Search Documents

By Christopher Newman, David Newman

The ability to assess, address, and predict mining-induced stress distribution is paramount in maintaining a safe and efficient underground operation as coal mines continue to develop at deeper depths and in more geologically complex reserves. This is especially true for longwall mining operations given their limited flexibility in panel layout and orientation. This paper focuses on ground behaviors and conditions observed at two deep-cover, steeply dipping longwall mining operations in Utah’s Unita coal basin. This region is susceptible to coal pillar bump/bounce events as a result of high depth of cover, high-extraction mining, and the close proximity of a thick massive stiff sandstone stratum to active mineworks. The successful prediction of mining-induced coal bump events for Mine A and Mine B operating in the Unita basin has prompted mine management to develop a rock mechanics testing database for reserve calculations. The database is applicable to mine planning as well as the development of multiple numerical models to proactively identify and address adverse ground conditions using input parameters calibrated to site-specific behaviors and conditions. For both Mine A and Mine B, the most critical question relates to longwall development and recovery for “extreme” deep-cover longwall panels at overburden depths greater than 600 m. This paper highlights the impact of high-stress concentrations associated with deep-cover longwall mining as well as the methods applied to mitigate stress impacts on miner safety and longwall production.

Jul 1, 2023

Longwall mining in Australia is approaching maturity. Longwall production from 'state of the art' Australian longwall mines now rivals similar US based longwall operations. Regrettably however, Australian gate road development rates in general fall short of the required development to longwall production ratios that are required to sustain annual longwall production capabilities. By contrast, most US based longwall mines achieve the required development to longwall production ratios to sustain their longwalls. This is despite many having to drive three heading longwall panel gate headings to meet regulatory requirements.

Jan 1, 1998

By Downs M

The use of a cutting machine designed to allow simultaneous cutting and setting of roof supports has numerous advantages few development roads in coalmines. The use of such a machine with the added ability to cut a curved roof profile is of considerable interest for longwall development in thick coal.

Jan 1, 1998

By Gregory Hendon

Jim Walter Resources, Inc. (JWR), has successfully longwall mined for many years at depths ranging from 1200'-2500'. However, full pillar extraction has proven difficult and generally economically unfeasible. Overburden and redistributed stresses at these depths require relatively large pillars, which become unmanageable with most pillar extraction practices. The economic benefits of taking gateroad pillars as part of a longwall face have been recognized for some time, including increased life of mine recovery, elimination of belt moves, reduced overcast requirements, and improved longwall to continuous miner ratios. Until recently, the associated risks of pulling pillars prevented any extensive use of this concept at JWR. Due to geological, economic, and longwall repeatability problems, JWR accepted the risks, and undertook pillar extractions with longwall faces in several different applications. The applications included taking a stable pillar (250' wide) as a longwall panel, taking yield pillars on the headgate and tailgate of panels, taking yield pillars and stable pillars in the middle of a panel, mining through chain pillars in the middle of a panel, and taking a support pillar on the tailgate end of a panel. This paper describes the background and experience of pillar extraction with longwalls at JWR.

Jan 1, 1998

By Stanislaw Prusek

The present state of Czech and Polish coal mining industry is presented at the beginning of the article. This paper will inform the reader of the general data concerning hard coal reserves? number of mines, number of miners, output, number of longwalls, productivity, depth of extraction, and extraction methods?in both countries. The main part of the paper describes the methods of gateroad development as well as gateroad support characteristics (support types, gateroad shape and dimensions, distance between support sets, types of reinforcements). The development prospects of gateroad support in the Czech and Polish coal mining industry are also presented.

