Search Documents

By J. Chipman, N. J. Grant, R. Rocca

D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—With reference to eqs 7 and 8, at what temperature do they apply John Chipman (authors' reply)—That was 1600°C. Dr. Babcock—You have l x 10-4 as the component for the lime and 1 or 4x10-. Now, is it by dividing one into the other you get the 400? That is assuming equivalent activity on the part of oxygen, sulphur, and magnesia. Dr. Chipman—Yes, they are calculated for 1600. Now, the first one for CaO was calculated before we had a glimpse of Dr. Rosenqvist's paper." If you take his calculation you get 14,000 cal which is very good agreement, but our calculation would be superseded by Dr. Rosenqvist's new data. Dr. Babcock—The state you assume those to be in is the liquid state, as near as you can measure? Dr. Chipman—Naturally it is based on the solid CaS, but if you add the effect of fusion on both sides it just about balances out, so the ratio would be about the same. B. M. Larsen (U. S. Steel Co., Kearny, N. J.)—If we knew the activity of sulphur in the slag instead of merely the percentage, we might be able to find some conflicting factors that balance one another out, and find that the FeO or oxygen pressure effect is really present over the whole range. Dr. Chipman—I am fairly sure we would. The activity of sulphur in the slag and the activity of CaO in the slag, if we just knew those quantities, would enable us to save a lot of this computation and assumption and all the approximations we are doing now. Mr. Larsen—Two other points perhaps should be included: 1—an independent effect of manganese in helping the desulphurization; and 2—the number of mols of constituents or number of mols of ions or whatever there is in the slag could vary with these compositions in such a way that you get dilution effects. Dr. Chipman—You can figure all that in if you want to and it might improve the degree of approximation a little bit. Maybe enough to justify the labor of calculation, inaybe not, but we did not do it. L. S. Darken (U. S. Steel Co., Kearny, N. J.)—The authors have tackled a very complicated problem in trying to tie together in one picture the desulphurizing problem over the wide range of basicity and oxidation level from that of the open hearth to that of the blast furnace. At the present state of our knowledge of slags such an ambitious undertaking necessarily involves the adoption of numerous hypotheses. Their formulation (eq 11) for the higher FeO range

Jan 1, 1952

By Avnulf Muan, P. V. Riboud

The effect of Cr2O3 on melting relations of iron oxide at oxygen pressures slightly above those prevailing in contact with metallic iron has been determined. Liquidus and solidus temperatures of wüstite are raised by the addition of Cr2O3, from 1385°C for pure iron oxide to 1420°C at the peri-ledie point where wüstite, iron chromite, liquid, and gas coexist in equilibrium under the atmospheric conditions used in the present investigation (CO2/H2 = 1). It has been shown in a previous investigation1 that the liquidus and solidus temperatures of iron oxide are drastically increased by the addition of Cr2O3 under the relatively oxidizing conditions prevailing in air. This is to be expected in view of the easy substitution of cr3+ for Fe3+ in crystalline oxide structures which are stable at high oxygen pressures, as demonstrated for instance by the completeness of the solid solution series Fe2O3-Cr2O3 at high temperatures (>1000°C). The stable phase of iron oxide at oxygen pressures approximating those prevailing when metallic iron is present is wüstite. This phase, although commonly represented by the simplified formula FeO for sake of convenience, in reality has a defect structure in which a part of the iron ions are present as Fe3+. It is to be expected that at least a limited amount of cr3 ions will substitute for Fe in this structure when Cr2O3 is added to wüstite. Depending on the ease of this substitution in comparison with that of cr3 substitution for Fe in iron oxide-Cr2O3 liquids under the same atmos- pheric conditions, the liquidus and solidus temperatures of wüstite may increase or decrease upon addition of Cr2O3. The methods of establishing these melting relations and the results obtained are presented in the following. I) EXPERIMENTAL METHOD 1) General Procedure. The quenching technique was used in this study. Oxide mixtures were heated at chosen constant temperatures in an atmosphere consisting of equal parts of CO2 and H2 until equilibrium was established among gas and condensed phases. The samples were then quenched in mercury to room temperature, and the phases present were determined by microscopic and X-ray investigation. 2) Preparation of the Mixtures. Starting mixtures were prepared by weighing and thoroughly mixing Fe2O3 and Cr2O3, or wüstite and Cr2O3. The Fe2O3 and Cr2O3 used were "Baker Analyzed" reagent grades, whereas wüstite of composition was synthesized by reducing Fe203 at 1325°C in an atmosphere consisting of equal parts of CG andHz. In order to avoid contact with crucibles, the equilibration runs were made with small pellets suspended from thin (-0.004-in.) platinum wires. Mixtures made from FOs and Cr203 were readily pelletized at a pressure of 500 atm in a 9.5-mm die, whereas mixtures made from wüstite and Cr203 when treated identically were too weak for handling. In order to obtain a stronger product, these pellets were sintered by heating for 2 min at -1200°C in the same atmosphere as was subsequently used for the equilibration runs (CG/H2 = 1:1). During the sintering, these pellets were wrapped in thin (0.0004-in.) platinum foil, which was stripped off before the equilibration runs. In order to reduce the time needed for equilibrium to be attained, preliminary equilibration of relatively large pellets of each mixture was carried out at -1200°C for 4 to 12 hr. Smaller pellets

