Search Documents

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By G. G. Goble

Dynamic pile testing is now over 20 years old as a routinely applied tool for evaluating driven pile installation. The first test on a cast-in-place pile was performed more that 15 years ago. The research that produced the method began almost 30 years ago. But, questions still arise regarding the appropriate use of this technique so some review is useful. Today a number of methods including dynamic testing all depending in some way on the application of dynamics are in routine use. First, Wave Equation analysis can be used to predict pile driveability before going to the field. The same approach can be used during driving to estimate the bearing capacity based on the blow count observed in the field. Dynamic measurements, on the other hand, can only be used after pile driving has begun. They offer predictions of pile capacity as well as measurements of hammer, driving system, and pile driving performance characteristics. The first part of this paper will be devoted to discussing how the foundation engineer can use these tools. First, a brief review of what dynamic methods actually do. In Wave Equation analysis a numerical model of the hammer, driving system, pile, and the soil is created by the engineer. The hammer is dropped on the pile and using a discrete, dynamic analysis the motion of the individual pile elements is calculated as a function of time. Of course, input information must be supplied by the program user to describe the hammer, driving system, pile, and soil. In the current state of development, the primary problem in input data is with the hammer performance (efficiency) and the soil description. Research may be able to do a better job with the soil data, but hammer performance will always vary from hammer to hammer and is dependent on the affectiveness of the inspection process. Prior to beginning pile driving the Wave Equation analysis supplies the best available estimate of what will happen when driving begins. It gives an estimate of blow count during driving, driving stresses, both tension and compression in the pile, and for diesel hammers, stroke. The selection of the driving system can be checked with the results of Wave Equation analysis and modifications can be made if required. For example, if the blow count at the required capacity was deemed excessive by the contractor a larger hammer could be tried or if driving stresses were too high changes could be made in the cushion or the hammer selection could be modified. All of these modifications are possible with only the cost of a computer run. The primary questions regarding the accuracy and reliability of Wave Equation analysis at this time is with regard to the assumptions made to represent the soil characteristics and the difficulty in predicting hammer performance.

Jan 1, 1993

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By R. Bellotti

The theory of cavity expansion in an infinite frictional soil mass whose strength is represented by a curved Mohr-Coulomb failure envelope has been used to predict with some confidence the cone resistance of a clean dry sand. Experimental data were obtained from cone penetration and pressuremeter tests on two sands, conducted in a large calibration chamber (CC) under carefully controlled placement and boundary conditions. A plane strain bearing capacity theory was developed, and to convert the results to axi-symmetric conditions, an empirical "shape factor" was used. In the paper, the theoretical background, experimental data, calculation procedure, and the results of the analysis are presented. In general, a reasonable validation of the cavity expansion approach to the bearing capacity of deep foundations has been obtained.

Jan 1, 1987

By W. H. Liu

The stability of floors of large drydocks and wagon tipper sheds at coal terminals is an important matter but quite difficult to solve. Anchors can be used to join floors to foundations thus ensuring the stability of floors by the self-weight of floors and the pull of anchors. In this paper, the author describes the structures and types of the anchors used in the floors of the drydock in Beihai Shipyard and the wagon tipper shed at Shijiu Port, both in Shandong Province China, the determination of bearing capacity of anchors in rock bed of highly weathered granite, the comparison between prestressed anchors and non-prestressed anchors, the construction technology of anchors and the analysis of field experimental data.

Jan 1, 2010

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects. Both specimens were constructed with pile diameters of d = 0.61m (2 ft), fixed head boundary conditions, and placed in stiff clayey soil at a test site near the LAX Airport in Southern California. Internal instrumentation was installed in the single pile as well as in three piles within the pile group to obtain pile curvatures. External instrumentation controlled the lateral displacement of the specimens. A combination of experimentally and analytically obtained p-y curves for the single pile was used to simulate results for piles located in the group when field data were not available. All test specimens were tested to structural failure and excavated after test completion to investigate pile damage and plastic hinge formations. Calculated group interaction factors ranged between 1.0 at very small displacement levels of <2.5 mm (0.1 in), 0.8 at the initiation of the pile-soil-pile interaction, i.e. between 4 mm - 15 mm (0.16-0.6 in), and increased towards 0.9 near structural failure (displacement >25 mm or 1 in). A literature set of p-multipliers was found to reproduce an accurate fit to the available load displacement test data from the group.

Jan 1, 2010

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By Peter O. Wilkinson

Ascot Racecourse in the UK is a major international venue for horseracing. The racecourse is being redeveloped to provide entirely new public facilities. The development includes the construction of a new grandstand. A site investigation was earned out comprising mainly cone penetration testing. The site is underlain by the Bagshot Formation, comprising predominately cohesionless deposits of medium dense becoming dense, silty fine to medium sand, containing occasional layers of clay. Shallow foundations would present uncertainty regarding total and differential movement; hence a piled foundation solution was chosen using a continuous flight auger (CFA) piling system. The possibility that piles may found either directly on or within the influence of cohesive material suggested uncertainty regarding toe resistance. In order to measure shaft friction, an instrumented preliminary test pile was undertaken. The results were compared to published correlations of cone and shaft resistance. This approach resulted in a net saving in terms of pile length which resulted in optimum value engineering and hence a cost saving to the client.

