Search Documents

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By E. P. Polushkin, Henry L. Shuldener

THIS paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. PIPES EXAMINED The pipes were made by different manufacturers and their sizes range from ¾ in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often 100 to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is 100° to 160°F. WATER SUPPLIES The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table I are characterized by relatively low hardness, low alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1944

By E. W. Johnson, M. L. Hill

Cold working of iron-carbon alloys was found to increase greatly the hydrogen solubility and to decrease the diffusivity at temperatures up to 400° C. These effects are increasing functions of both the carbon content and the degree of deformation. The hydrogen behavior is consistent with the idea that cotd working creates "traps", which are concluded to be microcracks in which the hydrogen is chemisorbed. Hydrogen embrittlement is explained by the Petch theory of metal crack surface energy loss due to hydrogen adsorption. HYDROGEN embrittlement of steel has been studied for many years and has been the subject of an extensive literature, but the mechanism of the effect has not been completely understood. The embrittlement is unusual in that the ductility loss is not accompanied by an increase of the yield strength, being primarily a decrease of the fracture strength alone. The loss of fracture strength is usually most severe in the temperature range between 0°and 100°C. Here the solubility of hydrogen in the iron lattice at ordinary H2 pressures is extremely low while the diffusivity is still quite high. From the relationships between the ductility and the hydrogen content, test temperature and strain rate, it is apparent that the hydrogen atoms causing the ductility loss difbse to and concentrate in small regions of the metal which are especially susceptible to the initiation and propagation of fracture. This hydrogen segregation apparently occurs after plastic straining has begun. Below 0°C the ductility loss persists only at low strain rates in confirmation of the view that the embrittlement is diffusion .controlled. The tendency of the embrittlement to disappear above 100°C can be explained by the increasing lattice solubility of hydrogen with rising temperature. A common view of hydrogen embrittlement of steel is that the hydrogen initially dissolved in the metal lattice diffuses to structural discontinuities and there precipitates as H2 gas at very high pressures which assist the external stress in causing premature failure.1,2 The idea of a high H2 pressure in equilibrium with ordinary amounts of hydrogen in steel at room temperature is due to observations of hydrogen behavior in fully annealed material, for which the Sieverts' law constant relating solute concentration to H2 pressure is extremely small. Hydrogen-embrittled steel, however, is always plastically deformed to some extent, and therefore it is important that hydrogen embrittlement be explained primarily in terms of hydrogen behavior in plastically deformed material. Such an explanation is attempted in this paper. Previous studies of hydrogen in cold-worked steel have shown that both the solubility and the diffusion rate are significantly chaned when the steel is cold worked. Darken and Smith discovered that the amount of hydrogen absorbed from acid by cold-rolled steel at 35°C is many times greater than that absorbed by hot-rolled steel. They found also that the hydrogen permeability of the steel is unaffected by cold working. Keeler and Davis4 confirmed the high apparent solubility of hydrogen in cold-worked iron-carbon alloys at temperatures up to and even beyond the recrystallization temperature. They also found that this solubility increase accompanying cold work is a sensitive function of the carbon content, being absent when no carbon is present. The present experimental study was undertaken primarily to obtain an improved understanding of the behavior of hydrogen in cold-worked steel. Data were obtained on the effects of temperature, H, pressure, carbon content, and degree of cold work on the hydrogen solubility and diffusivity in iron-carbon alloys. These data have been helpful in elucidating the nature of the cold-worked steel structure as well as in providing information on the mechanism of hydrogen embrittlement of steel. EXPERIMENTAL Cylindrical specimens for hydrogen absorption and diffusion rate measurements were prepared from three iron-carbon binary alloys and a commercial SAE 1010 steel. The iron-carbon alloys were prepared by vacuum melting electrolytic iron with graphite in a magnesia crucible. The alloys were cast in vacuum as 2 1/2-in. sq ingots weighing about 20 lb each. The ingots were hot rolled (above 1900°F) to 5/8-in.-diam round bars and then cooled in air to room temperature. The resulting metallographic structure consisted of islands of fine pearlite surrounded by free ferrite. Chemical analyses of the materials are given in Table I. The 5/8-in. diam bars were turned to diameters such that cold reduction to the desired final specimen diameters would result in either 30 or 60 pct reduction in area (RA). The machined bars were then cold worked by swaging at room temperature

