Search Documents

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

JULY was a month of great turmoil, both economic and political, in many parts of the world. Instead of conditions improving, they seem to have been getting worse. In Ireland, civil war is still in progress. Germany was in the throes of a political upheaval. The meaning of the assassination of Rathenau became clear. It evinced the development of a class struggle between the bourgeois and socialistic parties which may rock the country to its foundation and will increase the difficulties of arranging things with the French and solving the reparations problem. In Poland, a similar contest is developing. Austria is already so completely contaminated by the socialist element that it is unable to get outside assistance and is thus falling into a state of despair but little short of what prevails in Russia. The conference at the Hague came to an abortive end for the reason that it was impossible to discuss affairs with the Russians in any reasonable way. The Germans declared their inability to meet the reparation payment that fell clue on July 15 and the Commissioners for the Allies granted them an abate-ment of a portion thereof and are listening attentively to the supplication of the Germans for a moratorium of one or two years. In the United States, July was a month of widespread labor troubles, accompanied by a great deal of disorder and violence, which led to detachments of the National Guard being called out in several states. The railway shopmen, about 400,000 in number, struck on July 1. The road maintenance men decided not to strike, but many thousands of them quit work without the sanc-tion of their union. There were more strikes in the textile industry in New England and in similar industries all over the country. Early in July, it was estimated that about 1,250,000 men were out on strike. The coal strike continued. Early in the month the President summoned operators and miners to Washing-ton and submitted a plan for the compromising of disputes. After a week's consideration the miners re-fused flatly to agree to anything. The majority of the operators consented to accept the proposed arbitration, but a minority refused. Following this abortive at-tempt the President dismissed the conference with the injunction "to return to your mine properties and resume operation." Production has not increased.

Jan 8, 1922

By W. H. Hough, P. B. Leavenworth

Development in the upper Texas Gulf Coast during 1944 resulted in the discovery of 19 new fields as compared with 11 during 1943. These discoveries include 10 oil fields, one dry gas field, and eight gas-condensate fields. Drilling During the year 590 wells were drilled as compared with 418 drilled during 1943. Of these operations, 485 wells were drilled in proven fields, with the following results: 281 oil wells, 22 condensate wells, one dry gas well and 141 dry holes. The remaining 105 wells were wildcats, of which 19 were producers. The geological distribution of these discoveries was as follows: In 1944, production amounted to 178,-522,630 bbl., which was an increase of some 31,670,384 bbl. over the 1943 figure of 136,852,246 bbl. These figures include both condensate and oil production, as separate figures are not available. Wildcatting in the area was more successful during 1944 than in 1943 as the following comparison of number of wells drilled illustrates: Discoveries during 1944 Smith Point, Chambers County.—Standard Oil Company of Texas completed its No. I State, sec. 109, on Feb. 15, 1944, in a Frio sand at 8135 to 8146 ft. The well flowed 250 bbl. of 42º gravity oil through an 1/8-in, choke. Gas-oil ratio was 800 to I; tubing pressure, 1100 bbl. Four other oil wells and one gas well were completed during the year. This discovery does not appear to be of major importance. The producing area lies on the upthrown side of a large fault. North Winnie, Chambers County.—Sun Oil Co. completed No. I P. E. Dougherty on Apr. 27, 1944, from the Frio, through perforations at 8757 to 8759 ft. The initial production was 154 bbl. of 38.3º gravity oil through an 1/8-in. choke. Gas-oil ratio Was 2526 to 1; tubillg Pressure, 2280 1b.; casing Pressure, 1225 lb.; total depth, 9519 ft. Three other wells were drilled during the Year. This discovery is on the downthrown side of the major Winnie Stowell fault, and increases in magnitude the already large producing area along this fault. Mayes Field, Chambers County.—Humble Oil and Refining Company's No. I Mary Etta Mayes was completed on Dec. 24, 1944, in a Frio sand, at 8166 to 8169 ft. through 1/4-in. for 768 bbl. of 40.3º gravity

Jan 1, 1945

TENTATIVE -reservations for the cruise to Vene-zuela and the West Indies have been coming in nicely, but there is plenty of room yet for mem-bers and their friends. The exact schedule is even yet not entirely fixed. Owing to difficulty in securing the release. as, early as had been hoped, of the Lapland, which is so particularly well adapted to this cruise, the time has been shortened. The steamer is now scheduled to sail at midnight on Jan. 30 or 31, the exact date still to be determined, and to return on Feb. 20. This change will so shorten the time as to permit many more to attend as they need not be so long. away from their business. It .will necessitate cutting out the pro-posed day at Kingston in Jamaica, and, if the steamer is -not available until Jan. 31, may also necessitate passing Bermuda without a stop. The time remaining will, however, allow a stop of one and a half days at Havana, a full day, on the Canal, Zone with opportunity to go through the locks, the Culebra Cut, and to see Panama, and the five days, planned in Venezuela: Just how many can be taken into Lake Maracaibo and the oil fields will depend on the local transportation that can be made available. It may be necessary to restrict this shore party as to numbers, but if so, something interesting will be provided to fill the time of the others. At other points accommodations will be ample for all Members of the excursion will get back in time to register and attend the smoker on the opening day of the meeting as also possibly the Monday after-noon sessions if any be held. The usual Institute rules for excursions will be fol-lowed assigning space in the order of application with members first. Guests vouched for by members will be heartily welcomed. The steamer rate varies accord-ing to the accommodations chosen. There are a limited number of one and two berth rooms at the minimum of $250 per passenger with plenty of room at $300 to $500, according to space and location. At prices from $750 up per passenger rooms with private bath are to be had. Plans are on the-basis of two people in a three-berth room. The steamer, which is especially fitted for crusing, has ample deck-space and numerous large

