Search Documents

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By D Kent

The introduction of digital technologies into the underground mining industry, in both coal and hard rock mining, has enabled many high bandwidth applications to be adopted by mines.Digital networks based on 802.11 b/g/n open Wi-Fi standards allow for many applications to be run over a single communication backbone. One important application has been tracking personnel and equipment via RFID tags. This tracking application has in turn formed the basis of a Proximity Detection System (PDS) or Collision Avoidance Systems (CAS). The paper discusses the growth in digital technology as the communication backbone in underground mines which has allowed the ‘convergence of technologies’ that has been occurring in the general business world to be available to underground mine operators. Then the paper will focus on the use of the technology in the increasingly important are of risk control around mobile plant underground. The specific use of digital devices for proximity detection, in both hard rock and coal mines, to provide a system that can deliver an additional level of control to the risks associated with people-vehicle interactions underground is discussed. The initial implementation of PDS in the hard rock mining environment is based on two zones of detection, required for large and relatively high speed vehicles. Information will include:•the principles of the underlying technology,•installation learnings and effectiveness, and•change management methodology and issues.The most recent development to integrate Mine Site Technologies (MST) PDS with Frederick Mining Controls’ HazardAvert® System to extend the overall Proximity System’s functionality in hard rock mines and for use in coal mines is overviewed.

Mar 21, 2011

By Cooper W. C, Stokes M. A

Proterozoic gold deposits in the Pine Creek Geosyncline are at present receiving renewed attention with the opening of old mines and several new discoveries. This important polymetallic province contains occurrences of gold, base metals, tin, tungsten, tantalum, platinum, palladium and aluminium. These resources have been exploited over the past century with periods of major interest during the turn of the century and during the past 20 years. Economically viable resources of predominantly gold, eg Pine Creek, Woolwonga, Brocks Creek and Union Reefs, and Ag-Pb-Zn, eg Woodcutters are currently in development or being mined. A variety of genetic models, ranging from magmatic through hydrothermal to syngenetic, have been postulated in the past for the formation of gold deposits in the Pine Creek Geosyncline. The first discussion on the regional geological factors that control ore deposition in the Brocks Creek-Howley District was by Sullivan and Iten (1952). They recognised that the most important ore deposits are associated with anticlinal and domal structures and that granites may be a controlling factor in the localisation of the mineralisation. More recently a group of authors, Needham and Roarty (1980), Goulevitch (1980), Nicholson and Eupene (1984), Sanger-Von Oepen, Friedrich and Kater, (1988), Nicholson and Eupene (1990) and Kruse, Whitehead and Mulder (1990) have suggested an exhalitive syngenetic origin, or remobilised syngenetic during dolerite intrusion and/or regional deformation, for gold mineralisation, especially those associated with South Alligator Group lithologies (eg Bridge Creek, Mt Bonnie group of mines and Cosmopolitan Howley). Studies carried out at the Bridge Creek and Western Arm Prospects over the last three years suggest that syngenetic models for gold mineralisation are less relevant to gold mineralisation in the Howley District than first thought (Wall, 1989; Partington, 1990). The Bridge Creek prospect has been cited as an example of a syngenetic-syngenetic remobilised deposit (Oepen, Friedrich and Kater, 1988) while the Western Arm prospect is more clearly a vein hosted epigenetic deposit and a comparison of the styles of mineralisation at both prospects will be made. The nature of the gold mineralisation at both prospects will be described and compared, and possible genetic models for gold mineralisation and their relevance to regional exploration discussed.

Jan 1, 1994

By S Hapugoda

Iron ore oxide and oxyhydroxide minerals such as haematite (eg various types of martite and microplaty haematite), different forms of goethite, magnetite, hydrohaematite and kenomagnetite were analysed using optical microscopy, scanning electron microscopy (SEM) and electron probe microanalysis (EPMA) techniques, to determine the type and proportion of deleterious elements present and the chemistry of associated gangue minerals. The aim was to characterise elements potentially deleterious for agglomeration and steelmaking, eg sulfur, phosphorus, aluminium and silicon and correlate their distribution with mineral texture and association, to provide feedback on downstream processing performance and product quality.Examples of characteristic mineral associations are shown from various genetic styles of iron ores, including magnetite banded iron formation (BIF), BIF-derived martite-goethite and skarn-type magnetite ores.A number of examples are presented demonstrating the benefits of the use of combined techniques of reflected optical microscopy, SEM and EPMA data to reliably identify ore and gangue minerals and their associations in different types of iron ores.

