Search Documents

By G H. Reavely, The University of Western Ontario Department of Geology

The lower Middle Devonian Sylvania Sandstone occurs in the sub-surface in the western part of Mal-den township, Essex county, Ontario. The formation is composed of well rounded, frosted quartz grains with a silica content varying from 42 to 93 per cent and the grains are cemented by carbonate, constituting up to 57 per cent of the rock. This sand-stone is not a homogeneous bed but is divided by strata rich in carbon-ate cement. The thickness of the Sylvania in Malden township varies up to a known maximum thickness of 88 feet. The lower contact with the chert-bearing Bois Blanc formation is sharp but the upper contact with the Amherstburg formation (Detroit River group) exists as a transition by a gradual downward increase in quartz grains. The Sylvania would seem to outcrop in the lake bottom near the mouth of the Detroit River dipping to the north along a broad anticline the axis of which follows the Detroit River. Just south of Amherstburg, a local east-west trending

Jan 1, 1961

By Jie Zhu

Coal bumps are a special form of release of geologic strain energy that has already been one of the most dangerous hazards to underground mining safety in China. A number of coal-bump models have been developed to quantify coal failure under assumption that a bump is a kind of non-gas induced outburst. However, some technical experts in charge of micro-seismic and gas monitoring have found unusual gas emissions before and after bump, which suggests that it is possible for gas to trigger coal bumps. Considering the coal reservoir as geological body composed of the coal matrix and gas, a new model based on Lippmann?s bump model is proposed to understand the initiation of coal bumps. The redistribution zone from excavation of a roadway has been calculated and analyzed regarding its relation with mining depth. It is shown that high gas pressure may push the coal seam to overstep the critical state due to extension of the plastic disturbed zone, and this is harmful to the stability of coal seam. This model successfully explains the bump phenomena of the Xinzhouyao mine at shallow depth.

Aug 1, 2013

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

A line of nine self-aspirating W emco cells, part of the Rougher circuit at Division Salvador, Codelco Chile, was retrofitted to allow operation with forced air. Each cell could be operated self-aspirated or with compressed air supplied through a 4-inch line equipped with a mass flow meter. Gas dispersion was characterized for the two modes of operation. Metallurgical performance was compared under self-aspirated conditions and with different gas profiles under forced air conditions. Cell characterization demonstrated that with forced-air the cells could not evenly distribute air across the cell volume. Bubble size increased with gas velocity, as expected, with no difference between self-aspirated and forced-air operation. A systematic increase in bubble size down the bank was found. Cumulative bubble surface area flux down the bank showed no major differences between surveys. However, grade-recovery curves revealed that the highest recoveries were invariably obtained with forced air operation. Plotting concentrate mass recovery vs. enrichment ratio showed that the line performance could be controlled over a wider range when forced air was used.

Jan 1, 2007

By G. Stafford Whitby

N ATURAL gas is found in several provinces of Canada, particularly Ontario, New Brunswick, and Alberta. The largest producer is Alberta, and there the most important field is the Turner Valley, where some low-gravity crude oil and naphtha are associated with the gas. Last year there was produced from the Turner Valley field an average of 3,462 barrels, or about 450 tons, of oil a day. The gas flow from the wells in this field bears such a high ratio to the oil which comes from them that, despite the enforcement of a measure of conservation, it amounted to the vast quantity of 6,000 tons a day, or more than 2,000,000 tons a year. Prior to the application of any conservation measures, the gas flow was at one time of the order of 12,000 tons a day. The heat content of one ton of the gas is almost equal to that of two tons of coal. A certain amount, say, 10 per cent," of the gas is used in Calgary and surrounding towns and in re-pressuring the Bow Island gas field, but the greater part of it goes to waste. What are the possibilities of making use of this waste gas, in whole or part? The possibilities of using it profitably as fuel for domestic and industrial purposes have undoubtedly been carefully considered by the Company which now distributes a part of the gas to cities and towns in Alberta. But the relative sparness of the population and the cost of pipe lines makes such possibilities strictly limited. There are, however, distinct possibilities of making use of at !east a part of the gas for the production of a variety of chemical products and of liquid motor fuel. The present paper is devoted to outlining some of these possibilities. About three-quarters (by weight) of the Turner Valley waste gas consists of methane, the lightest and, chemically speaking, the simplest of hydrocarbon gases. The remaining quarter consists of heavier hydrocarbon gases-ethane, propane, and butane. Formerly, naphtha was separated from the well gas by a simple process of self-refrigeration. The gas coming from the wells at a pressure of, say, 1,200 to 1,800 lb., was passed through simple cylindrical vessels fitted with baffles and known as 'separators'. The pressure was allowed to drop to, say, 300 lb. in the separators, and the cooling effect secured by this expansion brought about separation of the naphtha. The naphtha thus obtained was 'wild', that is, it had a high vapour pressure owing to the presence in it of dissolved and liquefied gas. In order to reduce the vapour pressure to a level at which the naphtha could be shipped, this gas was removed either by distilling it out through a 'stabilizing' column or, according to the practice at many wells, merely by allowing the naphtha to 'weather' in open tanks (heated by coils if necessary) until the gas had been driven off in to the air.

