Search Documents

By Friedrich Benthaus

"The natural and man-made realities on either side of the Atlantic are different. Therefore, a large part of the other side' s knowledge and experience cannot be transferred easily. In the following, the author will attempt to describe some of those developments in the German hard coal industry which may be of particular interest to readers on this side of the Atlantic.The area of the Federal Republic is quite small, especially if compared with a country as large as Canada. On a territory the size of the maritime provinces of New Brunswick and Nova Scotia, Germany holds coal reserves roughly corresponding to the total Canadian reserves. More than 20 billion tons of hard coal down to a depth of 1500 m, and more than 30 billion ton s of brown coal of lignite are technically and economically extractable acording to current technology.However, not only are Germany's coal resources more concentrated; the country is also densely populated, and there are dense networks of railroads and highways All components of the so-called infra-structure are available everywhere, be it electricity, any machinery or personnel. Public opinion is likely in favour of an increased utilization of coal.The coal industry is well developed through a long evolution covering centuries. As a consequence, there is an effective and intensive cooperation of numerous bodies and institutions concerned with coal mining, from government agencies including the inspectorate to suppliers, trade union s, producing companies, to jointly operated management and research organizations. In the Federal Republic, hard coal is mined in deep mines only, and lignite in general, only from open-cast pits. There is a complete organizational and geographic separation of hard and brown coal in Germany. Because the Federal Republic holds only insignificant mineral oil and very little natural gas deposits, coal is essentially the only and consequently the most valuable source of energy."

Jan 1, 1984

By P. Somasundarrtn, A. Sivakumar

Flotation of minerals is governed by many processes at the solid/liquid/gas interface, such as adsorption and precipitation of surfactants. In this paper, the basic principles governing these processes and hence flotation are discussed. Also, recent techniques such as fluorescence and ESR spectroscopy which have been used to study in situ surfactant adsorption and to obtain information on the structure of adsorbed layer are discussed.

Jan 1, 1987

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By Jessica Smith

Jan 1, 2009

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By Andrew Palangio, Blessing Taiwo

Understanding rock mass structural features is essential for optimizing blast design, highwall control, and evaluating post-blast performance in both surface and underground mining operations. This paper presents a comprehensive methodology utilizing image-based structural mapping to accurately characterize geological discontinuities including joints, faults, and lineations captured from both terrestrial and aerial imagery at varying scales. Key structural parameters such as joint orientation, spacing, and apparent in-situ block size are extracted to understand rock mass classification and enhance blast design inputs with greater geotechnical precision. The study introduces a significant enhancement to the existing discontinuity assessment algorithm by integrating a deep learning-assisted detection process. This improvement enables more accurate, quantitative and consistent identification of pre-existing cracks and surface features across complex bench free faces. The enhanced system facilitates better evaluation of how structural features influence blast fragmentation, energy distribution, and slope stability. A case study from a limestone quarry illustrates the use of a derived comminution factor based on the relationship between joint-controlled pre-blast block sizes and post-blast fragmentation to evaluate blast performance and optimize future design strategies. The results highlight the value of structural analysis in reducing overbreak, minimizing underbreak, and improving fragmentation predictability. This paper emphasizes the importance of integrating structural assessments into the blasting workflow to enable a more data-driven, geotechnically informed, and performance-optimized approach to modern blast design and evaluation.

Jan 26, 2026

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005

By R Burgess-Limerick, D Lynas

A number of standards and guidance materials currently exist to assist equipment designers. The ISO process, however, is a formal process and change often lags behind technology development. In some cases, this may result in weak or ineffective standards that need to be written in general terms to accommodate future technology developments, meaning some standards may only establish minimum requirements and not be overly helpful to equipment designers, in particular when designing for workforce diversity and inclusivity. By contrast, advisory information as issued by various mining regulatory bodies is able to respond more quickly to changes in technology. Standards do however have a safety and productivity focus providing design consistency between equipment manufacturers, a basis for auditing purposes, assistance in mining regulation and compliance, and in the development and application of safety management systems. As an example of challenges facing equipment designers, ISO3411 (2020) provides data approximating the 5th, 50th and 95th percentile of the ‘earth-moving machinery operator population’ for numerous static dimensions relevant to the design of earth-moving equipment. These data are then utilised in ISO6682 (2020) to provide recommendations regarding the location of controls. Attempting to utilise the data provided in ISO3411 (or other sources of static anthropometric data) creates further challenges for equipment designers, in that reference percentiles is problematic for design purposes. There is no ‘5th or 95th percentile operator’ as individuals vary along each dimension (Robinette and Hudson, 2006). Although dimensions have some degrees of correlation, when multiple dimensions are considered, the range of individuals which fall within a given range on all dimensions reduces substantially. For example, only about 82 per cent of individuals in a population will fall within the 5th to 95th percentile ranges for both height and weight. The more dimensions are considered, the smaller the range of people who actually ‘fit’ the description.

