Search Documents

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By Kritika Baxla, M. Mustafa Kahraman, Frank A. Drews, Yaxue Wang, Joel M. Haight, Kody Powell, Mohit Sobalkar, W. Pratt Rogers

In the opinion of these authors, technology alone can never give an organization an edge over competitors or provide an industry step change. However, history has shown that technology applied with correct logistics and strategy makes a significant difference. Never has the minerals industry faced such daunting challenges and been in such need of a step change. Application of autonomous systems has been steadily increasing in the minerals industry. Automation technology has changed the mining value chain from exploration to mineral processing and refining. The future state will only see additional in-roads of automation into more processes and the whole system design. To better understand the near-future potential of automation, it is useful to explore and review the current state of automation in minerals development. A review of the state of automation research is given. The review will consider three critical areas: automation technology, system’s engineering and management processes around automation, and the role of human factors engineering in automated and semi-automated systems. The review ends with a discussion on the social and political risks of automation in terms of shared value and sustainable development.

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By B. W. Madsen

Experimental results obtained from large scale (7 tons), long-term (500 days) leaching of low tenor copper sulfide ores were interpreted by a geometric model involving the movement of a reaction zone through the ore fragments. The postulated leaching mechanism involved mixed kinetics and included diffusion of the reacting species through the host rock and a chemical reaction at the surface of the mineral particles. Ore properties which were considered were ore particle size and shape, grade of ore, and mineral content. Excellent agreement between the mixed kinetic model and the laboratory leaching results was obtained when minus ½ inch ore particles were not included in the leach. Also, a satisfactory prediction of copper recovery from plus ½ inch ore with a different particle size distribution was made; however, it was necessary to modify the shape factor in the model. Predictions of copper recovery from an ore sample which included the minus ½ -inch fine fraction and leaching for 460 days was 56.5 percent, and the recovery from leaching was 47.0 percent. The presence of fines caused channeling and uneven solution distribution and inhibited the leaching rate.

Jan 1, 1974

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By G. L. Brooke

At present, there are two known cobalt deposits in the 48 contiguous states. This paper is a brief description of one of these deposits. It is a Mississippi Valley type deposit, but somewhat atypical in that the metal of greater interest is cobalt as opposed to lead, zinc, and copper. The history and present work are outlined along with a discussion of the geology and mineralogy.

Jan 1, 1981

By Henry P. Ehrlinger

These are exciting times for those of us involved in the discovery, development, beneficiation, sales and end uses of industrial minerals. The known sources of traditional raw materials are rapidly being consumed or covered up with highways and urban developments. We would never knowingly cover up a source of gold, silver, diamonds, or even base metals with a shopping center, but it has been difficult to justify not locating construction atop a limestone, granite, or sand dune deposit. During the last ten or so years most of the users of significant amounts of industrial minerals have established task forces made up of geologists, mining engineers, beneficiation experts, ceramic and refractory scientists, and senior members of their purchasing departments whose duty it is to determine where the raw materials for their particular finished products will come from now and farther down the road, like 20 years from now. Likewise, these same ceramic and refractory scientists are developing new materials which require a never ending change into different raw materials and the traditional materials must be refined by selective mining, exotic beneficiation practices and expensive but necessary post-beneficiation treatments to produce minerals for commercial use that were either theoretical minerals or at best showcase specimens when most of us here today were in school studiously acquiring a vocabulary which included Calcite, Magnesite, Dolomite , Feldspar, (Labradorite had the play of colors the prof could see but which I rarely focused on) Wollastonite, Celestite, Chromite, Olivine, Barite and Lepidolite to name a few.

Jan 1, 1976

By John W. Crawford

The title of the paper which I have been asked to present is somewhat misleading it infers in fact that there is a definite coalbed height below which raps or canopies cannot be applied to electric face equipment. Although this may be so with regard to certain pieces of existing equipment under certain conditions, to date we do not have enough experience to determine this magic number. Therefore MESA is continuing to hold the line on the time frames stipulated in Section 75.1710-1 of the Mandatory Safety Standards - Underground Coal Mines, which at this point in time requires these protective structures in mining heights of 60 inches or more. In order to give you an idea why we are taking such a firm stand on this matter, I believe it is necessary to describe some of the background work that was done prior to promulgation of the regulations and to give a resume of our experience since the requirements have become effective. Initially MESA made field investigations of all underground mines to determine what the state of the art was in the use of cabs and canopies for protecting equip¬ment operators from falls of roof. These studies revealed that the application was basically in its infancy and what progress had been made was due to the impetus of the mine operators themselves. Manufacturers of electric face equip¬ment provided these structures only on the direct order from the mining company and built them to their specifications. In talking to the operators and the miners in mines where cabs or canopies were in use, it was the consensus that these structures did improve safety and that although originally there was some reluctance on the part; of the miners to work in the confines of a cab or canopy, mast would not work without them once they had been adapted to the equipment.

