Search Documents

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By R. Schuhmann, A. M. Gaudin, J. Dasher

Occurrrences of South African uranium have been known qualitatively for over twenty years, but no account was taken of them because of their low grade. In 1945, known uranium deposits were few, but their grades were 20 to 100 times higher than South African ores. Viewed in this light, the exploitation of South Africa's uranium is revolutionary indeed. Development of various analytical procedures capable of dealing with the needs of the project accounted for one-half of the cost and included: a) simple and automatic radiometric analytical procedures, b) sampling procedures appropriate to prevent sample contamination, c) procedures for sample and record-storing to accommodate many thousands of analyses per month, d) chemical methods giving high accuracy analyses for high grade samples not at radioactive equilibrium, and e) development of rapid procedures having moderate accuracy for low grade samples i.e., mill tailings and barren liquors. This task is continuing today with major improvements coming from time to time.

Aug 1, 1956

By James A. Barclay, Ralph C. Kirby

The US minerals posture will be increasingly dominated by three interrelated factors. First, when viewed over the long range, the US supply situation can be expected to steadily deteriorate as demand increases. Domestic high-grade ores have been used up, and other nations compete with the US for world supplies. Second, as environmental awareness becomes more acute, an aroused citizenry is demanding that minerals industries conform their operations to rigorous new standards. Finally, the changing energy situation that confronts the US is forcing an appraisal of energy-use patterns on operations previously guided solely by economic principles and not by national priorities. While future US mineral production and consumption patterns are unclear at this time, it is certain that US demand for minerals will continue to outrun domestic supply. Thus, the US is faced with a challenge of producing more minerals and metals from lower grade resources. Meeting this challenge means a strengthening of US research and development efforts, coupled with their application in the remaining leadtimes available. Some specific examples of how the US Bureau of Mines (USBM) is assisting in the processing of low-grade resources follow.

Jan 6, 1975

By Kot F. v. Unrug

The depletion of thicker coal reserves has resulted in the thinner seams being economically attractive. Surface protection against subsidence limits the extraction ratio to 50% for the room and pillar method as a "no subsidence condition". That rule was developed for pillars with smaller width/height ratio because seams mined at the time were commonly 6 feet thick. Over time pillar ribs deteriorate around the pillar perimeter and thus decrease the area of the pillar. Using 50% extraction as the no subsidence condition in the squat pillar category (below 42 in with w/h > 7) causes unnecessary losses of reserves because squat pillars are stronger. In this paper a method is presented for design of long-term pillars. Based on the analysis of pillar deterioration and field observations, an increase of the "no subsidence" extraction rate to 60% for squat pillars is proposed.

Jan 1, 2001

By Guozhi Lyu, Ting-an ZHANG, Biyu Long, Yajing Tian, Xuejiao Cao, Weiguang Zhang

Aim to the separation problem of high concentration V–Fe in stronger acidic leaching solution of vanadium slag, a novel chelating extraction system is proposed to separate V and Fe. Influence factors including initial pH value, the extractant concentration, the phase ratio, temperature and time are investigated. The experiment results show that single extraction rate of V and Fe reach 85.57 and 0.39% respectively, when pH value is −0.4, organic phase composition is 30% Mextral 973H + 70% sulfonated kerosene oil, O:A = 1:1, stirring time is 10 min, extraction temperature is 30 °C. The industrial experiment results of three levels countercurrent extraction show that the total extraction rate of vanadium and iron can reach 97.44 and 0.23%, separation factor is 6410. The effective separation of V and Fe in high acid and high iron solution can be accomplished.

Mar 1, 2018

By Zuomei Jin

The Mineralogical form of Silver in a Ag-rich complex ore was determined. In the complex sulfide ore, acidic thiourea leaching resulted in 35% extraction of silver directly. In the same complex sulfide ore, under the effect of ultrasonic treatment, 65% of silver can be ex¬tracted. After the above ore had been roasted and acidically leached of Zn and Cu, the silver extracted from this Pb-Ag residue was 96.8%. The effets of temperature, thiourea and ferric ion concentrations and partical size were examined. The leaching rate of silver from the Pb-Ag residue was diffusion controlled. The activation energy was calculated to be 10. 49%KJ/mole. The kinetic model for the thiourea leaching of silver from Pb-Ag residue was obtained and is given by, The kinetics of silver cementation by aluminium in thiourea solutions was also investigated. The activation energy was calculated to be 65. 13KJ/mole, which is reasonable fora rate-limiting surface reaction.