Jul 11, 2011

By B P. Wrench, N R. Steward, C Wu

A gold mine in southern China has transitioned from an open pit operation to a fully underground mine. An overhand mining method is used which requires the mined stopes to be filled with backfill having an unconfined compressive strength of at least 0.35MPa. Tailings from the process plant is deposited into separate flotation and Carbon in Leach (CIL) tailings storage facilities. The tailings has a high fines content and the thickener on site could only produce a dilute flotation tailings at a solids content of about 30 wt%. This resulted in two undesirable outcomes: the density of flotation tailings in the Tailings Storage Facility (TSF) was significantly lower than planned so that the TSF could not store the life of mine tailings and that the backfill product had to include a high percentage of manufactured aggregate and increased cement content to achieve the required strength. This paper presents results of a tailings study which identified that the flotation TSF would be capable of storing the remaining life of mine tailings if an amended backfill product made up of 100% of flotation tailings could be introduced. A 100% tailings backfill with the addition of 8% cement was developed by classifying the tailings and using the coarser fraction in the backfill. This backfill allowed 60% of the flotation tailings to be placed underground and only the remaining 40% in the flotation TSF. A new thickener was designed and installed to thicken the tailings and rheological testing of the tailings, using a closed loop pilot plant, provided parameters to upgrade the underground reticulation system to deliver cemented backfill to stopes throughout the mine and to deliver thickened tailings to the TSF. The revised design was implemented and has resulted in considerable cost savings. CITATION:Steward, N R, Wrench, B P and Wu, C, 2018. Optimisation of surface tailings storage and tailings backfill – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 454–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R W. Wilson, A R. Branch, T S. Pooe

The original bulk air cooling system at this particular mine made use of two water chilling refrigeration machines to produce peak cooling of approximately 12 MWR with a downcast air temperature of about 7°C; however, as the shaft is not used for transporting personnel, the opportunity existed to supply more cooling to the mine by lowering the downcast air temperature. An ice storage facility has been constructed and provides a range of opportunities in operating the system: colder air temperature sent to the shaft, enabled by using near-zero degree water produced by melting ice to cool the air; electricity time-of-use management, by shifting electricity usage out of peak tariff periods; and increased peak cooling capacity, by melting ice while chilling water. Ice is created in the storage facility at night while the ambient air temperature is low and then melted to produce cold water when required by the cooling process. An ice dam was constructed and serpentine stainless steel coils installed where the ice is produced; one of the refrigeration machines was converted to chill a glycol solution to subzero temperatures to create the ice on the coils; a plate heat exchanger was installed to allow the glycol chiller to act as a water chiller as well; and a third spray stage was added to the bulk air cooler to utilise the near-zero water. This paper describes the thermodynamic design, construction and performance assessment of the new system, which is unique, novel and represents the state-of-the-art of this type of cooling system and energy management.CITATION:Branch, A R, Wilson, R W and Pooe, T S, 2015. Novel use of ice thermal storage for energy management on a mine refrigeration plant, in Proceedings The Australian Mine Ventilation Conference, pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By K Orth

The volcanic successions that host massive sulphide deposits are diverse in composition, facies types and facies relationships. They also show a variety of spatial and temporal relationships to mineralisation. In many examples, such as the Koongie Park Formation in Western Australia, the host succession includes more or less conformable syn-volcanic sills with peperitic contacts. Such sills can be an important source of heat for fluid circulation, influencing patterns of hydrothermal alteration and the location of co-eval and later mineralisation. The impact of syn-volcanic sills on the host succession depends in part on the initial porosity and permeability of the enclosing facies. The special properties of glassy pumice û being highly porous, permeable, and reactive û allow pumice-rich facies to preferentially focus hydrothermal fluid flow. However, the same properties promote early alteration and porosity reduction. Hence, the diagenetic and compaction history of pumiceous facies strongly influences their potential to host massive sulphide mineralisation. In contrast to pumice, dense glass has relatively low porosity, at least initially, and does not compact. Non-vesicular glass is a major component of submarine lavas, syn-volcanic intrusions and some volcaniclastic facies. However, especially in submarine settings, dense glass is commonly intensely perlitically fractured soon after eruption. The fractures greatly increase the porosity and permeability, locally accelerating diagenetic and hydrothermal alteration. In addition to false pyroclastic textures, altered perlite may exhibit false porphyritic textures. Silica- or feldspar-altered perlite kernels surrounded by intensely altered phyllosilicate domains can resemble phenocrysts in a fine grained groundmass.

