Search Documents

By M. Prats

This paper presents a method for obtaining the correct values of the breakthrough sweep efficiency of the staggered line drive, taking into account the proper shape of the breakthrough streamline. Results obtained were different from those previously published, which were obtained by using an inexact shape of the breakrhrough streamline. INTRODUCTION In Section 9.31 of Muskat's' The Flow of Hotnogeticous Fluids Through Porous Media, it is stated that in a staggered line drive flood "the streamline of highest average velocity [is] the line of centers between input and output wells" (see Fig. I). Muskat used this concept to determine the relationship between the breakthrough sweep efficiency and the geometry of the staggered line drive pattern. Although it is clear from symmetry considerations that the breakthrough streamline passes through the midpoint between input and output wells, it is equally clear, as shown in Fig. 239 of Ref. 1, that the breakthrough streamline is not represented very well by the straight line joining the input and output wells. Therefore, it is desirable to determine the proper relationship between the breakthrough sweep efficiency and the pattern geometry by using the proper shape of the breakthrough streamline. METHOD OF SOLUTION It was found that the effect of the geometry of the staggered line drive on the breakthrough sweep efficiency can be investigated easily by making use of the method developed in Ref. 2. With this method, it can be shown that the general complex potential for the staggered line drive, which can be considered as a rectangular five-spot, is given in the coordinate system of Fig. 1, by O(z) = In cn(z\m) = +(x,y) + i $(x, y) . (1) where z = x + iy, +(x, y) is the potential distribution and $(x, y) is the stream function. The function cn (zm) is a Jacobian elliptic function of parameter m and has simple zeros at z,. = (2n + 1) K + 21iK and simple poles at z, = 2nK + (21 + 1)iK. Thus, the complex potential behaves like a(z) = ln(z - zr.) in the neighborhood of the production wells and behaves like a(z) = - ln(z - Z,) in the neighborhood of the injection wells. Since (z - z1.v) = rll.ei, we note that the potential + has the proper logarithmic behavior near the two wells, while the stream function $ varies with the angle, decreasing clockwise around the production well and increasing clockwise around the injection well. The functions K(m) and K'(tn), related by K(m) = K'(m,), where m + m, = 1, are known as the complete elliptic integrals of the first kind. By use of other properties of the Jacobian elliptic functions, the general stream function distribution for the staggered line drive can be obtained from Eq. 1: From the Jacobian elliptic function values, sn(0lm) = 0 dn(O(m) = cn(0jm) = 1, and f[K'(m)Iml = 03, it follows that the stream function given by Eq. 2 satisfies the proper symmetry conditions near a production well P located at [K(m), 01 and an injection well I located at [0, K' (m)]. That is, the line IOP in Fig. 1 is a streamline with value G (0. 0) = -0. and the straight lines connecting I and P to the point [K(m), K' (m)] is a streamline of value $[K(m), K' (m)] = -7/2. Similar symmetry conditions are obtained near other wells. It should be nuled that for m = m1, = 0.5, Eq. 2 reduces to the stream function distribution of the regular five-spot given in Ref. 7. SHAPE OF THE BREAKTHROUGH STREAMLINE It is apparent, from symmetry considerations, that the breakthrough streamline ($,) passes through the point [K(m)/2, K' (m)/2]. Its value there is so that the shape of the breakthrough streamline $,, is given by

Jan 1, 1957

By T. D. Yensen

Discussion of the paper of T. D. YENSEN, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 483 to 512. JOHN A. MATHEWS, Syracuse, N. Y.-Concerning the critical composition of the steel containing 2.50 per cent. of silicon, I may say that 12 or 13 years ago we made some of these alloys. They. were not as pure as the alloys made by Mr. Yensen, nor were they melted in vacuo, but one of them contained exactly 2.50 per cent. silicon, and about 0.25 per cent. carbon. It gave us no trouble whatever in hammering to a billet or rolling into bars, nor even when rolling into ¼ -in. wire rods. The steel in question was practically free from everything except carbon or silicon and contained no manganese sulphur or phosphorus worth mention. The alloy containing 2.50 per cent. of silicon worked perfectly well, as well as one containing 0.5 per cent. silicon, and it seems to me that further work should be done by Mr. Yensen on the physical properties of alloys at this seemingly critical change point. W. E. -RUDER, Schenectady, N. Y.-We -have made silicon steels of practically every composition and have never obtained any material under 5 or 6 per cent. of silicon which was brittle. This may be due, of course, to the presence of carbon, in some of the 'commercial materials, and I presume that Mr. Yensen would argue that the: presence of this carbon might prevent inter-granular brittleness. However, all of our silicon steels, up to 5 per cent. of silicon, by treatment in hydrogen at temperatures near the melting point, can be made to show inter-granular brittleness. Furthermore, the material made brittle in this way could be restored by treating at the same temperature in hydrogen containing a hydrocarbon vapor. I discussed this matter some years ago in a paper on inter-granular cement. It therefore appears likely to me that Mr.