Jan 1, 1995

By Browning E. J

The application of conventional dust control systems in British Coal mines has considerably reduced the incidence of pneumoconiosis. A number of new techniques have been developed involving extraction close to the cutting heads of mining machines which will be capable of controlling airborne dust with the greater intensity of production necessary in the present economic climate.

Jan 1, 1988

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Jin-Young Lee

"Global population is a key factor in future energy requirements, especially considering the important elements of global energy resources, electricity production, the accessibility/non-accessibility of electricity, greenhouse gas emissions and the states of nuclear reactors. Everyday human requirements depend on industrial products, and industries need a considerable amount of electricity to run. Nuclear fuel is inexpensive and bolsters industrial growth. As uranium reserves are being consumed rapidly, an alternative source of energy in the nuclear industry is thorium. Here, primary energy supplies by various sources from 1993 to 2011 as well as estimates of future needs to 2020 are discussed. This study finds that primary energy sources are mainly fossil fuels, renewables sources, and nuclear and hydro energy. In addition, growth depends on increases mainly in renewable sources.Recovery of thorium from its ores by using hydrometallurgical routes were described and discussed. The final part of this paper was presented a case study of the thorium extraction from Korean monazite ore leach liquors by using Prieme JM-T diluted in A150 diluent as an extractant system. And possible separation of the thorium from rare earths (REs) and base metals were calculated by measuring of separation factors and finally, the recovery of thorium from loaded organic of Prieme JM-T was established.THORIUM IS FUTURE NUCLEAR FUEL?Global energy consumption is increasing everyday with the high population growth, high industrialization of numerous countries and the higher level of good and services consumption that follows it. If we look at specific sectors of the economy, oil consumption grew by 0.8 million barrels per day, globally, whereas the increase was 0.4 % for natural gas and coal 1.8 % for nuclear power and just under 2.0 % for hydroelectric power (Asheley 2009). Use of renewable sources of energy for power generation and transportation increased by 3% in 2014 (BP 2015)). Thus alternative source of energy must be identified and developed to meet this increasing demand. Thorium is a potential one for the nuclear industry."

Jan 1, 2016

As the title indicates the central themes discussed in this contribution are sustainable development, information systems, and extractive industry. More specifically, the objective is to present a prototype for the systematic generation of extractive industry (henceforth: EI) û specific sustainability information. The paper begins with the authorÆs viewpoints on the core notions of sustainability, and development, as well as their relationship to information. These set the stage for the introduction of the information system (IS), as well as the follow-up sustainability information system (SIS) extractive industry sustainability information system (EISIS) concepts and related discussions. The paper continues with a second part, in which, efforts to research and develop an EISIS prototype are described. First, the team is presented. Second, the systemÆs aim and target groups are briefly discussed. After, an articulated overarching EISIS conceptual model emphasising capital accumulation, and service flow concepts û is presented. This is followed by a detailed description of the assembled prototype with a focus on data and information generation. The formulation of data generation, storage and transmission processes, as well as its use in sustainability interpretation rules and their embedment in the conceptual model is made with respect to monetised stock and flow parameters, measured in the appropriate dimensions. In the third part, the author presents and discusses the results of a first round of prototype experimental development in three major EI firms. First, the system observation, and data analysis protocols are described. Second, a review of protocol implementation, and respective results, is made. Finally, the overall performance of the proposed prototype, and development process issues are discussed, before suggesting areas for improvement and future research. The paper ends with a conclusion in which the author provides a retrospective balance of the æknowledge creation projectÆ, as well as a prospective outlook for research in this field; before acknowledgements are made and references provided.

