Search Documents

By Owen Rice

CHANGES in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. Soft coke is a great hindrance to proper blast-furnace operation and changes in coke hardness affect the working of the furnace. The best method of determining the hardness of coke is by using a combination tumbler-ball-mill. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged. An increase of this ratio improves the hardness of the resulting coke. WHAT IS GOOD COKE? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide, has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving

Jan 1, 1921

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

By Hal McVey

There are thousands of industrial minerals occurrences in the world. The existence or nonexistence of a market for the minerals from these deposits dictates whether or not they will be developed. Therefore, a market srudy is an integral part of the evaluation and development of an industrial minerals property. Some of the factors to be considered in a valid market study are: Supply & Demand; Transportation; Specifications; Competition; Substitutes E Alternatives; Price and Market Structure. Of these, Transportation and Specifications are of particular importance to market evaluations in the field of industrial minerals. The market researcher, working closely with technical personnel in geology, mining and processing, can determine the technical and economic acceptability of the product to be produced from the prospective property and can often create areas of opportunity for marketing of industrial minerals.

Jan 1, 1980

I am deeply honored and grateful to receive the prestigious Gaudin Award. Frankly, I find myself amazed to be included in the company of those outstanding individuals who have previously received this recognition. I am humbly honored to receive this award from an industrial research group. Gaudin was an internationally respected leader of mineral processing. His research contributions widely covered the whole spectrum of mineral processing science and technology, including comminution, size distribution, electrostatics, magnetics, thickening and, especially, the development of flotation theory and application. In his later career, he increased his emphasis on hydrometallurgical technology. In fact, one of his most notable practical contributions was in the development of leaching and ion exchange purification of uranium from low-grade ores. Gaudin catalyzed the trend in mineral processing toward engineering science for a better understanding of process mechanisms and kinetics. He said that those working in academic fields should have an underlying responsibility to the industry they represent. This imposed on him the objective of seeking out research areas that had some relevance to industry's problems. He said, "research without an audience cannot survive." Gaudin performed a most vital service, both in the areas of research in which he was actively involved and through his less-direct influence on current research by his many former students and their students in turn. Interestingly, Gaudin's strength has influenced Newmont Mining Corp. His favorite student was Plato Malozemoff. He had a long and distinguished career with Newmont, beginning as staff engineer in 1945, serving as Newmont's president for more than 30 years and as chairman of the company for 20 years. Newmont's greatest growth occurred during his leadership. Another one of Gaudin's graduate students from Montana School of Mines, Oscar F. Tangel, joined Newmont in 1967. He was a vice president of research and development until 1986. In their efforts, Newmont built a research group, developing the technologies of exploration, geophysics and metallurgy. The Newmont technical facility is named in honor of Malozamoff as "a leader in the development and implementation of new technologies." The mining industry is facing very difficult times, especially in the metals industry. Most metal prices have declined and are still not stable. Most domestic mining companies have largely done away with in-house research and development. Many are reluctant to invest in technology development for which there is not an immediate need. The metal mining industries are focusing on reducing operating costs to survive. Newmont is in the same situation. I appreciate that Newmont's management believes in the importance of research and technology and the impact technology has on the company's value. At Newmont, technology development involves working in the area of applied research. The connections from academic fundamental research to applied research and finally to process development and implementation are very important to develop a new technology. Fundamental research is our foundation, our guidance, giving us direction, providing the principal and mechanism and understanding why it works. Understanding the why will lead to further innovative development. Applied research needs to find the approach to reality, how it works, how to make it better and how to commercialize it. Process development and implementation needs a strong leadership, requires long-term commitment, makes improvements in practical engineering and finally develops an economically favorable process. Implementation is the most important stage in making research a reality. Each stage needs to give feedback to the other stages. Problems need to be understood and solved. Otherwise, the new technology will go nowhere. Simplicity of operation is a key of success in any plant. Necessity is the

Jan 1, 2002

[based on o report by HUBERT E. RISSER] There is a tendency among laymen to relegate America's coal industry to Pennsylvania and West Virginia, completely overlooking-or unaware of- the vast reserves, both those developed and those untapped, situated in the 1.4 million square miles between the Appalachians and the Rockies. At the 1965 AIME Annual Meeting, Hubert E. Risser, Principal Mineral Economist of the Illinois State Geological Survey, presented an interesting picture of the wealth of mineral fuels occurring in that area. In his talk entitled "Trends in Mineral Fuels in the Central United States", Mr. Risser underscored the fact that "more than half of the nation's known reserves of each of the three major fuels-oil, gas and coal-lie within the Central area." The highlights of his speech, with emphasis on the coal situation, are excerpted below.

Jan 6, 1965

By K. Galos

The paper presents increasing importance of mineral secondary and waste raw materials in the minerals management in Poland. Definition of mineral secondary and waste raw materials is proposed, according to current Polish law. On this basis, sources of various types of mineral waste raw materials are analysed. The special attention is paid to the wastes from mining and processing, wastes from power plants, and wastes from steelworks and other smelters. Other types of waste and secondary materials, such as metallic containers, glass containers, batteries, metallic wastes and scraps, are also taken into account. Analysis of sources of such materials is shown together with the main directions of their economic use. Available sources of information on manufacture and use of the mentioned secondary and waste raw materials are also analysed. Finally, for a wide range of waste materials, their current and expected significance as substitutes for some industrial and construction minerals in Poland is given.