Jan 5, 1916

By John F. Abel

In Silver Plume, Colo., there is a bachelor miner who offers individualized tours of his mine, The Silver Cloud. It is an interesting tour because he drove the mine himself and the view from the shack up there is spectacular. Beside that, he will probably invite you into his kitchen to sit around the old cook stove and drink coffee. When Andy first started his tour business he put a sign on the main street to advertise the fact. The sign read in part: "Women not welcome, but they will be tolerated at $3.00 a head”- the usual fee is $2.50. The sign lasted about 48 hours. Andy had to take it down because "all the ladies in town got mad at me. Now I take them all for $2.50 right across the board," he says. The mining industry is not only reticent about hiring women but traditionally does not even permit women to enter some mines. It would appear, what with the recent action on an equal-rights-for- women amendment in Congress, that we may be wise to examine the prospect.

Jan 1, 1970

By W. M. Morris

THE volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrell1 measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0° to 130° F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70° to 250° F. The specific volume in the gas and liquid region was determined at pressures up to 3000 lb. per sq. in. ? throughout this temperature interval. In addition, the vapor pressures were measured at 30° intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0° and 250° F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100° and 460° F. was carried out with apparatus that has been described in another paper (A.I.M.E. Tech. Pub. 1127).

Jan 1, 1939

By M. D. Banus, M. B. Bever, A. K. Jena

The heals of formation at 78", 195, and 273°K of the ternary compound h3SbTe2 based on the elements and based on the binary compounds In Sb and [inTe have been measured. The heats of formation at these temperatlcres of the binary compounds In Sb and In Te based on the elements have also been determined. Heal contents and free energies of the three compounds have been calculated from 0° lo 80I)°K. The free energies of joyrrzalion, heats of formations, and entropies of formation at 298°K have also been calculated. The results shown that the tertnary compound is metastable with vespecl to InSh and ln Te below 696 °K. bul is slable above that temperature. The weaker bonding of results in a positice entropy of formation which with incrensirzg temperature makes increasing negative conlvihtclions to the free energy and above 696°K renders the compound slable. THE ternary compound In3SbTez occurring in the quasi-binary system In Sb- In Te' forms on cooling at 829°K by a peritectic reaction.' Observations at 673" and 573 K have shown that this ternary compound decomposes slowly into the binary compounds InSb and1n~e.l'' It has not been possible to analyze the metastable behavior of the ternary compound because up to the present time data on its thermodynamic properties have been lacking. Some information on the binary compounds, however, is available. The heat of formation of InTe at 273°K and its free energy at 673°K are kn~wn.~'~ The heats of formation of InSb at 78", 273', 298", and 723°K have been measured5-' and its heat capacity between approximately 12" and 300"Kg9l0 is also known. In the investigation reported here the heats of formation at 78% 195% and 273°K of the ternary compound In3SbTez have been measured. The heats of formation of the binary compounds InSb and InTe at these temperatures have been obtained by combining new calorimetric results with previously published data. The heat contents and free energies of the three compounds at various temperatures from 0" to 800°K have been calculated. Against the background of this information, the metastability of the ternary compound will be discussed. 1) EXPERIMENTAL 1.l) Preparation of Specimens. The materials used consisted of the elements indium, antimony, and tellurium, the binary compounds InSb and InTe, and the ternary compound In3SbTez. The elements, obtained from American Smelting and Refining Co., had a nominal purity of 99.999+ pct. The compound InSb was Cominco semiconductor grade; the compound InTe was prepared from the elements by melting under a vacuum of 10-h m Hg followed by slow cooling. Three batches of specimens of the compound In3SbTez were used. One batch was prepared by melting appropriate amounts of the elements in an evacuated and sealed Vycor tube. The melt was held at approximately 100°K above the liquidus for about 8 hr, shaken repeatedly, and quenched into a mixture of ice and water. The specimen was annealed in vacuum at 760°K for 4 weeks. In preparing a second batch, a mixture of the component elements was melted and quenched in water. The resulting ingot was powdered. The powder was pressed into pellets, which were annealed in vacuum at 748" to 773°K for 4 weeks. A third batch was prepared in the same manner as the second, except that the starting materials were InSb and InTe rather than the elements. Metallographic examination of samples of the three batches and X-ray diffraction examination of a sample of the second batch did not reveal evidence of microsegregation or a second phase. The results obtained with the three batches showed no systematic differences. 1.2) Calorimetry. The calorimetric method has been described in detail." Samples of the compound In3SbTez, mechanical mixtures of InSb and InTe in the proportion of 1:2, and mechanical mixtures of indium, antimony, and tellurium in the proportion of 3:1:2 were added to a bismuth-rich bath at 623°K in a metal-solution calorimeter. These additions were made from 78°K (liquid nitrogen), 195°K (dry ice and acetone), and 273°K (ice and water). The heat effects of the additions were measured. The difference in the heat effects of the additions of a compound and the additions of the mixtures of its constituents, adjusted for differences in the concentration of the bath, is the heat of formation of the compound. In the concentration range not exceeding 1.5 at. pct solute, the heat effect of the additions was a linear function of concentration. The heat of formation refers to the temperature from which the additions were made, namely, 78", 195", or 273°K. Several calibrating additions were made in each calorimetric run. The calculated heat capacity of the calorimeter and hence the calculated heat effects of the additions of samples depend upon the values adopted for the heat contents of the calibrating substance. In this investigation bismuth at 273°K was used and a value of 4.96 kcal per g-atom was taken for (HGZ3"k . 2) RESULTS AND DISCUSSION 2.l) Heats of Formation. The heats of formation of the ternary compound In~SbTez from the component elements indium, antimony, and tellurium and from