Jan 1, 2009

By Theophile S. Yameogo

Les ressources naturelles ont en général été le moteur du développement économique et social des nations. Les pays aujourd?hui développés sont pour la plupart d?anciens eldorado, charbonniers ou pétroliers. D?autres le sont toujours. L?Afrique fait cependant figure d?exception : même en étant comblé de ressources naturelles exceptionnelles, les pays de ce continent croulent sous le poids de la pauvreté et de ses acabits que sont les maladies, la famine, la guerre et l?insurrection sociale. On reconnaît néanmoins qu?il y a des cas particuliers comme le Botswana, la Namibie, l?Afrique du Sud. Face à cette situation, beaucoup de scénarii ont été proposés sans pour autant porté les fruits espérés. Le rapport Brundtland suggère que le développement durable est la clé du succès car elle veille à la prospérité économique, à l?équité dans la société et à la pérennité dans l?environnement. Pour l?Afrique, beaucoup de facteurs doivent être considérés et les solutions se doivent d?être pratiques et éthiques. Le futur ingénieur des mines qui a écrit ce rapport, apporte sa vision de la situation non sans avoir auparavant analysé les faits. Cette démarche, qui se veut avant tout éthique, inclut les aspects sociaux, économiques et politiques. Introduction In the 40s, 50s and the 60s, many economists, among which Harold Hotelling from South Carolina University, thought that developing countries could reach socio-economical success by extracting their natural resources such as oil and minerals. The current economical disaster seems to have contradicted that belief and critics like Davis Graham (Colorado School of Mines) and Michael Ross (University of California at Los Angeles) even suggested that extractive activities stop in Africa. But the experts of the World Bank (Mining Department) and some mining and oil companies are committed to reverse the tendency by implementing a new approach. Considering the principles of sustainable development defined in the Brundtland report (1987), we decided to analyze the possibility of giving the extractive industry a catalytic role in creating a socially, economically and environmentally development in Africa. In other words, can we continue to mine and extract oil in Africa for its blossoming future under the ruling of the sustainable development? In the following, we start by explaining the African socio-economic and political context. After a brief definition of the sustainable development, we explain why, for Africa, some believe in the extractive industry and some don?t. In the end, we draw out conciliatory arguments.

Apr 1, 2005

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days' production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

Established as a Division November 17, 1948 B W Gonser, Chairman J C Kinnear, Jr, Past Chairman H H Kellogg, Chairman-Elect R C Cole, Vice-Chairman, '58 A E Lee, Jr, Vice-Chairman, '59 W R Opie, Vice-Chairman, '60 R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y

Jan 1, 1957

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By Robert D. Pehlke, Kazuhisa Okajima

ThE prediction of the activity coefficient for a solute in a multicomponent liquid metallic solution based on measurements in the related binary systems has been the object of study for some time, particularly in iron-base alloys.1,2 Very few measurements, however, have been made on nonferrous systems; furthermore, measurements made for the specific purpose of testing various prediction equations are almost nonexistent. The measurements here described of the activity coefficient of cadmium in liquid lead alloys were directed toward this goal. One of the most direct means by which the activity coefficient can be calculated has been based on the independent influences of each solute. When solute metals i,j, k, and so forth are present, the activity coefficient, y, of one of these (i for example) may be expressed as a product of factors which represent the effects of each of the other components:

Jan 1, 1964

By H. H. Kellogg

Available high-fernperatzwe equilibrium measurements and other thermochernical data have been critically reciewed for sulfation reactions of the type: Recommended values for log K and ?Fo as junctions of temperature are given for thirty-six suck reactions involving twenty-six different metals. Methods of calculation and choice between conflict-ing data are discussed. SELECTIVE sulfation now enjoys a considerable renaissance as a metallurgical unit process due, in large part, to the available of the fluid-bed re- actor—a device capable of the close control of temperature and gas composition necessary for a successful sulfation process. An additional need, however, if sulfation chemistry is to be approached in a scientific manner, is a reliable body of data on the equilibrium and kinetics of sulfation reactions in simple and complex systems. This paper offers a critical review and compilation of equilibrium data on pure sulfates (simple systems). The last such review, by K. K. Kelley in 1935:30 has proven itself most useful, but the existence of many new data makes necessary a re-evaluation of the available information. METHODS OF CALCULATION For a simple sulfation reaction such as MS04(c) = MO(c) + SO3 [1] there are two approaches one may take toward establishing the value of ?Fo or K as a function of

Jan 1, 1964

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By R. G. Ward, A. E. El-Mehairy