Jan 1, 1964

By J. P. Morris

PREVIOUS investigations1,2 have shown that alloying elements in liquid iron influence the thermodynamic activity of sulphur and thereby affect the partition of sulphur between metal and slag in the desulphurization process. For example, the greater efficiency of desulphurization in the blast furnace as compared to the open hearth can be attributed in part to a higher level of sulphur activity in blast-furnace metal due to the higher concentration of carbon and silicon. In the present investigation, a short study was made of the influence of manganese on the activity of sulphur in liquid iron and iron-carbon alloys. In contrast to carbon and silicon, manganese was found to decrease the activity coefficient of sulphur; and in iron-carbon alloys it counteracts to some extent the influence of carbon. However, at manganese concentrations normally present in the blast furnace or open hearth, the effect of manganese is small. Since manganese sulphide has a limited solubility in iron, manganese can act, under certain conditions as a desulphurizing agent. Considerable data on the manganese-sulphur product in carbon-saturated melts were obtained in the investigation and have been included in this report. The experimental procedure was the same as that used in the earlier investigations on the effect of silicon' and carbon' on sulphur activity. Briefly, the method was as follows: The molten alloy, contained in a graphite or sintered alumina crucible, was brought to equilibrium at a constant temperature with a mixture of hydrogen and hydrogen sulphide of constant composition by bubbling the gas through the metal. Samples of' the melt were taken for analysis at regular intervals by suction through a 2 to 3 mm bore silica tube dipped into the metal. The experiments were run in a graphite spiral resistance furnace with melts weighing 50 to 60 g. The gas bubbling tubes were made of sintered alumina and were 5/16 in. OD, 1/16 in. ID, and 24 in. long. Equilibrium was assumed to have been attained when the sulphur content of the liquid metal reached a constant value. During an experiment there was a rapid loss of manganese from the melt by volatilization. To offset this loss, small additions of manganese were made periodically. The rate of manganese addition needed to maintain a constant manganese concentration was determined in preliminary tests. In all of the experiments, deposits of manganese sulphide formed above the melts in a cooler region of the furnace. Apparently, these deposits resulted from a reaction between manganese vapor and hydrogen sulphide in the gas. To prove that manganese sulphide did not volatilize from the melts to a measurable extent, an experiment was run in which helium was bubbled through liquid iron containing both manganese and sulphur. Although manganese volatilized rapidly in this test, there was no appreciable loss of sulphur. Volatilization of manganese sulphide from a melt would have led to an apparent equilibrium condition in which the sulphur content of the metal was lower than the true equilibrium value. The experimental results are shown in the first seven columns of Table I. The data in the last two columns were obtained from the previous work on the effect of carbon' and show what the results would have been in the absence of manganese but with temperature, gas composition, and carbon content of the metal remaining the same. Comparison of the last four columns show that, in the presence of manganese, the sulphur content of the metal increased at equilibrium and the activity coefficient of sulphur decreased. However, the results show that, for manganese concentrations below 3 pct, the effect of manganese is small. The values for activity coefficient of sulphur given in Table I were calculated from the following relations: S (in liquid metal) + H2 (gas) = H2S (gas) [l] K ph2s/?s X %S X phg = 0.00251 [2] where K is the equilibrium constant for the reaction, PH2S and ph2 are the partial pressures of hydrogen sulphide and hydrogen, respectively, and ?s is the activity coefficient of sulphur. The standard state for sulphur was taken to be a 1 pct solution of sulphur in pure iron. The numerical value for K at 1600°C was determined in the earlier work. For the purpose of showing graphically the results of the tests run at 1600°C, the activity coefficients of sulphur were recalculated so as to correspond to a manganese concentration in the metal of 2 pct in each case. In the calculation it was assumed that the increase in sulphur content of the metal at equilibrium caused by the presence of manganese

Jan 1, 1953

By A. Simkovich, C. W. McCoy

THE relationship among chromium, carbon, and temperature during the oxidation period of stainless steel melting was developed by Hilty et a1 1-3 whose studies were confined to plain chromium stainless steels. The simplified version of their relation is given by the equation:

Jan 1, 1962

By R. H. Gautschi, F. C. Langenberg

Rare-earth additions were made to laboratory heats of Type 310 stainless to observe their effect on as-cast ingot structure, nitrogen and sulfur contents, and nonmetallic inclusions. Lanthanum had a grain-refining effect in 30-lb ingots, but results with 200-lb ingots were inconsistent. Cerium, lanthanum, and misch metal lowered the sulfur content when the sulfur exceeded 0.015 pct and the rare-earth addition was greater than 0.1 pct. The rare-eardh content in the metal dropped very rapidly within the first few minutes after the addition. The size, shape, and distribution of nonmetallic inclusions was not changed in 30-lb ingots, but changes were noticed in larger ingots. RARE-earth* additions have been made to austenitic Cr-Ni and Cr-Mn steels to improve their hot workability. The high alloy content of these steels often results in a considerable resistance to deformation and inherent hot shortness at rolling temperatures, particularly in larger ingots. Rare earths in the metallic, oxide, or halide form are usually added to the steel in the ladle after deoxidation although they can be added in the furnace prior to tap or in the molds during teeming. The literature- indicates that the effects of rare-earth treatments on these stainless steels are not consistent, and sometimes even contradictory. Since no mechanism has been presented which satisfactorily accounts for the claimed improvements, the effects of rare earths are a qualitative matter. The work described in this paper was initiated to expand the knowledge of the effects of rare-earth additions on melting variables such as ingot structure, chemical analysis, and nonmetallic inclusions. REVIEW OF LITERATURE Ingot Structure—Rare-earth additions to stainless steels have been reported to cause a change in primary ingot structure in that there are fewer coarse columnar grains. However, the results are inconsistent. While one investigation1 has shown a large reduction in coarse columnar crystals, another2 has been unable to observe this effect, particularly when small ingots were poured. Post and coworkers3 observed ingot structures for a number of years and found that the columnar type of structure is not definitely a cause of any particular trouble in rolling or hammering, provided the alloy is ductile. Knapp and Bolkcom4 found rare-earth additions to be quite effective in preventing grain coarsening in Type 310 stainless steel. Chemical Analysis—Many effects of rare-earth treatment on chemical analysis have been claimed in the literature. Russell5 observed that some sulfur is removed by rare-earth metals, and that a high initial sulfur content improved the efficiency of sulfur removal. Lillieqvist and Mickelson6 report that rare-earth treatment causes sulfur removal in basic open-hearth furnaces, but not in basic lined induction furnaces. Knapp and Bolkcom found no sulfur removal in acid open-hearth and acid electric furnaces, probably because the acid slag can not retain sul-fides. snellmann7 showed that sulfur could be lowered apprecfably with rare-earth additions; however, a sulfur reversion occurred with time. Langenberg and chipman8 studied the reaction CeS(s) = Ce(in Fe) + S(in Fe), and found the solubilit product [%Ce] [%S] equal to (1.5 + 0.5) X 10-3'at 1600°C. Results in 17 Cr-9 Ni stainless were about the same as those in iron. Beaver2 treated chromium-nickel steels with 0.3 pct misch metal and observed some reduction in the oxygen content. He also noted an inconsistent but beneficial effect of rare earths when tramp elements were present in amounts sufficient to cause difficulty in hot working. It is not known whether rare earths reduce the content of the tramp elements or change the form in which these elements appear in the final structure. No quantitative data are available concerning a possible effect of rare-earth treatment on hydrogen and nitrogen contents. However, Schwartzbart and sheehan9 stated that additions of rare earths had no effect on impact properties when the nitrogen content was low (0.006 pct), but served to counteract the adverse effects of high nitrogen content (0.030 pct) on these properties. Knapp and Bolkcom4 analyzed open-hearth heats in the treated and untreated conditions and found the nitrogen content (0.006 pct) to be unaffected. These two results lead to the speculation that rare-earth additions can reduce the nitrogen content to a certain level. Decker and coworkers10 have observed that small amounts of boron or zirconium, picked up from magnesia or zirconia crucibles, increased high-tem-