Jan 1, 1975

By Andrew Thomson, Peter Wright

"A section of a London Underground expanded segmental lined tunnel constructed in the 1970’s progressively deteriorated after 2001, with extensive radial joint spalling and mid-segment cracking. As part of the PPP contract Tube Lines Ltd and their partners carried out various analyses of the tunnel, including analysis of laser scans of the tunnel, geotechnical testing through the tunnel walls, geotechnical desk studies, real-time monitoring and even full-scale segment testing. This paper discusses the behaviour of the tunnel lining in this setting, the causes of failure and the lessons that can be learnt from this rare example of a tunnel which was progressively failing in service. It is finally noted that a replacement tunnel lining was installed during night-time possessions and completed in 2015. INTRODUCTION In 2003, Tube Lines Ltd. was established under a Public-Private Partnership (PPP) scheme to provide maintenance services and upgrade projects for London Underground (LU). The Deep Tube Tunnel Knowledge and Inspection Programme comprised the assessment of all tunnels, shafts and other underground structures. This included a number of lengths of tunnel constructed using segmental concrete linings. First used by LU in the 1960s, the savings both in cost and speed of construction led to concrete linings replacing cast iron for new tunnel construction in all but a few cases. During the initial scoping phase of this programme, inspections identified potential issues with the expanded concrete segmental linings on the Jubilee line. The inspections found a number of segments with surface spalling (Figure 1a), which did not appear on the post-construction defect records. These were generally relatively shallow, up to 40mm deep, spread over a wide area of segment. These were different to spalls caused by handling damage, which are typically localised at segment corners. Subsequent inspections over the following years identified an increasing number of segments with these types of spalls as well as an increased incidence of longitudinal mid-segment cracking (Figure 1b). The increasing occurrence of these defects was hypothesised to be caused by tensile stresses developing in the vicinity of the joint."

Jan 1, 2016

By D. P. Gold

Major sources and reserves of Cb/Nb, Ta, REE, Y, Sc, Zr, Hf, Cu, apatite and vermiculite may be concentrated in primary and secondary minerals associated with different stages and depths of emplacement in carbonatite complexes and kindred alkalic intrusive rocks. Exploration targets include: apatite and pyrochlore (Nb) in the plutonic and hypabyssal core and ring-dikes: bastnaesite (REE), strontianite, barite and fluorite in hydrothermal veins and cone-sheets (subvolcanic setting): thortveitite (Sc,Y) and vermiculite in metasomatized aureoles (fenites): high grade eluvial deposits of apatite and pyrochlore, and secondary REE, Nb, Ti. and V-minerals in supergene and weathered zones.

Jan 1, 1991

By D. Van Orden, Y. Kamiya, R. Lee, E. Ilgren

Crocidolite is a well-known causative agent for mesothelioma. However, studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width although this has never been formally confirmed. To date, crocidolite appears to be the only asbestos mineral for which an epidemiological study comparing the risk of mesothelioma in a population exposed to ‘thin’ fibers with another exposed to ‘thick’ fibers of the same species may be carried out. Finnish anthophyllite, South African amosite, and African Transvaal crocidolite can also be classified as thick fibers, and there is a paucity of mesotheliomas in populations exposed to them compared to those exposed to thin Cape crocidolite. No thin occurrences of these minerals are known. Our previous study looked at crocidolite from several sources. The present study considers the amphibole anthophyllite found in many places in the world. This mineral, regardless of source, does not show the same variation in fiber width found with crocidolite from different areas. All anthophyllite fibers that have been mined may be classified as thick and populations exposed show very low levels of mesothelioma. We suggest the most likely explanation is related to the fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By W. R. Hibbard

Emerging from discussions of U.S. energy policy: from the Project Independence Blueprint; from President Ford&apos;s statements to Congress; and from several independent appraisals of the situation; there is a clear objective to achieve an appropriate balance of supply and demand in the near term future (1) by developing more efficient ways of using energy and (2) by extending domestic sources of energy. More specifically, the strategy for achieving this goal has three parts (1) Conservation of energy through greater efficiencies in automobiles, appliances, lighting, heating, and industrial processes. (2) Increased domestic production of oil and gas through new sources such as the outer continental shelf and new efficiencies such as tertiary recovery. (3) Substitution of coal and uranium for oil and gas in utility power plants and industrial heating. The goal of energy research and development is to help achieve these goals and to help minimize the economic, environmental and social impact of our shift from imported energy to domestic sources. The focus of this paper is the implications of the expanded use of coal, and the research and development which may help achieve the above goals in so far as coal is concerned.

Jan 1, 1975

By Warren N. Warhol

The mutual growth of the rare earth industry and the Mountain Pass Operations was no coincidence. It was the commercial availability of rare earths on a scale first made possible by the capacity of the Mountain Pass Operations that spurred research and development efforts toward new applications for rare earths. The first important demand on Mountain Pass was europium oxide for the activation of red phosphor for color television tubes in 1964. Since that time, other rare earths have become even more important, and Molycorp is continuing to supply an ever widening variety of rare earth concentrates and compounds. We enjoy saying that rare earths are not really rare, and that they are not earths, either. Of course, we are talking about the 15 metallic elements with atomic numbers 57-71, called the lanthanides, which occur in nature always together in very similar proportions. Their scarcity can be gauged by the fact that there is more cerium in the earth&apos;s crust than there is tin, and more europium than cadmium. The word "earths" comes from the early chemical term for oxide. The rare earths were discovered as oxides, and the term has persisted.