Jan 1, 1968

There were present eleven Directors, the Secretary and Assistant Secretary of the Institute, and eleven guests. The Secretary, Bradley Stoughton, was appointed the representative of the Institute on the Board of. Directors of the American Bureau of Welding. A communication from a member of the Institute regarding simplified spelling was laid on the table. The following appropriations were made for the year. 1919: $250 to the Institute of Metals Division, $250 to the St. Louis Section, $100 to the Columbia Section. An invitation was received from the Western Society of Engineers to the Institute to use the facilities of that society during the A. I. M. E. Meeting in Chicago. The Bulletin of the Institute was presented to the French Congress of Engineers. There were elected twenty-eight members, eighteen associates, and three junior associates. The status of one member was changed from junior associate to associate. Four members were reinstated. An extension of time was granted to one member for payment of dues. The dues of four members on active military duty were suspended. Dues were remitted of four members who have been paying over thirty years, and who are each over seventy years of age.

Jan 5, 1919

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970

By Louis Raymond, John E. Dorn

The object of this investigation was to analyze the recovery that arises when the stress on a specimen undertaking creep is reduced. For this purpose annealed specimens of high-purity aluminum were precrept under a stress of 1000 bsi to a strain of 0.08 following which the stress was reduced for various periods of time to 10, 250, 500, or 700 psi. When the original stress was reapplied the subsequent creep curve lay above that for the unre-covered state and below that for the original annealed state. Analyses on the kinetics of this recovery as a function of the temperature gave a stress-sensitive activation energy that decreased as the reduced stress was increased from a value of 64,000 cal per mole at 10 psi to 37,000 cal per mole at 750 psi. Recovery was also detected and measured during creep under the reduced stress. Following a short initial period, the creep rate under the reduced stress increased monotonically until it reached the secondary-creep rate for the reduced stress. The temperature dependence of this phenomenon was also shown to be correlatable in terms of the previously deduced activation energy for recovery. The activation energies for creep of most pure metals at high temperatures have been shown to agree well with those for self-diffusion.&apos;j2 Since the true secondary stage of creep is usually due to the steady-state balance between the rate of strain hardening and the rate of recovery, it is generally thought that the activation energy for recovery of the creep-induced substructure equals that for creep itself. A shoft time ago, however, Ludemann, Shepard, and Dorn~ found that the activation energy for recovery of the creep-induced substructure in high-purity aluminum under zero stress was almost twice that for self-diffusion, namely about 65,000 cal per mole; obviously recovery under reduced stresses differs in some significant way from the recovery that accompanies the secondary stage of creep. The major purpose of this investigation is to study the effect of stress on the re- covery of the creep-induced substructure in order to provide a better understanding of the recovery mechanism itself. EXPERIMENTAL TECHNIQUE High purity aluminum, containing 0.004 pct Cu, 0.002 pct Fe, and 0.001 pct Si, used in this investigation, was in the form of 0.100-in.-thick sheet which has been cold-rolled to the H-18 temper. Creep specimens were milled from the sheet with their tensile axes in the rolling direction. All specimens were then heated at 686°K for 1 hr followed by air cooling in order to produce an annealed structure which exhibited a uniform equiaxed grain size of about 4 grains per mm. Tests were run in creep machines fitted with Andrade-Chalmers type of lever arms so contoured as to maintain the stress constant to within 0.05 pct of the reported values. Constant temperatures to *O.l°K were obtained by complete immersion of each specimen in a temperature-controlled and agitated bath of molten KN02-KNOs mixture. Where changes in temperature were involved, the change was effected in less than 2 min by manually replacing one bath by another controlled at the second temperature. Displacements over the gage section were sensed by linear differential transformers, the output of which was autographically recorded. The calculated strain measurements were sensitive to 5x EXPERIMENTAL PROCEDURE The following analyses are based on extensions of the previously announced effect of the temperature on the creep strain,2 namely for a = constant, where e = the total true tensile creep strain for a given applied true tensile stress, t = the duration of the test, R = the gas constant, T = the absolute temperature, Q, = the activation energy per mole for creep which is independent of the stress, / = a function of 8, = and of the stress, and a = the stress. The validity of this correlation for high-purity aluminum is demonstrated in Fig. 1 for temperatures in the near vicinity of 600°K; the activation energy for creep, Q,, which is approximately that for self-diffusion, is insensitive to the applied stress

Jan 1, 1964

By AIME AIME

ASIDE from the annual dinner-dance, the two outstanding social events of the Annual Meeting were the dinner- smoker on Monday night and the informal dance on Tuesday night, both of which were held at the Commodore Hotel. Approximately 400 attended the former event, compared with 570 a year ago, and about 250, people were attracted to the dance.

Jan 1, 1933

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of &apos;InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of&apos; metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.&apos;-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.&apos; This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.&apos; A concurrent publication&apos;0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.&apos;&apos; Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By B. A. Kulp, R. R. Reeber

