Search Documents

By S. T. Wlodek, John Wulff

Dense, adherent, and ductile coatings of chromium can be applied to Molybdenum by selectively freezing out the chromium solute from a supersaturated copper-or tin-rich liquid alloy. The successful exploitation of this technique depends on the control of variables common to any freezing process. Under the most favorable combimtion of supersaturation, nucleation, and mass-transfey, coatings as thick as 0.004 in. can be obtained. In exploratory experiments it was found that a coating of chromium may be applied to molybdenum by immersing the molybdenum body in a supercooled copper-chromium or tin-chromium melt and selectively freezing out the contained chromium onto the molybdenum body. Supercooling of the liquid metal plating bath can be achieved by cooling, or the maintenance of thermal or concentration gradients in the melt. The technique is similar to conventional dip-plating procedures where the sample is immersed in a molten bath of the pure plating medium, except that in these studies, the plating medium consisted of a dilute solution of chromium in liquid tin or copper. The success of this method requires that the base material to be plated be isomorphous with the coating and insoluble in the plating bath. In addition, the plating bath, while having an appreciable solubility for the coating component, must have negligible solid solubility in the solid plate. Such relationships exist in the molybdenum-chromium, chromium-tin, and chromium-copper systems. Liquid tin and copper are satisfactory as the plating solvent, because although chromium is appreciably soluble in both of these liquid metals, solid inter-solubility is almost negligible, and no compound formation occurs. The same relationships exist between molybdenum and copper or tin except that the solubility of molybdenum in liquid tin or copper is insignificant. It is this combination of solubility relationships, as well as the completely isomorphous nature of the molybdenum-chromium system, which allows the formation of a chromium coating on molybdenum by the selective freezing mechanism. Since the main deterrent to the widespread use of molybdenum for high-temperature structural applications is its poor oxidation resistance, the formation of a dense and ductile chromium coating on molybdenum may well be of commercial significance. In addition, the basic principle of coating formation by selective freezing should be applicable to other metallic or even nonmetallic systems. The precipitation of the solute from a liquid metallic solution, for the formation of a protective coating, has not been previously considered in the literature. Frequently, however, a similar phenomenon has been described in the corrosion of metallic heat exchangers by liquid metals1 wherein temperature gradients in the liquid metal heat-transfer medium result in the formation of layers or deposits of metallic residue2 in the cooler portions of the system. Impregnating techniques using liquid baths have been tried as a plating process. Semchyshen and Barr, for instance, have successfully diffused chromium into molybdenum by immersing the molybdenum specimen in a liquid tin-chromium or copper-chromium alloy. This simple holding technique fails to produce a layer of pure chromium and requires prolonged immersion to allow for the diffusion-activated enrichment of the molybdenum. During the course of this investigation, most of the phase relations published for the copper-chromium4 and molybdenum-chromium4 systems, were found reliable. It was necessary, however, to investigate the solubilities of chromium and molybdenum in liquid tin as well as the solubility of molybdenum in liquid copper. These determinations were made by a simpie weight loss technique on materials of the same purity as used in the plating studies. The results of these solubility studies are given in Tables I and I1 and indicate that although the solubility of molybdenum in liquid