Apr 16, 2024

By Scott Rosenthal

?EMESRT History ?Design Philosophies (DP?s) ?Industry Successes ?Participation Thinking Differently Earth Moving Equipment Safety Round Table ? Use a critical mass to influence Marketing ? Define ?Problems?not ?Solutions? ? Leave the OEM designers to develop solutions Work within the companies to improve purchasing

May 1, 2010

By K Johnson, G Morrison, N Lisowiec

The Mount Wright gold deposit is located near the town of Ravenswood, ~90 km south of Townsville, in north Queensland. The deposit has been mined by underground methods since 2006. It produced approximately 138 koz Au in the 2011 - 2012 financial year and has a total endowment of approximately 1 Moz Au. To facilitate near mine exploration, a re-logging campaign of 600+ diamond and RC drill holes was recently conducted, resulting in a revised three-dimensional (3D) geological model and improved understanding of the ore controls and the mineralised system. The deposit is within a Permo-Carboniferous breccia complex approximately 350 m diameter and more than 1200 m deep. It consists of early peripheral granite-rich breccia, polymict breccia, a rhyolite spine and a late tuffisite (fine-grained milled breccia) pipe. The rhyolite spine is approximately 60 m + 250 m + at least 1200 m deep and is zoned with massive, flow-banded and breccia phases that are in part gradational with the other breccias. There is extensive sericitic alteration centred on the tuffisite and rhyolite units and fading out into the shallower and peripheral polymict and granite-rich breccias. There is also a broad pattern of metal zoning with elevated Pb-Zn ¦ Ag in the upper 400 m, Au-Cu-Bi below 400 m fading out below ~850 m, and a poorly defined deep Mo-W-Te-Sb anomaly. The majority of the Au ore is between 400 and 850 m below the surface in the rhyolite spine. Below this, Au mineralisation is less coherent, and more localised in the margins of the rhyolite and in the adjacent tuffisite. The developing model is that the ore is not confined to or necessarily directly genetically related to the rhyolite spine, but is driven by other phases of intrusion that also generated the tuffisite pipe. This model is being used to generate additional drill targets away from the present mine development.CITATION:Johnson, K, Morrison, G and Lisowiec, N, 2013. Advancing near-mine exploration with an updated geological model for the Mount Wright gold deposit, Queensland, in Proceedings World Gold 2013 , pp 469-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Hossein Ghaedi, Hadi Fattahi

Despite the significant role of coal in the economic progress of nations, the occupational and health risks associated with its mining pose a major concern for industry stakeholders. The occurrence of roof collapses in coal mines remains a critical factor leading to substantial loss of life and financial damages for miners. Therefore, accurately predicting the roof fall rate (RFR) holds paramount importance. However, the uncertainty surrounding rock parameters in mines hinders the application of conventional methods to assess roof collapse rates in coal mines. To tackle the challenges associated with predicting roof fall rates in underground coal mines, this study proposes a novel solution by leveraging the Rock Engineering System (RES) method. The investigation is grounded in a dataset comprising 109 data points, encompassing crucial input parameters like depth of cover (DOF), primary roof support (PRSUP), intersection diagonal span (IS), mining height (MH), and coal mine roof rating (CMRR). In the model construction phase, 80% of the data (87 points) were utilized to build the RES model. A critical aspect of this study involves the evaluation of the RES model’s performance against alternative regression techniques, namely linear, power, exponential, polynomial, and logarithmic regression. This comparison was executed using the remaining 24 data points (20% of the dataset) for rigorous evaluation. Employing key statistical metrics such as mean square error (MSE), root mean square error (RMSE), and squared correlation coefficient (R2), the study systematically demonstrated the superior accuracy of the RES-based method compared to other approaches. In conclusion, the outcomes strongly support the efficacy of the RES method in predicting roof fall rates, not only in the specific case studied but also indicating promise for its application in other underground coal projects. This underscores the potential of the RES method as a reliable and versatile tool for forecasting roof fall rates in the complex and critical context of underground coal mining.

Mar 19, 2024

By D. Richardson

Presentation Objectives ?Demonstrate the utility of 3D modelling for visualizing exploration data ?Demonstrate the target generation ability of 3D model query methods Exploration Criteria -Example Given the Geology of Sudbury What Are Our Exploration Criteria? (selected examples) ?Geometry ?Trends ?Lithology ?Proximity to Sulphides ?Length and Grade of Anomalous Mineralization ?Distance from Footwall In Addition ?Geophysical Criteria ?Economic Criteria ?Amount of Available Space ? Depth

