Search Documents

Pulverised coal firing was pioneered in the cement industry prior to the turn of the century. Ash from the coal is absorbed into the mix in the kiln and replaces secondary materials. With high purity limestone coal with high ash content can be used. Fuel cost is a major part of the total manufacturing cost. Cement plants are thus quick to respond to fuel price changes and will use low grade fuels if there is a price advantage. Combustion conditions in a cement kiln differ markedly from a boiler. Flame length is determined by air/fuel mixing but because of fixed secondary air conditions this depends on primary air momentum. Volatile content has some effect on flame length but this can be offset by coal fineness. Much of the heat for cement production is for limestone calcination which is a low grade energy requirement. By allowing long residence time in separate direct fired vessels which then feed the high temperature kiln the energy of materials such as oil shale, tyres and lump lignite can be utilised.

Jan 1, 1987

By Scaife PH, Cripps Clark J, Cameron DB

Tuyere coke samples have been taken through the tuyere openings of B.H.P. International Blast Furnaces since 1978 with Whyalla No. 2 Blast Furnace taking samples on a regular basis since 1982. The degradation of coke during it's passage through the Blast Furnace can be measured and the relationships between these data, feed coke data and blast furnace operating data demonstrated. Tuyere coke sampling has been useful in revealing misleading external coke testing results and is still the method to monitor directly the performance of coke within the Blast Furnace.

Jan 1, 1987

By Just GD, Phillips R

The application of high pressure water jet technology to the drilling of longholes in coal has resulted in the development of a system currently capable of drilling to lengths greater than 200m. Field tests at the German Creek Mine have demonstrated directional control of the holes within a 0.5m section of the seam. Initial application of the technique at the German Creek operations is for drilling methane drainage holes. These developments, in three stages, result from support by the National Energy Research Development and Demonstration Council

Jan 1, 1991

In May 1977 a new dam was commissioned for disposal of 600,000 metric tonnes/year of tailings. Design basis, costs and construction problems are described. Problems arose, assoc- iated with lack of experience in building such a dam "from scratch". Solutions are described land costs given.

Jan 1, 1978

From the viewpoint of mechanical efficiency, charges should be fully coupled and, upon detonation, should just fail to break the rock in compression. But because mining thrives on its cost-effectiveness rather than its mechan- ical efficiency, the explosive which generates maximum energy per $ should generally be used, even though the mechanical efficiency of this explosive's detonation products may be sub- optimum. Wherever possible, each charge should have a length:diameter ratio of about 20 or more and should shoot to a concavely biplanar free face that is both parallel and reasonably close to the blasthole. Success in obtaining parallel effective faces often demands the drilling of angled blastholes and, hence, will require intensified research and development efforts by drilling manufacturers, especially where hard strong rocks are encountered. Blastholes should be drilled on equilateral triangular grids and fired in a Vl or shallower V-type sequence using inter-row delays which ensure that good pro- gressive relief of burden is achieved. The conventional method of calculating Se/Be values (on the basis of planar effective faces) is often invalid.

Jan 1, 1986

By Bennet A. G

An overall review of the selection of rock strength and deformation characteris- tics for the design of the Melbourne Under- qround Rail Loop (MIJRL) rock tunnels is presented. Particular emphasis is placed on aspects of in-situ testing, including large diameter plate bearing tests. Material on the interpretation of test results for use in the design of the tunnel linings and openings is included, with a brief discus- sion of desiqn methods.

Jan 1, 1981

By Liu Z. C

Evans' theory for chisel shaped picks is well known in the field of rock cutting technology. It has been widely accepted as a good mathematical description of how coal and other rocks break under the action of a simple wedge or chisel. Subsequently, Evans proposed a corresponding theory for pointed shaped picks. Theory along with experimental evidence from the laboratory has consistently shown that chisel picks are more efficient than pointed picks. However despite such evidence, pointed picks continue to be the preferred shape in most practical cutting applications. Evans' theory for pointed picks was developed in an attempt to shed light on this apparent incongruity. The theory although predicting forces of the right order was found to be deficient in several respects. This paper examines Evans' theory for pointed picks and proposes changes to it, which brings the theory much more into line with measured data. The issue of the relative efficiencies of chisel and pointed shaped picks is also examined on a theoretical basis and the apparent incongruity is Resolved.

Jan 1, 1995

It is important to prevent the overload ing of mills being operated near maximum tonnage. Changes occurring during overload differ in their usefulness as guides to control action. The Primary Ball Mills of Bougainville Copper Ltd. provide an example of some of the problems and progess in avoiding overload.

Jan 1, 1978

By Denholm W. T

The SMELT-2 package is specifically designed to perform on-line simulation of smelting processes. This paper describes its application to the simulation of continuous matte converting followed by reductive slag cleaning in SIROSMELT reactors. The matte, containing 50% Cu is assumed to be produced at the rate of 20 tph in a continuous matte smelting furnace such as an Outokumpu Flash Furnace, Noranda or Sirosmelt reactor. Two alternative fluxing strategies in the converter are examined, namely: ò conventional silicate slags, ò calcium ferrite slags, and the flow sheets associated with each strategy are discussed. A regular solution model is used in the present study to account for the variations in the activity coefficients of components in the slag.

Jan 1, 1989

By Mowat BA, Leach TM

The Morobe Goldfield in Papua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23t) and Edie Creek (40 and geological resources have been established at Hidden Valley (780, Kerimenge (360 and Hamata (30t). Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.

