily concerned with the needs and problems associated with providing a continuing education program for SME members-is responsible for: (1) determining the need for short course offerings; (2) developing needed courses, along with new means and opportunities of presentation; and (3) scheduling and evaluating course presentation. In response to this charge, the committee has sponsored two short courses at the SME-AIME Fall Meeting in St. Louis and three short courses at the AIME Annual Meeting in Denver. Its major effort, however, has been directed toward the 1978 SME-AIME Fall Meeting to be held in Orlando, Fla., where 18 days of short-course instruction have been scheduled. A portion of these courses will be presented prior to the meeting, with the remainder to be presented in Nassau, Bahamas, immediately following the meeting.

Jan 7, 1978

By T O Aspinall

The Australian mineral industry involves a diverse range of expertise and skills. Within that, the mining industry, representing mine planning, mine management and equipment operation, has capital intensive, high productivity equipment and a small but skilled workforce. Continuing education for all personnel in the workforce after formal school courses will be an important contribution towards improving competitiveness. The non-tertiary sector represents a significant proportion of the workforce and requires as much attention as the tertiary educated group. Competency Based Training is now being developed for the mining industry in Australia under the National Training Board and the mining industry is well represented in establishing standards and curriculum. TAFE is a major source of accredited courses but some mining companies are also developing internal courses not necessarily for external accreditation. Articulation of such accredited courses to tertiary mining engineering courses has been considered. The education and training of equipment operators through continuing education requires attention to operating skills, an understanding of the productivity factors under the direct influence of the operator and providing product quality to the customer. The education and training of mining engineers has been widely covered and continuing close involvement of the mining industry is required to ensure well balanced courses in technical and interpersonal skills as well as motivation to continue learning for life. Postgraduate research is a part of continuing education but the mining industry has to continually address the adequate recognition of post-graduate qualifications for the increased technical or management expertise and the development of better analytical and problem solving skills which can be directed towards improving competitiveness. More attention has to be paid to providing adequate financial incentives to attract suitable students, particularly after attaining some experience, and to address their professional career path with a company so they are not significantly disadvantaged by undertaking post-graduate studies. The Chartered Professional Engineer status as provided by The Institution of Engineers, Australia to qualified candidates is being considered by The Australasian Institute of Mining and Metallurgy as a further recognition of a member's specific expertise and competence in mining and metallurgical engineering. Continuing education plays a major part in the maintenance of the expertise and competence required for a professional engineer to develop and also to retain chartered status. Continuing education will be a significant part of the education and training of all the mining workforce towards improving the competitiveness of the mining industry. The major challenges will be the motivation of all towards lifelong learning and the integration of the various programs towards providing the opportunity for a steady and satisfying career progression.

Jan 1, 1994

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

By Emmet K. Oslen

Kaiser Steel Corporation, the pioneer steelmaker on the Pacific Coast, was founded by the late Henry J. Kaiser. In 1944 the Company purchased from the Southern Pacific Railroad an iron ore property 200 miles east of Los Angeles known as Eagle Mountain. Today the domestic operation of Kaiser Steel Corporation consists of the iron mine at Eagle Mountain; two coal mines, one each in Utah and New Mexico; an integrated steelmaking complex at Fontana, California; and several steel fabrication and erection facilities along the west coast. Kaiser Steel also has interest in Hamersley Iron, Ltd., Australia, and Kaiser Resources, Ltd., British Columbia. Eagle Mountain Mine is located about 80 miles east of Palm Springs and adjacent to the southeast corner of Joshua Tree National Monument. The area is one of the most arid in the world averaging only two inches of rain annually. Geologically, the mine is at the western edge of the Basin and Range Province which covers about one-half million square miles of the western United States. The Province is typified by north to northwesterly trending fault block mountain ranges separated by sediment filled valleys, Production has totaled over 82 million tons of finished products since the first shipment in June, 1947. Over 500 million tons of material have been mined from the deposit to date. Eagle Mountain Mine is noted for the pioneering use of the largest and most up to date equipment to mine and process its ore. In 1961 Eagle Mountain received the first fleet of 100-ton haulage trucks in the mining industry. There were thirteen semi-trailer units in the fleet. The first 12 to 17-yard size shovel in the mining industry was placed in operation at Eagle Mountain during 1962. Rotary drilling was introduced at Eagle Mountain in 1954 to replace churn drilling. Eagle Mountain was the first major mine to use metallized slurry when three aluminum slurries were introduced for primary blasting in 1962.