Jan 11, 1927

By Charles E. Lees

The Globe Mining District is in the southeast central part of Arizona, in Gila County. Globe, with a population of about 7000, is the terminus of the Arizona Eastern R.R., a branch line 130 miles long that connects with the Southern Pacific R.R. at Bowie. In 1874, prospectors crossing the Pinal Mountains from the west located what is generally known as the Old Dominion mine. For several years, it attracted little attention, because of the greater interest aroused by the discovery of high-grade silver ores in some of the foothills northeast of Globe. About six years later, the prospector turned his attention to the abundant copper ore revealed by surface workings along the Old Dominion vein, and, in 1884, the Old Dominion company erected two 30-ton furnaces. From 1888 to 1893, the Old Dominion company is said to have maintained an average annual production of about 8,000,000 Ib. of copper. Until Dec. 1, 1898, all supplies had to be freighted into Globe by wagons and the mines of the district operated intermittently because of high expenses, but with the advent of the railroad the Old Dominion company continued to be a large and steady producer. In the Globe district, the production of copper far exceeds in importance that of any other metal. There are four operating companies along the Old Dominion vein and the total annual product of these properties for 1923 was about 45,000,000 lb. of copper. The unit size of the mineral tracts in the district is the regulation mining claim, 600 ft. wide by 1500 ft. long, and all ownerships are held in fee. Globe is 3600 ft. above sea level, and lies between the Apache MOUntains to the east and the Pinal Mountains to the west. The principal drainage of the district is northward through Pinal creek into the Salt River. The general slope from the high point along the vein, where the Superior & Boston mine is, to Pinal creek, where the Old Dominion mines are, is about 250 ft. to the mile. Geology The oldest rocks in the district are pre-Cambrian crystalline schists known as the Pinal schist, which are the basement upon which all the later rocks were deposited. These latter rocks comprise shale, con-

Jan 1, 1925

By H. M. Morse

Tinsley Oil Field.—Mississippi joined the oil-producing states when on Sept. 13, 1939, the Union Producing Company's G. C. Woodruff well No. 1, sec. 13, T. 10 N., R. 3 W., Yazoo County, was completed after drilling plug at 4540 ft. in the Woodruff sand of the Eutaw formation of Cretaceous, producing 300 bbl. per day of 34.4" gravity oil through a ¼-in. choke, with a gas-oil ratio of 80 to 1 and bottom-hole pressure of 2045 lb. This was the discovery well in the Tinsley oil field. The well was drilled to a total depth of 4567 ft. and no salt water was encountered. The sand underlies the Selma chalk formation. Nine producing oil wells and one dry hole were drilled and completed by the end of 1939. Two producing sands have been found in the Eutaw and a third sand in the top of the Tuscaloosa formation, called the Woodbine sand in Louisiana and Texas. Faulting is an important factor in the Tinsley field. Total oil production has been approximately 250,000 bbl. from the nine flowing wells. Total depth to top of productive zone was 4540 ft.; to bottoms of productive wells, 4580 ft. Net thickness of the producing formation is 20 to 40 ft., and its porosity is 24 per cent. The deepest zone tested was the Tuscaloosa, in which the depth of hole was 6112 feet. Six hundred and forty acres has been proved for oil production. Jackson Gas Field.—The Jackson gas field has shown a steady decline in the number of wells but the pressure has been maintained. This field is a perfect example of a water-driven field and the time of wells going to salt water is predictable. Five wells were drilled in the Jackson field, of which only one produced. Amory Gas Field.—Interest was renewed in the Amory gas field, where a new well was started in the fall of 1939. Geological Formations.—The deepest well drilled in 1939 was the Willmut Gas and Oil Company's Cleve Love S. F. Johnson No. 1, sec. 29, T. 6 N., R. 1 W., Hinds County. This well encountered the Lower Cretaceous, Trinity series from 3770 to 6422 ft.; Lower Mesozoic from 6422 to 6484 ft. The geological correlations and nomenclature of the formations in Mississippi are shown in the accompanying strati-graphic section.

