Search Documents

By F. Weinberg

Measurements have been made of solute segregation during dendrilic growth by using radioactive solute elements and ,measuring the activity of den(12-ites cut from decanted specimens. This has been done for both lead awl tin based binary alloys contaitzing the following solute additions: Ag, T1204, was dependet on ko, the equilibrium distribution coefficient in the following way Fay k &apos;c 0.1, C/C 0.6; for k0 >0.1. 0.6 <c,/c,< I. Qualitative obse?-vations were madc of dendritic segregation, by using autoradiographic techniques, for the Sn + Ag110 and Sn + Tlo4 systems. The observation were found to he in general agreement with the measurements ofCA/Co. Autoradiographic were also obtained of scctiolccl delzr11-iie stalks. These indicated that the stalks had a substructure, dclileated by solute corzetlt?atio?zs nlolg the substructure walls. A new dendrite growth direction <JI2> is reported for tila. SOLUTE segregation in dilute binary alloys has been investigated by Pfann,&apos; Smith, Tiller, and Rut-ter,&apos; and others. They considered the case of a slowly advancing plane solid interface, and derived expressions for the distribution of solute in both solid and liquid during solidification. To determine these expressions, they assumed no diffusion in the solid and either complete mixing in the liquid:&apos; or diffusion controlled solute movements in the liquid without any convective mixing.&apos; The present investigation considers solute segregation during dendritic growth, in which case the solid-liquid interface is not plane, and the growth rates are rapid. Segregation under these growth conditions has not been treated mathematically, because of the relative complexity of the system. It has been suggested by Chalmer, on the basis of preliminary results, that an alternative to the diffusion and heat flow controlled conditions during growth is &apos;diffusionless" dendritic growth in which solid is formed with the same composition as the liquid. He suggests this type of growth may depend upon a solvent-solute relationship that permits some solid solubility without excessive increase in internal energy, as is the case for solutions of tin in lead. On the other hand, Montariol,4 and others, have shown experimentally that some segregation does occur during dendritic growth in metals using etching and radioactive tracer techniques to indicate the concentrations of the solute. The present investigation was undertaken to determine, both qualitatively and quantitatively, the extent of solute segregation associated with dendritic growth in a series of binary alloys, as a function of solute concentration. PROCEDURE The solvent materials used were Vulcan Electrolytic tin (99.997 pct purity) and Tadanac lead (99.998 pct purity). The solute materials were Zn, Sn, and Sb (better than 99.998 pct purity), Ag and Co (99.5 pct purity), and T1 (Fisher "purified" metal sticks). Activation of the solute metals was carried out in the reactor at Chalk River, Canada. Master alloys were prepared by induction heating from the radioactive solute metal and the pure solvent, under argon, in graphite crucibles. Pieces of these alloys were then added to the solvent to give the required solute concentration. Dendrites were grown in essentially the same manner as that described by Weinberg and Chalmer, , in which controlled orientation single crystals were grown dendritically in horizontal graphite boats, and the liquid decanted. The crystals were grown and decanted in an atmosphere of tank argon. Before decanting, a sample of the liquid was drawn up in a glass tube and allowed to solidify rapidly. The orientations of the single crystals were such that <loo> was parallel to the growth direction, and (100) in the horizontal plane for lead, and [1101 and (110) respectively for tin. With these orientations long dendrite stalks formed along the bottom of the boat in the dendrite direction (<100> for lead and [I101 for tin) from which secondary branches grew. Only these secondary branches, which grew freely in the liquid from the dendrite stalk to the liquid surface, were used in the measurements. Accordingly, effects due to substrates and oxides on the surface of the liquid need not be considered. In order to measure the solute concentration C, of the dendrites, individual dendrite stalks were cut from the decanted specimens, remelted, and formed

Jan 1, 1962

By E. W. Cawthorne, R. I. Jaffee, C. M. Craighead

SOLUTION of a solid metal or alloy in a molten metal bath is used daily in melting operations, extractive metallurgical processes, and in brazing. It is generally recognized that temperature, time, agitation, and the composition of the solute metal and the solvent bath all affect solution rate. However, there is little information available in the literature on the kinetics of the process or the relative effect that these variables have on solution rate. In connection with an aluminum brazing study, data on the solution of aluminum in an A1-Si* bath to promote rapid solidification. The chemical analyses were made on drillings taken from the cast plates. The results of this work are listed in Table I. The thermal-analysis data were obtained on 200 gram samples cooled at approximately 1.5" per min. A calibrated chromel-alumel couple was used. The thermal arrests were recorded autographically on a General Electric photoelectric potentiometer recorder. The instrument was calibrated to 22.5 pct. The thermal emf was bucked with a Leeds and Northrup semiprecision potentiometer so that 1 mv represented the full scale of the GE recorder. Referring to Table I, it will be noted that the analytical results tend to be lower than the intended compositions by about 0.3 pct Si in the higher ranges. In view of the known difficulties in obtaining accurate silicon determinations by wet analysis when the silicon content is high and in view of the care that was employed in weighing and preparing the alloys, the intended compositions are believed to be more accurate than the analyses. Furthermore, when the thermal-arrest data are plotted against the intended compositions, a smooth curve is obtained, as shown in Fig. 1. This is not the case when the data are plotted against the analytical results. It will be noted from Table I that the 12.5 pct Si alloy (melt 4) showed a primary arrest at 577.6"C and the eutectic at 576.l°C. The metallographic examination of this chill-cast plate sample showed a small amount of primary silicon. These results, Fig. 1, place the eutectic at slightly less than 12.5 pct Si and are in rather good agreement with the unpublished Hanford data. In all of the subsequent work, the composition of the A1-Si dipping baths was determined by thermal analysis (spread between the primary arrest and the eutectic temperature) employing 12.5 pct Si and 577.2 °C as the composition and temperature of the eutectic. Material Preparation and Selection of the Techniques: At the beginning of this work, it was anticipated that, owing to oxide film present on the surface of the aluminum, difficulty would be encountered in obtaining rapid uniform wetting of aluminum specimens dipped in the A1-Si bath. The following etchants were investigated as possible methods of providing a thin uniform oxide film on the specimen surface: 1—phosphoric acid (H³O4), 2—fluoboric acid (HBFI), 3—sodium hydroxide (NaOH), and 4—hydrofluoric acid (HF). Tests with sheet .specimens (2x½x0.06 in.) of 2s aluminum prepared with these etchants indicated that the fast uniform wetting required for this work could not be obtained if any oxide film existed on the specimen surface. Tests were then conducted by dipping similar specimens etched in 5 pct NaOH and given a thin