Lattice parameters for the wurtzite form of&apos; CdS mere measured by powder X-ray diffraction techniques over the temperature range 26° to 1000 K&apos;. A negative thermal -expansion coefficient was determined parallel and perpendicular to the c axis below 13.5°K. Near 808°K, the curves of the a, parameter, the differential thermal expansion, and the resistivitv vs absolute temperature exhibited a reversible discontinuity. j\. direct determination of the lattice parameters of CdS over an extended temperature range is of particular use in interpretation of the effects of high pressure on the band structure of semiconductor materials. For example, Langer&apos; has studied the effects of pressure on the absorption edge of CdS from 77°K to room temperature. In order to properly interpret his results it is necessary to know the change in lattice constants as a function of temperature for the wurtzite, zincblende, and rocksalt2 modifications of this material. Thermal-expansion measurements for CdS, wurtzite phase, have previously been determined over a limited temperature range.s74&apos;5 The zincblende phases, of other compounds with similar bonding, have been investigated by Novikova et a! .&apos;&apos; Previous thermal-expansion measurements for metals with hexagonal symmetry have for the most part used bulk sample techniques for low-temperature result. Most X-ray measurements at low temperature have been on materials with cubic symmetry.&apos;jQ The use of X-ray powder-diffraction techniques offers a convenient and accurate method of measurement over a wide temperature range. The X-ray method, besides measuring unit cell size, also provides information about change in structure type and the nature of some of the stacking defects present. I) EXPERIMENTAL PROCEDURE The thermal expansion was measured by X-ray powder-diffraction techniques. Lattice parameters for the range 300" to 1000°K were determined in a 19-cm Unicam camera. From 26" to 300°K a 34-cm back-reflection camera with the Van Arkel" film arrangement was used. The sample was bonded to a copper cold finger below a helium, hydrogen, nitrogen, oxygen, dry ice, or ice brine bath in a metal cryistat. che inner bath was surrounded by another one for radiation shielding. Nitrogen was used in this outer bath for the very low-temperature runs while dry ice and acetone was used for the 195°K point. CuKa X-rays, filtered with a nickel foil, entered the cryostat through a 0.001-in.-thick aluminum window. During a typical 9-hr exposure the sample was continuously rotated through a 30-deg arc. Heat losses from the sample holder limited the minimum temperature attained to 26°K with helium in the inner dewar. Temperature calibration between 25" and 125°K was determined with an Allen Bradley 300-ohm carbon resistor. The resistor was attached to the back of the copper finger with a thin layer of silicone grease. Liquid He, HZ, N2, and O2 baths were used to calibrate the resistor. Temperature variation is estimated to be *2"K with a slightly higher uncertainty at room temperature and 264°K. The thermal expansion of high-purity germanium from 373" to 900°K was measured as a calibration for the Unicam camera. This value was compared with the known value1&apos; for the thermal expansion. A discontinuity in the thermal-expansion coefficient of the CdS a, parameter was observed. Similar discontinuities in the resistivity and differential thermal analysis at the same absolute temperature indicate that the temperature error is *5°K in the temperature range above 500°K. Temperature errors in the Unicam camera below 500°K are appreciably higher due to large gradients in the resistance furnace. II) SAMPLE PREPARATION The CdS was Eagle Picher ultrapure grade. The crystallite size range of the as-received powder

Jan 1, 1965

By R. W. Gould, B. G. LeFevre, A. G. Guy

The resistivity anomaly known as the K state was studied in Ni-Mo alloys containing 10.5 and 14.0 at. pct Mo. Both these alloys exhibit a large K effect which depends on the mechanical and thermal treatment. On the basis of X-ray diffuse scattering studies which were correlated with resistivity measurements, it appears that the K state in dilute Ni-Mo alloys can be associated with changes in the degree of short-range order within the a phase. An interesting phenomenon that has received much attention in recent years is the K state. The K state is marked by anomalous changes in some of the physical properties of certain alloys without the occurrence of observable microscopic structural changes. One of the early pieces of work in this area was by Thomas&apos; who studied alloys of Ni-Cr, Ni-Cu, Ni-Cu-Zn, Fe-A1, Fe-Si, and Ni-A1. Upon annealing specimens