Jan 1, 1940

By H. M. Morse

Tinsley Oil Field.—Mississippi joined the oil-producing states when on Sept. 13, 1939, the Union Producing Company's G. C. Woodruff well No. 1, sec. 13, T. 10 N., R. 3 W., Yazoo County, was completed after drilling plug at 4540 ft. in the Woodruff sand of the Eutaw formation of Cretaceous, producing 300 bbl. per day of 34.4" gravity oil through a ¼-in. choke, with a gas-oil ratio of 80 to 1 and bottom-hole pressure of 2045 lb. This was the discovery well in the Tinsley oil field. The well was drilled to a total depth of 4567 ft. and no salt water was encountered. The sand underlies the Selma chalk formation. Nine producing oil wells and one dry hole were drilled and completed by the end of 1939. Two producing sands have been found in the Eutaw and a third sand in the top of the Tuscaloosa formation, called the Woodbine sand in Louisiana and Texas. Faulting is an important factor in the Tinsley field. Total oil production has been approximately 250,000 bbl. from the nine flowing wells. Total depth to top of productive zone was 4540 ft.; to bottoms of productive wells, 4580 ft. Net thickness of the producing formation is 20 to 40 ft., and its porosity is 24 per cent. The deepest zone tested was the Tuscaloosa, in which the depth of hole was 6112 feet. Six hundred and forty acres has been proved for oil production. Jackson Gas Field.—The Jackson gas field has shown a steady decline in the number of wells but the pressure has been maintained. This field is a perfect example of a water-driven field and the time of wells going to salt water is predictable. Five wells were drilled in the Jackson field, of which only one produced. Amory Gas Field.—Interest was renewed in the Amory gas field, where a new well was started in the fall of 1939. Geological Formations.—The deepest well drilled in 1939 was the Willmut Gas and Oil Company's Cleve Love S. F. Johnson No. 1, sec. 29, T. 6 N., R. 1 W., Hinds County. This well encountered the Lower Cretaceous, Trinity series from 3770 to 6422 ft.; Lower Mesozoic from 6422 to 6484 ft. The geological correlations and nomenclature of the formations in Mississippi are shown in the accompanying strati-graphic section.

Jan 1, 1940

By W. F. Boericke

THE character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed, a flat generally well-defined clay seam a few inches thick, which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.1 Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 2, 1922

By Leon Orlowski

THE oil-bearing districts of Poland are found on the slopes of the Carpathian Mountains. The oil belt extends from Gorlice southeast to Stanislawow. It is approximately 250 miles long and 30 miles wide, and comprises four geological districts: the western, or Gorlice district; next, to the east, the Krosno district; the Boryslaw district; and, in the extreme southeast, the Stanislawow district. The amount of petroleum produced in Poland from the beginning of the oil industry scarcely totals 26,000,000 metric tons, or 15 per cent. of the estimated supply. Of this amount, 18,000,000 tons have been taken from the fields of Boryslaw within 25 years; and only about 8,000,000 tons from all other fields within a period twice as long, although some of these other fields represent just as good possibilities as did Boryslaw at the beginning of its development. The Polish oil industry was severely stricken by the war. The retreating Russian armies, in 1915, destroyed a large number, of the existing oil wells, nor was the post-war period favorable for the development of this industry;; the money and credit stringency interfered with the expansion of drilling. But since 1921 there has. been a slow steady increase in production and there is now every reason to believe that conditions in the industry will improve. In fact, an increase in new drillings has been reported for the current year. The production of crude oil in Poland, in 1913, amounted to 1,113,668 metric tons. In 1914, the production declined- to 655,600 metric tons. In 1921, the production was 705,596 tons; in 1922, 712,428 tons, and in 1923, 737,182 tons; or more than 5,000,000 bbl. But the fields have a much greater potential output, which could be realized were the capital available for prospecting and new drilling. The principal producing, and at present most exploited, fields are around Boryslaw and Schodnica. These fields were developed rapidly for in the first year of their modern exploitation the wells were gushers of moderate depth. However, as a result of heavy drilling, the shallow folds have been exhausted and oil can be reached now only by deep drilling. Wells of almost 5600 ft. have been drilled in Boryslaw. Because of these drilling conditions, a large number of engineers and workmen specially skilled in deep drilling are to be found in this field.

Jan 3, 1925

By John Birkinbine

(Read at the Philadelphia Meeting, February, 1878.) IN a former paper* attention was directed to the various firms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal furnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillating engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter *Transactioiis of the American Institute of Mining Engineers, vol. p. 455.

Jan 1, 1878

By Curtis L. Graversen, J. H. Hamilton, John C. Nixon, John R. Lewis

RECENTLY there has been much speculation concerning the advantages of using oxygen enriched air or pure oxygen in pyrometallurgical processes. The advantage of using oxygen in the iron blast furnace and elsewhere in ferrous production metallurgy has been given careful consideration and, as a result, several experiments have been tried and a number of papers have recently appeared on this subject.1.2 The use of oxygen in nonferrous smelting likewise poses interesting problems, therefore any experimental data obtained in this area should likewise be of general interest.3 Ashcroft4 in 1933 claimed to have obtained improved results when copper concentrates were roasted in pure oxygen. However, his' paper gives neither data nor experimental details. A few years ago a research program was started in this laboratory which had for its objective the determination of the mechanism of oxidation of metallic sulfides under varying conditions. To date we have studied the oxidation of galena, 5 sphalerite, and chalcocite. It is a well known fact that copper sulfide minerals are oxidized slowly by weathering agents, so that the sulfides of copper which find their way into a tailing pond are gradually changed into watersoluble and acid-soluble compounds. Commercially, the oxidation of copper sulfide minerals is accomplished by roasting them at elevated temperatures in air using a suitable (usually multiple-hearth) roaster. Most copper smelters are equipped with such roasters. In this phase of the study we were especially interested in determining the effect of temperature on: (I) the air oxidation of chalcocite and (2) the oxidation of chalcocite using commercial oxygen. The amount of sulphur removed as sulphur dioxide, the percentages of water-soluble copper, and of acid-soluble copper were determined for the air oxidation tests. In the tests using commercial oxygen, the percentages of sulphur dioxide, water-soluble copper, acid-soluble copper, water-soluble sulphur and acid-soluble sulphur were determined. For these experiments the temperature was varied from 250 to 700°°C. EXPERIMENTAL Preparation of Chalcocite (Cu2S) Natural chalcocite is not pure. Minerals such as bornite, covellite, and chalcopyrite may be present. It was decided, therefore, to prepare some chalcocite in our own laboratory. An intimate mixture of sulphur and finely divided metallic copper in the ratio of 4 g of copper to I g of sulphur was prepared. To this was added a slight excess of