A technique was developed to calculate the density of liquid metals from the profile of a weighed levitated drop obtained by emitted light photography and calibration. The density of liquid copper was determined over the temperature range 1370" to 2100°K and expressed with the equation: The molar volumes and thermal coefficients of expansion are calculated. Copper, upon melting, was found to expand 3.34 pct. A knowledge of the density of liquid metals is essential as it is a parameter appearing in most theories of the liquid state. The liquid density is also necessary for the calculation of the commercially important contraction occurring on solidification. Unfortunately good density values are rarely available and the present work was undertaken to establish a new method of density determination free from the limitations of the existing methods. For liquid metals with high melting points, the variation and the limited number of density values reported in the literature have been caused primarily by difficulties in technique, a matter which has been adequately discussed by Urbain.' In all the methods used for measuring the density of the high-melting liquid metals there are sources of error, and corrections have to be made. For example, in the method of balanced columns, the formation of gas bubbles in one or both arms was a great source of error. In the pyknometer3 and immersed-sinker methods, corrections of certain volumes for thermal expansion to the operating temperature exceed 4 pct. In the maximum-bubble method5 a correction for the thermal expansion of the bubble-tube is used (about 1.6 pct); a second correction takes into account the change in the volume of liquid displaced by the bubble-tube (about 3.5 pct). Another method used is based on the shape of a drop of liquid, at rest on an inert refractory plaque, obtained photographically or radiographi-cally. The volume is calculated from the shape, which is sensitive to the surface tension and supporting material, by some intricate empirical relation. The drop contour changes with 90 deg rotation of the support.7 The application of all methods is limited by reaction between liquid metal and the apparatus. The successful stabilization of a mass of liquid metal during levitation melting8 afforded a technique for measuring the density of liquid metals out of contact with solid materials. The technique was developed by using copper as the density of liquid copper has already been studied extensively, thus allowing comparison with the new method. It consists of calculating the volume from the dimensioned profile of the levitated drop obtained by emitted-light photography and careful calibration. The molten egg-shaped drop spins around the magnetic axis of the coil (lined vertically) at a speed which seems to increase with increasing temperature. The method does not involve corrections and the experimental setup allows the use of vacuum or special atmospheres. The maximum operating temperature is limited by excessive evaporation of metal from the droplet. EXPERIMENTAL Levitating System. A stabilizing ring was used in conjunction with a 3-turn levitating coil energized by a 450-kc per sec, 10-kw Toccotron with a high current-low voltage output stabilized to f 1 pet.' APyrex glass tube with a Pyrex Optical flat window inserted through the coil and ring allowed the use of special atmospheres during levitation melting, as shown in Fig. 1. Optical System. Fig. 1 shows the optical arrangement used to photograph the profiles of the drop, parallel and perpendicular to the vertical spinning axis, simultaneously on the same frame of a high-speed 35-mm film. The optical system was adjusted to avoid any distortion of the profiles and to ensure that both profiles are in focus. The length of path from object to objective was about 30 cm, and a magnification factor close to 1 was obtained with the single-lens reflex-camera system. Temperature Measurement and Control. In operation, the specimen temperature was constant to 5 C for a fixed power input to the levitating coil and fixed rate of gas flow through the tube. The temperature was measured by an automatic two-color pyrometer (Coloratio) checked at the melting