Jan 1, 1961

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950

By J. W. Leomrd, B. A. Donahue

Results of research are presented examining the extent to which the analytical characteristics of the relatively distinct coal bands from a variety of coal seams can be related to each other. This paper dis-cusses an approach for developing a practical coal petrographic quality control program based on conventional analyses, most of which is part of the standard A.S.T.M. procedure. The work is a final follow-up to Part I of this series which was prepared by the authors as an approach to applying conventional coal petrography to single coal seams. Recent published work by the authors entitled Petrography for Coal Mining and Coal Prepration: Part I dealt with interrelating various chemical and physical properties of coal1 measured using conventional analyses made on distinct petrographic bands taken from single coal seams. Since most coal production facilities process coal from a single coal seam or from very closely related coal seams in the same area,2 emphasis on interrelating the properties within a single seam appeared appropriate. The distinct petrographic bands were analyzed on the assumption that such differentiated data would be more representative of a heterogeneous coal seam than the single analytical value commonly used to characterize each property of an entire seam.34 Effort was directed at demonstrating the extent to which the interrelated chemical and physical properties 5,6 could be developed into nomographs or petrographic standardization graphs. Thus, one analysis, determined on a series of petrographic fractions separated from a single sample, was used to estimate numerous other properties in each fraction by referring to the previously established petrographic standardization graphs. This conventional approach to coal petrography was undertaken as a suggested feasible means by which a few coal analyses could be employed to develope a more penetrating knowledge of the properties of coal from any given seam in order to monitor more extensively its performance at the point of utilization. Such procedures can support development of the type of in- formation commonly sought through automated testing and through the use of computers.7 The broad knowledge which can be developed through these procedures is intended for application in the generation of an analytical profile or broad characterization of coal. These estimates were not intended as replacements for individual coal analytical tests. In this expanded second part of the research program, distinct petrographic bands from nine coal seams in the Central Appalachian Region were physically and chemically analyzed to elucidate the extent to which this concept of conventional petrography could be broadened for application to numerous coal seams. In presenting this second phase of work, the relationships developed are presented individually and not in a connecting series of nomographs or petrographic standardization graphs as in the previous work, thus leaving open the combinations of possibilities to individual interpretation and application. MATERIAL AND EXPERIMENTAL WORK Nine coal seams, representing a wide range of rank, from the Central Appalachian coal fields were used in this study. The distinct petrographic bands from the Kittanning, Pond Creek, Jawbone, Tiller, Poca-hontas No. 3, No. 2 Gas, Eagle, Winifrede, and Pittsburgh coal seams were separated by carefully removing a portion of each band at the face of the seam. The following were determined: ash, sulfur, free swelling index, heating value, bulk specific gravity, volatile matter, Hardgrove Grindability Index, and Gieseler Plastometer measurements. Determinations, where procedures were available, were carried out using ASTM standard procedures.8 Bulk specific gravity was determined using a kerosene volume displacement procedure modified from a method applied by Headlee and McClelland of the West Virginia Geological survey,9 Those bands with a bulk specific gravity greater than 1.60, which is generally above the practical specific gravity cleaning range of bituminous coals, were excluded and no analyses were performed. Much of the initial organization of this second phase of work was developed through the extensive use of a computerized statistical monitoring program (see Ref. 4). However, in order to achieve the closest possible interpretation of results, the final organization of data proceeded mainly from exhaustive trial

Jan 1, 1968

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation&apos; indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in&apos; all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest &apos;Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen&apos;s _ % CaO&apos;. 100/% CaO + % SiO2 where (%CaO&apos;) = % CaO- 1.18% P2O5. Herty&apos;s B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By William A. West