Jan 1, 1972

Like it or not, CPD is upon us. As from 1 January 2006, all registered engineering professionals, i.e. professional engineers, professional engineering technologists, professional certificated engineers and professional engineering technicians, were required to undertake CPD in order to keep their professional registration current. The rules regarding CPD have been gazetted under Government Gazette No. 28328, Board Notice 131 on 23 December 2005, and they also appear on the ECSA website?www.ecsa.co.za. For the convenience of our members they are reproduced in full in this issue of the SAIMM Journal.

Jan 1, 2006

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By I M. Platten

Narrow reef gold deposits are generally less than 4 m in width and relatively complex geological phenomena. They often display variable geometry, attitude, continuity and internal architecture. Economic grades are mostly restricted to specific structural domain(s) and localised within discrete ore shoots that have a nuggety internal grade distribution. On account of the often extended history of geological events, the specific factors localising gold-rich domains are likely to be unique to a particular mine or even reef. These features lead to a high resource risk and require careful management during both evaluation and mining. The gross form, location and global continuity of gold reefs can generally be determined from surface diamond drilling leading to the definition of Inferred Mineral Resources. It is likely that for the definition of Indicated and Measured Mineral Resources underground development and/or close- spaced diamond drilling will be required. Understanding geometry and continuity permits the resource to be more effectively managed, lowering risk/uncertainty. This in turn will allow for well-informed financial and operational decisions. Most importantly, project expectations and milestones can be set at achievable levels.

Jan 1, 2008

By Lovett EP, Johnson CR, Dunlop GA

Seven streams of a low tonnage pilot plant operation on Cu/Pb/Zn ore from the Golden Grove Project were continuously assayed using an AMDEL In-Stream Analysis (ISA) system. The ISA instrumentation is briefly described as is the calibration procedure employed. The successful application of this instrumentation in the dynamic environment of a pilot plant operation is discussed. The operational sequence of the Golden Grove pilot plant is outlined along with the original project objectives and how they were achieved by the implementation of ISA. Results for the different complex flowsheets used are discussed, followed by the perceived benefits of installing such equipment in this operation.

Jan 1, 1986

By J. G. Zafiratos

The leaching of a Greek low-grade manganese dioxide ore, not amenable to conventional mineral processing operations, was studied using a mixed culture of Thiobacillus sp. bacteria. The experiments were carried out in specially designed continuously aerated and stirred tank reactors arranged in two-tank series. The first tank of each series was loaded with an elemental sulfur culture suspension while the second was loaded with a manganese ore high density slurry. The bacterial culture had been previously adapted to grow on elemental sulfur and also in the presence of manganese ore and dissolved manganous ion. A two level full factorial design was constructed in order to study the effects of the ferric ion concentration in the leach solution, the "elemental sulfu weight to ore weight" ratio, the ore pulp density and the composition of the dispersed gas. The responses which were investigated included percentage manganese recovery, co-dissolution of iron and manganese dissolution rate. Parameters with constant values throughout the experiments were the leach solution pH, the nutrient medium composition, the dilution rate and the ore and sulfur grain sizes. It was found that the ferric ion concentration was the most significant factor and had a positive effect on the final percentage extraction of manganese from the ore and also on the rate of manganese solubilization from the ore. The effects of the other factors studied are discussed in detail.