Jan 1, 1995

By Eyers G. C

Long Shaft was initially developed using a rail haulage system on every working level comprising battery electric locomotives and granby trucks loaded by rail mounted rocker shovels. Production was commenced using conventional hand held cut and fill mining methods. In an effort to improve productivity and reduce operating costs a mechanised cut and fill stoping method evolved to suit the wider sections of the orebody. To further improve productivity and reduce costs the mechanised levels of the mine are progressively being redeveloped to enable the use of trackless diesel haulage equipment. An added benefit of trackless haulage equipment will be the ability to place development mullock into stopes as Fill.

Jan 1, 1988

The Ida Valley in Central Otago is one of series of parallel basins filled with freshwater sediments. The basins are in fact tectonic depressions superimposed on NE trending grabenlike structures which occur in the area and are the result of block faulting possibly initiated in Cretaceous times and concluded in late Tertiary and early Quaternary. In Central Otago this tectonic event affected metamorphosed rocks belonging to the eastern facies of the New Zealand Geosyncline and collectively known as the Haast Schist Group. These rocks constitute the basement and the shoulders of the tectonic depressions. The Ida Valley occupies the depression wedged in between the Raggedy Range to the NW and the North Rough Ridge in the SE. The valley is approximately 38 km long, 3 to 7.5 km wide and is drained by the NE flowing Pool Burn, which meets the SW flowing Ida Burn. The resulting unified stream flows into the Manuherikia river which drains the next door depression to the NW. The present work deals with the Ida Valley basin and more specifically with the geology studied within two Prospecting Licence areas held by Gold Mines of NZ Ltd on the southeastern flank of the valley.

Jan 1, 1977

Faced with low prices and weak demand in an oversupplied market, the Australian coal industry must seek to further reduce its costs. The paper examines minesite competitiveness of the open cut coal industry in Australia with some references to the coal operations of M.I.M. Holdings Limited. The make-up of F.O.R. mine costs is analysed in order to identify where efforts should be directed to maintain competitiveness. The scope for mine site improvements through changes to working practices, the application of new technology and cost management is examined.

Jan 1, 1987

By Giannini LM, Carras S

A fundamental problem in mine planning is that of determining the "optimum pit limit" of a mine. This optimum pit limit yields information which is considered essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long -, intermediate -, and short-range mine plans. Since the mid 1960's a number of mathematical techniques based on the "block model" have been proposed for solving this problem. When applied to large ore-bodies the implementation of these techniques, especially the more elaborate ones, poses considerable computational problems. In this paper we report on our work, done jointly with Systems Research Institute of Australia (SRIA), in devising strategies for overcoming these Problems.

Jan 1, 1986

By S F. Simmons, A McOnie, J L. Mauk

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water whereas the mineral assemblage of replacement calcite-interstratified illite û montmorillonite-kaolinite forms a carapace and reflects formation from a CO2-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

The Curragh coal mining operation was designed and constructed to produce two coals initially at a rate of 4.3Mtpa. These are a high thermal energy steam coal primarily for domestic electricity generation and a low ash high quality coking product for the export market. Treatment of coals from four seams to achieve this requires a large and complex preparation plant and blending facilities incorporating state of the art technology. This facility was constructed during 1982/83. It has been designed for expansion to 6.8Mtpa capacity. The preparation and handling facilities were built at a cost of approximately A$80 million. Equipment includes 500 plus electric drives with a total capacity of 20 000kw. Commissioning was carried out in three phases : Staging - of the control system Coal Handling Facilities - conveyors, stackers and reclaimers for raw and product coals The Coal Preparation Plant - heavy media cyclones and froth flotation. A period of three months was devoted to the commissioning of the plant before requiring product coal to contract specification. This paper will describe the planning, implementation and results achieved.

Jan 1, 1986

By Kinsella B

Titrimetric studies have been carried out on the activated carbons Kintal 1105, Norit 2520 and Kuraray 2GA. Titration curves of the carbons before and after acid and water washing and gold loading indicate that the acid-base properties of the carbons are affected by both the method of treatment and also by the loading of gold. It is considered that the pKa values of the functional groups on the carbon surface are in the regions of 11, 7 and 3 respectively.

Jan 1, 1984

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

A critical appraisal of the wide variety of processes used in the pyrometallurgical production of metals and non-metals shows that there is a strong physico-chemical and, in particular thermodynamic, basis for the variety. Based on this, a simple classif- ication scheme has been developed which makes it possible to understand the methods for extracting individual metals and non-metals pyrometallurgically and to assess which are the more attractive routes. The analysis presented shows why there are essentially two broad routes for pyrometallurgical production of metals and non-metals; viz., the reduce- refine and the refine-reduce routes. Halides have the role in pyrometall- urgical processing of producing pure compounds for subsequent reduction. The criteria which determine the selection of reduction method for oxide raw materials and intermediate halides (e.g., use of carbon, hydrogen, a more reactive metal or electrowinning) are examined critically in the paper. The treatment of sulfide raw materials is considered also, particularly the criterion for smelting sulfides directly to the metal.

Jan 1, 1987

Tyre cost at Mount Morgan Limited had been 24% of the truck operating cost. Comprehensive tyre testing resulted in a reduction in tyre costs of about one third. A record of the evaluation techniques may enable the selection of tyres that are most suited to particular conditions. Rubber characteristics, rubber quantity, tyre design, road conditions, dump conditions and inflation pressure were found to be sig- nificant variables. Measurements of tyre temperatures at the breaker strip were used to select the tyre design and inflation pressure required for Mount Morgan Limited's conditions. Relugging of tyres was discontinued as a result of tyre testing.

Jan 1, 1974