One manifestation of anelastic properties in solids is the mechanical elastic aftereffect, which may be described briefly as follows: If a stress is applied to a solid body, a deformation or strain is produced. On removal of the stress, this deformation disappears, at least in part. As a first approximation, this appearance or disappearance of deformation usually has been considered instantaneous. Actually, however, for a very wide variety of substances, on application of stress the instantaneous deformation is followed by a further slow yielding, which continues, although at a rapidly diminishing rate, for as long as the stress is applied. Similarly, on removal of the stress, the instantaneous recovery from deformation is followed by a further slow recovery, which continues, although at a rapidly diminishing rate, often for a long time. This latter phenomenon has been called the "elastic after-effect." Experiments upon the elastic after-effect in metals, when properly designed and when properly interpreted, are capable of giving quite precise information regarding the relation between stress and strain in the various constituent parts of the metal. For example, if certain parts of the metal, such as grain boundaries or slip bands, behave in a viscous manner—that is, if therein—the relaxation spectrum will contain lines or bands associated with the relaxation of shear stress within these parts. No attempts have heretofore been made to utilize elastic after-effects for obtaining such detailed information. The purpose of the present paper is to explore the possibilities of properly designed and interpreted experiments on the elastic aftereffect in metals. Since new procedures and principles are employed in this study, an attempt has been made to record each step taken. Elastic after-effect observations are susceptible of simple interpretation only when the stress level employed is so low that all effects are linear with the stress. Just how low the stress level must be can he determined only by experiment. An advnntage, other than simple interpretation, is associated with low stress levels. When all effects are linear, derived quantities, such as the relaxation spectrum, are independent of the stress distribution. It is, furthermore, possible to employ the type of deformation that is most convenient from the experimental standpoint; for example torsion. It appears that in experiments involving both loading and unloading the following would be observed: I. Instantaneous deformation, recoverable instantaneously in whole, or in part. 2. Delayed deformation, recoverable slowly in whole, in part, or not at all. 3. Permanent deformation, the difference between total deformation and total recovery. In the work here described, unloading experiments only were made. Wires were

Jan 1, 1947

By C. P. Besse, N. F. LeBlanc

Described in this paper are oceanographic data which should be considered by an offshore design engineer and methods for developing a design wave height from the oceanographic data. The selection of a design wave is predicated on contemplated waves which might affect the site throughout the life of the structure. Selection of a design wave height may be based on (1) arbitrarily established recurrence Frequencies of hurricanes affecting the structure (predicted wave heights are associated with the expected variations of forces resulting from these waves) and (2) a risk-type evaluation wherein all possible storms affecting the area are considered (anticipated wave heights are associated with both investment plus risk costs and expected variations of forces). It is shown how the following oceanographic predictions are integrated into design considerations: (1) a classification of storm intensity which considers all recorded storms which affected the design area, (2) the recurrence interval of storms of a given- intensity (this interval is dependent on the extent of the geographical area considered in the design problem) and (3) a forecast of all wave heights which might affect the area (geometry of a structure often necessitates consideration of waves from a multiplicity of directions). The authors believe that the described techniques can result in selecting an adequate and reasonable design wave. INTRODUCTION Since the inception of offshore operations in the Gulf of Mexico, engineers engaged in designing suuctural facilities have been plagued with the problem of selecting an adequate and reasonable design wave. In the development of any offshore structure it is mandatory that the engineer evaluate the ability of the structure to withstand the ocean waves to which it will be subjected. Selecting such design waves quite naturally necessitates a coalition of the oceanographer and the design engineer. The oceanographer must provide a detailed knowledge of scientific principles which govern the behavior of waters in the Gulf of Mexico. He should also have an adequate knowledge of the manner in which design waves are utilized by the engineer. Although the design engineer&apos;s primary responsibility is applying the oceanographer&apos;s specialized knowledge in the creation of real structures, it is important that he possess some knowledge of related oceanographic principles to reasonably evaluate and apply the recommendations of the oceanographer. In the Gulf of Mexico it is the hurricane wind waves which generally govern the design of an offshore facility. The oceanographer must therefore develop techniques for predicting the heights, periods and frequency of all hurricane waves which might affect a particular structure. From this mass of oceanographic data, the design engineer must select the design waves which will apply to his particular design. PAST STUDIES ON FREQUENCY AND AMPLITUDE OF HURRICANE WIND WAVES Past oceanographic studies on the frequency of hurricane wave heights in the Gulf of Mexico have been devoted largely to predicting the recurrence interval of hurricanes which will generate maximum significant waves of given heights. The maximum significant wave height is the average height of the highest one third of the waves in that portion of the storm producing maximum wave heights. Since these waves occur over a relatively small portion of the storm (Fig. 1) and since the paths of hurricanes vary considerably (Fig. 2), the recurrence frequency of such heights is largely a function of the extent of the geographical area considered. In establishing the frequency of maximum significant waves for the entire American Gulf coast, the major fully developed hurricanes which affected the coastline from BrOwnsville, Tex., to Key West, Fla., were considered (Fig. 2). These Storms were selected and described by C. L-