Jan 1, 1961

By W. O. Philbrook, K. M. Goldman, G. Derge

THIS is the third in a series of papers from the Metals Research Laboratory dealing with the transfer of sulphur across the iron-slag interface in a carbon-saturated system. The first paper' showed that the transfer obeyed first-order kinetics. The second' presented detailed evidence in support of the three-stage mechanism: FeS(Fe) FeS(slag) FeS(slag) + CaO(sing) ? CaS(slag) + FeO(slag) FeO(slag) + C ? Fe + CO. This emphasized the role of an iron-sulphur complex as the transfer agent across the interface and as an essential intermediate in the overall process. The present paper shows the influence on the process of the individual elements, carbon, silicon, manganese, and phosphorus, the alloying elements normally present and of interest in commercial blast furnace operations, aluminum, which has a pronounced accelerating influence, and nickel and copper, which are common minor impurities in the raw materials. The experimental methods and procedures for interpretation of data are the same as described earlier.1,2 Induction heated, graphite crucibles were used, and sulphur-free slag was added to the molten iron containing sulphur and the selected alloy. Slag samples were taken at regular time intervals and analyzed for sulphur and other components of interest. The authors wish to state specifically that these experiments were not intended to simulate industrial blast furnace operations. However, they do represent a study of the kinetics and mechanism of sulphur transfer at the slag-metal interface under specified laboratory control of the major variables in the system. It is believed that the results can be usefully applied to the blast furnace if consideration is given to the differences which are known to exist between the two conditions. A rigorous evaluation of the accuracy of rate studies is difficult. Recognized sources of error include sampling and analysis of both slag and metal, temperature measurement and control, selection of zero time, composition of the gaseous atmosphere over the reaction system, and extraneous sources of sulphur from the graphite crucible and reagent materials. In this study carefully standardized procedures were followed consistently in order to minimize the errors. It is believed that the reproducibil-ity of duplicate runs indicates that errors have been rendered negligible relative to the observed effects from intentional variables. For example, original experimental points for duplicate runs are shown in Figs. 1, 2, 7, etc. In most cases in this paper the drawn curves represent an average of at least two heats. The spread in sulphur values at a given time ranges from 0.02 to 0.08 pct, which is a small frac-tioi of the total values ranging up to 2 pct S in slag. In the systematic study of the influence of alloy additions, each element was added over a range of concentrations. The two slags used in this study were designated as "acid" or 1530 and "basic" or 1545. They had the nominal compositions given in Table I. Rates were measured in the temperature range 1500" to 1650°C. Data will now be presented to illustrate the various features of the study. Silicon The first alloying element examined was silicon, because its presence is unavoidable in any silicate slag system through the reaction y/2SiO2(slag) + xM?y/2Si(liq.Fe) + MxOy where M is any reducing agent such as iron or carbon. It is known that the attainment of equilibrium by this reaction is extremely slow and probably not reached in the blast furnace." The influence of silicon on the final stages of the sulphur reaction has also been studied.' It has been shown5 hat silicon increases the activity of sulphur in iron. For such reasons silicon may also be expected to influence the kinetics of the reaction. The observed effects will now be described. The general procedure was to melt 530 grams of ingot iron in a graphite crucible, 3 in. OD, 2 1/4 in.

Jan 1, 1955

By Nicholas J. Grant, Olaf Troili, John Chipman

D. C. Hilty (Union Carbide & Carbon Research Laboratories, Niagara Falls, N. Y.)—How does this effect of silica compare with the effect of silica in combining with the lime in the slag to reduce the activity of CaO, thereby affecting the first equation? John Chipman(authors' reply)-—That is the object of showing this effect for slags of two different basicities. In the more basic, the silica is more firmly tied up in the slag and is less easily reduced. It is therefore less able to interfere with desulphurization. The important point is that silica is acting in two ways. Of course it is an acid and as an acid it ties up lime and in tying

Jan 1, 1952

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers' determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By Nicholas J. Grant, Ulf Kalling, John Chipman