Jan 1, 1936

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By Maurice Morton

THE use of organic and inorganic stains has found wide application as a means of detection and estimation of organic fibres. Such stains have enabled the analyst to distinguish between organic fibres of different type and even between wood fibres produced by different processes. Among these stains, aqueous iodine solutions have figured prominently, as in the case of the well-known Sutermeister and Herzberg stains. At the Johns-Manville laboratories, the idea of applying a stain to asbestos fibres was first considered solely as a visual aid in the microscopic examination of such fibres. The staining medium used in this work consisted of a 1 per cent solution of iodine in C.P. glycerine, the latter being used extensively here as a dispersing and mounting liquid for asbestos fibre. This iodine solution was found to have distinct staining properties when used on the local chrysotile fibres, and to improve greatly their visibility under the microscope. It was soon revealed, however, that this staining is apparently limited to the chrysotile variety of asbestos, as against other varieties. It can be readily seen that, if such were the case, the staining test would become a very useful tool in differentiating between chrysotile fibre and the other mineral fibres, without recourse to a lengthy chemical analysis. Hence this investigation was launched, with the purpose of obtaining more information as to the selectivity of this stain as well as its mechanism. The only previous work of this nature that could be found in the literature was that of Van Winsen and Graham (1, 2, 3) on the adsorption of erioviolet dye by serpentine and related magnesia minerals. However, these authors did not refer to any specific behaviour of chrysotile as against other types of asbestos fibre.

Jan 1, 1941

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By A. O. Dufresne

A Step which, it is believed, will prove extremely beneficial to the Quebec asbestos-mining industry was taken during 1931, when the asbestos mine operators of the Province assembled to work out a uniform method of naming the products of their mines. The outcome of several meetings was the drawing-up of a classification which defined, limited, and designated anew the numerous grades of asbestos marketed. It entailed no drastic departure from the existing processes of grading, nor any revolutionary changes in methods of testing, but aimed rather to perfect existing methods. The classification proposed has been accepted by all operators in the Province, who, from January first of this year, began introducing the new nomenclature. Unless one is conversant with the properties and mode of occurrence of chrysotile asbestos, with the unique milling methods devised for its recovery, and with the history of the development of their technique, he may not readily understand the basis of the new classification. For information on these and other data concerning the industry, the reader is referred to a recent publication, Chrysotile Asbestos in (Canada, by James Gordon Ross, issued by the Mines. Branch of the Department of Mines, Ottawa. The object of this paper is to present briefly some of the phases in the evolution of the classification of Canadian chrysotile asbestos, in the hope that the recent effort to standardize the marketable products of one of Canada's most important non-metallic mineral industries will open a field for discussion, fruitful in new ideas and constructive suggestions. The necessity for the grading of asbestos results fundamentally from the fact that the price per ton depends on the length of fibre. At all times in the history of the industry, the very limited available supply of the longer grades, as well as the requirements of the trade, have caused relatively very high prices to be paid for fibre over half an inch in length, while for the shorter grades the price decreases rapidly, and at a rate which bears no proportionate relation to the length of fibre.