By S. Shapiro, G. Krauss

RECENT investigations1 3 of the products of marten-sitic transformation in Fe-Ni and Fe-Ni-C alloys have made use of light microscopy to describe mar-tensitic fine structure. The application of conventional metallographic techniques to this problem was possible because of the similarity of distributions of parallel striations developed by etching polished surfaces to distributions of transformation twins which are positively identified in thin films by transmission electron microscopy. The surface striations frequently are not well-defined, and could also be due to, for example, rows of etch pits which are not resolved by the light microscope. This note describes the etching effects revealed by examination of surface replicas of mar-tensite in the electron microscope. The application of a replica technique both extends the observations of fine structure made with the light microscope and allows the results of conventional metallography to be used with more confidence. Samples of an Fe-33 wt pct Ni alloy were used for this study because of the detailed knowledge of the fine structure of martensite which has been developed&apos;-4 for alloys of about this composition. Samples transformed to martensite at -120°C, and transformed samples heated to 340°C to effect a small amount of reversal of martensite to austenite, were examined. Surfaces were first prepared for replication by elec-tropolishing in a chromium oxide-acetic acid electrolyte at a current density of 0.1 amp per sq cm and a temperature of 15°C or a perchloric acid-acetic acid electrolyte at a current density of approximately 2 amps per sq cm and a temperature of 15°C. The polished surfaces were then etched for 4 to 7 sec by immersion in a solution of equal parts HC1, HNO,, and H20. Application of the etchant for this period of time produced discrete attack of certain features without loss of resolution due to overlapping of areas most susceptible to etching. The etched surfaces were replicated by 1) preshadowing with Pt-Pd alloy at an angle of 20 to 30 deg, 2) depositing a thin carbon film, and 3) stripping the film and shadowing material by immersion in a 5 pct nital solution. Two types of etching effects were observed by examination of the surface replicas in the electron microscope: l) continuous striations centered at the bottom of long grooves or the tops of pyramidal elevations on the sample surface, and 2) high densities of fine etch pits. Examples of both types of features are shown in Figs. 1 to 4. The striations are in each case continuous and have the same characteristic configurations as do transformation twins in martensite. Fig. 1 shows that the density of grooves decreases toward the edge of a martensite plate and Fig. 2 shows a region where the striations are of varying length. Similar examples of transformation twin arrangements determined by transmission electron microscopy of thinned foils of martensite have been shown in the literature,&apos;~ and, based on these similarities, the striations and their associated grooves or mounds are considered to be evidence for the presence of transformation twins. The transf~rmation twins in martensite are on the order of l00 A thick, much too fine for resolution by the light microscope. It appears that orientation-dependent etching of the matrix martensite about the twins results in grooves or surface elevations which