Jan 1, 1948

By K. BRUCE DAVIDSON

-The North Central Texas area includes the following counties in Railroad Commission of Texas District 7-B: Brown, Callahan, Coleman, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Haskell, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, S

Jan 1, 1946

By J. H. Hamilton, J. R. Lewis, J. C. Nixon, C. L. Graverson

Recently there has been much speculation concerning the advantages of using oxygen enriched air or pure oxygen in pyrometallurgical processes. The advantage of using oxygen in the iron blast furnace and elsewhere in ferrous production metallurgy has been given careful consideration and, as a result, several experiments have been tried and a number of papers have recently appeared on this subject.1,2 The use of oxygen in nonferrous smelting likewise poses interesting problems, therefore any experimental data obtained in this area should likewise be of general interest.3 Ashcroft4 in 1933 claimed to have obtained improved results when copper concentrates were roasted in pure oxygen. However, his paper gives neither data nor experimental details. A few years ago a research program was started in this laboratory which had for its objective the determination of the mechanism of oxidation of metallic sulphides under varying conditions. To date we have studied the oxidation of galena,5 sphalerite, and chalcocite. It is a well known fact that copper sul-phde minerals are oxidized slowly by weathering agents, so that the sulphides of copper which find their way into a tailing pond are gradually changed into water-soluble and acid-soluble compounds. Commercially, the oxidation of copper sulphide minerals is accomplished by roasting them at elevated temperatures in air using a suitable (usually multiple hearth) roaster. Most copper smelters are equipped with such roasters. In this phase of the study we were especially interested in determining the effect of temperature on: (I) the air oxidation of chalcocite and (2) the oxidation of chalcocite using commercial oxygen. The amount of sulphur removed as sulphur dioxide, the percentages of water-soluble copper, and of acid-soluble copper were determined for the air oxidation tests. In the tests using commercial oxygen, the percentages of sulphur dioxide, water-soluble copper, acid-soluble copper, water-soluble sulphur and acid-soluble sulphur were determined. For these experiments the temperature was varied from 250 to 700°C. Experimental Preparalion of Chalcocite (Cu2S) Natural chalcocite is not pure, Minerals such as bornite, covellite, and chalcopy-rite may be present. It was decided, therefore, to prepare some chalcocite in our own laboratory. An intimate mixture of sulphur and hool divided metallic copper in the ratio of 4 g of copper to I g of sulphur was prepared. TO this was added a slight excess of

Jan 1, 1949

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By Brian F. Dyson

The surface tensions at 1550°C of some Fe-S alloys (in the range 0.008 to 0.052 wt pct S), Fe-Sn alloys (0.31 to 48.4 wt pct Sn), Fe-P alloys (0.038 to 2.38 wt pct P), Fe-Cu alloys (2.15 to 22.8 wt pct Cu), and Fe-1 pct C-S alloys (0.005 to 0.076 wt pct S) along with the surface tension of the base iron have been measured by the sessile-drop method. A mean value of 1754 dynes per cm was found for the surface tension of the base iron. Sulfur was found to be highly surface-active, the surface-tension results being in quantitative agreement with existing data. Tin and copper were found to be less surface-active than sulfur while phosphoms was completely nonsurface-active. The surface tensions of Fe-1 pct C-S alloys were found to be lower than those of the Fe-S alloys containing the same sulfur content. This was shown to be a mmzifestation of the increase in the thermodynamic activity of suZfur by carbon. It is only in recent years that attempts have been made to measure the surface tension of liquid iron of known high purity.1-3 Earlier measurements4-7 were made on liquid iron containing variable amounts of what are now known to be surface -active solutes. The exact value of the surface tension of liquid iron is still, however, open to some doubt. Halden and Kingery&apos; reported a value of 1720k 34 dynes per cm at 1570°C, Kozakevitch and Urbain8 gave 1790k 25 dynes per cm at 1550°C, while Van-Tszin-Tan et al. obtained a value of 1865k 37 dynes per cm at 1550°C. The first systematic investigation into the effect of controlled solute additions on the surface tension of iron was made by Halden and Kingery.&apos; They showed that sulfur and oxygen were highly surface-active, whereas nitrogen was only slightly active, and carbon inactive. A subsequent investigation by Kingery indicated that two other group-6B elements, selenium and tellurium, were also surface-active. This highly surface-active nature of sulfur and oxygen has recently been substantiated by Kozakevitch and Urbainla and Van-Tszin-Tan et al. l1 Kozakevitch and Urbainl2 have also conducted an experimental survey of the effects of a number of metals on the surface tension of liquid iron. Their surface-active nature was, in all cases, less than that of the group 6B elements. The present investigation was undertaken to study in more detail the surface tensions of dilute Fe-S alloys and to measure the surface tensions of binary alloys of iron containing phosphorus, copper, and tin. The effect of sulfur additions on the surface tension of Fe-1 pct C alloys was also determined. EXPERIMENTAL PROCEDURE The sessile-drop method was employed in the present investigation. An apparatus was built similar in principle to that described by Humenik and Kingery.lS It consisted of a horizontal silica tube, which could be evacuated to pressures less than 10-5 torr, with its central portion surrounded by a water jacket within which was a high-frequency coil. This generated heat in a tantalum susceptor placed inside the silica tube, which in turn radiated heat to the specimen mounted on a recrystallized alumina plaque. Temperatures were measured by an optical pyrometer and photographs of the molten drop were taken on a fixed-focus plate camera giving a magnification of X2. Surface-tension values were determined from the resultant drop using the method described by Baes and Kellogg.l4 The high vapor pressure of molten iron made it necessary to conduct all the experiments under a 1/4 atm of argon (greater than 99.995 pct purity). The analysis of the base iron used in the investigation is given in Table I. Each sample was approximately 3 g in weight and had a hemispherical base to ensure a uniform advancing contact angle on melting. The iron alloys were prepared individually in the sessile-drop apparatus by drilling a hole in the top of each sample and adding the required amount of solute, the drops being analyzed after the experiment. This method of preparation had the advantage of ensuring a consistent minimal contamination by oxygen due to refractory attack and also allowed surface tension to be measured at the same time. Every precaution was taken to ensure that the specimen was not contaminated by grease when it was introduced into the apparatus, the samples being cleaned in acid, dried in alcohol, and rinsed in petroleum ether. All handling was done with tweezers. Once the specimen had been placed inside the susceptor, the furnace was evacuated and the Sample leveled. The furnace was then degassed at approximately 1000"C before the argon was introduced. In every case the surface tension was determined at 1550" C.