Jan 1, 1999

By W Polkowski, M Tangstad, M Wallin, J Jiao

Fe-26Si-9B (wt per cent) alloy has been identified as a potential high-temperature phase change material (PCM) due to its attractive properties, such as its high latent heat of fusion and low volumetric change during solid/liquid transition. For the successful utilisation of this alloy into thermal energy storage (TES) systems, the development of a cost-effective production method is essential. Presently, the Fe-26Si-9B alloy is produced by mixing FeSi alloys with either pure boron element or FeB alloys. However, the use of pure boron is financially prohibitive, and the carbothermic reduction results in high greenhouse gas emissions and high energy consumption in the production of FeB alloys. In this regard, our study proposes a silicothermic reduction method to produce Fe-26Si-9B PCM by using FeSi alloys and B2O3-based oxides. Accordingly, the influence of various parameters on the production process was investigated, including operating temperature, holding time, B2O3 content in the added oxides, and initial Slag/Metal (S/M) ratio. Based on the experimental results, the optimal parameters for producing FeSiB alloys with over 9 wt per cent boron were determined. Consequently, it was documented that the FeSi alloys and the added oxides enriched with 50– 65 wt per cent B2O3 should be subjected to temperatures ranging from 1550–1650°C, maintain an initial S/M ratio exceeding 1, and ensure a holding duration beyond 1 hr. Moreover, the energy consumption of this process was estimated to be ~1.86 MWh/t metal and the mass loss was lower than 7 per cent. Therefore, silicothermic reduction offers a sustainable approach for producing FeSiB alloys with a boron content above 9 wt per cent.

Jun 19, 2024

By S H. Li, H Z. Gu, A Huang

High aluminium steel is a promising advanced steel known for its exception properties and holds significant economic and strategic importance. However, the CaO-Al2O3-SiO2 based slag with high alumina content reacts vigorously with alumina refractories during the smelting process at high temperature, seriously affecting the safe and efficient production of furnaces and resulting in the formation of Al2O3-MgO non-metallic inclusions within the molten steel. This is a bottleneck problem for high-quality steel refining, and the key reaction path during the corrosion remains unclear. The dissolution reaction mechanism of alumina refractories in high alumina CaO-Al2O3-SiO2 slags under a weak static magnetic field was investigated in this work, using high temperature laser confocal microscopy and in situ radiation spectroscopy techniques. The results indicate that the interaction between the high alumina slags and the alumina refractories is governed by free radical reactions. The dissolution of alumina forms AlO and AlO2 radicals. The reaction rate increases with the C/S ratio of the slag due to its low polymerisation. The reaction between non-bridging oxygen and AlO2 free radicals accelerates the generation of AlO and O2ꞏ- radicals. The reaction layer composed of calcium aluminate is formed through the recombination of AlO, Caꞏ+ and O2ꞏ- radicals. The weak static magnetic field induces the Zeeman splitting of free radical pairs and intersystem crossing occurs, promoting the formation of triplet free radical pairs through the hyper-fine coupling effect. The reaction can be significantly inhibited as the triplet free radical pair does not meet Pauli’s incompatibility principle. This discovery perfects the structure theory of molten slags with radicals and provides supplement to the design of the highly slag-resistant refractories, and provides the theoretical basis for the development of external field protection technologies for high-quality steel refining.

Jun 19, 2024

An intensive safety campaign at Mount Isa Mines Limited from 1956 to 1966 saw the lost time accident frequency rate fall to half its original level. A review of the safety programme was carried out in 1967 and in 1968 the Five Point Safety System was introduced. The seven years since its introduction have been years of significant achievement both in production and safety. Improving safety is a fundamental part of Mount Isa Mines Limited's policy and this system has been a major tool in implementing that policy. To be successful personnel need to be prepared and trained for its introduction and subsequently counselled on its use. A carefully prepared programme is required to phase in various aspects of the system and to make use of complementary steps. The system has been a success and it is anticipated that the continued drive to improve the use of principles of the system will further improve safety. It is hoped that this paper will be of value to those personnel concerned with industrial safety in Australia.

Jan 1, 1975

By L A. Balzan, F Nieuwenhuys

GEOSCAN on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape in South Africa, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption, and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech’s experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani’s GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis.