Jan 1, 1967

By E. I. Salkovitz, F. W. von Batchelder

DURING the last few years several papers1-&apos; have been published in which internal friction measurements have been used to determine the quantity of carbon or nitrogen dissolved in a iron. This method is based on the fact that, in pure Fe-N and Fe-C alloys, nitrogen and carbon cause peaks in the internal friction vs. temperature curve; at a frequency of 1 cycle per sec (cps) these peaks appear at $-200 and +360C, respectively, and if internal friction is expressed as Q-1, which is equal to times the logarithmic decrement, this figure will, by coincidence, give the weight percentage of nitrogen or carbon in solid solution.&apos; In most of the studies published, very pure iron (Puron) was used. In one case the influence of manganese on the behavior of nitrogen in a iron was mentioned.4 It would be of great value, especially for the study of aging and related phenomena, if this method could be applied to commercial mild steel with norrnal percentages of manganese, phosphorus, sulphur, etc. As a rule, in such steels carbon and nitrogen are present together, and the amounts of these elements in solid solution should preferably be determined separately. The fact that their internal friction peaks appear at different temperatures (+36° and + 20°C in pure iron) seems promising for such a selective determination. It is necessary, however, that the peaks are narrow enough not to interfere with one another, and further, that there is no effect from carbon on the behavior of nitrogen in stress induced diffusion, and vice versa. According to Fast,&apos; however, in the presence of manganese the nitrogen peak gets wider and appears at a higher temperature nearer the carbon peak, and thus the prospects for selective determination are reduced. (The carbon peak was not affected by the presence of manganese.) But even if fully quantitative de- terminations of the two elements are not attained, some relative figures on the sum of them and an indication of which one is the predominant one, would be of value. Some results from experiments along these lines will be reported here. An internal friction measuring device was assembled mainly following a description by KG." The measurements were also carried out as reported in that paper. Table I gives the chemical compositions of the four different materials used in this investigation. All materials were drawn to wires with diameter about 0.8 mm, and the analyses refer to these final shapes. Determination of Nitrogen Peak Wires from steels A, B, and C were decarburized in wet hydrogen (about 30 pct H2O) at 700°C until no carbon or nitrogen could be found by chemical analysis. No peak was then found in the internal friction. The wires were further annealed at 580°C for 16 hr in hydrogen bubbled through a solution of 6.8 pct NH3 in distilled water. Chemical analyses gave 0.04 pct N in A and C, and 0.06 pct in B. After annealing at 580°C for 15 min in a lead bath and water quenching, the internal friction was immediately measured. The resulting curves are shown in Fig. 1. At these high values of the internal friction the accuracy is comparatively poor; at Q-1 - 0.030 it is estimated to be 0.002. In order to make possible a calculation of the activation energy for diffusion of nitrogen, measurements were made at two different frequencies. Steel A shows rather broad peaks, and their temperatures can hardly be expected to be very accurate. Steels B and especially C are better in this respect. The finding of Fast&apos; that manganese broadens the nitrogen peak is con-

Jan 1, 1953

By F. F. Poland

The purpose of this paper is to describe the recent applications and improvements made in the process and equipment for the recovery of metallic zinc from secondary metals by means of high temperature electric resistor furnace distillation. The process and high temperature furnace, as developed by Revere Copper and Brass Incorporated, Research and Development Department, was described in a previous paper. † Since the publication of that paper the process and equipment have been licensed to others. Consequently its field of application has been expanded, particularly for the treatment of scrap brass, galvanizers dross and scrap zinc. Other applications are being considered, particularly the melting of metallic titanium and special alloys requiring a controlled atmosphere. Consideration is also being given to modification in design that would allow the melting of copper cathodes for the production of oxygen-free and electrolytic tough pitch copper shapes without the necessity of blowing and poling. In the design of a furnace for melting copper cathodes it is intended that the fundamental principle of charging the solid material into a large pool of molten metal through a double door charging vestibule as shown in Fig 3 of the previous paper, † would be adhered to and, in addition, either dehydrated and desulphurized producer gas or commercial nitrogen, that is, approximately 96 pct nitrogen, 2 pct hydrogen 2 pct CO, also dehydrated, would be used to provide a protective atmosphere for the resistors and to flush out more soluble gases from the molten copper. The operation of a small unit producing approximately 1000 lb of copper per hr has shown that the commercial nitrogen will allow the production of tough pitch electrolytic copper when the metal is transferred from the meltdown unit contemplated to a special type induction unit where the oxygen absorption and temperature can be controlled. Standard practice in treating low grade scrap brass has been to oxidize the zinc by blowing air through the molten metal. This operation results in the recovery of approximately two-thirds or less of the zinc content of the brass in the form of an impure zinc oxide having only a fraction of the value of the zinc in metallic form. The balance of the zinc is lost to slag, fume and drosses. Fig 1 shows the revised flow sheet of the process for the treatment of scrap brass. For this application and as shown on the flow sheet a low frequency induction furnace has been substituted for the Wilkins-Poland type as a melting unit. This type of furnace has been found the most suitable for the purpose as will be shown by the following discussion. Serap Brass The melting of refinery scrap brass preparatory to distillation presents a melting problem quite different from the usual melting of brass mill scrap for recasting because refinery scrap is a heterogeneous mixture of alloys each having different melting and boiling points, and coated with a variety of corrosion products and foreign materials. In addition, brass and copper plated pieces of sheet iron, stainless steel, ceramic materials, and others are present that do not melt except at temperatures above the boiling point of the liquid bath. In the previous paper it is noted that difficulty was encountered in the melting of refinery grade scrap brass without excessive loss of zinc by volatilization and that 5 to 10 pct razorite flux was used to alleviate this condition. While this flux was successful in preventing the excessive loss of zinc by volatilization it interposed a low heat conductivity layer between the source of heat and liquid charge and resulted in lowering the melting rate of the furnace. This same problem presents itself in all types of furnaces in which the metal is heated by radiation and conduction from above the charge. It has been found in melting this type material that the melting rate per hour or per square foot of hearth area