Jan 1, 1960

By Albert Sauveur

This paper explains the possibility of using advantageously a boiling solution of sodium picrate to reveal dendritic segregation in steel. The mechanism of the action of the reagent is described. The failure of manganese alone to produce persistent dendritic segregation is also considered. IRON, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.1 For this purpose, a cupric solution, such as Le Chatelier's, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free., from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters, which represents the same spot as that shown in Fig. 1. The fillings

Jan 2, 1924

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915, Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semi- precious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1975

By M. J. Blackburn

The phasal equilibria in TI':Al alloys has been studied Ry transmission electron microscopy, electron diffraction, and X-ray diffraction. It is shown that three-phase fields exist below the transformation, viz.: a disordered hexagonal solid solution a; an ordered hexagonal phase based on Ti3Al, aa; and a two-phase region. (a + (YZ) , occurring between the single-plzuse fields. The size. disiribution, and morphology of- the a, phase in the two-phase region is shown to be dependent upon the alloy composition and heat treatement. The ordering process in the a, phase leads to the formation of anliphase domain boundary networks; the contrast and stability of these networks is shown to be dependent on alloy composition. A new and relatively simple phase diagralil for the systemm is constructed. The phasal equilibrium at the titanium-rich end of the Ti:Al system has long been the subject of considerable controversy. crossleyl has recently reviewed the phase diagrams that have been advanced for the system and in his turn proposed yet another one. There would seem to be general agreement that a phase exists at a composition at or near Ti& with an ordered hexagonal DO,,-type structure. However, several other phases have been proposed; for instance, Ence and ~ar~olin's' diagram includes two phases, Ti2A1 and Ti3A1, in the region up to 25 at. pct Al. The position of the proposed phase boundaries varies over a considerable compositional and temperature range, a point graphically illustrated in Fig. 1 of Crossley's paper.' It is perhaps germane to briefly examine the techniques used by other workers in the establishment of the phase structure. These fall into three categories: 1) X-ray diffraction, the only limitation of which is the rather low intensity of superlattice reflections in this system.3 Thus, superlattice reflections become increasingly difficult to detect in the more dilute aluminum alloys. 2) A considerable amount of optical microscopy has been performed"2'4 and it will be shown in a later section that many of the obscure mi-crostructures that have been observed can be attributed to hydrogen contamination. It is concluded, therefore, that such observations should be interpreted with considerable care. 3) The variation of some physical property with aluminum content has been measured.5"7 These methods are a useful indication of the existence of a transformation, but are usually insufficient in themselves to identify the transformation. The results using these techniques will be considered in more detail in the discussion. In this paper, the phase structure of alloys containing up to 25 at. pct A1 has been studied by transmission electron microscopy and X-ray techniques, and the results are used to generate a new and relatively simple diagram for the titanium-rich end of the Ti:Al system. EXPERIMENTAL A series of alloys containing 5.05, 10.16, 13.39, 13.99, 14.40, 20.83, and 25.05 at. pct A1 were obtained in the form of hot-rolled sheet 0.02 in. thick. These alloys contained 0.10 to 0.15 pct 0. Thirty-gram arc-melted buttons were prepared from iodide titanium and 99.99 A1 which contained 16.1, 16.9, 18.2, 19.0, 21.6, 22.2, 23.0, and 23.9 at. pct A1 and had an average oxygen content of 0.03 pct 0. The differences in oxygen content did not appear to influence the nature of the phase transformations which were found. Oxygen content may affect the temperature of these transformations, but insufficient samples of the high-purity alloys were examined to answer this question. The heat treatment of alloys was performed in dynamic atmosphere and vacuum furnaces or in helium -filled silica capsules. A special vacuum furnace was constructed to provide a high quenching rate in which rates of 4000°C per sec were obtained using water as the quenching medium. As pointed out by Crossley,' it is important to avoid heat treatment in the a - [} phase field as the resultant segregation of the alloy into the two phases containing different amounts of aluminum can persist through subsequent treatments leading to ambiguous results. It will be demonstrated later that step cooling of specimens from the a phase region can also lead to anomalous effects. Thus, all solution treatments were carried out in either the a or 3 phase fields followed by water quenching and subsequent isothermal annealing at various temperatures. X-ray analyses were performed on a diffractometer on fine-grained bulk specimens. The value of long-range order parameter, S, wa_s calculated from the integrated intensity of the (1211) reflection. In general, the intensity of the (1011) superlattice reflection was compared with that of the (2021) fundamental reflection to correct for experimental differences between measurements. Thin foils for electron microscopical examination were produced by electropolishing using the technique described in an earlier paper.8 Dark-field techniques were employed to a large degree in this investigation using the gun-tilt method. Finally it should be noted that the lattice parameters of the D01,-type superlattice are approximately related to the disordered hexagonal phase parameters by Crf - c, and 2ad - a, where the subscripts s and d refer to the ordered and disordered unit cells, respectively.