Jan 1, 1932

By J. Zollinger, J. R. Kennedy, J. H. Park, D. Daloz

"In order to improve the properties of cast Ti-Al alloys to replace Ni-based superalloys past the low pressure stages of aircraft engines investigations into inoculation for grain refinement were carried out. Previous work showed isomorphic self-inoculation using Ti-Al-Nb particles was effective for grain refinement, however the relatively fast diffusion of Nb in Ti-Al make it difficult to observe the mechanism of nucleation. An alternative alloy was developed in the Ti-Ta system for isomorphic self-inoculation, maximizing the Ta content to improve the particles survivability in the melt. The powder processing produced comparatively small inoculant particles which dissolved, however larger particles were seen to survive solidification. The density difference between the inoculant particles and melt resulted in an inhomogeneous mixing of the particles and the melt with larger particles found near the outer edges of the ingots. Variations on particle size and interaction time between the inoculants and the melt resulted in the Ti-Ta inoculant reducing the as-cast equiaxed grain size by a factor of two compared to non-inoculated samples as well as increasing the equiaxed fraction in the ingot.INTRODUCTION Lightweight metals are of particular interest in aerospace applications. The hot sections of turbines are dominated by blades made of nickel based superalloys. Recently the GEnx turbine introduced TiAl blades in the last low pressure stage of the turbine to reduce weight and improve fuel efficiency (Kim & Dimiduk, 1991). In order to carry these benefits deeper into the turbine the high temperature (>800oC) properties of the alloys must be improved. Current grain refinement methods to improve properties rely on boron additions which may not be applicable for all blades as brittle precipitates may be formed during processing (McCullough, Levi, Mehrabian, & Hyman, 1991). A novel grain refinement process was previously introduced called “isomorphic self-inoculation” using Ti-Al-Nb particles to successfully grain refine TiAl (Kennedy, Zollinger, Bouzy, & Daloz, 2016). In order to better understand the mechanism of this process an investigation was carried out using the same process but with a Ti-Ta alloy which is more stable in the TiAl melt than the Ti-Al-Nb."

Jan 1, 2017

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By A. Vasenev

The quality and durability of asphalted roads strongly depends on the final step in the road construction process; the profiling and compaction of the fresh spread asphalt. During compaction machine operators continuously make decisions on how to proceed with the compaction accounting for project specific aspects as: ambient conditions, road geometry, roller type, asphalt mixture characteristics and behavior of other machines. In discussions over quality improvement in road construction it is often suggested to robotize rollers. To operate such robots would of course require operational strategies and routines. The reality of this moment is that these operational strategies and routines are not documented. To identify the existing best working practices and, ultimately, to proceed with developing automated robotized compactors, the knowledge of machine operators should at first be explored and described in a formalized way. Unfortunately operators have difficulty verbalizing their expertise. Observation of behavior, as machine movement patterns, could be helpful to extract the operational strategies, but such observations are time and labor consuming. To overcome this burden we developed a Virtual Reality (VR) environment. In this VR environment operators perform compaction virtually, and their operational choices are traced and analysed. This paper describes this VR development and explains how it helps in following machine operators and extracting their (tacit) professional knowledge. The road geometry and the working conditions are visually represented; the operators show - rather than explain - how they would proceed with the compaction process in the given conditions. Movements of virtual machines are documented, analysed, visualised and discussed. This VR approach is expected to contribute to learning, to more formal description of operational strategies; stepping stones towards compaction algorithms for roller robotisation.