Jan 1, 1997

By M. Rakoma

Following the blasting fatality on 17 December 2009, Landau Colliery was forced to change from the blasting practices that had been utilized since the start-up of the mine. Since then, attempts have been made to optimize blasting results. The challenge is rooted to the mining environment - during the early life of the mine, mining took place in virgin areas, whereas currently mining is taking place in areas overlying old underground bord and pillar workings. The underground bord and pillar workings aggravate phenomena such as spontaneous combustion, hot holes, and sinkholes. The 2009 fatality was attributed to hot holes causing premature detonation. Landau has been struggling with poor results from their overburden and coal blasts; leading to poor fragmentation of overburden and the PI parting that lies between the No.1 and No.2 coal seams. An extensive literature survey was completed in order to identify possible alternative solutions that could be evaluated for this unique mining environment, which demands a high degree of caution during mining to ensure factors such as dragline stability and personnel safety. The literature survey confirmed that the previous blasting technique, which was mainly characterized by air decking, was indeed the more efficient, although it was deemed unsafe because of the possibility of hot holes and the high sensitivity of detonators. Potential modifications to the blasting technique were modelled in a Microsoft Excel simulation that was available from the mine, and pit visits were conducted in order to determine whether implementation would be a problem. From the model it is evident that results can be improved by changing the current burden and spacing ratio. Visiting the pit revealed that the tie-in pattern and drilling inaccuracies are contributing to problem areas.

Jan 1, 2013

By Wagner Viana Bielefeldt, Felipe Buboltz Ferreira, Antônio Cezar Faria Vilela

The continuous casting machine is one of the most important steel production steps in a melt shop. The tundish, a reservoir between the steelmaking ladle and the mold, has great influence over the steel cleanliness, along with the productivity bid. It must takes into account the quality of the metal and operational safety. Several different variables are related to the tundish process, of inclusionary cleanliness. Some of them are discussed in this paper: the free opening of ladle, tundish inertization, steel temperature in the reservoir and clogging formation, besides a brief topic about castability. Therefore, a critical analysis, with a review from some papers available in literature, is proposed in this study, with its focus on tundish.

Oct 1, 2019

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By T. H. Adair

"IntroductionCONTINUOUS casting of ferrous and non-ferrous metals is not a new innovation. Patents describing machines for continuous casting are on file as far back as the year 1842. In the middle of the last century, Sir Henry Bessemer conceived and built a continuous casting• machine for the production of mild steel sheet.The production of billets and slabs of both non-ferrous and ferrous metals is being carried out by the continuous method on a fairly large scale on this continent and abroad. At present, the volume of production of •copper and aluminum and their alloys in billet and slab form is much greater than the continuous casting of steel products. The new installation of a continuous casting unit at Atlas Steels, Limited, is designed primarily for the casting of alloy steel billets and slabs.As an introduction to the art of continuous .casting of metals, it is interesting to examine a few of the many devices which have been developed. As previously mentioned, Sir Henry Bessemer constructed a machine for the direct casting of mild steel sheet. His discoveries and ideas of continuously casting steel formed the foundation for the work of other pioneers in this field, all of whom have contributed to the improvement of this art through the ensuing years. The machines which will be selected for examination are those of Bessemer, Poland-Lindner, Williams, Ennor, and Junghans. The last unit to be discussed will be a modification of the Junghans machine recently installed at Atlas Steels."

Jan 1, 1954

By Bong Sun You

AZ31 magnesium plate of 300mm in width and 40mm in thickness was produced by horizontal continuous casting machine, and its microstructures were analyzed on the surface and in the plate interior. The defect formation on the surface and subsurface, such as side cracks, buckling, pores and segregation, was very sensitive to the casting condition and processing parameters. Especially, casting speed and secondary cooling were the most dominant parameters to control the solidification behavior of magnesium melt, for example the position and shape of the solid/liquid interface in the mould. The cyclic marks on the surface were obvious because the plate were drawn by 4-step cycle and can not be removed. The average grain size of as cast plate measured as 50-65µm at the near surface and 300-400µm in the center of the plate was relatively small because secondary cooling water was applied to control the surface quality resulting in rapid solidification of the melt in the mould.

Jan 1, 2006

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981