Jan 1, 1956

By W. A. Jr. Slippy, E. P. Dahlberg, R. B. Reed-Hill

A large room-temperature mechanical-hysteresis effect under cyclic tensile loading was observed in zivconium specimens prestrained at 77°K so as to form large numbers of (1121) twins. The observed hysteresis loss was a maximum when the prestrain was just under 1 pct It also depended strongly on the maximum applied cyclic stress, but only moderately on loading rate and temperature (-72°to 100°C). The phenotnena have also been studied in terms of the elastic aftereffect where the data has been found to cotlforln closely to the functional relationship between strain and time, c = -RT/a In tank ft. t to)/Zr, for strains cts large as about 10-4 This eyication can be derived directly from the strain-rate equation There may be important commercial implications to the present discovery since it appears that within rather wide limits it may be possible to obtain any desired magnitude of damping capacity in zirconium melal. The damping propevties may also be given directional characteristics. It is shown that the observed anelaslic phenomena can he explained on the assumiplion that they are the resuilt of stress-induced twin-boundary movements in which the average twin increases its thickness by only a few percent. In polycrystalline zirconium, a grain is least favorably oriented for slip when its basal plane, containing the (1130) slip directions, lies nearly perpendicular to the principle normal stress. Mechanical twinning is favored by this orientation and under simple tensile deformation at room temperature the primary twinning mode is {1012).&apos; The (1012) twinning shear is small (0.17) so that, during deformation, twin growth does not greatly enhance ductility. At 77°K, on the other hand, the predominant twinning mode shifts to {1121), and many thin (1121) twins can form at small strains.&apos; Twins thus nucleated can grow readily during subsequent room-temperature deformation and permit easy deformation in unfavorably oriented grains. In addition, the (1131) twinning shear is large: 0.63. These facts have lead to a process&apos; for greatly improving the room-temperature ductility of zirconium when it contains a sizable fraction of grains with basal planes nearly normal to the stress axis. Optimum results are obtained by slightly less than 1 pct prestrain. The effect is large so that a 50 pct elongation increase is readily attained. A large room-temperature mechanical-hysteresis effect has also been observed in zirconium specimens prestrained at 77°K. The present paper is concerned with some aspects of this effect which the experimental observations strongly indicate is primarily the result of strain-induced {1121) twin-boundary movements. This clearly suggests that mechanical twins formed by plastic deformation can cause anelastic effects similar to those previously observed2 for annealing twins and twins associated with phase transformations. EXPERIMENTAL PROCEDURES All specimens were prepared from arc-melted sponge zirconium plate stock as previously described,3 which has a preferred orientation with basal planes aligned parallel to and uniformly distributed around the rolling direction. Both lonti-tudinal and transverse tensile specimens, with axes parallel and transverse, respectively, to the plate rolling direction, were cut from this plate. In a longitudinal specimen most grains are favorably oriented for slip, while in a transverse specimen a large fraction are unfavorably oriented. Prestraining at 77°K was performed in two ways. In one, annealed zirconium plate stock was cooled in liquid nitrogen and then rolled in the transverse plate direction to strains varying from 0.5 to 12 pct. Cylindrical 1/8-in.-diameter by 1-1/4-in.-gage-length tensile specimens were machined from this material. In the other, previously machined tensile specimens were prestrained in tension at 77°K between 0.2 and 3.8 pct. Type FA 25-12 SR4 strain gages were cemented to all specimen gage sections. All tests were performed on an Instron testing machine of 10,000-lb capacity. EXPERIMENTAL RESULTS Fig. 1 shows a typical two-cycle room-temperature stress-strain diagram for a specimen prestrained 0.65 pct by rolling at 77°K. The maximum stress in both cycles was 14,500 psi. Note that in the first cycle the loading and unloading curves are unsymmetrical so that a residual strain, er, remains after unloading. In the second cycle the stress-strain curves form a nearly symmetrical hystere-

Jan 1, 1965

By E. S. Machlin

An extension of the thermodynamic theory has been made for the case of irreversible growth processes occurring by the motion of an interface. The theory is applicable to such diverse phenomena as diffusion, growth in recrystallization, continuous grain growth, growth of carbides, etc., growth of eutectoid products, growth in solidification, recovery, "slipless" flow, etc. THE publication of a recent book1 has served to focus attention on a very powerful means of treating certain irreversible processes. This method which has been formally described as the thermodynamic theory of irreversible processes is applicable to processes which involve an approach to equilibrium and for which the deviations from equilibrium are small. The irreversible processes can be classified into three groups: chemical reactions, transport processes (diffusion, heat and electrical flows), and relaxation phenomena involving a degradation of internal energy to more stable states. The limits of applicability of the theory can be precisely defined1,2 for each type of irreversible process. For example, in a chemical reaction at constant temperature and pressure, the Gibbs free energy released per mol in the process should be less than the thermal energy, RT. Another type of irreversible process, which sometimes involves a combination of the first two of the above-mentioned groups, is treated in this paper. This process is one characterized by the motion of an interface separating two regions having different values of free energy and may be briefly described as a growth process. Prigogine2 and Herring3 have treated special cases of this type of process. Previous conscious applications of the theory in metallurgy have been limited to the field of diffusion, one of the transport processes. Darken,4 Bardeen,5 Prigogine2 and others have made significant contributions in this respect. Some other applications of the theory are described in this paper. The Theory The thermodynamic theory of irreversible processes is based on the work of Onsager,6 DeDonder,7 Prigogine2 and others. A resume of the theory has been given by Prigogine2 and DeGroot.1 A brief description of the theory follows, although for a complete understanding the reader is urged to read the references. It is first assumed that the change in entropy, even for a system removed from equilibrium, is given by dS = [dU + pdV - Si µi, dn, - Sk Pk dxk]T-1 Using this expression, the irreversible entropy production in the system is calculated by subtracting the contribution to the change in entropy of the system by transfer of heat, work, or matter from the surroundings. Thus, for example, the irreversible entropy production of a system at constant temperature and pressure is given by dtS = — — dG (DeDonder7) Now it has been shown by Prigogine,2 DeDonder,7 and DeGroot1 that the rate of irreversible entropy production diS/dt, when calculated in the manner suggested, can be written as a sum of products of conjugate forces XK and fluxes Jk, i.e., d,s/ = Sk Jk Xk [I-1] dt The assumption is next made that a linear relation exists between a given flux and the forces, obtained from Eq. I-1, i.e., Ji = Sk Lik Xk (i = 1, 2, . . . n) [I-2] Generally, there is a degree of freedom in choice of the fluxes and forces. However, for all the choices consistent with Eq. I-1 the Onsager8 relations, based on the principle of microscopic reversibility, namely, Lik = Lki, are valid. The coefficients Lik, depending upon the choice of the conjugate fluxes and forces, may be more or less dependent upon the parameters defining the state of the system. In general, the proper choice of fluxes and forces utilizing Eq. I-1, makes the coefficients Lik independent of time. Also, because many of the three classes of irreversible phenomena have already been treated,1,2 a proper choice can be made by analogy. In any case, the validity of Eq. 1-2, from whatever choice made using Eq. I-1, must be tested by experimentation. The theory, thus, comprises the following steps: 1—The irreversible entropy production is calculated to yield Eq. I-1. 2—The terms in Eq. I-1 are grouped