which had been previously cold-worked or quenched from an elevated temperature he found an anomalous increase in resistivity over a certain temperature range. He also found that specimens which had been appropriately annealed to develop the K state showed a decrease in resistivity upon subsequent cold working. These effects are opposite to those found in normal alloys. Although the resistivity anomaly has been rather arbitrarily taken as the "definition" of the K state, there are several other interesting effects which accompany the resistivity increase. In Ni-Cr alloys,2, 3 for example, it was found that the hardness increases with increasing resistivity. It was also found that specimens which have been treated to develop the K state can be cold-worked for as much as an 80 pct reduction of area without an increase in the hardness. In Fe-A1 and Fe-Si alloys4 the K state is accompanied by an increase in flow stress and by a lattice contraction. In Ni-A1 alloys,5 specimens which have been treated to develop the K state also show an increase in elastic modulus. In Ag-Pd alloys6 the increased resistivity observed on annealing a cold-worked specimen is accompanied by an increase in the thermoelectric power and an increase in the Hall coefficient. The explanations of the K state phenomena are varied and depend upon the particular alloy in question. Several theories have been advanced to explain the increased conductivity with cold work on the basis of changes in the electronic configuration of the alloy as a result of local lattice distortions.7"9 Most investigators, however, believe that some type of local order in the solid solution, either short-range order (SRO) or clustering, is responsible for this effect. Theories concerning the relationship between ordering and the K state have for the most part been speculative, since there is little direct X-ray evidence that can be correlated with the above property changes. Much of the previous work on the K state was done in the Ni-Cr system where the small difference in the X-ray atomic scattering factors of the components nickel and chromium makes it very difficult to use X-ray diffuse-scattering measurements to determine the role of local order. In the Ni-A1 system, however, Starke et al.10 succeeded in detecting a connection between local order and the K state. It was found that a small but measurable K effect correlated with increasing SRO in the nickel-rich a phase. The manner in which local order might increase the resistivity of K state alloys is not completely clear. Since most of the known K state alloys contain at least one transition element, significance has frequently been attached to the presence of an unfilled d shell. It has been suggested that during the formation of the K state the number of conduction electrons decreases as a result of the transfer of s electrons to the d shell where they are more tightly bound.1&apos;11&apos;12 Koster and Rocholl13 have proposed that SRO can cause an increase in resistivity for alloy systems in which the number and mobility of charge carriers are reduced when the percent solute is increased. According to this hypothesis, the local environment of a given solvent atom changes in the same manner with increasing percent solute as it does with an increasing degree of SRO; hence the change in physical properties should tend in the same direction. In this hypothesis, SRO is considered only in a statistical sense, and the increased resistivity of the K state is attributed to a change in the mean distribution of electrons and holes in the s and d states as a result of SRO. From the work of Chen and Nicholson on Ag-Pd alloys,6 it appears that the K state can occur in systems for which the d shell is completely filled. These investigators explained the increased resistivity by picturing the SRO as small domains of some form of long-range order (LRO). According to ~ibson,&apos;~ the number of effective electrons can be reduced by the creation of a new Brillouin zone boundary near the Fermi surface of an alloy as a result of the changing crystallographic symmetry that accompanies the formation of a superlattice. This idea may be expressed in terms of the superzone concept.15 In the present work the role of local order in the formation of the K state in Ni-Mo alloys was investigated. The principal tools used in this study were X-ray diffuse scattering and electrical resistivity measurements; however, these data were supplemented by electron microscopic and field-ion microscopic data. The purpose of the work was to determine whether or not the K state in Ni-Mo alloys can indeed be attributed to the formation of SRO as has been proposed by previous investigators.