Jan 1, 1968

By Richard O. Carlson

Ions of p31 and B 11 were implanted in natural insulating diamond macles. The thin (-0.4µ) layers showed sheet resistances of 107 to 1011 ohm per sq and activation energies of 0.17 to 0.34 ev above room temperature. However, no Hall effect could be measured, indicating that mobilities were less than I to 10 sq cm per (v-sec). Such low mobilities may be due to excessive scattering due to radiation damage in the bombarded layer or to very high concentrations of active compensating impurities. Annealing did not materially change the room -temperature properties, but the temperature was limited to -800°C by surface graphitization, the latter process probably being accelerated by lattice damage in our diamonds arising from the ion bombardment. A weak n-type thermoelectric power was detected after p31 irradiation, but it cannot be presumed that we have made the phosphorus ions active as donors in diamond. The natural diamonds have a high and uncontrolled concentration of impurities and, when coupled with the radiation damage and graphitization problems, would appear to seriously limit the quality of semiconductor that we can presently achieve by ion implantation in diamond. ALTHOUGH diamonds are usually thought of as insulating in terms of their electrical conductivity, it was found about 15 years ago that natural semiconducting diamonds do occur rarely, and these were designated as type IIb diamonds. These p-type semiconducting diamonds were found to be dominated by an impurity level 0.37 ev from the valence band. Evidence today based on correlation of the concentration of acceptor states from Hall effect measurements with the impurity concentrations determined by neutron activation analysis point to aluminum as the dominant acceptor impurity.' The compensating donor is believed to be nitrogen, which has a donor level 1.6 ev above the valence band.' However, only a small fraction of the total nitrogen content in the diamond is electrically active. An infrared absorption band at 7.8 p and ultraviolet absorption near 4 ev have been associated with nitrogen, the former providing a quantitative measure of nitrogen content.3 The nitrogen content is -l020 cm-3 in insulating or type I diamonds, but is less than 10'' in natural semiconducting diamonds. Much of this nitrogen is distributed in platelets oriented in (100) planes and not atomically dispersed in the diamond lattice.4 Semiconducting diamonds have been deliberately formed by incorporating impurities into the graphite charge in the high-pressure apparatus used to form diamonds.5 These manufactured semiconducting diamonds are always p-type, and while some show the 0.37 ev level due to aluminum, most such samples have been ascribed to impurity banding effects.6 The best natural or manufactured semiconducting diamonds have hole mobilities near 1500 sq cm per (v-sec) at room temperature, and those with the 0.37-ev level can be analyzed to reveal an acceptor concentration of 3 to 8 X 1016 cm-3 and a donor concentration 3 to 10 times lower.' NO bulk n-type diamonds have ever been reported, but the electron mobility has been measured as 1900 sq cm per (v-sec) by irradiating a diamond with ultraviolet to excite electrons out of the deep nitrogen donor level or other levels.7 New hope for the formation of n-type diamond has emerged from the ion-implantation method whereby desired impurities are introduced into a crystal lattice by bombardment with a high-energy beam of the impurity ion. It was found in the case of silicon that the usual donors such as phosphorus and arsenic and acceptors such as boron and gallium could be implanted into silicon. Wentorf and arrow' produced semiconducting layers on diamonds by an ionic bombardment in a glow discharge at potentials of about 2 kv. The observed typeness from thermoelectric probing seemed to depend on the atmosphere gas (nitrogen, argon, or hydrogen) rather than on the electrode material, but the nature of the conduction process in the thin damaged surface layer is completely unknown. A Russian group under Vavilov has attempted high-energy ion implantation in natural diamonds using boron and lithium ions9 and later also phosphorus, aluminum, and carbon ions.10 Their papers claim n-type layers from lithium, phosphorus, and carbon implant and a p-type layer from boron and aluminum implant, though the methods of type determination are not described in detail. Under government contract support, the Ion Physics Corp. has studied ion implantation in several semiconductors. While the bulk of their study1' was devoted to the irradiation of silicon, they did carry out a short study on boron and phosphorus implantation into natural diamonds. They did observe surface conducting layers but did not determine the typeness of the layers. For our experiments, phosphorus and boron were chosen as the dopant ions because of their respective donor and acceptor behavior in germanium and silicon. Moreover, they are the lightest mass dopants of the shallow level donors and acceptors from columns 111 and V of the Periodic Table (excluding nitrogen which is already present in diamond), and will have the largest depth penetration into the diamond lattice. EXPERIMENTAL Diamonds. As the target diamonds for our ion implantation study, we chose commercially available macles, which are flat, twinned diamond crystals. By scanning through the stock of a wholesale distributor