Jan 1, 1954

By W. C. Hittinger, J. McGlassan, J. W. Peterson

THIS paper describes the result of an investigation of the production of thin alloyed layers on a thicker substrate of pure germanium as one step in the manufacture of transistors.&apos; The technique of alloying materials with semiconductors is a means of introducing small amounts of impurity elements in the alloyed regions of the crystal lattice of the semiconductor, the presence of which make possible the junction type transistor.2 Impurity elements are added which will produce regions having differing electrical resistivities and means of carrying current. Impurities are of two types: those which produce an excess of electrons (negative or n-type), and those which produce a deficiency of electrons (positive or p-type) in comparison to the pure semiconductor. The boundary between two such regions is designated a p-n junction. Elements in Group V of the periodic table, having five valence electrons, give rise to an excess of electrons when present substitutionally in the semiconductor lattice (usually germanium or silicon from Group IV). Similarly, elements in Group III create a deficiency of electrons. Germanium and silicon which are substantially free of impurities of either p or n-type are designated intrinsic (i-type) semiconductors. The usual junction ----trarnsistor has

Jan 1, 1958

By V. Balasubarmanian, Rajendra Kumar

ISOTHERMAL formation of martensite in a copper-aluminum-nickel alloy was previously reported by Hull and Garwood.&apos; In the present work an attempt has been made to investigate some of the character- istics of the formation of isothermal martensite in binary copper-aluminum alloys containing 14.00 and 14.50 pct Al, respectively. Chill-cast alloys were prepared from OFHC copper and aluminum of greater than 99.5 pct purity. They were homogenized for 24 hr at 950° C. Polished samples were soaked at 1000°C and quenched in water to retain the p phase untransformed; martensite did not form during the quench. The surface was then repolished for isothermal microscopic studies at room temperature. The salient features of the martensitic transformation in copper-aluminum alloys observed in this investigation are: a) The transformation progresses (i) by nuclea-tion at new sites and (ii) by simultaneous slow isothermal growth of existing martensite plates. Slow isothermal growth of martensite has previously been observed by Holden2 in an uranium-chromium alloy and by Hull and Garwood in copper-aluminum-nickel alloy. b) Martensite plates nucleate preferentially at the pin holes formed during the casting of the specimen, Fig. 1. c) Some of the martensite plates pass right through other plates lying in their path, Fig. 1. d) Martensite plates cross grain boundaries without any change in the direction of growth. e) An irregular network of markings, Fig. 2, appears simultaneously with the formation of martensite. It was less prominent in the case of 14.5 pct alloy. The markings may arise due to spontaneous deformation under the lattice strains of the martensitic transformation. Crossing of martensite plates was first observed by Kulin and cohen3 when a high-nickel steel was cooled to 77°K. They suggested that the rapidly advancing plates atquire considerable kinetic energy and strike the obstructing plate with a momentum so as to nucleate the process on the other side of the plate. This, however, fails to explain the present observation where the slow isothermally growing martensite plates cross each other. Such plates would not possess large momentum to bodily displace the obstructing plate. Fig. 1 shows the martensite plates crossing each other without body displacements. This should be contrasted with Fig. 3 of Kulin and Cohen&apos;s paper where crossing of plates is accompanied by shearing or body displacements of the plates. The present observations can, how-

Jan 1, 1961

By R. G. Treuting

Germanium single crystals strained in tension at 600°C slip on the {Ill} plane and, macroscopically at least, in the <110> direction. Deformation is in homogeneous: various localized rotations are observed, as is a banding consistent with secondary slip banding. The structure after deformation is polygonized with a domain size of about 2x1O-3 cm. In relaxation tests, an incubation period prior to flow is observed, of duration inversely related to temperature and applied stress. Under continuous loading, there is a sharp first yield point. A critical resolved shear stress therefore must be cited with respect both to temperature and to rate of loading. At 600°C, when loading proceeds at 2900 psi per min, it is 1310 psi. The yield point phenomenon is suggestive of Cottrell&apos;s solute atom atmosphere theory and five points of qualitative agreement with this theory are found. PLASTICITY of germanium at elevated temperatures has been reported by Gallagher,&apos; who ascribed it to slip on {Ill) planes and described some associated effects. Preliminary experiments with single crystals of silicon and germanium loaded as simple beams confirmed {ill) as the slip plane of both materials.V his was demonstrated by the standard technique employing traces on two surfaces of known angle on a deformed crystal of known orientation.3 These experiments did not fix the slip direction, since more than one glide system operated. Uniaxial tensile straining is preferred for this purpose in order to restrict slip to one predominant system and to provide an unequivocal determination of the orientation change with respect to the stress axis. Experimental Method Specimens were diamond-sawed from germanium crystals containing about 5x10-5 wt pct Sb prepared by the zone-leveling process described by Pfann and Olsen;4 these specimens measured about 81/2 in. long, 0.20 in. wide, and were of various thicknesses from 0.035 to 0.060 in. Prior to testing, a specimen was coated over 1 in. or more of length at each end with Apiezon wax, chemically polished (in a solution of 15 ml HF, 25 ml HNO,, 15 ml CH3COOH, and 3 to 4 drops Br2), and dewaxed in warm xylene. A brief re-etching after scribing through a complete wax coating with vernier dividers provided gage marks at 0.200 in. intervals on the polished surface. A specimen with grips soft soldered to the ends was passed through the furnace tube and the grips pinned to the tensile machine in series with a stress gage. The Schopper testing machine is best described by reference to the illustration on p. 107 of Schmid and Boas5 and is operated with the pendulum arm locked, fixing the upper head. Load is applied through the screw-driven lower head, manually or by reduced speed motor. The furnace is 21/2 in. long surrounding a 4x7/16 in. ID quartz tube and was positioned about the specimen to permit free motion. The inert or reducing atmosphere required was sufficiently provided by a flow of helium introduced at the center of the furnace tube, with the tube ends loosely plugged with asbestos paper. Surface corrosion was slight. The stress gage employs a Be-Cu strip with SR-4 units incorporated in a simple bridge network with provision for balancing and calibrating. The bridge output on loading is fed through a Leeds and North-rup dc amplifier to a Speedomax 10 mv recorder, and calibration is obtained by dead loading. Experiments of two types have been conducted. Most have been in relaxation at constant elongation. One stress-strain curve has been taken with the machine continuously driven. Following extension of a specimen, Laue X-ray photographs were taken to obtain the orientation change between deformed and undeformed regions, recorded on a single film by translating the specimen in a plane normal to the beam between exposures. Sequences of such multiple exposures were made on some specimens to include the entire orientation range on one film. Slip Direction To obtain a maximum orientation change with a single slip system, crystals of very closely <110> axial orientation were used. The classic determination of slip direction rests on establishing that direc-