Jan 1, 2011

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Alcy Dias Rodrigues

O Centro de Operações do Sistema Elétrico da Aperam South América possui um sistema de automação chamado SAE (Sistema de Automação de Energia) para realizar a distribuição e operacionalização da Energia Elétrica na planta em Timóteo, sistema este com mais de 20 anos de implantação. Devido ao alto grau de obsolescência do sistema SAE, a dificuldade de se atualizar todos os componentes do sistema e a complexidade e dificuldade do acesso aos dados, verificou-se a necessidade de encontrar uma forma de disponibilizar os mesmos para os demais sistemas da empresa. Com base nestas necessidades, foi desenvolvido e implantado um GATEWAY capaz de realizar a comunicação com todas UTR’s CORTEX (remotas do sistema), através do protocolo CONITEL 2020, disponibilizando estas informações coletadas em uma camada OPC SERVER para que o sistema PIMS (Sistema de Gerenciamento de Informação da Planta) realize a coleta e armazenamento destas informações, permitindo assim um melhor gerenciamento de energia pelo VIRIDIS (Sistema de Gestão da Eficiência Energética utilizado na APERAM), além de permitir que toda a planta tenha acesso em tempo real às informações de tensão e corrente de todo setor de 13,8 kV, 69 kV e 230 kV.

Oct 30, 2017

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By John Wallace, Chib Iheagwara

"Refinements in sensor design have produced low-cost rugged elements to act as loop coupled with stable detection hardware for eddy current measurement in difficult environments. This has allowed direct dimension gauging of nonferrous and ferrous products above the curie point for absolute dimensions and electrical conductivities independently. The software was developed for the analysis of electrical conductivity profiles in CZ silicon crystal growth, then refined for monitoring bar properties and tube properties. Since in most metal working operations, speeds at the minimum of a few hundred feet per minute are encountered the design of the gauge was optimized for a rapid measurement. Independently extracting electrical conductivity provides data in some metal systems for determining the temperature of the monitored product.IntroductionThe primary reason for the use of eddy currents in gauging is that in hostile environments of metal working techniques such as laser gauging and ultrasonics are not always robust enough for in process measurements. Our goal is to use the technique of eddy current measurement as a quantitative control element in various hot and cold processing operations. Inspection in the early stages of metal and semiconductor processing is usually too costly to introduce in a well developed process and these tools are usually only employed in process development. Until recently there has been no efficient general analysis to allow real time measurements in the cylindrical and the probe geometry that could separate dimensional changes from material property changes both which effect the eddy current response. The basis for these measurements is that forward electromagnetic problem for conductors can be solved exactly for the test geometry which allows an inverse analysis to be made by relaxing the dimensions and conductivity to values which reproduce the measured response[!]. This transformation is based on analysis developed in Robert Siegfried' s thesis and was explored both by modeling and by physical measurement. This analysis was extended over the last few years to allow a more compact data set to be used to exact physical properties. The main result was that the technique would work on high ·quality physical data on as little as three test frequencies with the penalty being that the analysis is computational intensive. The main result of this work was that a quantitative inverse analysis of eddy current response would allow a general instrument to be used for a variety of measurements rather than being tailored for a specific measurement on a specific material test geometry. The development of these instruments has progressed over the last ten years for monitoring real time solidification, crystal growth[2] and hot seamless tube forming where the use of standards in traditional eddy current is limiting. The specific instrument design was dictated by the requirements of the algorithm for both frequency selection and levels of systematic noise that could be tolerated. Because the data is need for real time information this dictated that the system be a parallel multifrequency eddy current instrument feeding the same sensor. The sensor have to be simple and robust and usually a single loop or several loop of heat resistant wire or tube. This presentation is about using inversion of multifrequency eddy current data in real time to produce dimensional and property data on cylindrical conductors and planar conductors in real time. The object of the measurements is to produce dimensional outputs on measurements of conducting material without having to establish a detailed standard for each material or size tested. The dimensional measurements using eddy currents is complicated by material variations in conductivity due to temperature and composition. Those variations that are not geometric are often not of critical interest and complicate the measurement. The dimensional changes are often of more importance"