THE operation of a blast furnace is dependent to an important extent upon the sulphur content of materials charged and the desired limit of sulphur in the product. It has long been known that the blast furnace is the most efficient tool for desulphurization in common use and that this efficiency is associated with the strongly reducing conditions of the hearth and is enhanced by increased basicity and fluidity of the slag. The chemical reactions of desulphurization may be studied from the viewpoint of the ratio of the process or of the final equilibrium conditions. Both kinds of studies contribute to an understanding of the process and both are included here. A simple measure of the desulphurization power of a slag is given by the ratio: Pct sulphur in slag (Pet S) Pct sulphur in metal [Pct S] This ratio was used by Holbrook and Joseph',' to measure relative desulphurizing powers under controlled laboratory conditions. It was also used by Hatch and Chipman3 as a measure of the equilibrium distribution. For the latter purpose it would be preferable to employ thermodynamic activities rather than percentages, but until very recently this has been impossible for lack of data. Now, thanks to the work of Morris and Williams and Morris and Buehl," the effects of carbon and silicon upon the activity of sulphur in the metal are known. The confirmation of this work and its extension to include the effects of other elements by Sherman and Chipman and by Rosenqvist and Cox' make it possible to calculate the activity of sulphur in pig iron of any composition. Hence it is now possible to use data on the equilibrium distribution of sulphur to find its activity in the liquid slag and to approach an ultimate solution of the thermodynamic aspects of the problem. The rate of transfer of sulphur from metal to slag is the problem of major industrial importance and indeed the principal need for equilibrium data has been as a necessary adjunct to the kinetic studies. The rate of approach to equilibrium under laboratory conditions seems slow compared to the requirements of industrial practice, and it is clear that further laboratory studies of rates are needed. In the research reported below, the items which were investigated were the following: I—The role of mechanical stirring on the approach to equilibrium. 2—The role of MgO in desulphurization as compared to CaO. 3—The role of MnO in desulphurization. 4— The limiting reactions which constitute the slow steps in desulphurization. Experimental Procedure The experimental set-up and procedure previously described by Hatch and Chipman" were essentially followed with several small modifications. The graphite crucible containing the slag and metal charge was altered to provide considerably more active stirring and mixing of the slag and metal in the carbon monoxide atmosphere. For this purpose the crucible was machined to provide two deep cylindrical wells which were interconnected at top and bottom as shown in Fig. 1. A graphite screw with a flat thread and of shallow pitch (4 threads per in.) spinning at 600 to 800 rpm was used to lift the slag and metal over the partition between the two wells and throw them over into the second well, where the metal settled through the slag into the reservoir at the bottom. It was possible to see actual particles of slag and metal being thrown over the partition. In this respect, the stirring was more vigorous than used in the work of Hatch and Chipman. A charge of 400 g of wash metal was first melted, and 20 g of FeS was then added to yield a bath containing 1.65 pct S. Immediately 400 g of slag (as pure mixed oxides) was added and fused. The slag was generally fused in 1 hr * 10 min. Within 30 to 45 min after melting, the temperature was adjusted to 1525"C, and the first slag and metal samples were taken. The slag was picked up on the end of a cold Armco iron rod, whereas the metal was sucked into a silica tube. The wash metal composition was (in percent): 4.29 C; 0.022 S; 0.021 P; 0.38 Si. The slags used were of four fixed starting compositions covering a wide range of acid-base ratios shown in Table I. Deliberate variations in MgO were made in these slags to check the role of MgO in blast-furnace desulphurization. Changes due to additions and reactions were followed by analysis of samples. Additions of Mn and MnO were made to most of the heats to note the role of Mn and MnO on desulphurization. Three heats (62 through 64) were made in an open pot induction crucible (graphite) using a

Jan 1, 1952

By D. A. Dukelow, G. Derge

THE Fe0-Mn0-Si0, system has many properties of fundamental interest besides its occurrence in steel-making. The system is the simplest ternary complication of the FeO-SiO, binary whose electrochemical properties have been explored. Therefore, knowledge of the conformance of Fe0-MnO-SiO, melts to Faraday&apos;s laws, as investigated by current efficiency measurements, would be of particular value in interpreting the observed variations of electrical conductivity, while at the same time furthering understanding of this type of molten oxides. Pertinent to the present study are conductivity data of FeO-SiO, and Fe0-Mn0-SiO2, and current efficiency data of FeO-SiO,. Concerning conductivity measurements, Inouye, Tomlinson, and chipman&apos; studied the specific conductivity, a, of molten wüstite as a function of temperature and oxide addition. Liquid FeO in equilibrium with an iron crucible was found to have a o whose magnitude and positive temperature coefficient were undeniably semiconductor in nature (o1400°C = 269 ohm-1cm-&apos;). Additions at 1400°C of 5 mole pct MnO decreased o to 227 while a similar addition of SiO2, dropped o to 125. Additional SiO2 produced an exponential decline of o. It was reasoned that because wüstite is known to be oxygen excess and since there is no pronounced change in oFeO upon melting, that UFeO(L)is p-type semiconduction. Björling2 gives o data for the ternary FeO-MnO-SiO, using fayalite, 2 FeO-SiO,, as the base substance. Upon addition of tephroite, 2 MnO-SiO, he noted a small decrease in o. Taking his data for 1400°C with one-half of the fayalite replaced by tephroite, o shows a decrease of some 40 pct relative to o for fayalite, i.e., 5 ohm-&apos; cm-&apos; to 3. In line with this observation, Mori and Matsushita3 reported that substituting MnO for FeO in the silicate de- creased o slightly except at high SiO, contents where the decrease was somewhat larger. Investigating the ionic nature of FeO-SiO2 melts, Simnad, Derge, and George4, found the anode current efficiency, C,, as calculated from iron anode weight loss, was temperature invariant and in general increased with SiO2 concentration. The authors suggested the possible presence of electronic conduction to explain why C+ < 100 pct. Fig. 4 includes their results as curve (b). EXPERIMENTAL METHOD Apparatus—Fig. 1 is a schematic section of the electrolysis cell used in all the current efficiency runs. The melt was contained in an iron crucible that rested on an alundum ring. A centered silica tube came within 1 in. of the surface of the melt and initially served as a thermocouple well and then as the guide for the anode.