Jan 1, 1963

By R. S. Handy

THE properties of the Patiño Mines and Enterprises Consolidated, Inc., a New York corporation, are near Llallagua in the department of Chayanta in the west central part of Bolivia, South America, about 80 miles southeast of Oruro and 250 miles southeast of La Paz, the largest city in Bolivia and its virtual capital. The properties are accessible by railroad from three points on the west coast-from Mollendo, Peru, across Lake Titicaca, from Arica by way of La Paz, and from Antofagasta, Chile. The latter route, although the longest, is recommended by the companies as affording a more gradual introduction to the high altitudes; the mine being 13,000 ft. above sea level. The company operates its own railroad from its properties at Uncia to Machacamarca on the Chile & Bolivia R. R., a distance of 60 miles. This railroad is well equipped and well operated, and its location among the mountains surrounding Uncia represents excellent engineering skill. In fact all of the railroads, although they are of only a meter gage, are remarkable for the excellence of their construction, the arrangement of their dining and sleeping cars and the precision of their operation. There is only one drawback to rail- road and hotel accommodations and that is the absence of heating facilities, which does not seem to affect the natives but keeps a tenderfoot&apos;s teeth chattering continually. The company is a consolidation of the Patiño company, owning properties at Uncia, with the Compafiia Estanfera de Llallagua, a&apos; Chilean corporation owning contiguous properties at Llallagua. Before the consolidation these companies were deadly enemies, and there still remain at the surface plant at Uncia the fortifications and underground defences provided during the warfare between the two factions. Also, in the Azul, or "Blue" tunnel at the junction line between the two properties is a strong steel barricade still bearing marks of the bullets fired during the various armed tilts between the workmen of the two companies. The headquarters for the mining operations and the milling plant have been moved since the consolidation from the original location at Uncia to the Llallagua side of the mountain, where the Chilean company&apos;s operations were carried on. The historic old town of Uncia, with its massive stone buildings of Spanish design, is a wreck, while the Llallagua side is being rapidly built up with modern structures.