Jan 1, 1956

By N. E. Brown, F. L. Versnyder

THE apparent dependency of the electrical characteristics of hexagonal crystalline selenium on microstructure has aroused much interest in microscopical studies of selenium. Microscopic observations on the crystallization of selenium have been made by Escoffery and Halperin,&apos; P. H. Keck,&apos; and other investigators. It is the purpose of this paper to discuss the microstructural changes observed on polished cross-sections of single layers of selenium after various heat treatments. Observations were also made on crystallization of the free-surface layer of these deposits. In general, all of the transformations studied were either transformations of the vitreous selenium to hexagonal selenium or micro-structural transformation of the hexagonal selenium itself. Procedure The selenium used in this work was obtained from the American Smelting and Refining Co. and was approximately 99.96 pct pure. An intentional impurity of 1 part per 2,000 of bromine was added to the material prior to evaporation. A thickness of approximately 0.002 in. of this selenium was vapor deposited on an aluminum base plate. The maximum plate temperature during the vacuum vapor deposition was 140°C. Mounting of the cross-sectional specimens for metallographic study could not be done in plastic mounting media, as is customary, since temperatures in excess of 50°C would cause unwanted transformations. Consequently, a simple clamp-type device was used to mount the specimens for preparation. All grinding operations were then done carefully by hand in order that the specimen not become heated during this operation. Wet polishing was done on the conventional metallographic polishing laps, using successively finer grinding powders. An extremely careful polish is necessary, since observation and micrography of the specimens are done in the unetched condition under polarized light. The two observations of crystallization made on the free surface of vitreous selenium deposits (Figs. 4 and 5) were made on surfaces which were perpendicular to the cross-sections studied. These free-surface layers were examined directly, i.e., no pre- vious metallographic preparation, as obtained from the vacuum vapor deposition. Microscopic Observations A study was made of polished cross-sections of the vitreous selenium as-deposited. It was noted that in all cases there was columnar crystallization adjacent to the base plate, which appeared to occur during the vacuum deposition process. This observation has also been made by Keck? It also was observed that vagrant spherulitic crystallization occurred in the vitreous selenium. The term "vagrant" is used, since these spherulitic grains appear to crystallize at random throughout the vitreous selenium during the vacuum deposition process. Columnar crystallization at the A1-Se interface and a typical spherulite observed in a polished cross-section of "as-deposited" vitreous selenium may be seen in Fig. 1. Cross-sectional samples of vitreous selenium studied after heat treating individual samples for 20 min in 10" steps from 80" to 220°C revealed that crystallization—in this case, columnar crystal growth —proceeds from the aluminum base plate to the surface of the specimen (Fig. 2). Crystallization was microscopically observed to be complete after the 130°C heat treatment. Visual examination of the free surface of the specimen after the 130 °C heat treatment revealed the readily recognizable grey appearance of the completely crystallized selenium, in corroboration of the microstructural observations. No microstructural transformations then appeared to take place between 130" and 190°C. At 190°C the beginning of recrystallization appeared and proceeded until the columnar grain structure had been completely transformed to equiaxed grains between 210" and 220°C (Fig. 3). Naturally, the grain size of the recrystallized grains at the lower temperatures (190" to 210°C) was smaller than is illustrated in Fig. 3. In addition, polished cross-sections of deposits heat treated at 140°C for 10 min to cause complete crystallization and, subsequently, heat treated in 10" steps from 80" to 220°C for 20 min were studied. As expected, no microstructural transformations took place until the beginning of recrystallization was observed at 190°C. A comparison with the previously studied specimens revealed that recrystallization proceeded almost identically in the two experiments although in the first case the deposits were vitreous prior to the series of heat treatments and in the second case they had been crystallized by a previous heat treatment. By heat treating for longer times (180 min) at lower temperatures, the

Jan 1, 1956

By R. D. Carnahan, J. E. White

ThE use of strain gages in the measurement of microplastic behavior of materials is well-known.&apos;-3 Recently it has been suggested that similar techniques might be useful for determining stress relaation. It is the purpose of this report to comment on the use of strain gages in the measurement of strains in the vicinity of 10"6. We will also discuss observations of an anomalous anelastic behavior apparently associated with small temperature changes, which accompanies the unload portion of a load-unload microstrain test. The key to successful strain determinations at levels below 1 pin. per in. is a good gage-mounting technique and either precise ambient temperature control or a set of matched temperature-compensated gages. The importance of good mounting cannot be overemphasized, for example, as in the use of Eastman 910 contact cement. If the cement layer is not sufficiently thin and properly hardened, it is possible to observe anomalous negative stresses when small loads are removed, which relax back to zero in an orderly way with time. Such anomalous behavior, thought to be due to gage bonding, has been reported in microstrain experiments by Thomas and verbach&apos; who observed a negative strain of -3 X lo-&apos; upon unloading. This kind of behavior severely limits the over-all strain sensitivity which can be achieved in such tests. The relaxation of a small positive strain subsequent to unloading in a load-unload experiment is quite normal, however, and is to be expected. The occurrence of an apparent negative strain is also encountered in those instances where the elasticity of the bonding cement is exceeded—for example 0.5 pct or 5000 pin. for cured Eastman 910. An elastic strain of this magnitude can be encountered during load-unload type testing particularly in higher-strength materials (-150,000 yield strength). During the course of microplasticity studies on pure nickel and nickel alloys,&apos; the authors have made the following observation. In a four-point bending test, two active gages are mounted one on each side of the beam as arms R1 and R z of a conventional strain-gage bridge circuit shown in Fig. l(a). This technique provides two advantages: the sensitivity is doubled because R1 and Rz experience opposite strains and temperature compensation is provided automatically because any ambient temperature change would cause both gages to see a strain of like sign whose signals would cancel in the circuit.