Jan 1, 1970

By E. F. Koch, J. L. Walter

oriented crystals of iron and iron with 3, 5, and 6.25 pct Si were rolled to reductions of 10 and 70 to 97 pct at room temperature. Similarly oriented crystals were deformed in tension. Dislocation substructures of the deformed crystals were observed by transmission electron microscopy to determine the effect of silicon on the formation of substructures. Pole figures were obtained to relate orientation changes to substructure. When rolled 10 pct, the iron crystals and the 3 pct Si-Fe crystals formed cells, 1 and 0.2 u in diameter, respecliuely. Cells were absent in the higher-silicon crystals. Extended dislocations and possible stacking faults were observed in the 6.25 pct Si-Fe crystal rolled 10 pct and annealed at 650°C. The stacking-fault energy was estimated to be 20 ergs per sq cm. Rolling to 70 pct resulted in the formation of sub-bands (0.9 µ wide) ill the iron crystals and transition bands (containing 0.2-µ-wide subbands) in the 3 pct Si crystals. No subbands formed in the 5 pct Si-Fe crystal until it was ankzealed. SliP occurred on (112) planes ill tension. The slip traces on the 3 pct Si crystal were wary while those on the 5 pct Si crystal wvere straight. The strain-hardening coefficient for the 5 pct Si crystal was nearly zero. Cells did not form, at least at elongations up to 10 pet. The results suggest that cross slip of iron is restricted by additions of silicon beyond about 3 pct possibly by formation of immobile extended dislocations. IN a previous paper' the authors described the substructures developed in (100)[001]-oriented crystals of 3 pct Si-Fe which were rolled to reductions of 10 to 90 pct at room temperature. At low reductions (10 to 20 pct) cells, approximately 0.2 to 0.3 ja in diameter, were formed. The cell walls consisted mainly of edge dislocations. With increasing reduction (up to 50 pct) the cells were seen to elongate in the rolling direction. In certain regions of the crystal there were significant reorientations which were characterized as rotations about an axis normal to the (100) or rolling plane. These regions were called "transition bands". The regions in which there were no reorientations were called ('deformation bands". At reductions of 60 to 70 pct the elongated cells in the transition bands became sub-bands separated by low-angle tilt boundaries with angles of disorientation of about 2 deg. The elongated cell structure in the deformation band was replaced by a general distribution of dislocations. It was noted that the width of the subbands in the transition bands remained 0.2 to 0.3 µ; i .e., the width of the subbands was the same as the initial cell diameter for reductions up to at least 70 pct. From this, and from considerations of the mechanism of formation of the transition bands,' it was concluded that the subbands evolved directly from the initial cells. In order to check this conclusion, it was decided to examine the relationship between initial cell diameter and width of subbands produced by large rolling reductions. Cell size is known to be dependent upon the temperature of deformation.2,3 However, preliminary experiments with 3 pct Si-Fe crystals indicated that the change in cell size with increasing temperature of deform,ation was not sufficient for the present purpose. On the other hand, cell diameters generally reported for iron deformed at room temperature2'3 range from 1 to 2 p, a factor of 3 to 10 larger than the cells in 3 pct Si-Fe rolled to 10 pct reduction,' indicating the possibility of a marked dependence of substructure (at least in terms of cell size) on the amount of silicon in iron. Thus, the investigation was enlarged to include the study of the effects of varying silicon content on substructure in lightly rolled as well as in heavily rolled crystals of iron and iron with 3, 5, and 6.25 pct Si. The crystals used in this study all had the same orientation, (100)[001], with respect to rolling plane and rolling direction. These were rolled to reductions of from 10 to 97 pct and the substructures determined by electron transmission microscopy in both the rolled state and after annealing. In addition, stress-strain curves were obtained from (100)[001]-oriented crystals of iron and 3 and 5 pct Si-Fe to determine the effect of silicon on tensile properties. The dislocation substructure of the tensile specimens was also determined for Samples pulled to 2 and 10 pct elongation at room temperature for comparison with the substructures produced by rolling. 1) EXPERIMENTAL PROCEDURE Crystals with 3, 5, and 6.25 pct Si were prepared by annealing 0.012-in.-thick sheets of high-purity Si-Fe in purified argon at 1200°C to effect growth