Jan 1, 1950

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By C. J. Rosa, W. C. Hagel

An attempt is made to determine the diffusion coefficients of oxygen ions in hypostoichiometric zirconium oxide. A phenomenological theory is developed for three-phase, unidirectional volume diffusion of a gaseous species from a planar source. Knowledge about oxygen diffusion in a and ß zirconium and experimentally measured rates of movements of interfaces permit the evaluation of oxygen ion diffusivi-ties in ZrO2-x. The results conform to the relationship: sq cm per sec, for the temperature range of 875" to 1050° C. DIFFUSION coefficients of oxygen ions in stoichio-metric oxides have been studied by many investigators. The obtained results not only supplement the knowledge about the lattice-defect structures of oxides and conduction mechanisms but also provide information of technological importance. Rate processes such as oxide sintering, high-temperature creep deformation, and oxidation of metals and their alloys are directly dependent on diffusion phenomena. Unfortunately, diffusion coefficients obtained from studies on stoichio-metric oxides cannot be treated without restraints when applied to oxidation kinetics, if precise evaluations of oxidation rates are desired. Oxides formed on metals are usually nonstoichiometric and exhibit nonuniform distribution of either cation or anion vacancies across their thicknesses. Debuigne and Lehr1 extended Danckwerts&apos;2 mathematical analyses and furnished a semitheoretical treatment for evaluating oxygen diffusion coefficients in zirconium oxide in terms of weight gain measurements during oxidation of zirconium in the temperature range 400° to 850°C. Their calculations are based on theoretical partitioning3 of the total amount of oxygen between a zirconium and its oxide phase. An inherent discrepancy appears to continue throughout their calculations. The amount of oxygen confined to the oxide phase should be corrected by multiplying the calculated oxide thickness by the inverse of Pilling-Bedworth ratio, if expansion of zirconium dioxide is taken into account. The purpose of the present investigation is to provide a new semitheoretical treatment for evaluating diffusion coefficients of moving species in hypostoichiometric oxide. The analyses are relevant to unidirectional volume diffusion. Although the presented method is quite general, its applicability will be discussed in terms of kinetic measurements from oxidation of zirconium at temperatures above the a/ß transition, for reasons stated in the later part of this paper. EXPERIMENTAL Pure, 99.93 wt pct, zirconium samples of approximately 2 by 1 by 0.35 cm were exposed to oxygen for various times at four temperature levels: 875°, 950°, 1000°, and 1050°C. High-purity, better than 99.9 vol pct oxygen was passed through a cold trap and columns containing anhydrous CaSO4 to remove residual water vapor. Before exposing to oxygen at a pressure of 500 Torr, specimens were subjected to wet abrasion on 200- through 600-grit Sic papers and polished with 1—p diamond dust. Prior to oxidizing, all zirconium samples were vacuum-annealed at 10-6 mm Hg for about 15 min at the test temperature. The temperature variation across the uniform heat zone was ±2°C from the preset value. Final polishing, for phase thicknesses measurements, was performed by using 8- and 1-p diamond dust and followed by vibrator polishing with 0.05-µ ? Al2O3 solution. Measurements of phase thicknesses were made by projection on a metallographic viewing screen. Conventional powder X-ray analyses for the oxide were employed. RESULTS Fig. 1 is an example of the cross section of oxidized zirconium. Designations of phases given below this figure are the same as those used in the three-phase diffusion system represented by Fig. 5 in the following section. Zirconium oxidized for longer exposure times showed two types of oxides: white oxide at the surface and an underlaying layer of gray oxide. X-ray powder patterns of these oxides at room tern-