Jan 1, 1964

By G. D. Gemmell

Effects of solid-sdutidn alloying with titanium, molybdenum, and tungsten at concentrations up to 10 pct on the strength of pure columbium at elevated temperatures (mainly 2000°F) have been investigated by means of creep-rupture, hot-tensile, and hot-hardness testing and recrystallization studies. ThIS paper presents some results from the initial part of a study of the effects of alloying on the high-temperature strength properties of columbium. The elevated-temperature strength characteristics of pure columbium were first studied. Binary alloys of columbium with titanium, molybdenum, and tungsten containing 1, 5, and 10 pct of the solute elements were chosen on the basis of their high melting points, their known solid solubility in columbium, and results of separate oxidation-resistance studies of columbium alloys. EXPERIMENTAL PROCEDURE All the materials used were of highest purity. A typical analysis of the columbium is shown in Table I. Compositions of the alloys are also given in Table I. To evaluate the strength properties of pure co-lumbium and the alloys at elevated temperatures, creep-rupture, hot-tensile, and hot-hardness testing was done on recrystallized material. To prepare the pure metal and the alloys for these tests, 1- 1b buttons were made in a water-cooled copper crucible, inert atmosphere, tungsten arc furnace. Tapered ingots, 3 in. long, were made from these buttons by a skull-casting technique and these were machined to 1/2 in. diam, swaged to 50 pct reduction (pure columbium at room temperature, alloys at lowest temperature possible without cracking, generally in range 1100" to 1800°F) and heated in vacuum (lo-&apos; mm Hg) for 16 hr at 2550°F for re-crystallization and homogenization. The resulting grain diameter was 0.1 to 0.3 mm. The 10 pct Mo alloy casting was not successfully swaged at temperatures up to 1800°F without cracking and was not included in the test program. Creep-rupture testing was done at constant load in vacuum on cylindrical specimens of 0.16 in. diam, using Instron capsules. The pressure at test temperatures was less than 10-1 mm Hg. Hardneas readings taken on the test specimen before and after testing were used as a check on possible gaseous contamination. Hot tensile tests in vacuum on cylindrical specimens of 0.125 in. diam were also made with Instron equipment at a strain rate of 0.067 min.-l. Hot-hardness measurements were taken with a unit constructed at the Du Pont Experimental Station. The test piece, supported on an alumina anvil, and the molybdenum indenter shaft with sapphire tip is heated in a platinum-wound furnace. The load applied to the pyramid indenter is measured by strain gages attached to a proving ring located outside the hot zone. In the measurements reported here the load was I kg. The tester operates in a vacuum of about 10"5 mm Hg and is capable of temperatures up to 1400°C.

Jan 1, 1960

By G. H. Enzian

THE effects of phosphorus and nitrogen on the properties and behavior of low carbon steels are important considerations to both the manufacturer and the user of such material. For one thing, these two elements are the principal points of distinction between the chemical compositions of Bessemer and open-hearth grades. Further, open-hearth steels themselves may vary considerably in nitrogen content depending on the raw materials and ..practice used. In addition, appreciable amounts of rephosphorized open-hearth steels are being used at the present time in some low alloy, high strength grades and in certain other cases. For these and other reasons, it was felt desirable to obtain more complete knowledge of the effects of simultaneous small variations in phosphorus and nitrogen content on such properties of low carbon steel as tensile strength, impact toughness, sensitivity to cold work, and strain aging. A long range investigational program designed to furnish such information, was carried out, and the present paper summarizes some of the data currently obtained. General Discussion The strengthening effect of relatively small amounts of phosphorus in steel has been recognized, and to some extent utilized, for many years. A number of investigators have pointed out, from time to time, that under proper conditions of control, phosphorus can be a useful alloying element in low carbon steels.1-3 Nevertheless, in spite of the volume of data on the subject, the use of phosphorus for this purpose has always been handicapped by widespread feeling that its presence makes the steel brittle, difficult to cold work, and unreliable at low temperatures. This belief on the part of some steel users is not entirely justified in many cases, and often stems from early experience with acid Bessemer steels which have appreciably higher phosphorus (and nitrogen) contents than basic open-hearth grades. Nitrogen in steel, and its effect on properties, has also received considerable attention in the literature.4 In 1906, Braune5 ascribed the brittleness of Bessemer rails to the nitrogen content, and proposed a schedule of nitrogen limits for steels for various uses. This was one of the first papers to recommend directly the use of nitrogen content as a quality control measure, but it did not meet with much favor or support; as a matter of fact, the Jernkon-toret was rather sharply criticized for publishing the paper. In the intervening years a number of papers have been published on the subject of nitrogen in steel. As a result, it is now generally recognized that nitrogen can have an important effect on the properties and behavior of steel and that the presence of this element should be considered in any systematic study of factors affecting steel quality. In 1932, Graham6 introduced the concept that the quality of various steels could conveniently be evaluated and compared in terms of "sensitivity", which was defined as "the characteristic reaction rate of a piece of steel toward brittleness or hardness." This concept formed the basis for a broad research program into factors causing variations in the quality of commercial steels. At an early stage of this work, it became apparent that the observed effect of either phosphorus or nitrogen on the sensitivity of steel depended, in no small measure, on how much of the other of these two elements was also present. Indeed, the combined effect of phosphorus and nitrogen in steel may often be more important than the specific effect of either. With a few exceptions, it is not possible to predict accurately the effect on steel properties of a change in the amount of either phosphorus or nitrogen in the steel without also specifying the approximate amount of the other element. It seems desirable, at this point, to discuss briefly the distinction between strain-sensitivity and strain aging as used in this paper. In the early stages of its development, the work-brittleness test7 (which will be described in more detail later) was used