Jan 1, 2011

By K. Fleck

Energy West Mining Co. (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, UT. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the in situ coal strength and load transfer mechanisms for improving two-seam designs and support systems.

Jan 1, 2012

By Vaughn Astley, Hassan El-Shall, Ponisseril Somasundaran, Regis Stana, Patrick Zhang

In the past, when phosphate rock quality was good, few paid attention to any of the impurities or other qualities associated with phosphate rock. In general, they had little or no effect on the ability to make the phosphate products for the market. However, as phosphate rock quality declined, it was apparent to the rock consumers that the individual impurities had a significant impact on their processes. FIPR is presently funding an analysis of operating plant data to determine the range of the effects of rock impurities on production plant performance. The study will not be completed until 2002. IMC has agreed to share some of the information they had developed in the early 1990s.

Jan 1, 2002

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

Gold recovery by catalytic copper ammonium thiosulphate solution has been studied. Such a process strategy is very attractive for leaching certain difficult-to-treat ores and presents lessened lixiviant toxicity compared to cyanide. Newmont Gold Company has evaluated the ammonium thiosulphate heap leach process for gold recovery from low-grade carbonaceous sulphidic refractory ores following biooxidation. The ammonium thiosulphate leach process has been studied in laboratory, pilot plant and demonstration scale. Satisfactory test results support the continuation of process development. However, the thiosulphate leach chemistry was found to be very complex. Maximum control of the stability of the leaching system is a key factor for success, especially for the heap leach process. Important solution chemistry is discussed in this paper.

Jan 1, 1997

By Oliver Bowles

ROCK is no doubt the most abundant of all material things because the planet on which we live is made of it. All animal and vegetable organisms and the multitude of natural and manufactured products that occupy a comparatively insignificant film on the outer surface of the planet are derived from rock. Processes of Nature acting for untold centuries have transformed rock into soil, making possible the development of vegetable and annual life; and rocks have supplied the numerous raw materials, metallic and nonmetallic, wherewith the innumerable appurtenances of a complex civilization have been fabricated. As time goes on we live with increasing speed and with enlarged desires. Time and space are shortened by man's ingenuity, and products for human use must be manufactured with greater and greater celerity. It was inevitable that Nature's slow processes of rock alteration should fail to keep pace with human demands and that the variety of natural products should fall far short of the requirements of an industrial age. Man therefore supplemented these processes by attacking rock in its native bed amid using it to supply needs not otherwise satisfied.

Jan 1, 1934

Importance of Strain to Fragment Strength in Blasting Induced Pre-Conditioning When a rock is blasted, cracks propagate through the rock causing the rock to fracture. This paper focuses on applying the results from a series of small scale blasting tests were designed to show the effect that varying blast variables such as explosive type and explosive energy have on the resulting strength of the post blast fragments. It was shown that the velocity of detonation of the explosive product affects the reduction of fragment strength. This has important implications for the downstream comminution process. The observations from these tests are then explained with reference to the principles of fracture mechanics. A simple but effective prediction of blast induced preconditioning is shown.

Sep 13, 2010

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By J. Severin

Surface mining operations are increasingly involving the design and development of deeper and larger open pits, often with plans to transition into underground mass mining operations. Experiences at the Palabora Mine in South Africa demonstrate the complex interactions between underground workings and the steep slopes above that may lead to slope movements that potentially pose safety and economic concerns. To properly assess the rock mass response to these interactions for planning of future developments, understanding the controlling influence of geological and geomechanical structures is crucial. Preliminary results are presented from a detailed review of historical slope monitoring data from the Palabora Mine, before and after the initiation of block caving 400-m beneath a 800-m deep pit. This paper demonstrates that a detailed analysis of geology and monitoring data can be used to better understand the kinematic controls of complex rock slope displacements and interactions between open pits and underground mines. This investigative treatment of the monitoring data is important in understanding the failure mechanisms prior to undertaking sophisticated 3-D numerical models.

May 1, 2009

By Henry Branes

Para maximizar el retorno de la inversión se aplica la economía de escala pero no se consideran el riesgo financiero al aumentar la escala del proyecto. Las curvas de recuperación metalúrgica vs ley de minera no son lineales. Esto implica elegir un punto óptimo, donde los rendimientos decrecientes de la minería selectiva no justifican el aumento del costo de minado y la reducción de la tasa de alimentación a planta. El artículo analiza las variables más significativas y propone una metodología para definir la capacidad de planta óptima para obtener el máximo rendimiento de la inversión basado en la sensibilidad de una serie de escenarios de planes de minado.

Sep 1, 2017

By Elard Miranda, Carlos Lopez

El éxito extractivo en el tratamiento de los minerales auríferos, depende fundamentalmente de su buena caracterización física y metalúrgica, de modo que para un determinado grado de liberación del mineral brinde información acerca de tamaño del elemento valioso y si este se encuentra liberado o incluido en alguna especie mineralógica; del mismo modo debe conocerse el tipo de elemento valioso, si es oro o electrum y los porcentajes de Plata que presenta este último.

Sep 1, 2017

By K. Hakalehto

El uso de métodos modernos en el uso de chimeneas de las minas en Finlandia permite obtener un mejor desarrollo racionalizado de la mecanizado. En ese sentido, el presente texto señala dos métodos seguros y rápidos para la perforación de chimeneas. La perforación para estas chimeneas se desarrolló en rocas duras duras y fuertes en 1972. Asimismo, el costo, itinerario y velocidad son factores a considerar en el empleo de métodos para perforación de chimeneas.

Jan 1, 1982