Jan 1, 1980

By Rosario Lunar, Jesús Martínez-Frías, Egidio Marino, Trinidad Torres, Jose E. Ortiz, Juan A. Martín-Rubí, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

Seamounts, submarine banks, volcanoes and undercurrent channels are prominent geomorphic features that have become an important target for minerals research and exploration with the goal of future exploitation. Polymetallic ferromanganese deposits are common types of mineralization on these settings. Co-rich ferromanganese crusts are important as potential resources of Mn and Co, but also Ti, Ni, Tl, REEs, PGEs, and other metals. Many seamounts and channels along the Atlantic Spanish continental margin are known to hold mineral deposits but are poorly studied. This work presents and briefly describes the most recent activities of the Spanish Geological Survey (IGME) on exploration and investigation of ferromanganese deposits along the Atlantic Spanish continental margin. Different submarine areas from the northwestern margin of the Iberian Peninsula to the west off Canary Islands have been surveyed by geophysical, sampling and underwater observations from 89 to 4000 m water depth. The mineral deposits cover a large diversity of submarine geological and geomorphical features: mud volcanoes and diapirs related to hydrocarbon seeps, seamounts associated with hot spot volcanism, hydrothermal vents in active magmatic volcanoes, structural basement highs and banks or contourite channels. Considering the collected dataset, we present the preliminary results of the study of these mineral deposits, including ferromanganese nodules and crusts and phosphate pavements and nodules, which can be considered as potential sources of raw materials.

Sep 1, 2014

By Naohiro Kurokawa

Isa Limestone Quarry with an annual production capacity of 18 million metric tons is known as the largest limestone deposit in Japan located in the mountainous region about 20 mile northwest of Ube City, Yamaguchi Prefecture, Japan adjacent to Isa Cement Factory to which it belongs, and which constitutes a mainstay of Ube Industries? cement operating division. Isa Cement Factory is equipped with a N.S.P. kiln of capacity of 3 million metric tons per year, which is the largest of its type in the world. Geographically, it is situated in the south- western tip of the Mainland of Japan (Mid City, Yamaguchi Prefecture) and is bordered by the scenic Akiyoshi Karstic Plateau which is world famous for its huge stalactite grotto.

Jan 1, 1982

By Ehsan Moosavi, Kamyar Tolouei, Mehran Gholinejad

The literature defines rockbursts in slightly different ways based on their generation mechanisms, field phenomena, and degree of damage, but in a way that is almost consistent. Generally, a rockburst refers to seismic events that mainly happen in underground excavations, for purposes such as underground mining, road and railway tunnels, nuclear power, etc., and that are followed by the collapse and outburst of rocks. Long-term rockburst prediction can be abstracted as a classification problem mathematically, in which we can introduce deep learning to solve it. Further, using deep learning in rockburst prediction can overcome drawbacks such as subjectivity and inconsistency brought from previous traditional approaches. A rockburst data-set, was employed to evaluate the current method for predicting rockburst grade, and the good results of overall success rate were obtained. The results indicated that the proposed algorithms can speed up parameter optimization search, the proposed method is robust model and might hold a high potential to become a useful tool in rockburst prediction research.

Apr 26, 2022

By Megan Badonie, Devlon Shaver, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Critical minerals are becoming more important in our technological society because they are used in many of our electronic devices, batteries, and magnets. In New Mexico, low to moderate concentrations of critical minerals are found in Late Cretaceous coal and related strata in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, REE, and Critical Minerals) program. The New Mexico coal, humate, and clinker deposits are relatively low in REE (<325 ppm TREE), Li (<90 ppm), V (<168 ppm), Co (<51 ppm), Ni (<108 ppm), Zr (<557 ppm), and many other critical minerals compared to normal economic deposits. Some of these rocks are enriched in Al2O3 (<40%) and Sr (<3740 ppm), both critical minerals. Common minerals hosting the critical minerals in these rocks include clay minerals, zircon, and rutile/anatase. As the demand for some of these elements increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Ultimately, economic potential will most likely depend upon production of more than one commodity, maybe even from coal, humate, and clinker deposits.

Feb 1, 2024

By Steven J. Schatzel, Kayode M. Ajayi, Marcia M. Harris, Zoheir Khademian

Predicting rockmass permeability is critical in evaluating various engineering designs, including estimating gas inflow to a longwall mine in the case of a hypothetical breach in the gas well. This study conducted field permeability measurements to validate a geomechanical model capable of predicting rockmass permeability during longwall mining. A series of slug permeability tests were conducted in an active mine in Pennsylvania. A model of the mine was constructed in 3DEC numerical modeling software, and permeabilities were calculated. The modeling results agreed well with the pre- and post-mining permeability measurements, showing the applicability of this tool to evaluate gas well stability near mine workings.

Feb 1, 2024