Jan 1, 2006

By Jogeshwar P. Singh, Ahmed AlaaEldin, Mohamed Ashour

The presented methodology allows the determination of the response of laterally loaded battered long piles in sandy soils based on the soil-pile interaction. The Strain Wedge (SW) model which was originally developed for laterally loaded vertical piles is modified to assess the behavior of laterally loaded battered piles with the consideration of soil and pile properties. The method predicts the pile-head response and associated p-y curves. The presented soil-pile model accounts for the variation of the direction and magnitude of the batter angles from the vertical position. Unlike current practice, the proposed technique also provides the p-y curves for battered piles in sandy soils based on soil and pile properties (i.e., sand relative density, friction angle, pile geometry, etc.). The proposed methodology has been validated through a number of comparisons with full/model-scale pile load tests. INTRODUCTION The influence of pile battering on the lateral response of piles is rarely studied in the literature. Over the last decades and as suggested by Kubo (1962) and Zhang et al. (1999), a p-y multiplier is applied to predict the response of laterally loaded battered piles from an equivalent vertical one. Several researchers conducted model-scale piles load tests to understand the behavior of battered piles subjected to lateral load (Juvekar and Pise 2008; Meyerhof and Ranjan 1973; Meyerhof and Yalcin 1994). However, such tests were conducted on model piles with diameters less than 30 mm which may not have reflected actual soil-pile interaction. Battered piles are generally categorized as positive or negative battered piles according to the angle of pile installation as shown in Fig. 1. From the small-scaled and numerical models of battered piles, it was found that the lateral capacity of negative battered piles is larger than that of vertical ones. On the other hand, the positive battered piles have lower lateral capacity when compared to vertical piles (Fan-ren and Ji-Ming 2011; Juvekar and Pise 2008; Manoppo 2010; Reese et al. 2004; and Reese and Van Impe 2011).

Jan 1, 2018

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By Zhou Lu-Jian

The Port of Shekou is situated at Shenzhen Bay on the east bank of Lingding Ocean. Its coastline is about 6 km long and the water depth near the shore is Favourable. Across the bay is the &apos; New Territories " of Hong Kong. The port is at a distance of 22-23 seamilesaway from center of Hong Kong and 80 seamiles to Huangpu Harbour of Guangzhou, its highway links with Shen-Guang Highay. Since 19 79 China Merchants Group of the Transportation Department, began to set up Shekou Industrial Zone, the port has been developing and flouri­shing in business. With 15 large or small berths in all, the present portline is 2600 m, and the annual cargo throughout is over 3,000,000 tons and the annual passenger traffic is about 2,000,000 persons. Equalling a medium-scale seaport, it has been officially approved as an oceangoing transit port by the ministry of Transportation. The construction of Shekou port is chara-terized by the self-collected funds and the short construction period. In view of this, the optional plan of the port structure must serve the requirements of simplicity in struture, economy in mate­rial and speed in construction. That accounts for the most application of the sheet piling type to the port in Shekou. Once the project was approved, the cons­truction started. Only within an average period of 7-8 months, a deep water pier was completed and put into operation, which covered series of processes from exploration, designing, tender for con­struction to completion.

Jan 1, 1991

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By Adriaan van Seters

"Abstract The content of Eurocode 7 – Part 1 and Part 2 – with respect to piled foundations is outlined. The important role of pile testing is presented and the derivation of the characteristic value of pile bearing resistance is explained. Recommendations for the use of correlation factors are given. The ongoing work of the Evolution Groups on piling is to prepare a revision of Eurocode 7 after 2019. Future topics and changes are highlighted.General outline of pile design by Eurocode 7In his paper for this conference Frank (2014) outlined the various aspects of standardisation for pile foundations, which involves Eurocode 7 as leading for pile construction in Europe. Standards for pile testing and execution of piling works were established in the last 15 years.This paper focuses on the design of piled foundations according to the design code Eurocode 7, which consists of 2 parts:EN 1997-1 Geotechnical design - Part 1: General Rules (CEN, 2004);EN 1997-2 Geotechnical design – Part 2: Ground investigation and testing (CEN, 2007) In Eurocode 7-1, Section 7 – Pile Foundations - deals with the design of piles. The safety concept for pile design is given in Section 2 – Basis of Geotechnical Design - for the three Design Approaches.In Section 7 presents the design of piles according to four methods:1. Results of static load tests2. Empirical or analytical calculation methods3. Results of dynamic load tests4. Observed performance of a comparable pile foundation.Guidelines for the ground investigation for piles is provided in Eurocode 7-2, Annex B.3. In the Annexes of Eurocode 7-2 examples of analytical methods to determine the bearing resistance of a single pile based on the results of various ground investigation techniques are given. Thus calculation models are presented based on design using the results of Cone Penetration Tests (D.6 and D.7) and Pressuremeter Tests (E.3). The Annexes of Eurocode 7-2 are informative.For the interpretation of Eurocode 7, reference is made to Frank et al (2004) and Bond and Harris(2008)."

Jan 1, 2014

By Jiwei Duan

The deformation and load transfer behavior of a single soil-cement column are studied with the finite element method. The results show that there is an effective length for a soil-cement column. Beyond this length, the settlement of the column is approximately equal to a constant. The effective pile length is introduced to the concentric cylinder approach (Randolph and Wroth 1978), and an analytical formula for estimating the settlement of a single flexible pile is presented. A second analytical formula for determining the effective pile length of a soil-cement column is obtained and an example shows that the calculated and measured results are in quite good agreement.

Jan 1, 2002