Jan 1, 1951

By G. H. Enzian

W. C. Ellis—The intergranular fracture observed by these authors in brass seems to be characteristic of metals when tested under similar conditions. It has been observed by us in room temperature tests on lead alloys subjected to constant stress when the stress has been low enough to afford a small strain rate. If, however, the test be carried out at a high stress and therefore at a large strain rate, a characteristic, tapered, transcrystalline fracture is obtained. The same change of fracture has been observed by others with decrease of strain rate and increase of temperature for other metals—for example aluminum—and may be presumed, as the authors point out, to be general for metals. These findings suggest a plastic flow mechanism under conditions of small strain rate and high corresponding temperature differing from classical block slip. The required conditions point to a process fundamentally diffusive in nature—a less organized process than block slip. Nabarro18 has shown that plastic flow can occur by stress induced diffusion of vacant sites— a process of self-diffusion. Movements of a pseudo-viscous nature at grain boundaries are suggested in the work of Ke.15 Deformation near to a grain boundary by other than a slip mechanism appears necessary to Boas and Hargreaves.19 Wood and Rachinger20 report a cellular structure in slowly deformed alumi- num—the cell size is larger, the higher the temperature and the slower the strain rate. Presumably in the latter case diffusive movements occurred in the cell boundaries. In any case the nonslip mechanism seems somewhat obscure and further work is indicated. Such studies will undoubtedly clarify the nature and behavior of lattice imperfections—the very core of the strength and plastic properties of metals. F. H. Wilson and E. W. Palmer (authors&apos; reply)—It is certain that the metallic behavior which has been termed "creep" includes many interdependent phenomena of which a nonslip type of plastic flow may well be one. The reports to which Mr. Ellis refers are illustrative of the many different observations that must be correlated for a complete understanding of creep. The list could be extended considerably. For example, we ourselves have been impressed by the sensitivity of creep phenomena to the presence of minor impurities and feel that this aspect of the problem warrants more thorough study than it has yet received. References 18 F. R. N. Nabarro: Report of Bristol Conference on Strength of Solids. P. 75, (1948) London. 19 Boas and Hargreaves: Proceedings Royal Society. (1948) 193. 89. 20 wood and Rachinger: Journal Institute of Metals. (1949) 17, 237.

Jan 1, 1951

By P. W. Davies, B. Wilshire

PREVIOUS investigations on the effect of stress changes on the high-temperature creep and fracture behavior of metals have been confined mainly to the testing of complex alloys.172 Most of these alloys are structurally unstable during creep because of such effects as recrystallization, overaging, and so forth, so that the results are of limited application. The only pure metals on which observations have been made appear to be lead3,4 and aluminum5 tested under conditions which allow rapid recovery to take place. The present work describes the effect of a single stress change on the creep and fracture properties of a metal in which recovery is very slow. A Ni 0.1 at. pct Pd alloy was used so that grain growth and recrystallization did not occur during creep testing. Specimens of this material were heat-treated to give a uniform grain size of 10 grains per mm. Creep tests were carried out at 500°C using Denison T.47 machines; details of the creep-testing procedure have been given elsewhere.&apos; All specimens were tested at a constant initial stress of 5 tpsi which gives, in an uninterrupted test, a minimum creep rate of ~10-3 pct per rnin and a life of -7000 min. Specimens were loaded under these standard conditions and after 1500 min, when secondary creep was well-established, the stress was changed to either 8, 7, 6, 4, 2, or 0 tpsi for a period of 180 min. After this time the original load was reapplied and the tests continued to fracture. The results are shown in Fig. 1. No detectable creep occurred during the period of reduced load, even at 4 tpsi, and on reverting to 5 tpsi the creep rate returned to its original value immediately. Increasing the stress to 8, 7, or 6 tpsi resulted in an instantaneous extension followed by a period of transient creep leading to a new steady creep rate. On returning from these higher stresses, the resulting creep rate at 5 tpsi was very low compared with the original value. Furthermore, the higher the stress during the stress change, the lower was the final creep rate. It is significant that the rupture life is comparatively unaffected by any of these stress changes.

Jan 1, 1965

By Edward E. Hicke, Charles A. Stickels

The dihedral angle of liquid-lead inclusions in solid nickel has been measured as a function of temperature from 371 to 816 C at zero pressure. and as a function of pressure up to 50,000 psi at 317 and 593 C. Thermodynamic expressions are derived for the temperature and pressure coefficients of interfacial tensions in this system. A method is presented for obtaining relative tempmature and pressure coefficients from dihedral-angle data, and the resulting values are used in conjunction with the thermodynamic relations to calculate excess properties of the solid-liquid interface. Defining the position of the solid-liquid interface by the condition that the excess concentration of lead is zero, the excess concentration of nickel and the excess entropy at the solid-liquid interface are: where y(593) is the interfacial tension of the nickel grain boundary saturated with lead at 593C and zero pressure. These values are considered reliable to within a factor of two. While similar calculations are not possible for the nickel grain boundary, it is shown that the expwimental results imply that the excess concentration of nickel at the boundary and the excess entropy of the boundary are negative. THE temperature and composition dependencies of interfacial tensions in metal systems have been reported by several authors in the last 15 years.&apos;-&apos; No measurements of the effect of pressure on inter- facial tensions in metals have been reported, although measurements made on nonmetallic gas/liquid and liquid/liquid systems suggest that a measurable effect should exist.6-l2 The purpose of these experiments was to determine the influence of temperature and hydrostatic pressure on dihedral angles in the Pb-Ni system. The equilibrium dihedral angle is expressed as a ratio of interfacial tensions by2: where 8 is the dihedral angle, yGB is the Ni-Ni grain boundary tension, and SL is the solid Ni-liquid Pb interfacial tension. Three sets of ex- periments were run to determine: a) the effect of temperature from 371" to 816°C on the dihedral angle at zero pressure; b) the effect of pressure up to 50,000 psi on the dihedral angle at 371° and 593°C. THERMODYNAMICS The properties of interfaces of most direct concern are the interfacial tension, excess concentrations of various components at the interface and the excess entropy of the interface, S°. These quantities are defined following Gibbs. Consider an interface separating phases a and 0. Construct two surfaces C, and C such that all properties of phase a remain uniform up to C, and all properties of phase 0 remain uniform up to C. The region between C, and Cp is the interfacial region. Let a "dividing surface", D, be constructed in the interfacial region such that it passes through all points "similarly situated with respect to the condition of the adjacent matter."l3 Surface D divides the interfacial region into a portion a&apos; adjacent to phase adjacent to phase . Let a closed curve, C, enclose an area A in D. Erect normal lines to D along C; these lines and the surfaces C,, Cp, and D then enclose volumes V and V&apos; in the two halves of the portion of the