Aug 1, 2013

"Decreasing gold-in-ore grades is one of the main drivers of poorer productivity and rapidly escalating unit costs. Grinding costs, water use and reagent consumption are all intimately related to the ore grade processed. Various pre-concentration technologies have been developed that can be applied at various stages of crushing prior to ore grinding. This paper will review the amenability of ores to coarse particle barren gangue rejection for fine crush sizes in the pumpable particle size range (i.e., particles between 5 mm and 0.3 mm in size). The liberation of oxide gangue achieved during crushing is evaluated by proxy using sink-float analysis and the deportments of gold, sulfur, and arsenic into sinks and floats are monitored. Amenability of gangue rejection by continuous gravity separation is evaluated after various crushing modes (vertical shaft impact crushing, cone crushing, and HPGR crushing). The potential to identify coarse particle mineral association and liberation using three-dimensional x-ray computed tomography will be discussed.INTRODUCTIONThe aim of research in this area is to explore some of the attributes which make some ores amenable to preconcentration, or rejection of a significant component of the feed mass to tailings at a coarse liberation size. Characteristics such as ore type, mineralogy, breakage pattern, particle shape, and liberation characteristics may need to be examined to identify amenability to pre-concentration amenability.It is intended to focus on continuous gangue rejection in the pumpable size range (0.3–5.0 mm) as this remains one of the key opportunities to reduce processing costs through a combination of techniques including screening (for mineral differentiation rather than size classification only) and gravity separation (using jigs). This is to be contrasted to conventional preconcentration as performed with automatic ore sorters."

Jan 1, 2016

By Ki-Bok Min, Seokwon Jeon, Seung-Beum Choi, Taehyun Kim

"In order to investigate anisotropic characteristics of Boryeong shale in Korea, which clearly shows transverse isotropy, a series of experimental tests were carried out. Using Brazilian test, five elastic constants and tensile strength of the shale were evaluated. Elastic constants were determined by iterative procedure and in order to perform this procedure, constitutive model was modified to fit the experimental condition. The anisotropic ratios of elastic constants were evaluated and the applicability of the methodology was assessed. Apparent Brazilian tensile strength profile was investigated and the ratio of the maximum to minimum tensile strength was estimated. Results showed that the tested rock type had low to moderate anisotropic characteristics.INTRODUCTIONMechanical, thermal and hydraulic characteristics of many rocks vary according to direction, which is known as inherent anisotropy, and it is originated from stratified and/or foliated structure of intact rock and discontinuity of rock mass. Anisotropy is one of the long standing issues of rock mechanics field and it has to be taken into account in several engineering fields such as civil, mining and petroleum engineering. An anisotropic medium has 21 independent elastic constants without any assumption of symmetry. If a material has any symmetry, the number of elastic constants required to define its behavior reduces and eventually two constants are necessary if it has complete symmetry, which is known as isotropy. An anisotropic medium that has remarkable planar structure due to its stratification and foliation such as bedding is often called as a transversely isotropic medium. Transversely isotropic model is frequently adopted in many applications especially for sedimentary rock formation and five elastic constants are required to establish the constitutive model."

Jan 1, 2015

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By Z. Farhat

In spite of advances in cutting tool technology, the understanding of the basic wear behavior and failure mechanisms needs further study. Tool wear is the main factor contributing to geometrical error and thermal damage in machined components. Manifested as a reduction in tool life, it also affects the workpiece surface finish, increases cutting forces and induces residual stresses. Furthermore, the emergence of high and ultra-high speed machining processes necessitates the investigation of tool wear under these severe working conditions. Tungsten carbide-cobalt composite material has been used traditionally as wear resistant materials for many years. One main application of this material is in cutting tools. WC-Co tools consist of hard WC particles imbedded in a tough Co matrix, which functions as a binder phase. More recently, Cubic boron nitride (CBN) tool material have attracted special attention due to its high hardness and excellent wear resistance. Boron nitride in its cubic form is known to be the hardest material next only to diamond. In this paper microstructural and tribological properties of commercial grade WC-Co and CBN cutting tool materials are investigated under high speed cutting conditions. The CBN cutting tools were found to be superior to tungsten carbide (WC) tools. Four-fold increase in productivity and significant reduction in chipping and cratering was achieved for CBN as compared to WC. Wear mechanisms are proposed and are related to the observed wear characteristics in the cutting zone.

Jan 1, 2006