Jan 1, 1961

By R. Littlewood

The concepts of "redox potential" and "oxide-ion activity" are suggested as measures of the fundamental slag properties of interest to the extraction metallurgist. Thermodynamic data for single oxides are presented graphically in these terms and a method of expressing desulfurization of steel in electrochemical terms is indicated. The application of the theovy to mixtures of oxides (slags) is discussed and the redox potential is shown to provide a link between all the redox equilibria in a slag-metal system. In particular, the redox potential of the slag, its basicity, and the oxygen partial It is now generally recognized that slags are mixtures of polymeric anions of silicates, aluminates, phosphates, and so forth, neutralized by cations. However, conventional thermodynamic treatments of slags have almost always been in terms of activities of the pure component oxides (e.g., SiO,, CaO, A1203, and so forth), which are known not to exist as such in slags. While this type of empirical treatment is perfectly acceptable and provides a rigorous and self-consistent way of considering thermodynamic properties, it can give little guide to the structure of slags, since its very nature ig- pressure are closely connected. Direct deternzination of these by electrode-potential measurements is possible. Literature calculations of ion activities in the system Ca0 -Fe0-SiO,/molten iron are used to evaluate redox potentials, which are shown to correlate with data on sulfur partition in the system. In addition to its application to equilibrium conditions, an electrochenzical approach to slag-metal reactions might provide a basis for new methods of studying the kinetics of these reactions and for plant-control instruments in the pyrometallurgical industries. nores such complications. Recently, the thermodynamic properties of some slags have been successfully interpreted in terms of activities of anions of varying degrees of complexity. (While these have been successful curve-fitting exercises, there is no direct implication that the anions used in the models are necessarily the ones which actually exist in slags.) The success of these ionic thermodynamic treatments is encouraging but a complete picture of slag structure is still a long way off. What is needed is a complete knowledge of the values of stability constants for all reactions in slags of the type:

Jan 1, 1965

By W. J. Slatosky

As a means of effecting better control of endpoint temperatirres at the Jones & Laughlin basic oxygen furnace plant, a set of mathematical equations has been developed. The eqlutions are the product of a themlochemical anaysis of the process and aye designed to calculate the required scrap, lime, and hot metal additions in terms of a number of independent variables. Results of test heats have warranted adoption of this technique by the Prodrrction Department. BECAUSE of the autogeneous nature of the basic oxygen steel-making process, bath temperature can be controlled without an external fuel supply by charging the furnace with additions that are thermally balanced. The thermal requirements of the charge materials are such that, during the refining process, they throttle the heat generated by the metallurgical reactions in a manner designed to result in a speci-fied temperature at the completion of the heat. In the past, operating personnel at the basic oxygen furnace plant of Jones & Laughlin&apos;s Aliquippa Works relied on their experience and technical knowledge of the process to determine the quantities of charge additions needed to result in a finishing temperature in the range 2880"to 2920" F. (The charge consists primarily of 93 tons of scrap and hot metal plus an amount of lime sufficient to maintain a basicity ratio of 2.8 to 3.2). Estimates of these materials are based on a consideration of the effects on finishing temperature of 1) iron silicon content, having a variation of 0.8 to 1.8 pct; 2) iron temperature, ranging from 2250°to 2600°F; and 3)any excessive cooling of the furnace due to a production delay. The end temperature of the preceding heat also serves as a guide in that, if a heat was within the specified temperature range, the succeeding heat could be charged with materials of nearly the same proportions, provided the hot metal used in each of the two charges was of approximately the same temperature and composition. On the other hand, if a heat was outside the specified tapping range, or if the hot metal used in that heat was of different analysis and temperature from that of the iron to be charged, an adjustment in the proportion of additions is in order for the following heat. Due to the complex thermochemical behavior of the process and to the inexact and subjective nature of the described method of determining charge additions, consistently accurate temperature control was not to be expected. Therefore, those heats out- side the specified tapping range necessitated subsequent adjustments by either reblowing the cold heats for a suitable length of time so as to elevate the bath temperature to the desired level, or cooling hot heats with a proper amount of scrap. Because extra time is required to make these adjustments, production is delayed. In an attempt to devise a method for improving temperature control, an analysis of the thermochemistry of the process was undertaken. This, in turn, led to the development of a set of mathematical equations which enable the calculation of the quantities of scrap, lime, and hot metal needed to result in any specified tapping temperature range. The analysis was not intended to be a repetition of work done by others such as McMulkinl or ~hilbrook.&apos; It was meant to be an extension of their work so that charge additions could be calculated not in terms of silicon alone but, rather, as a function of all independent variables. This paper presents the derivation of these relationships, their effectiveness in controlling bath temperatures, and a method of utilizing them on an operational basis. The Heat Balance—The first step undertaken in the analysis of the problem was the enumeration of the pertinent variables. A list is presented in Table I where it is noticed that these quantities have been separated into the following three categories: important variables, variables considered as constants, and variables to be neglected. The breakdown was an arbitrary one designed to facilitate the analysis; otherwise, the mathematical treatment would have been exceedingly cumbersome and complex. Fortunately, experience has shown that these simplifying assumptions do not seriously impair the accuracy of the calculations. These variables along with the limiting assumptions listed in Table n were then used to write a heat balance of the process by applying the equation of continuity, Rate of Rate of Rate of Increase = Income - Outgo PI ] of Heat of Heat of Heat.

Jan 1, 1962

By Nev A. Gokcen

DISCREPANCIES and scattering in the equilibrium data on the reactions of hydrogen, and CO with dissolved oxygen in liquid iron are un- duly large. Available experimental results on the reduction of liquid ferrous oxide, i.e., wüs-tite, with hydrogen and CO are questionable, as pointed Out by Darken and Gurry&apos;l Direct determinations of the solubility of oxygen in liquid iron are subject to errors which cannot be easily reduced by further experimental refinements, and therefore an accurate but indirect method is highly desirable. The purpose of this investigation was, therefore, 1)