Jan 1, 1997

By A. W. Hamilton

If you don't know a gauss from a grasshopper, you may be better off than you, think, particularly if you're an ore dressing engineer charged with the responsibility of selecting magnetic equipment for minerals separation and beneficiation. Gauss is a unit of measure for a magnetic field. It indicates the number of imaginary lines of force per square centimeter or per square inch radiating from a magnet. In discussing the strength characteristics of a magnet, we have come to speak of a magnetic field of 800 gauss, for example, meaning 800 lines of force per square centimeter. Gauss became the standard for selecting drum type separators many years ago under an arbitrary set of circumstances. The standard has continued to this day even though magnetics applications engineers have long considered it inadequate. The configurations of the older gauss meter were such that the most accurate and convenient readings on a drum type separator could be made at distances greater than one inch. So, an arbitrary distance of two inches was established and that two inches became the standard. Since then, it has become commonplace to specify magnetic strengths for drum separators according to average gauss readings at two inches; for example 500 gauss average at two inches, 750 gauss average at two inches and so on, even though gauss readings at two inches have much less to do with the separating and beneficiating function of a given application than was formerly believed. The standard was adopted as a means of gauging the strengths of electromagnetic drum type separators, for they were the only ones around at the time. These machines were usually designed with no magnetic considerations other than that the material to be separated should be agitated vigorously and the magnetic fields should be deep and strong. Drums built this way performed well enough, so it seemed logical to measure their magnetic strengths. Hence, gauss at two inches. Now, new improvements in magnetic techniques have made average gauss measurements at 2 inches positively obsolete.

Jan 1, 1971

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By Ron Tluczek

[Power Point Presentation]

Jan 1, 2006

By Kevin DeSomber, Scott Bird

Larger grinding mills continue to utilize large gear-driven drives or electrical wraparound drives. The panel will include presenters from operations with large mechanical and electrical drives. JIM HANDLEY: Before we get to the third and final session, I want to introduce my co-conspirator for this session, John Mansanti. John is manager of milling with Newrnont Gold Company, Carlin, Nevada, and was very active in securing participation in this innovative symposium. I'm Jim Handley and I'm with Cyprus-Amax Minerals at the Sierrita copper and molybdenum mine. Our third presentation is titled "Geared Up or Wrapped Up?" I hear this topic discussed, but never at great length. I think that's because the opinions are fairly strong and diverse, and people generally aren't reinforced properly in their arguments. The first person to enlighten us on this topic is Scott Bird. He has more than 20 years with Kennecott, is a graduate in metallurgical engineering from the University of Utah, and is currently operations superintendent and deals with this phenomenon every day.

Jan 1, 1998

By W. Bassow

In June 1972, when the United Nations convened its historic Conference on the Human Environment, only 24 countries had established government agencies with environmental responsibilities. Of these, 11 were in the industrialized world, 13 in the Third World. By 1985, the number had dramatically surged to a world-wide total of 145, with the greatest growth among the developing countries to 110, an increase of almost 1000%.

Jan 1, 1988

By Peter Grawenhof

In steel mills universal joint shafts, slipper spindles and gear spindles are used to overcome the design- and process- related offset between the axis of the motors and the work rolls. At the roll side the available space for the couplings is limited by the minimum work roll diameter. This leads to extremely high loaded components of the universal couplings especially at the roll side joints. Furthermore modern steel mills continuously strive to roll larger plates and materials with increased strength. This requires drive solutions with even higher torque capacity. For these applications conventional design joints are not sufficient anymore. Even alternative solutions such as hybrid- or offset- designs fall short. Therefore the companies Voith and BUMA Engineering developed together the new GearLink drive concept in close cooperation with the Voestalpine Grobblech GmbH. A completely new combination of universal joints and gear couplings offers an up to now unique solution enabling the use of 1,35- times bigger joint with a 2,5- times higher torque capacity and a 20- times longer lifetime. The GearLink system was first time successfully taken into operation at Voestalpine Grobblech in December 2013 and is up to now working without issue.