Jan 1, 1964

By A. W. Cochardt

MOST of the current high temperature materials are precipitation-hardened alloys. These alloys are usually soft when quenched from a solution heat-treatment temperature, but become harder

Jan 1, 1958

By Robert E. Green

Experiments were performed in order to investigate the influence of magnitude of driving force, recouery, and previous heat treatment on grain boundary migration in deformed aluminum crystals. The frequency of occurrence of strain-free grains possessing Preferred crystallographic orientations was studied both as a function of heat treatment and as a function of amount of deformation of the matrix crystal. Aluminum of such composition as to exhibit precipitation-hardening behavior was used. CONSIDERABLE work has been devoted to the factors influencing grain boundary migration in metals.1&apos;52 Aust and Rutterl-9 have studied grain boundary migration into matrix crystals containing a striation substructure, which provided a thermally stable driving force during the course of the migration experiments. These authors state that, while variations in the striation pattern were sometimes observed, it was possible to obtain reasonably uniform and reproducible striation structure by careful control of the solidification conditions. Admittedly, this source of driving force is a unique one and has served well in numerous experiments. However, although the striation substructure provides a thermally stable driving force, the subject of its reproducibility from crystal to crystal is questionable. In fact, Aust and Rutter3 attribute the scatter shown in some of their experimental points and several anomalies in boundary migration rates to variations in the substructure driving force along a single specimen. A further limitation on striation-induced driving force is that the driving force cannot be varied over wide ranges in a controlled manner. More often used as a source of driving force is the strain energy stored in a crystal during plastic deformation. This type of driving force has the disadvantage that it is not thermally stable due to recovery taking place simultaneously with the grain boundary mobility measurements. On the other hand, this strain-induced driving force is very reproducible from crystal to crystal since it is very easy to grow single crystals possessing the same purity and crystallographic orientation and then to strain them identically. In order to measure grain boundary migration rates two different methods are primarily used. Most often the technique employed is the heat-cool-etch method1&apos; which involves thermal cycling, while the other technique, developed by Graham and Cahn11 using an X-ray diffractometer and goniometer furnace, involves continuous heating only. Thus the influence of thermal cycling vs continuous heating is a factor to be considered in grain boundary migration rate measurements, particularly in cases where the source of driving force is the strain energy stored in the deformed matrix, and recovery is likely to occur. Numerous recent investigations have shown that extremely small impurity additions to zone-refined metals exert a marked effect on grain boundary migration rates1-5, 9, 12-27 and a few have considered the effect of the distribution of impurities.28-35 The concentration of impurities and their distribution as influenced by heat treatment must also be taken into account in migration-rate studies. In the present article consideration is given to the influence of the magnitude of driving force, recovery, and previous heat treatment on grain boundary migration rates. In order to vary the driving force over a large range it was necessary to use as a source of driving force the energy stored in the matrix crystal during plastic deformation. A majority of the investigations were performed on aluminum specimens which were of such compositions as to exhibit precipitation-hardening behavior.

Jan 1, 1965

By M. J. Saarivirta, P. P. Taubenbla

This paper presents some high-temperature properties of copper-zirconium conductor alloy compared to copper-chromium alloy. Definite superiority of the copper -zirconium alloy over the copper-chromium alloy at high temperatures is shown. RECENT investigations have shown that cold-worked copper-zirconium alloy possesses good room-temperature strength, ductility, and conductivity and maintains most of its strength at temperatures up to 450°C (840°F). As a result, this alloy is now used for many applications, such as commutator segments, resistant welding wheels and tips, rectifier bases, electrical contacts, and so forth. Early investigations1-3 have shown that the maximum solid solubility of zirconium in copper is close to 0.15 pct and the alloy containing Cu-0.10-0.15 pct Zr exhibits the optimum mechanical and physical properties. Results2 have also shown that the alloy has better elevated temperature strength and ductility than copper-chromium and copper-silver alloys. The present investigation was undertaken to learn more about the elevated temperature properties of copper-zirconium alloy and to compare these properties with those of the copper-chromium alloy. WORK PROCEDURE The commercial copper-zirconium alloy, Amzirc was selected for this investigation. Because this alloy is composed of oxygen-free high-conductivity copper and 0.10-0.15 pct Zr, it was believed that possible disturbance from impurities would thus be negligible. Copper-chromium alloys used in this investigation contained 0.40 and 0.70 pct Cr and balance copper. The Cu-0.40 pct Cr alloy was a commercial brand, whereas the Cu-0.70 pct Cr alloy was made from OFHC copper and Cu-5 pct Cr master alloy. It was made in a graphite crucible under argon gas cover and cast. In the preparation of specimens, all three alloys were treated to give the optimum properties; thus the Cu-0.15 pct Zr alloy was solution annealed at different temperatures to determine the desirable solution annealing temperature. It was then cold worked and aged at 375" to 400°C (705" to 750" F). A solution annealing temperature of 1000°C (1830°F) was selected for the copper-chromium alloys because this temperature is widely used in commercial practice. The same alloy was aged at 450°C (840°F) after solution annealing and cold working. It was found that the maximum precipitation hardening of the copper-chromium alloy occurred at this temperature. When aged after solution annealing, the aging temperature was 500°C (930"F) for both alloys. The following properties were determined: 1) Tensile properties as a function of temperature. 2) Effect of solution annealing temperature on high-temperature tensile properties. 3) Stress to rupture strength at 350° and 400°C (660"to750°F). 4) Impact strength. 5) Electrical conductivity and resistivity as function of temperature. 6) Thermal expansion.