Jan 1, 1957

By Donald B. Evans, Robert D. Pehlke

The solubility of nilrogen in liquid binary alloys of iron with Litanium. zivconium, columbium, vanndiurn, and tantalum was measured for alloy composiLions up to the solalbility limils of lhe alloy nitrides. All five alloying agents were found to decrease markedly the activity coefficient of nitrogen in liquid ivon. The metal/nitvogen mole ralios in the alloy nitrides formed were generally .found to be slighlly greater than 1.0, but in no case greater than 1.5. From the experimental data, the standard free energies of fortmation of titanium and zir-conium nitrides have been calculated for the Lemperaluve range 1550° to 1750 C. The solublily Products for columbium, tantalum, and vanadium nitrides are also reported. A number of research investigations have examined the effect of refractory metals on the solubility of nitrogen in liquid iron. Although data on zirconium are not available, investigators are in agreement that titanium, vanadium, columbium, and tantalum markedly increase the solubility of nitrogen in liquid iron. This fact alone makes desirable the acquisition of thermodynamic data for these elements in liquid iron. Since refractory metals are known to be stable nitride formers, they have been suggested as steel denitrifying agents, and some of their nitrides have recently been considered as containment materials for liquid iron and iron alloys. Most available thermodynamic data for these metals relate to their dilute concentrations, but effective thermodynamic treatment of these applications requires data at concentrations near the solubility limit of the alloy nitride. Although some work has been done at relatively high alloy concentrations in liquid iron (particularly for vanadium 2,3 and titanium 2,4), the results have been somewhat contradictory. Disagreement may be partly attributed to the fact that the compositions of most refractory metal nitrides have been shown to be nonstoichiometric, and to vary 2,5-8 depending on the temperature and nitrogen gas pressure with which the solid nitride phase is in equilibrium. One purpose of this study consequently has been to determine the compositions of the refractory metal nitrides precipitated from a liquid iron solution. EXPERIMENTAL PROCEDURE Rao and Parlee2 and Evans and Pehlke 9 have discussed the technique for measuring the solubility product of an alloy nitride phase in liquid iron by finding the point of departure of the nitrogen solubility from Sieverts&apos; law. The method consists of measuring the solubility of nitrogen in a melt of iron containing a known concentration of a second metal as a function of the nitrogen gas pressure over the melt. In this study the second metal was one of the refractory metals titanium, zirconium, columbium, vanadium, or tantalum. When the nitrogen pressure at which the refractory nitride forms is reached, a deviation of the measured solubility of nitrogen in the melt from Sieverts&apos; law is observed in the form of a "pressure halt." The concentration of nitrogen in the melt associated with this breakpoint in the nitrogen-absorption curve is then used to calculate the nitride solubility. The Sieverts method was used to measure nitrogen solubility as a function of nitrogen pressure and temperature. The experimental equipment for this technique has been previously described in detail. 1,9 Charge materials used were vacuum-melted high-purity iron (Ferrovac-E) and the best commercial grades of the refractory metals obtainable (in all cases at least 99.8+ pct pure). Recrystallized alumina crucibles were used to hold all melts except those containing zirconium, for which zirconia crucibles were necessary. Temperatures were measured by a disappearing-filament type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diameter sight hole in the crucible lid. By means of a technique previously described, 9 in which the refractory-metal nitride was precipitated at one temperature then redis-solved by raising the temperature 50°C and precipitated again at a higher temperature, it was possible to obtain data over a temperature range of up to 200°C on a single melt. It was found that this technique could not be used with melts containing zir-

Jan 1, 1965

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,&apos; which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman&apos; and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.&apos; The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957

By E. W. Filer, L. S. Darker

ONE of the primary purposes of this investigation was to determine how far blast-furnace metal and slag depart from equilibrium, particularly with respect to sulphur distribution. In studying the equilibrium between blast-furnace metal and slag, there are two approaches that can be used. One method is to use synthetic slags, as was done by Hatch and Chipman;&apos; the other is to equilibrate the metal and slag from the blast furnace by remelting in the laboratory. In the set of experiments here reported, metal and slag tapped simultaneously from the same blast furnace were used for all the runs. The experiments were divided into two groups: 1—a time series at each of three different temperatures to determine the t.ime required for metal and slag to equilibrate in various respects under the experimental conditions of remelting, and 2—an addition series to determine the effect of additions to the slag on the equilibrium between the metal and slag. An atmosphere of carbon monoxide was used to simulate blastfurnace conditions. The furnace used for this investigation was a vertically mounted tubular Globar type with two concentric porcelain tubes inside the heating element. The control couple was located between the two porcelain tubes. The carbon monoxide atmosphere was introduced through a mercury seal at the bottom of the inner tube. On top, a glass head (with ground joint) provided access for samples and a long outlet tube prevented air from sucking back into the furnace. The charge used was iron 6 g, slag 5 g for the time series, or iron 9 g, slag 7 % g for the addition series. This slag-to-metal ratio of 0.83 approximates the average for blast-furnace practice, which commonly ranges from about 0.6 to 1.1. A crucible of AUC graphite containing the above charge was suspended by a molybdenum wire in the head and, after flush, was lowered to the center of the furnace as shown in Fig. 1. The cylindrical crucible was 2 in. long x % in. OD. The furnace was held within &3"C of the desired temperature for all the runs. The temperature was checked after the end of each run by flushing the inner tube with air and placing a platinum-platinum-10 pct rhodium thermocouple in the position previously occupied by the crucible; the temperature of the majority of the runs was much closer than the deviation specified above. The couple was checked against a standard couple which had been calibrated at the gold and palladium points, and against a Bureau of Standards couple. The carbon monoxide atmosphere was prepared by passing COz over granular graphite at about 1200°C. It was purified by bubbling through a 30 pct aqueous solution of potassium hydroxide and passing through ascarite and phosphorus pentoxide. The train and connections were all glass except for a few butt joints where rubber tubing was used for flexibility. The rate of gas flow was 25 to 40 cc per min. As atmospheric pressure prevailed in the furnace, the pressure of carbon monoxide was only slightly higher than the partial pressure thereof in the bosh and hearth zones of a blast furnace—by virtue of the elevated total pressure therein. Simultaneous samples of blast-furnace metal and slag were taken for these remelting experiments. The composition of each is given in the first line of Table I. There is considerable uncertainty as to the significant temperature in a blast furnace at which to compare experimental results. This uncertainty arises not only from lack of temperature measurements in the furnace, but also from lack of knowledge of the zone where the slag-metal reactions occur. (Do they occur principally at the slag-metal interface in the crucible, or as the metal is descending through the slag, or even higher as slag and metal are splashing over the coke?) The known temperatures are those of the metal at cast, which averages about 2600°F, and of the cast or flush slag, which is usually about 100°F hotter. To bridge this uncertainty, remelting temperatures were chosen as 1400°, 1500" (2732°F), and 1600°C. For the time series the duration of remelt was 1, 2, 4, 8, 17, or 66 hr; crucible and contents were quenched in brine. The addition series were quenched by rapidly transferring the crucible and contents from the furnace to a close-fitting copper "mold." Of incidental interest here is the fact that the slag wet the crucible