Jan 1, 1965

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

By Simon D. Strauss

What are future prospects for U.S. mining? In many quarters the assumption is made that this country has passed its zenith as a mineral producer -- that it is in a period of decline and that it is becoming a have-not nation like Japan and much of Western Europe. These industrial rivals of ours must depend almost entirely on others for their mineral supplies. In trying to answer this question one must of course distinguish between resources and productive capacity. In today's volatile and competitive markets, the definition of what are reserves and what are merely identified resources becomes ever more difficult. Many large deposits have been found that are unlikely to be viable in the marketplace under normal conditions but that can be of significance to the nation's military and industrial security in times of emergency. I should like to draw on personal experience from World War I1 for illustration. 4fter Pearl Harbor great concern developed over the availability of a long 1ist of strategic materials for which this country was largely dependent on imports. Included were a number of minerals of which domestic deposits had been identified. Among these were chromite, manganese ore, mercury, mica and tungsten.

Jan 1, 1982

P. H. ARGALL, Magdalena, N. Mex. (written discussion *).-The Chilean mill has generally been considered a fine-crushing machine and as such has had many advocates; it has also. had quite a number of denouncers; hence, the action of the Portland engineers in using the Chilean mill for the preparatory work usually accomplished in, rolls or rock breakers and adding a ball mill to do the fine grinding is novel, though of doubtful utility in the long run, even though a fair efficiency is obtained for the combination machines, as measured by Chilean mill practice. In order to follow the development of Chilean mill practice on Cripple Creek ores, I might say that two 6-ft., Chilean mills were placed in operation in Stratton's Independence mill in April, 1908, treating ore crushed by rolls to pass Y4 in. screen aperture. Screening was, however, found to be an unnecessary refinement, as was also the use of plows in the mills; both screening and plowing were abandoned before the Portland engineers finished the experiments in stamp milling upon which they were then engaged. Two additional 6-ft. Chilean mills were added in the spring of 1911, three of them giving the required 10,000 tons per month capacity, one being always in reserve. The Portland company began using Chilean mills in June, 1910, at its Victor mill, and the same company purchased the Stratton's Independence mill in June, 1915, and remodeled it; it is now known as the Independence mill. A description of Stratton's Independence milling practice, is given in the November, 191.1, issue of Mining Majazine (London). These Chilean mills were used as fine grinders and that they accomplished their purpose is shown by the screen analyses, in which 62 per cent. of the pulp passed 150-mesh screens. To make coarse crushers of these Chilean mills, the Portland engineers have increased the speed, substituted steel in various parts for cast iron, provided new and enlarged thrust bearings to take care of the centrifugal force incident to higher speed, and have, thereby, greatly increased the cost of the machines. They have also reduced the width of the tires and dies from 8 in., as used in the original mill, to 7 in., a reduction of 12 ½ per cent. in the crushing surfaces, to say nothing of the loss of abrasion or attrition incident to the larger surface. At the same time, they have apparently increased the weight of the rollers by using tires 5 7/8 in. thick as against tires varying between 3 and 4 in. on the original mills, thereby increasing

Jan 4, 1920

ALBERT J. PHILLIPS, Chairman E. H. Dix, JR., Past-chairman R. H. LEACH, Vice-chairman R. F. MEHL, Vice-chairman W. M. COME, Treasurer LOUIS JORDAN, Secretary 29 West 39th St., New York, N. Y.