Jan 1, 1929

By S. S. Shen, M. J. Pool, P. J. Spencer

Heats of solution of silver and copper in dilute Ag-Cu-Sn alloys at 720°K have been determined using a liquid metal-solution calorieter. Values of the se2f-interaction coefficient n AgAghave been calculated at constant copper concentrations and n Cu Cuhas been determined at constant silver contents. The reliability of the experimental data is shown by the very good agreement between nCujAg and ij &$; these interaction coefficients have experimental values of -9100 and - 9590 cal per g-atom, respectively. Certain solution models are shown to be inadequate for prediction of solute interaction coefficients in dilute Ag-Cu-Sn alloys. In a previous publication&apos; the results of a thermody-namic study of dilute Ag-Au-Sn alloys were presented. The present work represents the continuation of a program to investigate dilute alloys of the noble metals with tin and in particular is concerned with solute interactions in the Ag-Cu-Sn system. By determination of the magnitude and sign of the various interaction coefficients in dilute alloys it is possible to gain some understanding of the different types of solute-solute and so lute-solvent bonding changes that occur as the solute concentrations are varied. Hence systematic studies of alloys with similar physical characteristics as regards size, structure, electronegativity, and so forth, of their components can contribute a great deal to present theoretical knowledge of solutions. The recent definition of an enthalpy interaction coefficient, 11, by Lupis and Elliott2 is of particular value in calorimetric studies such as the present one: where j and i are solutes and s is the solvent; Si is the relative partial molar enthalpy of component i and x represents the mole fraction of solute or solvent. Values of ?Hi can be obtained directly by solution calorimetry and data for n are thus easily determined, often with a high degree of accuracy. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hi and to the enthalpy interaction coefficients by the expression: ?Hi?Hi + X;nz+ ... [2] The aim of the present work was to determine the self-interaction coefficients n AgAgand 178: in alloys of different compositions and also to establish values for n Agcg| and ncuAg. Since it is a thermodynamic requirement (resulting from the Maxwell-type relationships which can be applied to partial molar properties) that nAgcu and ncuAg should be equal, a further aim of this study was to demonstrate the agreement between experiment and theory. EXPERIMENTAL A description of the liquid metal-solution calorimeter used in this research has already been published,3 and no further details of its construction and operation will therefore be given here. Copper supplied by the American Smelting and Refining Co. was indicated by them as being 99.999 pct pure, and the silver obtained from A. D. Mackay, Inc., was also quoted as being 99.999 pct pure. A solvent bath consisting of between 70 and 80 g of 99.99 pct pure Sn was used for each series of experimental drops. Its weight was accurately determined and the appropriate amounts of copper or silver were added to give alloys of the desired composition. Approximately 0.00125 g-atom additions were used for determinations of the heat of solution of silver in the bath, while, for copper, specimens consisting of approximately 0.0015 g-atom were used. The heat capacity of the bath was determined at regular intervals during a series of drops using tin or tungsten calibration samples. The heats of solution of silver and copper in pure tin were first determined as a function of their concentration in order to establish the self-interaction coefficients 7AgAg and ncucu Alloys containing a constant 0.01, 0.02, 0.03, and 0.04 mole fraction of copper were then used to study 17:: in alloys of different copper content, while alloys of the same mole fractions of silver were used to determine equivalent data for 178: at constant silver concentrations. The composition of the bath was held at the desired copper or silver concentration by making calculated additions of the appropriate solute throughout the experiment. From the limiting values of ?HAg in the constant copper content alloys it was possible to study ?HAg as a function of xCu and hence to determine 42:. A similar analysis of the re, values permitted calculation of nAgcu. Heat content and heat capacity data from Hultgren et al* were used to calculate heat of solution values from the measured heat effects at the experimental temperature of 720°K. RESULTS AND DISCUSSION Determinations of ?HAg. A preliminary investigation of the heat of solution of silver in pure tin at 720°K was first made in order to establish the value of nAgAg before additions of copper were made and also to compare the value of ?HOAg(l) with that obtained in the previous study of Ag-Au-Sn alloys.&apos; Then the heat of solution of silver in Cu-Sn alloys was investigated as a func-

Jan 1, 1970

By John C. Bilello

The brittle fracture behavior of cold-worked sintered tungsten was studied over the temperature range 4.2° to 298°K using a high-sensitivity strain measuring system and electronfractography. Similar observations were made on a swaged electron beam zone-refined monocrystal. In sintered tungsten irreversible plastic deformation was observed during cyclic load-unload tests at stress levels well below the fracture stress for all temperatures, but general microyielding could be detected only down to 202°K. For the zone-refined samples macroyielding occurred at all test temperatures with evidence for twinning below -202°K. The fracture stress of the sintered tmgsten was virtually independent of temperature, while the zone-refined crystal showed a 2.3 times increase over the same temperature range. Electronfractography confirmed the presence of numerous rod-shaped and spherical submicroscopic voids which ranged in diameter from 1400 to 4300A in the sintered tungsten; no voids could be found in the zone-refined tungsten. Contrast effects observed on the replicas in the vicinity of certain voids indicated that plastic deformation could be induced by the local stress concentration. It has been suggested that the presence of these voids may be responsible for the low-temperature brittle failure of sintered tungsten. Based m this suggestim und on the evidence obtained here, a dislocatim model is presented to account for the brittle behavior of sintered tungsten. In this model slip, which is induced by the local high stress concentration in the region at the edge of a favorably oriented void, could cause the void to grow to a microcrack of critical size. STUDIES of brittle fracture in bcc metals have led to the well-known experimental relationships between grain size, yield stress, fracture stress, and temperature which have formed the basis for the various dislocation pile-up1-3 or interaction4&apos;= models for slip-induced microcrack nucleation. While microcracks can be nucleated by deformation twins,6,7 there has been no direct evidence furnished by transmission electron microscopy to support conclusively either the Zener pile-up or Cottrell dislocation reaction models for producing micro-cracks in all "brittle" materials. In addition to the "inverse" grain size relationship for yield and fracture stresses the cottrel14 theory predicts that the fracture stress below the transition temperature should behave in a fashion similar to that of the yield stress above this temperature. Such behavior has been verified for several bcc metals.8-10 With reference to both grain size effects and the tem- perature dependence of the fracture stress below the transition temperature, the behavior of sintered tungsten appears anomalous. Early work by Bechtold and Shewrnon 11 showed no apparent temperature dependence of the fracture stress below the ductile-brittle transition temperature (DBTT). They attributed this result to the intergranular nature of the fractures observed. More recent work by Wronski and Four-deux12&apos;13 on considerably purer material did not show any systematic relationship between the fracture stress and temperature below DBTT. The dependence of flow and fracture stresses on grain size is also not clearly established for sintered tungsten. Koo, for example, has shown that the DBTT for sintered tungsten depended chiefly on the annealing temperature and was relatively insensitive to the actual grain size achieved. Using electrofractography and transmission electron microscopy, Wronski and Fourdeuxl3 showed that numerous spherical and rod-shaped submicroscopic voids could be found in sintered tungsten but not in melted tungsten of nominally the same purity. They suggested that these voids could be responsible for the temperature insensitivity of the fracture stress below the DBTT. In the present work the temperature dependence of the fracture stress for high-purity commercially sintered tungsten has been determined. The presence of submicroscopic voids in sintered materials was confirmed, and these were studied in detail to examine the role they could play in nucleating brittle fracture. A dislocation model is suggested which could cause an inherent spherical void to lengthen into a Griffith crack of critical size. EXPERIMENTAL PROCEDURE Commercially sintered tungsten rod was obtained in the as-swaged condition from Sylvania. A zone-refined crystal was obtained from the same source. This crystal was grown by giving three zone passes (at 25.4 cm per hr) to a sintered rod of high-purity tungsten. The rod axis prior to cold working was -15 deg from the [110] direction. Originally the zone-refined rod was -6 mm in diam; it was reduced to -3 mm by eight swaging passes, at high temperatures, with each step having about the same reduction of area. The final swaging step gave a 7.5 pct reduction of area at 1050°C. All swaging operations were performed in a hydrogen atmosphere. For the sintered rod a similar working schedule was employed. Metal-lographic examination of the sintered material revealed that the cold-worked structure had an apparent grain diameter of -25 u transverse to the swaging direction (obtained by the intercept method). In the longitudinal direction cold-worked grains were approximately 1.5 to 2 times their diameter. No distinct fiber structure could be observed optically for the zone-refined rod. The cold-worked structure in the