Jan 1, 1953

By R. L. Hadley, G. Derge

The amounts of oxygen in liquid iron-titanium alloys up to 50 pct Ti were measured and the oxide phases in equilibrium with these alloys were determined by using TiO² crucibles. A minimum of about 0.003 pct 0 occurs at less than 1 pct Ti. The various liquid and solid oxide phases can be arranged on a ternary isotherm. THREE characteristics of titanium contribute to the interesting aspects of its reaction with oxygen in liquid iron: 1—It forms a number of stable oxides. 2—All oxides have large negative free energies of formation. 3—The pure metal exhibits high solubility for oxygen. In addition, the use of titanium as a stabilizing and strengthening element in alloys suggests a need for investigation of its reactions in amounts greater than those normally required for deoxidation. These higher compositions are also of interest because they occur during the addition of ferroalloys and produce deoxidation products before dilution is achieved. Titanium Deoxidation in the Literature While the use of titanium as an alloying element and deoxidizer has been common for several decades, the first detailed study of its deoxidizing characteristics was carried out by Wentrup and Hieber&apos; in 1939. These authors determined the extent of deoxidation possible with titanium and identified, by microscopic examination, the products formed. They found that titanium in excess of 0.2 pct did not reduce the oxygen content of iron below 0.004 pct at 1600°C. They identified the spinel FeO-TiO² at low titanium concentrations and Ti2O³ in melts containing more than 0.2 pct Ti. A portion of the area surveyed by Wentrup and Hieber has been investigated recently by Evans and Sloman² using X-ray diffraction for inclusion identification. They concurred in general with the findings of Wentrup and Hieber, but reported the existence of Ti³O5 as a deoxidation product in the range near 0.1 pct Ti. Comstock, Urban, and Cohen³ discussed the deoxidation of iron with titanium, correlating the data of Wentrup and Hieber with free-energy data for the titanium oxides. Scatter at high titanium values was considered attributable either to the formation of an oxide exhibiting high solubility in liquid iron or to the entrainment of solid oxide particles leading to high apparent solubility. Chipman&apos; has calculated the deoxidation curves for titanium based on free-energy data for titanium oxides. These calculations (Fig. 1) and those of Comstock, Urban, and Cohen involve assumptions as to the activity coefficients of oxygen and titanium in liquid iron, since such data have not been determined. Investigation of the deoxidizing characteristics of chromium" and vanadium0 have shown that these elements decrease the activity coefficient of oxygen in liquid iron, leading to a tendency toward relatively high oxygen values and experimental scatter in highly alloyed melts. Experimental This investigation involved two major objectives: 1—determination of the composition of the oxide phases in equilibrium with liquid Fe-Ti alloys, and 2—establishing the pattern of oxygen solubility in liquid Fe-Ti alloys at titanium concentrations in excess of that required for attainment of minimum oxygen content. Raw Materials Ingot iron was used having the following composition: 0.02 pct C, 0.017 pct Mn, 0.01 pct Si, 0.02 pct S, 0.006 pct P, and 0.03 pct 0. The titanium used

Jan 1, 1956

By S. Ramachandran, R. A. Walsh

Many investigations have shown that the manganese enhances the deoxidation power of silicon. Here it is suggested that this phenomenon could be explained in terms of the formation of impure silica. Data of Hilty and Crafts on the Fe-Mn-Si-O System has been evaluated on the basis of the reaction S_i + 20 = (SiO2) where (SiO2) denotes silica of variable activity. The activity of silica in this system is a function of aMn/aSi and the temperature, and can be described by the equation 12700 l°gaSiOz = -6.85+ - - 0.5 log aMn /asi PRACTICAL melting experience has shown that it is helpful to maintain a certain range of Mn/Si ratio in deoxidizing quality alloy steels. Herty,1 as early as 1932, reported a strong association between manganese and silicon as did schenck2 and Korber and Oelsen3 in later work. More recently, Hilty and crafts4 have studied the solubility of oxygen in the Fe-Si-O system, both with and without manganese. Their study confirmed the marked ability of manganese to increase the deoxidizing power of silicon. This phenomenon has remained unexplained in the liter,ature5 since it has been shown that manganese has virtually no influence on the activity coefficients of silicon or oxygen.= In this paper, an explanation for the role of manganese is suggested and equations are devised for quantitatively describing this influence. DISCUSSION Hilty and crafts4 equilibrated their melts under an argon atmosphere and the system established equilibrium with a self-generated slag which was not always the oxide of lowest free energy. Drawing on the early work of Korber and Oelsen,3 it was reasoned that the formation of complex Fe-Mn-silicates