Jan 1, 1937

By Frederick Laist

About six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electronegative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection—1 mg. or less per liter. A pure zinc is soluble only with difficulty in sulfuric acid; an impure zinc dissolves very readily. Electrolytic zinc deposited from pure solutions is, of course, extremely pure and dissolves only about one-fiftieth

Jan 1, 1921

By H. E. Cline

Mechanical properties of the eutectic between CoAl and cobalt were measured over a range of- temnperatures and strain rates for a variety of microstructures produced by directional solidification and by thermo-mechanical processing. Directional solidification led to rodlike, lamellar, and irregular microstructures. The unusually high volume fraction of the cobalt-rich rods and the lurge spacing of the rods were explained by the phase diagram. The hot-worked structure consisted of fibers of COAL in a cobalt-rich matrix. The roonl- tevlperature strength of the uvrought material increased with decreasing grain size but the 1000°C strength decreased with decreasing pain size. At high temperatures the directionally solidified tnaterial was stronger and less strain-rate-sensitice than the hot-rolled material. The fine-grained hot-worked ma-terial became superplastic at high temperatures, with tensile elongations greater than 850 pct, while at root temperature this material was ductile and impact-resistant because of the ductile matrix. Fracture occurred in the directionally solidified material at elevated temperatures by inter phase separation and at roorn temperature by cracks in the intermetallic phase. Growth of these cracks was impeded by the ductile cobalt-rich phase. It was found that the CoAl intermetallic remains ordered at elevated temperatures. DIRECTIONAL solidification of eutectic alloys has been used to produce structures consisting of parallel rods or lamellae. Although the spacing of the phases depends on the growth rate, it has been observed to be of the order of 1 µ in many eutectics. A strong intermetallic phase has been used to reinforce a ductile matrix in the rod eutectic A1-Al3Ni and the lamellar eutectic Al-Al2cu.1 The microstructure of the eutectics A1-A13Ni and A1-A12Cu remained aligned after samples of these alloys were exposed to temperatures just below their melting points for long times. Stability of the microstructure at elevated temperatures makes directionally solidified eutectics a candidate for high-temperature applications. Recently Thompson4 has developed the Ni-NiMo eutectic containing 40 pct NiMo lamellae, giving a tensile strength superior to nickel-base superalloys. Unfortunately, this eutectic oxidizes rapidly at elevated temperatures. By mechanically processing a two-phase structure, one may reach strengths as high as 700,000 psi, as demonstrated by drawn pearlite.5 In this case the strengthening mechanism was thought to be related to the fine substructure formed during deformation.5 However, a heavily worked structure may recrystallize and coarsen at elevated temperatures. Some worked eutectics such as Al-Al2Cu,6 Pb-Sn,7 and Sn-Bi7 have shown unusually large elongations in tension when tested at elevated temperatures. This phenomenon of large extension, called "superplasticity", was related to the fine grain size of wrought two-phase alloys at elevated temperatures. A mode of deformation of "superplastic" material has been shown to be grain boundary sliding,' which has also been observed during creep of polycrystalline materials.9 The Co-A1 system was chosen for this investigation after examining the phase diagrams of binary eutectics." The high melting point of 1400°C, the aluminum content which was expected to give oxidation resistance, and the properties of the intermetallic CoAl were the chief factors influencing this choice. This eutectic consists of a mixture of the intermetallic CoAl and a cobalt-rich solid solution. The intermetallic CoAl has a large range of solubility and a CsCl structure." From the similarity between CoAl and NiAl one would expect CoAl to be ordered at elevated temperatures; however, specific heat measurements" show a transition at 800°C. West-brookL2 has measured the hot hardness of CoAl and found a rapid decrease in hardness above 600°C. The tensile properties and stress rupture properties of as-cast CoAl-Co eutectic were measured by Ashbrook and wallace13 who report a room-temperature tensile elongation of less than 1 pct. I) EXPERIMENTAL A) Sample Preparation. Experimental materials were prepared by directional solidification, by hot working, and by powder processing. The starting materials were electrolytic 99.9 pct pure cobalt and 99.99 pct pure aluminum. 1) Directional Solidification. A vertical Bridgman apparatus heated by induction was used to directionally solidify cylindrical ingots $ in. in diam and 5 in. long. The apparatus was first evacuated and then an argon atmosphere was introduced to retard evaporation. The ingots were contained in an alumina crucible inside a graphite susceptor that rested on a movable water-cooled base. The base was lowered out of the induction coil at a constant rate. Eight of the ingots were solidified using a drive rate of 2.5 cm per hr, two of the ingots at 1.2 cm per hr, and one ingot at 10 cm per hr. The eutectic composition Co 10 wt pct A1 was used in all but one ingot which had the composition of the stoichiometric CoAl intermetallic, Co 32 wt pct Al. 2) Mechanical Processing. At 1000°C the eutectic Co 10 wt pct A1 is a mixture of an intermetallic phase, Co 21 wt pct Al, and a cobalt-rich phase, Co 5 wt pct Al.10 These phases differ from the stoichiometric CO 32 wt pct A1 and pure cobalt because of the large solubility of this eutectic at elevated temperatures." Four rectangular slab ingots, 4 by 1 by 12 in. high, of Co 10 wt pct Al, Co 5 wt pct Al, Co 21 wt pct Al, and Co 32 wt pct A1 were cast for hot rolling. The cobalt was first vacuum-melted, H2-treated for 20 min,