Jan 1, 1969

By A. E. Jenkins, O. C. Roberts, D. G. C. Robertson

Using an inverted-cone coil at 450 kHz, it has been possible to levitate iron (FeS), cobalt (CoS), and nickel (NiS) sulfides. Important nontransition metal sulfides such as ZnS, PbS, and Cu2S have proven impossible to levitate although Cu-Fe-S ternary alloys containing 30 wt pct S and up to 10 wt pct Cu, and Cu-Co-S and Cu-Ni-S ternary alloys containing 30 wt pct Cu have been levitated. The levitation technique has been used in preliminary experiments on the vaporization from liquid sulfides and the reaction of liquid metal-sulfur alloys with oxidizing atmospheres. The course of the reactions with pure oxygen were followed using highspeed photography and two-color pyrometry. ELECTROMAGNETIC levitation is now established as a basic laboratory technique in high-temperature research but its application has been restricted mainly to metals and alloys. Applications have included alloy preparation,&apos; metal purification,2&apos;3 determination of liquid metal densities and emissivities,4,5 and studies of metal supercooling,4 alloy thermodynamics,6 and vaporization phenomena.7-9 The application of the technique to compounds has not been considered previously. The successful investigation of the reactions between dilute iron alloys and oxidizing atmospheres10&apos;1 has prompted the current physico-chemical studies involving levitated metal sulfide drops and flowing inert or oxidizing atmospheres. This paper presents the results of such a study and provides a basis for future studies involving a wide range of other compounds of metallurgical interest. The successful levitation of many metal sulfides and mattes provides a method of studying the oxidation reactions fundamental to flash-smelting and similar pyrometallurgi-cal operations under closely controlled laboratory conditions. In addition the system allows the use of a controlled atmosphere (e.g., a gas stream of a certain H2/H2S ratio) with a particular chemical potential to study the relevant thermodynamic equilibria or the mass transfer processes between the atmosphere and the levitated drop under conditions where the hydrodynamics of the system can be closely defined. The optimum frequency for the levitation melting of metals in an inverted-cone coil type inductor is within the radio frequency range 400 to 500 kHz. At frequencies lower than 10 kHz the rate of heat generation is usually insufficient to melt the levitated charge&apos; or where melting is achieved, "dripping" from the charge is encountered.&apos;&apos; At frequencies above 2 mHz the levitation force decreases. Metals, alloys and preheated elemental semiconductors such as germanium and silicon, have been levitated but the levitation of only a few metal compounds has been reported. Jostsons13 and the authors have levitated liquid titanium-oxygen alloys containing 50 at. pct 0 while clark14 has reported the levitation of mixtures of FeS and MnS for short periods. With a "cold crucible" inductor sterling15 has melted ferrites by preheating them by induction in a 4 mHz field and melting at a lower frequency. However this second type of inductor has been designed purely for the melting of materials without contamination; there is only a small gas film between the charge and the inductor and the electromagnetic levitation effect is of secondary importance. For this reason further discussion will be restricted to the use of the coil type inductor. The assessment of the suitability of a particular metal compound for levitation is based upon the following two criteria: i) thermal stability, and ii) physical "levitability". In this paper these two criteria will be considered separately. The thermal stability of a solid or liquid metal compound with respect to a gaseous environment depends upon its chemical reactivity with that environment or, in the case of an inert atmosphere considered here, its volatility. The physical criterion as to whether or not a particular compound can be levitated is based upon a comparison between those physical properties of the compound determining "levitability" which are defined by the fundamental equations of levitation theory as developed by Okress et a1.,16 and the properties of the metals. Since it is not practical to cover the vast field of metal compounds, further discussion will concentrate on the metal sulfides but the treatment would be applicable to any metal compound. THE THERMAL STABILITY OF METAL SULFIDES The temperatures usually encountered during levitation in inert atmospheres cover the range 1400" to 2000°C. The stabilities of the condensed states of the sulfides under these conditions are considered in relation to the periodic classification by reference to Table I. Two general classes of sulfides emerge. The solid sulfides of elements of group IIB and of groups further to the right are volatile while those sulfides of group IB and of groups further to the left are nonvolatile solids. The sulfides described as volatile may be dismissed as unsuitable for levitation. The stabilities of the more favorable nonvolatile sulfides under the anticipated conditions must be studied more closely From Table I it is seen that the alkali metal sulfides exist as liquids in the temperature range of in-