Jan 1, 1963

By J. Chipman, M. N. Dastur

The importance of dissolved oxygen as a principal reagent in the refining of liquid steel and the necessity for its removal in the finishing of many grades have stimulated numerous studies of its chemical behavior in the steel bath. From the thermodynaniic viewpoint the essential data are those which determine the free energy of oxygen in solution as a function of temperature and composition of the molten metal. A number of experimental studies have been reported in recent years from which the free energy of oxygen in iron-oxygen melts can be obtained with a fair degree of accuracy for temperatures not too far from the melting point. Certain discrepancies remain, however, which imply considerable uncertainty at higher temperatures; also several sources of error were recognized in the earlier studies. It has been the object of the experimental work reported in this paper to reexamine these sources of uncertainty and to redetermine the equilibrium condition in the reaction of hydrogen with oxygen dissolved in liquid iron. The reaction and its equilibrium constant are: H2 (g) + Q = H2O (g); K1 _ PH2O / [1] Ph2 X % O Here the underlined symbol Q designates oxygen dissolved in liquid iron. The activity of this dissolved oxygen is known to be directly proportional to its concentrationl,2 and is taken as equal to its weight percent. The closely related reaction of dissolved oxygen with carbon monoxide has also been investigated:3,4,5 co (g) +O = CO?(g); K _ Pco2___ [2] K2= pco X % O [2] The two reactions are related through the wat,er-gas equilibriuni: H2 (g) + CO2 (g) = CO (g) + H2O (g); K2 = PCO X PH2O [3] PH2 X PCO2 and with the aid of the accurately known equilibrium constant of this reaction, it has been shown5 that the experimental data on reactions [1] and 121 are in fairly good, though not exact, agreement. Experimental Method Great care was taken to avoid the principal sources of error of previous studies, namely, gaseous thermal diffusion and temperature measurement. The apparatus was designed to provide controlled preheating of the inlet gases and to permit the addition of an inert gas (argon) in controlled amounts, two measures found to be essential for elimination of thermal diffusion. A known mixture of water vapor and hydrogen was obtained by saturating purified hydrogen with water vapor at controlled temperature. This mixture, with the addition of purified argon, was passed over the surface of a small melt (approximately 70 g) of electrolytic iron in a closed induction furnace. After sufficient time at constant temperature for attainment of equilibrium the melt was cooled and analyzed for oxygen. GAS SYSTEM A schematic diagram of the apparatus is shown in Fig 1. Commercial hydrogen is led through the safety trap T and the flowmeter F. The catalytic chamber C, held at 450°C, was used to convert any oxygen into water-vapor. A by-pass B with stopcocks was provided so that the hydrogen could be introduced directly from the tank to the furnace when desired. From the catalytic chamber the gas passed through a water bath W, kept at the desired temperature by an auxiliary heating unit, so that the gas was burdened with approximately the proper amount of water vapor before it was introdvced into the saturator S. All connections beyond the catalytic chamber were of all-glass construction. Those connections beyond the water bath were heated to above 80°C to prevent the condensation of water vapor. After the saturator, purified argon was led into the steam-hydrogen line at J, and finally the ternary mixture was introduced into the furnace. THE SATURATOR The saturator unit comprised three glass chambers, as shown in Fig 1, the first two chambers packed with glass beads and partially filed with water and the third empty. Each tower had a glass tube with a stopper attached for the purpose of adjusting the amount of water in it. The unit was immersed in a large oil bath, which was automatically controlled with the help of a thermostat relay to constant temperature, ± 0.05ºC, using thermometers which had been calibrated against a standard platinum resistance thermometer. The performance of the saturator over the range of experimental conditions was checked by weighing the water absorbed from a measured volume of hydrogen; the observed ratio was always within 0.5 pct of theoretical.

Jan 1, 1950

By J. F. Martin, L. M. Melnick, R. Rapp, R. C. Takacs

Recent studies on the determination of hydrogen in steel have shown that the hot-extraction method for removing hydrogen from a solid sample is preferable to its removal from a molten sample by vacuum fusion or by fusion in vacuum with tin. A number of techniques are available, however, for determining the hydrogen so extracted. They include: thermal conductivity, gas chromatography, pressure measurement before and after catalytic oxidation of the hydrogen to water and removal of the water, and pressure measurement before and after diffusion of the hydrogen through a palladium membrane. These techniques have been evaluated on the basis of initial cost, maintenance, speed and accuracy of analysis, and applicable concentration range. The results of this study showed that the palladium-membrane technique is best suited for routine use. FOR some time investigators have been concerned with the origin, form, and effect of hydrogen in steel. In such stdies&apos;, the analysis for hydrogen constitutes one of the most important phases. It is quite apparent that the results for hydrogen concentrations in a given steel are dependent on the method of obtaining the sample, storage of the sample until analysis, preparation of the sample, and analysis of the sample, including all the facets inherent in the calibration and operation of an apparatus for gas analysis. There are a number of means available for determining hydrogen. This is a critical study of some of the more common techniques in use today. In most conventional melting and casting methods, hydrogen concentrations of 4 to 6 parts per million (ppm) in steel are quite common. Because of the undesirable effects of hydrogen on steel there has been increased use of techniques such as vacuum melting,&apos; vacuum casting, and ladle-to-ladle stream degassing, which lower the hydrogen content to levels on the order of 1 to 2 ppm. Therefore, the method used for determining hydrogen in steel must be sensitive and precise. In any analytical procedure for gases in metals there are two distinct operations—the extraction of the gas from the metal and the analysis of the extracted gas. To extract the gas from the steel, three methods have been employed: 1) fusion of the sample with graphite at high temperature; 2) fusion with a flux, such as tin, at a lower temperature; and 3) extraction of the hydrogen from the solid sample at a temperature below the melting point of the steel. Fusion with graphite is the least-acceptable method. The blank in this method is higher and more variable than in either of the other two methods. The hydrogen fraction of the total gas composition usually is between 10 and 50 pct; thus, a larger analytical error is possible. The vacuum-tin fusion4 extraction of hydrogen is probably the most rapid method in use today; the extraction time is usually about 10 min. However, with this system a bake-out of the freshly charged tin for 2 hr is necessary and a change of crucible and a charge of fresh tin are required after each day of operation whether one or thirty samples have been analyzed. In addition, frequent checks of blank rates are required since CO and Na are continually being given up by the steel samples dissolved in the tin bath. The composition of the gas in this method lends itself readily to analysis; although the hydroge concentration may fall to as low as 50 pct, more often it is above 90 pct, thus allowing a more precise analysis (because of less interference from other gases). In 1940 ewell&apos; published the hot-extraction method for extracting hydrogen from the solid sample, comparing analysis for hydrogen extracted at 600°C with similar analysis for the gas extracted at 1700°C by fusion with graphite. Good agreement for hydrogen was obtained between these two methods, provided sufficient time was allowed for extraction at the lower temperature. carsone obtained good results in his comparison of this hot-extraction method with vacuum-tin fusion. Subsequent work by Geller and sun7 and Hill and ohnson&apos; has shown that steel samples should be heated to at least 800°C to effect the release not only of the diffusible hydrogen but also of the "residual" hydrogen that may be present as methane. Since the rate of evolution of hydrogene9l0 depends on such factors as sample size and composition, thermal history, and extent of cold work, a fixed extraction time is not possible. Extraction times of 30 min are normal, but 2 hr are not unusual. Induction or resistance heating may be used in the hot-extraction method. With resistance heating the

Jan 1, 1964