Jan 1, 1968

By E. Heaton Hemingway

DURING the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000° C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source impossible. In other words, the only volatile products that could be obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the earlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weights of the turnings before and after being heated were widely inconsistent, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube either in the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 8, 1920

By A. B. Parsons

DOWN in Washington an army of individuals constituting the government of a so-called "'democratic" nation is trying to manage the conduct, in its rnultifold phases, of the greatest war in history for the country that is potentially, at least, the strongest in the world and on which, consequently, the major responsibility rests. The enterprise is one of unprecedented magnitude and complexity. That individuals and groups have made and are making serious blunders, both as to the establishment and execution of policy, is to be expected.

Jan 1, 1942

[Separates of all the Pamphlets published within the last three years (starting with No. 1469) are available, with few exceptions, at Institute headquarters. Separates of all the Technical Publications are also available. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.] METAL MINING TRANS. PAMPHLET VOLUME NUMBER TITLE AUTHOR MEETING AND PAGE* -1033 Relation of Air Pressure to Drilling H. W. Seamon New York 66,743, 766 Speeds of Hammer Drills Feb., 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York - 66,711 Feb., 1921 1 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples- Feb., 1921 1038 Discussion of Papers Presented in 1920 1041 Run-off and Mine Drainage - H. N. Eavenson New York 66, 624, 630 Feb., 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb., 1921 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 282 Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1921 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66,758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-steel Tests F. B. Foley New York - 66,789 Feb., 1921 1077-M Application of Magnetic Analysis to C_ W. Burrows New York 66,796 Root Drills Feb., 1921 1078-M Heat Treatment of Rock-drill Steel G. H. Gilman New York 66,779 Feb., 1921 1080 What is the Ideal Drill Steel? F. H. Kingdon New York 66,807 Feb., 1921 1081 Rock Drill Steels, etc. W. T. Ober New York 66,814 Feb., 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66, 715, 721 Definition and Valuation Sept., 1921 1084 Drill Steel from Hollow Ingots P. A. E. Armstrong New York 66,809 Feb., 1921 1088 Authors' Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A. E. Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft of Davis- J. L. Bruce Wilkes-Barre 66, 252, 268 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66, 580, 605 ment for a Mine Hoist Sept., 1921

Jan 1, 1926

By Larry Dale

An approach for predicting the development of mineral resources on public lands has been developed as an aid to resource agencies. It consists of new techniques for evaluating the economic potential of the resource, the uncertainty about mine cost estimates, and the uncertainty about the occurrance of mineral deposits. New mineral sup- plies from inferred and hypothetical resources can be predicted by using these techniques. A case study illustrates their application in predicting development of copper resources in western Montana.

Jan 1, 1982

Executive ARTHUR S DWIGHT, Chairman B THAYER CHARLES F RAND P MATHEWSON J V W REYNDERS Membership WILLIAM H BASSETT, Chairman W Y WESTERVELT Vice-chairman P MATHEWSON H G MOULTON F T RUBIDGE Finance WALTER H ALDRIDGE, Chairman GEORGE D BARRON GALEN H CLEVENGER

Jan 1, 1923

By F. H. Deily, D. S. Rowley, R. J. Howe