Jan 1, 1961

By Margaret V. Doyle, R. W. Powers

INTERNAL friction measurements, carried out as functions of temperature, have been used extensively to obtain data on the mobility of interstitial impurities in the Group V metals, vanadium, colum-bium, and tantalum. For a given frequency of vibration, the internal friction peaks at a temperature which depends principally on the particular metal and interstitial impurity. Relaxation times and corresponding activation energies are determined from a knowledge of such peak temperatures for various vibration frequencies. These experimentally determined relaxation times are related to the average jump frequencies of the interstitial impurity atoms using the model of Snoek1 and can be related to macroscopic diffusion coefficients as shown by Polder.2 In these Group V elements, the impurity whose diffusion rate has been the hardest to pin down by the internal friction technique has been carbon. The experimental difficulties associated with carbon in these metals were not evident in the earliest investigation carried out by Ke on tantalum.3 The carbon peak was thought to occur near 140°C at 1 cps on the basis of the enhancement of the height of this peak measured on specimens which had been coated with colloidal carbon and heated in vacuo at 1200°C. Presumably on the basis of similar evidence, Wert identified a peak also near 140°C at 1 cps in columbium with the diffusion of carbon in that element." Later, the difficulties of admitting carbon into these metals without simultaneously introducing oxygen were pointed out by Ang and Wert- nd by Marx, Baker, and Sivertsen.6 The latter suggested that the peaks attributed to carbon in tantalum and columbium might arise from the presence of traces of oxygen, adventitiously absorbed during the carburization. Such suspicion was confirmed, at least in tantalum, when it was found possible to prepare C-Ta specimens without contamination by oxygen. Specimens sci prepared, aitnough high in carbon content, gave no evidence of a damping peak near 140°C.7 Recently, the authors were able to Show that carbon diffuses in tantalum at a rate only slightly slower than that for nitrogen.8 At 1 cps, the carbon peak lies at 34g °C, only a few degrees above the nitrogen peak at 341 °C. However, the two could be distinguished by a different stability with respect to aging at 400 °C and by a different dependence of peak height on solute concentration. On the basis of this experience with tantalum, it appeared worthwhile to search also for a carbon peak in columbium in the vicinity of the nitrogen peak." In this report, the location of the carbon peak in columbium is made known and its position relative to the nitrogen peak is compared with the authors&apos; previous findings in tantalum. In addition, a second source of internal friction seen only in specimens of very high purity is discussed. Columbium was obtained from the Fansteel Metallurgical Corp. as either 30 or 40 mil diam stock. The manufacturer gives the following analysis as typical of this material: 99.4 pct minimum Cb, 0.10 pct maximum C, 0.5 pct Ta, 0.04 pct Ti, 0.02 pct maximum Si, and 0.01 pct maximum Fe. Wires 13 in. long were degassed near 2200°C for 4 to 16 hr in an ultimate vacuum better than 2.10" mm Hg in an apparatus described previously.8 This treatment reduced the oxygen and nitrogen damping peaks observed in the as-received material to less than 0.0001 in Q-1 above background. The latter value varied somewhat from specimen to specimen in the range 0.0004 to 0.0008, depending chiefly on the wire diameter and the frequency of vibration. The high temperature evacuation left the specimen in a rather soft condition, the Vhn being reduced to 40 from a value near 121 in the as-received conGi~iur~. The gram size was about the diameter of the specimen. After outgassing, specimens were loaded with carbon by absorption of such hydracarbons as methane or ethylene. Carbon was also added to a few speclrnens by heating them at

Jan 1, 1958

By G. Meyrick, H. W. Paxton

Observations on the tensile deformation of single crystals of austenitic stainless steels as a function of composition, orientation, and temperature are described and compared with relevant data for other alloys. Crystals free from second phases show sharp yield points followed by Lüders&apos; extensions of up to 20 pct. The critical resolved shear stress is strongly temperature-dependent increasing fourfold between 423O and 77°K. A temperature-independent low rate of hardening follows the Luders&apos; extension and is frequently associated with overshoot. Unlike pure metals where Proficse cross slip usually occurs at the end of linear hardening, this stage is terminated either by cross slip or by slip on the conjugate system, the particular node apparently depending upon initial orientation and composition. The presence of 6 ferrite or martensite has a profound effect upon the magnitude of the yield stress and the shape of the stress-strain curve. In experiments on transgranular-stress corrosion cracking of austenitic stainless steels in boiling magnesium chloride, several workers1&apos;2 have shown that increasing amounts of nickel tend to reduce the probability of specimen failure. Reed and paxton3 have observed in single crystals that the macroscopic crack plane changes as the nickel content is increased. For 18 pct Cr-8 pct Ni, the crack plane is sensibly perpendicular to the applied tensile stress; for 20 pct Cr-20 pct Ni the crack plane is (100). The average crack-propagation speed is much lower in the 20 pct Ni crystals. Furthermore, the possible importance of stack-ing-fault energy in nucleation and growth of cracks has been suggested by a number of workers. While the general effect of variations in stack ing-fault energy appears to be quite well-correlated with observed variations in cracking characteristics, each of the theories assigns rather different detailed reasons for these effects. Because the stack ing-fault energy of austenitic steels is believed to be increased with increasing nickel content, and because some theories of trans-granular cracking postulate a mechanical stage in the crack propagation (rather than relying entirely on electrochemical solution), it appeared to be of some interest to investigate the mechanical properties of a series of different compositions of aus-tenite single crystals. These experiments were considered of intrinsic value in view of the relative scarcity of such data on fcc alloys. This paper gives the results of some experiments carried out with this aim in mind, and suggests various &apos;other experiments which may be helpful in future studies. The experiments are also of interest in view of the recent interest in obtaining higher-strength steels by control of the imperfection content of austenite; although the compositions are not directly comparable, the results are still probably valuable. Comparisons with experiments on other fcc alloy crystals are made where possible to see how well the general pattern of behavior is understood. EXPERIMENTAL PROCEDURE The alloys used in this investigation were vacuum-melted heats of nominally 20 pet Cr-20 pet Ni-60 pet Fe, 20pctCr-16 pct Ni-64 pct Fe, and 20 pctCr-12 pet Ni-68 pet Fe.* Analyses of the material are

Jan 1, 1964

By Phillip A. Stoll, Young Ku Yoon

ThE deterioration of the magnetic properties of silicon-steel core materials during service (magnetic aging) is quite undesirable. Although some information about the effects of impurity elements on magnetic properties is available, 1,2 magnetic aging that occurs at low temperatures has not been extensively studied. Moreover, the microscopic techniques used by earlier workers were not suitable for study of fine metastable phases that are precipitated at relatively low temperatures. Recently, several investigators3,4 successfully used transmission electron microscopy in the study of low-temperature precipitation in Fe-C, Fe-N, and Fe-Mn-C alloys. To investigate metallurgical factors that affect magnetic properties after aging, the microstruc-tures of steels having different magnetic-aging

Jan 1, 1964