Jan 1, 1963

By P. W. Bennett, E. M. Elkin

A new technique for the recovery of palladium and platinum and sludge from go12 electrolyte eliminates many of the drawbacks of the zinc-dust cementation process. In the electrolytic refining of gold by the Wohwill method, the electrolyte contains about 100 gpl gold as AuCl, and 100 gpl free hydrochloric acid. Any palladium and platinum contained in impure gold dissolve and accumulate in the electrolyte. When their concentration approaches that of gold, it becomes desirable to discard the electrolyte and to recover the gold and the palladium and platinum. As practiced at Canadian Copper Refiners until recently, discarded electrolyte was treated with sulfur dioxide to precipitate the gold. 2AuCl3 + 6H2O + 3SO2 —2Au + 6HC1 + 3H2SO4 The gold precipitate was filtered off, washed with water, and melted with scrap anodes. The wash water was added to the gold-free filtrate and treated with zinc dust to cement the palladium and platinum. PdCl2 + Zn — Pd + ZnCl2 PtCl4 + 2Zn—Pt + 2ZnCl2 The precipitate was separated and sold as Pd-Pt concentrate, and the barren filtrate and wash water were discarded. The receipts of palladium and platinum at this company were too small to warrant their refining. The process suffered from a number of disadvantages. Handling the gold-free solution was disagreeable, as it was laden with sulfur dioxide even after blowing with air overnight. Subsequent treatment with zinc dust was also troublesome. A large excess of zinc dust was required. Spray, acid mist, and vigorous evolution of hydrogen accompanied the reaction. The Pd-Pt precipitate was grossly contaminated with occluded unreacted zinc and with yellow granules of sulfur, thought to be formed by the reduction of sulfur dioxide and its derivatives. Repeated boiling of the precipitate with hydrochloric acid and washing with water decreased somewhat, but did not eliminate, the zinc. After drying overnight, the precipitate hardened to a clinkerlike mass that was difficult to grind. Grinding, handling, and packing created heavy dusting. Even weighing in an analytical balance generated dust, indicating that the powder was easily charged with static electricity. The total palladium and platinum content of the powder varied from 56 to 72 pct, with an average of 65 pct. The powder dissolved in aqua regia with difficulty, leaving a small amount of insoluble residue. However, the main drawback of the process was the strongly hygroscopic Pd-Pt product. The powder showed a marked though erratic increase in weight and a corresponding decrease in assay on exposure to air, even during the course of laboratory analysis. Such changes were the source of disagreement between Canadian Copper Refiners and the buyers of concentrate. The cause of the change in weight is believed to be hydrogen, liberated by the action of zinc dust on hydrochloric acid. Some of this hydrogen was adsorbed so strongly by the precipitate that it could not be driven off during the drying. On exposure to air it oxidized catalytically, forming water. Experiments soon showed that the entire process of treatment of discarded electrolyte then in use would have to be changed. A small quantity of apparatus was moved into the gold room, and experimentation was held to a minimum compatible with the development of a new process. PALLADIUM AND PLATINUM PRECIPITATION It was thought that zinc could be replaced with a reagent other than a hydrogen-evolving metal. Semiquantitative experiments showed that platinum and palladium could be precipitated completely from the gold-free solutions with such well-known reagents as sodium formate, formic acid, formaldehyde, and paraformaldehyde. Sodium formate was the preferred reagent, since the other three are volatile and somewhat toxic. The gold-free solutions used were those saturated with sulfur dioxide, partly freed of sulfur dioxide by aerating overnight, completely freed by boiling, as well as strongly and weakly acidic, neutral, and alkaline solutions. The reactions are complex and can be represented by these over-all equations: PdC1, + HCOONa — Pd + NaCl + HC1 + Co2 PtCl4 + 2HCOONa — Pt + 2NaCl + 2HC1 + 2CCX, Strongly acidic solutions required as much as five times the theoretical amount of sodium formate as did solutions neutralized to pH 4.5. Increasing the pH decreased the consumption of

Jan 1, 1965

By G. R. Rigby

Used basic brick taken from copper anode furnaces, reverberatory furnace roofs, md copper converters have been examined by chemical analysis, petro-graphical examination, and X-ray diffraction tech-niques. In the anode furnace roof, brick absorb copper and copper oxides, whilst in the reverberatory roof, iron oxide with smaller amounts of alumina and silica are absorbed. Chemical reactions in the converter are most complex since the brick absorb both a copper-copper oxide slag and a fayalite-magnetite slag. CHANGES taking place in basic brick after use in copper smelting furnaces have received attention from C. Burton Clark and J. Spotts Mc Dowell,' who examined brick taken from copper converters, and by G. R. Rigby and B. G. Hamilton' who examined brick from copper anode furnaces. This paper describes the changes taking place in basic brick from all types of copper smelting furnaces and discusses the major reasons for lining wear. A) METHODS OF EXAMINING SAMPLES A variety of used brick have been taken from the following positions in various furnaces, a) roofs, reverberatory arches, and bottoms of copper anode furnaces, b) roofs of copper reverberatory furnaces and c) the tuyere line and end walls of copper converters. The method of examination was standard in that brick were first measured and the extent of wear-back computed. They were next sawn in two by a central cut vei-tical to the working face to enable the freshly cut surfaces to reveal any zonal changes and cracks, both of which usually ran parallel to the working face. Each well-defined zone was then sampled for a) chemical analyses, b) petrographical studies using transmitted and reflected light techniques under the microscope, and c) X-ray diffraction studies on powdered samples. From the data accumulated, changes taking place in a variety of

Jan 1, 1962