Aug 16, 2017

By Ali M. Ghazi, Ronald J. Goble, Lowell S. Whiteside

"Geerite (Cu1.6S) is a rhombohedral copper sulphide which occurs naturally in epitactic replacement of sphalerite; cell dimensions closely approximate those of the host sphalerite.Geerite-type structures can be produced by leaching digenite (Cu1.8S) in ferric sulphate solutions. X -ray diffract ion and electron microprobe studies indicate that eight metastable geeritetype structures can be produced, depending upon the concentration of f erric sulphate solution used and the duration of the each. Although compositions cluster on or near values observed for natural phases, optical properties indicate that we are dealing with polymorphs of these phases. Leaching of chalcocite (CU2Sj in dilute f erric sulphate solutions produces similar results. In contrast, leaching of chalcocite in more concentrated solutions seems to produce true analogues of natural minerals.During froth flotation, sphalerite is activated with a monolayer of floatable copper sulphide with the composition, CuS, of the mineral covellite. However, covellite is not significantly more floatable than sphalerite, and has an incompatible structure because of the presence of covalently-bonded atoms of sulphur. Leaching ofdigenite was used to produce a polymorph of covellite with a geerite-type structure, compatible with that of sphalerite. This polymorph has a flotational behaviour similar to copper-activated sphalerite, suggesting that the monolayer has a geerite-type CuS structure. IntroductionIn an ideal close-packed sulphide structure the distance between sulphur layers, D, is equal to 2R 2/3, where R is the radius of the sulphur atoms. In sulphides with covalently-bonded sulphur layers, such as covellite (Fig. I), D will be an average of the number of covalentl y-bonded and close-packed sulphur layers, weighted as to the relative number of each type of layer. Both D and R are spacings which are readily identifiable structurally and on X-ray diffraction patterns. Goblel has shown that for copper-iron sulphides with metal-to-sulphur ratios between 0 and 2 and copper-to-total metal ratio s between 113 and I there are strong correlations between composition and measured D and R distances (Fig. 2). D can be represented by a single empirical equation relating interlayer spacing to composition; R must be represented by three equations relating the radius of sulphur atoms to composition. One of these equations (R, in Fig. 2) represents ideal close-packed behaviour, the other two represent sulphur radii greater than (R1) or less than (Rh) the ideal."

Jan 1, 1988

By T Hughes

Upward pressure on all mining operations is coming from the triple bottom line. To some extent this is being offset by the rise in mineral prices, but this may or may not continue. The other serious issue facing all companies is the replacement of economic reserves as exploration levels over the past decade continued to decline in line with falling mineral prices. In order to underpin the sustainability of the mining industry it is necessary to continue to reduce cost, reduce the mine environmental footprint, whilst increasing community benefit. At the same time it is imperative that we increase the economic reserves. The highest risk is in adding new mineral discoveries as the strike rate for economic discovery decreases. Gekko Systems Pty Ltd recognises that the most simple and risk averse route to increasing economic reserves is to reduce cut-off grade in the mine, thereby bringing formerly uneconomic reserves into the economic category. We have been developing a new process flow sheet which embodies the triple bottom line and the issue of economic replacement of reserves. This paper describes this flow sheet and presents four examples where this concept is/can be applied to bring about triple bottom line benefits. Sustainability can only be assured if we are the ones in control of our environment, costs and reserves.

Jan 1, 2007

By D. S. Preece, S. Silling, A. Bhuiyan, C. M. Lownds

GEM (Geologic Element Motion) is a Discrete Element Method (DEM) capability for blast-induced heave simulation with a very fast computational algorithm that can efficiently treat many different element shapes by utilizing alternating arcs and lines. GEM calculates rock motion from a knowledge of the gas pressure moving the elements. This requires an expression for the pressure vs volume, or the adiabat, of the explosion product gases. This work uses an analytical expression for the adiabat derived from the explosive’s properties. The effect of the explosive detonation pressure in crushing an annulus of rock, and setting up a shock wave, is termed Brisance. GEM incorporates a working hypothesis for the deleterious effect of Brisance on subsequent rock motion.

Jan 1, 2024

By Stewart A. Silling, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

GEM (Geologic Element Motion) is a Distinct Element Method (DEM) for modeling blast-induced heave. It was developed with a very fast computational algorithm that efficiently treats many different element shapes utilizing alternating arcs and lines to create GEM elements. The GEM computational technique has been previously documented so only a summary will be included in this paper. New features of GEM are the ability to define the size of the rounded corner radius as well the length of the sides for quadrilateral and hexahedral elements. Circles can be created from a quadrilateral element with zero length sides and four arcs. An additional new GEM feature is energy partitioning between brisance and heave. This physics-based partitioning is essential for accurate modeling of blast results over a wide range of rock and explosive types. It accurately defines the volumetric, pressure and energy state of the explosive gases in a blasthole following detonation. Rock mechanical properties and explosive characteristics are included in the calculations. Example simulations provide comparison of the GEM predicted heave for two different classes of explosive. A GEM simulation utilizing hexahedral elements is compared with previous modeling incorporating circular elements.

Feb 6, 2023

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915, Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semi- precious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1975