Jan 1, 1970

By H. H. Kellogg

Equations representing the standard free energy of formation as a function of temperature, for thirty metallic chlorides, are presented and plotted on a free-energy vs. temperature diagram. The use of these data for calculations on reduction of metallic chlorides, refining of metals with chlorine, and chlorination of metallic oxides and sulphides is illustrated. CHLORINE metallurgy&apos; has attracted metallur- gists for more than a century because the unusual properties of the metallic chlorides—low melting point, high volatility, and ease of formation from the oxides—make possible many useful extractive processes. Interest in chlorine processes is undergoing a renaissance due to present availability of chlorine at relatively low prices, and to recent advances in technology. During the present century there have accumulated a considerable number of reliable values of the thermodynamic constants for the metals and their chlorides. These data permit the calculation of free-energy equations for many metallurgically important reactions. Consideration of free-energy values makes possible certain predictions of the direction and extent of a given reaction, as well as the effect of temperature, pressure, and composition upon the result. Reaction rate, although not predictable from free-energy data, is usually sufficiently great at elevated temperatures that diffusion of the reactants and products to and from the zone of reaction determines the actual rate. Thus, if the free-energy indication is favorable, the chances are good that a high temperature metallurgical reaction will proceed at a reasonable rate, if adequate provision for rapid diffusion has been made. This paper presents standard free-energy equations for a number of metallic chlorides, based on data which are scattered throughout the literature. The equations are presented in a form that simplifies their use, and typical examples are given of the application of free-energy data to metallurgical processes. Free Energy of Reaction The free-energy change (AG) of a reaction is the true measure of the "driving force" of the reaction under a given set of conditions, and this is related to the standard free-energy change (AGO) of the reaction as follows: For the reaction: bB + cC = dD + eE ?G = ?G°+RTln ADd. AEA / ABb. ACc where A, = activity of constituent (i) T = absolute temperature, OK R = gas constant The criterion of a spontaneous reaction from left to right, at constant temperature and pressure, is a negative value for the free-energy change (?G). The standard free energy of the reaction is equal to the free energy of the reaction when all the reactants and products are at unit activity, since under these conditions the second term on the right-hand side of eq 1 is equal to zero. The concept of activity is treated fully in many textbooks on chemical thermodynamics1 and in a recent article by Chipman.2 Briefly, the activity (A,) of a constituent (i) is a measure of the reactivity of this constituent relative to its reactivity in some arbitrary standard state. For liquids and solids the standard state most often used is the pure liquid or solid constituent. Thus the activity of a pure liquid or solid in a metallurgical reaction is equal to unity. Gases under moderate pressure and at elevated temperatures behave very nearly as &apos;idea1 gases,&apos; and the standard state is chosen as the gas at 1 atm pressure. The activity of an ideal gas is therefore equal to its partial pressure, and this relation is sufficiently exact for real gases in most metallurgical reactions. For a liquid or solid solution there is in general no simple way to express the activity of a constituent as a function of its concentration, and activity must be determined by experiment. A few solutions follow a so-called &apos;ideal&apos; behavior, and if the pure constituent is chosen as the standard state, the activity of a constituent in an ideal solution becomes equal to its mol fraction. When a reaction reaches a state of thermodynamic equilibrium at constant temperature and pressure, AG becomes equal to zero and eq 1 reduces to: [ADd . AEe ?G°=RTln Abb ¦ Ac c equilibrium [2] The brackets surrounding the activity term are used to emphasize that each of the activities is an activity under equilibrium conditions—not just any arbitrarily assigned value. The bracketed term is the equilibrium constant (K) of the reaction. Eq 2 makes possible the calculation of equilibrium activities for a given reaction, if AGO is known at the desired temperature. The standard free-energy equations presented in this paper were calculated from the fundamental thermodynamic values of enthalpy of formation at 298°K (AH°,), standard entropy at 298°K (So298), heat capacity as a function of temperature (Cp), and enthalpies of transition, fusion, vaporization, and sublimation for the various constituents. Where possible the data reported in the recent "Selected Values of Chemical Thermodynamic Properties," published by the Bureau of Standards," were used. A large number of data came from the publications

Jan 1, 1951