Nov 8, 2021

By U König

The use of high speed detectors made X-ray diffraction (XRD) an important tool for quality and process control in the mining industries. Besides knowledge about the mineralogy of a sample it provides useful information in terms of quantification of the crystalline phases and the amorphous content. Cluster analysis of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. The studies of this paper demonstrate how XRD and data clustering can be used for grade control, process optimisation and quality control of iron ores and iron ore sinters. These new developments have an enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron and sinter materials implemented in an industrial environment.

Jul 11, 2011

By C Harwood

Underground coal mines in the United States are in the process of completing installations for tracking and communication systems, mandated by Congress after a number of recent coal mine disasters. Yet, evaluation, modelling and testing of such systems has lagged due to legislated changes, abruptly introduced into the coal mining industry. System installation in a wide array of mine types, configurations, layouts and characteristics has provided a wealth of information regarding their potential in underground environments. Data collected from numerous installations for a variety of systems can be used to further define true capability and accuracy of communication and tracking packages. This paper describes a uniform means of evaluating the performance of a communication and tracking system. Several performance measures are proposed and described. These measures can also be predicted using an interactive software program. This program predicts the signal propagation, given the input mine characteristics and layout, with numerical and visual feedback. New or alternative system installations can also be more accurately designed to potentially minimise initial system cost and time required for trial and error installs. The focus of this research is to develop tools and protocols that can evaluate and measure the effectiveness of installed underground communication and tracking systems.

Nov 22, 2011

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

By H Arvidson, V Chamberlain, J Joughin, N Pollock, F Cessford, T Flitton, T Rowl

Environmental, social and governance issues (ESG) have become a defining feature in the marketplace to differentiate preferred investments. With the sustainability commitment and reporting landscape anticipated to evolve exponentially, it is now imperative to rapidly develop the approach taken by mineral companies to adequately identify and address ESG risks and opportunities in the reporting of Mineral Resource and Mineral Reserve (MRMR). MRMR cannot be effectively reported as technically and financially assured and realistically executable, if ESG is not integrated into the strategy, business model, input assumptions and process that defines and drives robust MRMR public reporting. Regulatory reporting codes across the globe are presently in various stages of being updated and modified to ensure ESG factors are appropriately covered as a key part of diligent and transparent disclosure. Security exchanges are making it clear that companies must not omit ESG risks from reports to investors. This paper discusses associated challenges for MRMR reporting and suggests avenues for improvement. Key themes include: the importance of procedure rather than prescription and checklists; how ESG criteria impact Modifying Factors and determination of Reasonable Prospects for Economic Extraction (RPEE); the need for financial models to account for material ESG commitments; the uniqueness of each mineral asset; the need for education, upskilling and accreditation of both ESG experts about MRMR reporting and equally Competent Persons in ESG matters; and the need for clear and balanced reports that meet the needs of end users. (RPEE is adopted here for simplicity and consistency, recognising that some reporting codes still include ‘Eventual’ in the term (ie RPEEE). Whilst RPEE and RPEEE are subtly different the intent is to point to the process of assessing ESG factors in determining reasonable prospects.) The principles of transparency, materiality and competence remain paramount when considering the impact of ESG matters on MRMR reporting, and this necessitates an inclusive, cohesive, and integrated approach to assessing ESG issues to ensure the necessary expertise and diligence is applied.

May 24, 2023

Refractory gold concentrates and their roasted products have been examined by mineralogical and chemical methods, and the distribution of gold in the tailings after leaching has been Investigated.

Jan 1, 1989

A method for determining the relative degree of oxidation of concentrate samples was established, and various surface-active materials and protective systems were examined as oxidation inhibitors. Sodium oleate was-the most effective of the materials tested, and a plant trial

Jan 1, 1963

China has at least 200 collieries suffering from the problem of instantaneous outbursts of coal and gas. Strong outbursts often have occurred in geological tectonic zones and concentrated stress areas. There are some particular characteristics of these strong outbursts, including the effects of ground stress, gas pressure and the properties of coal associated with the outbursts.

Jan 1, 1986

By Stewart Gillies AD

Resource rent taxes are taxes which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. Resource Rent Taxes have from time to time been considered for implementation in both Australia and New Zealand. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax.

Jan 1, 1995

By Newell R

The influence of layering on the rate of heat transfer through a packed bed consisting of particles of two different sizes and heat capacities has been determined by measuring the heat front velocity through beds of quartzite particles and iron ore pellets. The heat front velocity through the layered beds was less than that through a bed consisting of a random mixture of the par- ticles. This is due to the formation of an interface in which the smaller pellets in one layer penetrate into the layer of quartzite Below.

Jan 1, 1987