Jan 1, 1969

By W. S. Pellini, F. N. Rhines

IN many of the otherwise well established alloy phase diagrams the solidus curves (temperatures at which liquid first appears upon melting) have not been located accurately, chiefly because the experimental techniques that have been most popular for determining solidus temperatures have been both cumbersome and subject to large errors. C. E. Homer and H. Plummer1 have described a sensitive and at the same time a very simple technique for locating the solidus curves in a number of alloys of tin. Their method consists simply in noting the temperature at which a specimen of the alloy ruptures under the influence of a light bending force. Although this method is not new, it has been little used for this purpose in the past; nevertheless, it appears so attractive in its possibilities of speed, simplicity, and precision that the investigations presently to be described were undertaken to verify its merits. The redetermination of the solidus and eutectic temperatures of the lead-antimony system was employed as a medium 0f experimentation. New values obtained in this way are believed to be sufficiently precise to warrant a revision of the currently accepted lead-antimony phase diagram (Fig. I). Determinations of the solidus of the lead-rich lead-antimony alloy series have been published by R. S. Dean2 and by E. E. Schumacher and F. C. Nix.3 Their points are represented in Fig. I. In their work the solidus was not located at antimony concentrations greater than 2 per cent; the curve was presumed to meet the eutectic horizontal at an antimony concentration of about 2.5 per cent. In the present studies the solidus has been traced to 3.5 per cent, where the eutectic horizontal is intersected (Table I and Fig. I). Within the range investigated by Dean and by Schumacher and Nix the agreement with their values is good. H. Seltz and B. De Witt,4 on the basis of activity measurements, have calculated that the intersection of the solidus and the eutectic reaction horizontal should lie at 3.86 per cent of antimony. The following determinations of the eutectic temperature have been reported: Roland-Gosselin,5 228°C.; Ewen,6 228°C.; J. E. Stead,7 247°C.; Campbell,8 228°C.; W. Gontermann,9 245° to 252°C.; R. Loebe,10 245°C.; E. Heyn and 0. Bauer,11 245°C.; H. Endo,12 250°C.; R. S. Dean,2 249° to 258°C.; E. Abel, 0. Redlich, and J. Adler,13 245°C.; W. Broniewski and L. Sliwowski,14 250° to 252°C.; H. Seltz and B. De Witt,4 250°C. A temperature of 249°C- appears to have been generally accepted in recent years; it is the value most frequently obtained by the method of cooling curves. Values below 249°C. have usually been obtained by inferior cooling-curve techniques; those above 250°C., by the method of heating