May 1, 2006

By A Karrech, G M. Hassan, A Varghese, E Lessing, S Martins

Pumps play a critical role in mining operations, and their energy consumption and environmental impact are significant. This paper addresses the need for a holistic approach to sustainable pump deployment by expanding on previous work presented at IMPC Asia Pacific 2022 and World Mining Congress 2023. The research takes a significant step forward by outlining a structured approach to estimate and demonstrate sustainability tailored for operational slurry pumps. It details the calculation methodologies used to quantify the carbon dioxide emissions from electricity, wear materials and transport, as well as sealing water usage. To enhance practicality and usability, a simplified visual representation—called sustainability metrics—has been developed to monitor overall efficiency. The sustainability metrics consist of the availability, pump efficiency, and water utilisation efficiency. The proposed methodology is integrated with Pumps Condition Monitoring Service to maximise benefits. Three case studies, from iron ore, copper, and nickel operations globally, were employed to evaluate the proposed methodology. The findings demonstrate the critical role of sustainability calculations in understanding pumps operation. These calculations improve awareness of the pump’s role in the sustainability journey and enable effective monitoring. The studies highlight that continuous monitoring paired with effective prescriptive maintenance strategy can significantly reduce power and water consumption while maximising pump availability. The case studies also reveal significant shortcomings in current operational practices and non-optimal maintenance regimes, emphasising the need for practical recommendations to maximise savings and optimise pump performance. In the context of increasing climate change awareness and the imperative for global decarbonisation, this research highlights the necessity of critically assessing methods and operations to drive sustainability in the mining industry. By adopting a holistic approach to sustainable pump deployment, mining operations can effectively reduce their environmental impact while enhancing operational efficiency and economic viability. The proposed methodology and case studies provide valuable insights and practical recommendations for mining companies seeking to achieve sustainable practices and contribute to a decarbonised future.

Sep 1, 2024

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

By Andrew I. Hustrulid

The Internet and World Wide Web create multiple opportunities to advance and change an industry. Scandura Conveyor Belting, a mid-sized manufacturing company supplying the mining industry, has embraced several of these opportunities that add value to the sale and service of the manufactured product. This paper presents a technical overview of available technology and how it is being applied to advance the conveyor belt industry. These technologies are used to provide historic catalog information, interactive troubleshooting, product installation and service instructions, detailed product information, technical calculations for the proper conveyor belt selection, and on-line site surveys and maintenance logs.

Jan 1, 2002

By Kevin Ross

Feasibility Study Team Processing / Engineering?Hatch, Vancouver Mining / Reserves?Australian Mine Consultants, Brisbane Geology / Resources?Roscoe Postle Associates, Vancouver Environmental / Permitting?Rescan, Vancouver Tailings BGC, Kamloops Probable Mine Components Mining tending towards caving methods Underground mine accessed by shaft /conveyor & decline Processing plant producing copper concentrate containing gold Concentrate trucked to rail head for export Non saturated tailings disposal

May 1, 2006

By James Quigley

As the outcrop mines in the West developed into underground operations, systems of ground sup- port were gradually evolved. In the early coal mines there was little need for support except near the dirt line in portals, where stone masonry was common. Where the top was shaley or broken, native pine props with light cross bars and legs furnished enough support even in Utah's 25-ft coal seams. As depth of workings increased, roofs and backs of the same general nature as those near the surface became more and more unstable and required more and more support. Some coal airways show this tendency very clearly. From the surface down the same type of roof shows deterioration which an experienced eye can translate into a measure of depth under surface rather than change in rock characteristics. Rock bolts, developed by various companies and by the U. S. Bureau of Mines, have become an effective substitute for timber in sections of some metal and nonmetal mines formerly requiring excessive timber support, and further use of war surplus landing mats, chain link fencing, and a new punched channel developed by one of the steel companies has enabled other mines to operate deposits where costs of timber and lack of clearance for timber support would have prohibited mining. The block caving mines have made extensive use of reinforced concrete underground to achieve similar ends under difficult conditions. Steel sets are standard in many Bureau of Reclamation projects, although these are usually covered in with concrete to make the permanent structures the Bureau's reclamation projects require. But the use of steel in mining operations is limited and has been confined principally to the iron ore mines of Michigan, Wisconsin, and Minnesota. Some mines have installed used rail as posts, caps, and crossbars, but a rail section is not suited for load carrying, and used rails are generally brittle, having a tendency to fail without warning when overloaded.

Jan 7, 1959

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By B. B. Gottsberger

HAVE given considerable thought during the past year to the subject of licensing of engineers and par-ticularly to the position which the mining engineer should take on this question. I have found, however, that it is not a subject which yields much result for the thought expended on it. So far as any published record will show, mining engineers have been either ignorant of the extent to which the movement for the licensing of engineers has progressed or else indifferent to it. It is true that the Mining and Metallurgical Society of America, by a questionnaire sent out to its member-ship, did a great deal in calling this matter to the atten-tion of the mining profession, and so far as I know, the report of its committee, which analyzed the replies received, is the only published statement of the feelings and opinions of our branch of the engineering profes-sion. It is to be hoped that the conclusions shown by that report, namely, that mining engineers are almost unanimously opposed to the principle of licensing and consequently any legislation dealing with it, has received serious thought and that we are ready for an even more thorough consideration of the subject.

Jan 3, 1922