Jan 1, 1942

By John S. Crandall

Occurrence: small crystals in alluvial sands from the eroding Belt Series mica schists. Flowsheet: dragline, trommel screen, jigs, drier, crusher, screens. Value: ground, $2.50 per cu yd, garnet sand gross $60. per ton. Costs: production and sales $48. per ton. Uses: blasting sand in aircraft plants, monumental works, foundries. Efficiency comparison: superior to silica sand. Future: possibilities only touched upon, research continuing.

Jan 1, 1950

By Leon Dominian

Page I. Introduction......................237 11. Coal..................239 (a) Western Asia Minor.........239 I-. Lignites of the Marmora-Bgean zone.239 2. The Black Sea basin.............241 (b) Eastern Asia Minor..........244 (c) Syria................246 (d) Mesopotamia................ 246 (e) European Turkey.&apos;.....&apos;..... 247 111. Oil and Allied Hydrocarbons...............248 (a) Early Use of Oil and Bitumen in Turkey........248 (b) Syria........................ 250 (c) Mesopotamia.................... 250 (d) European Turkey.................. 256 I. INTRODUCTION Apart from local needs in the country&apos;s development, the interest attached to Turkish fuels grows chiefly out of the importance of the railway industry in Asiatic Turkey. Geographical conditions make of the tracks in this region the most essential link in a chain of world-girdling lines. By its position Asia Minor can be likened to a bridge in the through routes destined to connect European factories with Asiatic and African markets. An uninterrupted right-of-way from points in central Europe to populous Indian cities must necessarily pass through the valleys of Anatolia. Crossing thence the Taurus Mountains, its natural passage is indicated as the Mesopotamian lowland and the shores of the Indian Ocean. Similarly, land connection between Europe and Africa can be obtained only by passage through Asia Minor, Syria and Palestine. The occurrence of fuel within an area of such significance from the

Jan 1, 1917

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By W. K. Hardy, H. H. Stadelmaier, L. J. Huetter

The ternary system Co-Sn-C was studied in the cobalt-rich region. The liquidus projection ulas established and two fonr -phase reactions were found. An isothermal section at 950°C was worked out. In the region studied the following phases were observed: cobalt-rich solid solution, graphite, binary compound y -cobalt-tin, and a ternary compound. As a result of the limited solubility of carbon in liquid cobalt-tin alloys, the investigation was limited to the cobalt-rich region. Tin contents up to 32 at. pct were studied. Cobalt of 99.99 pct purity, tin of 99.97 pct purity and synthetic graphite of 99.93 pct minimum purity prepare the alloys. Carbon determinations of all alloys were obtained by gas volumetric analysis. Samples were investigated microscopically and by X-ray diffraction using CoK, and FeK, radiation. Cooling curves were obtained with a number of alloys to determine the temperature of the four-phase reactions. The thermocouple was calibrated with the melting points of high-purity silver and copper. In the region studied the following phases were observed: Cobalt-rich solid solution (face-centered cubic) Graphite. Binary compound y (solidifies congruently at composition Cop~n)&apos;. Ternary compound k which is face-centered cubic with superlattice and nonferromagnetic.&apos; In Fig. 1 the fields representing the projections of the liquidus surfaces were determined by microscopic investigation and are labled by their primary phase. In the field labled C graphite is the primary phase. During solidification in this field much of the primary graphite was expelled through the surface of the melt. It could not always be established microscopically whether the remaining graphite was primary or purely eutectic. Therefore it was not possible to determine accurately the boundary curve which drops from the binary eutectic el at 1309 "~~ to the point of the four-phase reaction at F. The ter-nary carbide is the primary phase in the field labled k. To the right of this field the primary graphite is consistently nodular whereas flake graphite is observed at tin contents somewhat below F. The ternary carbide does not appear to solidify congruently. The graphite is attacked in a peritectic reaction along the boundary between k and C. Thus no graphite is observed in alloys in the k field. In alloys right of the boundary between k and C the graphite nodules are located in the center of the k crystallites, further documenting the peritectic nature of the reaction with the graphite. A four-phase reaction was found at F and 1120 &3"C. The most likely reaction is L+ CY-Co + C — k. Below the temperature of the binary eutectic ez at 1112" a second four-phase reaction was observed at E and 1100 lt3"C. It is the ternary eutectic L — CY-Co + k + y. Figs. 2(a ) to (e) show microstructures of the ternary alloys in the as-cast condition. Fig. 2(a) shows the eutectic a-Co + C (with some primary graphite) with the carbide k in the grain boundaries. Fig. 2(b) shows primary cobalt (dark areas) and the eutectic a-Co + k which is formed along F-E.

Jan 1, 1961

By A. K. Jena, M. O. Bever

The thermodynamic behavior of dilute solutions of copper, silver, and gold in liquid tin is not explained by current solution theories.1-3 The relative partial gram-atomic enthalpies, or heats of solution, of silver, gold, and platinum in liquid lead at 623°K have been measured in the investigation reported here. Their interpretation requires a modification of the regular-solution theory although lead-rich solutions may be expected to be simpler than tin-rich solutions. The liquid metal solution calorimeter used has been described.4 At the start of a run the bath consisted of 621 g of reagent-grade lead. Several calibrating additions of lead were made during a run; a value of 3.48 kcal per g-atom5 was taken for H623°K - H273°K Two runs were made with each of the solutes silver, gold, and platinum. Annealed wire samples of 99.999+ pct purity were used. Four to six samples each weighing 0.5 to 1,0 g were added from 273°K to the bath at 623°K and the associated heat effects were measured. The samples dissolved in approximately 3 min. No serious experimental difficulties were encountered. The heat effects of the additions in a run plotted against the average atom fraction of solute before and after each addition314 were linear functions of the concentration in lead of silver, gold, and platinum, respectively. By subtracting the difference between the heat contents of a solute element at 623° and. 273°K5 from the measuredheat effects, the partial gram-atomic enthalpy relative to the solid solute was obtained. The relativ: partial gram-atomic enthalpy at infinite dilution and the concentration dependence of the partial gram-atomic enthalpies obtained from the plots of vs atomic fraction x are listed in Table I. The relative partial gram-atomic enthalpy at infinite dilution of silver in lead of 5.46 kcal per g-atom at 623°K compares with values at 723°K of 5.74&apos; and 5.765 kcal per g-atom. These data yield a temperature coefficient of 3.0 cal per g-atom-OK. The partial gram-atomic enthalpy at infinite dilution of gold in lead at 623°K is 0.89 kcal per g-atom compared with 0.85 kcal per g-atoms (obtained by extrapolation) and 0.95 kcal per g-atom.5 By combining these values for 623°K with those for several other temperatures5" the temperature coefficient of was found to be 3.2 cal per g-atom-OK. No thermodynamic data are

Jan 1, 1968

By D. D. Homer, R. H. Cromwell

The Minas de Matahambre No. 2 shaft, vertical, four-compartment lined with steel sets and hardwood lagging, has been sunk 2057 ft. On account of rock structure, over-all cross-section dimensions are 23 by 6 ft. Certain sections have been concreted. Two compartments are for handling ore and men, one for supplies and men, and one for manway, cables and counterweight. Two 250-ton capacity skip pockets with air-operated gates and steel cartridge pockets have been installed underground. A steel "A" headframe, a 250-ton steel receiving bin, and skip-to-man-cage changing equipment have been provided. Skip capacity is 102½ cu. ft. The hoist is a Nordberg double-drum 10 ft. by 6 ft. 6 in. geared, electrically driven, with parallel grooving for 1-?in. cables. Maximum hoisting speed is 1600 ft. per minute. The motor-generator set, control panel, slip regulator and hoist accumulator are housed in the basement of the hoist house. The electrical equipment is General Electric. The direct-current hoist motor is 800 hp. Control is of the Ward-Leonard-Ilgner type. The motor-generator flywheel set, normal speed 720 r.p.m., consists of an 800-hp. induction motor, a 22-ton flywheel (dia. 117 in.) and a 650-kw. generator.

Jan 1, 1934