Jan 1, 1969

By F. A. Veer, W. G. Burgers, B. H. Kolster

Starting-- from Cu-Si diffusion couples a study of diffusion in the intermetallic compound Cu3Si of the Cu-Si system has been made. Mmker experiments showed copper to be the diffusing element. From the rate of growth of the Cu3Si phase diffusion coefficients were derived. The activation energy for diffusion is 18.6 kcal per mole. The couples show some interesting microscopic features, for which a tentative explanation is given. THE synthesis of dimethyldichlorosilane, (CH3)2SiC12, an important compound in the manufacture of methyl-silicones, takes place at the surface of a thin Cu3Si layer deposited on a mass of silicon particles."&apos; By passing CH3C1 vapor at about 350°C, silicon atoms are consumed from Cu3Si in forming the volatile silane molecules, thus leaving copper atoms at the surface. It is well-known that copper acts as a poison for the above-mentioned reaction by catalyzing the dissociation of methylchloride.&apos; However, no poisonous effect is observed, at least not before most of the silicon from the particles is converted into silane.3 This would be understandable, if either the copper atoms diffuse through the Cu3Si deposit to the underlying silicon or silicon atoms diffuse in the reverse direction to the copper, both processes resulting in the formation of new Cu3Si and so ensuring the proceeding of the reaction. In this paper experiments are described, demonstrating copper to be the diffusing element. Also a very low activation energy for the diffusion is observed. EXPERIMENTAL The silicon used contained 1 ppm Mg and 1 ppm Cu; the copper was spectroscopically pure (Fe: 2 ppm; Ag, Mg, Si: 1 ppm). The copper and silicon samples were prepared in the form of blocks of approximately 10 by 10 by 5 mm with two parallel sides by spark-machining. The blocks were ground on emery paper (grit 600), etched (copper with nitric acid, silicon with a 4:l nitric acid:hydrofluoric acid mixture), and cleaned with alcohol. As the brittleness of the silicon did not allow a welding procedure to prepare the diffusion couples, the copper and silicon blocks were pressed together in a steel clamp. The pressure exerted by the clamp brought about contact between the parts of the couple and so ensured proceeding of the diffusion. The couples were heated in a vacuum furnace (about 10"5 Torr). The temperature was stabilized within 1 pct. After a heat treatment a section parallel to the direction of diffusion was examined in the microscope and in the X-ray scanning microanalyzer. To determine whether copper or silicon is the diffusing element marker experiments were carried out using tungsten wires with a 20-p diam. EXPERIMENTAL RESULTS Figs. 1, 2, 3, and 4 give micrographs of diffusion zones of Cu/Si couples. Analysis by the electron mi-croprobe of the Cu/Si samples after a definite heat treatment revealed the existence of only one intermetallic phase as can be seen from the line scan shown in Fig. 5. From the X-ray diffraction pattern it could be deduced that this phase was CU 3 Si.4 Even when diffusion zones of considerable width (up to 600 p) were obtained, no other phases occurring in the Cu-Si system could be detected, neither by the electron microprobe nor by X-ray diffraction analysis. The optical anisotropy of the Cu3Si phase made it possible to observe the columnar shape of the crystal-

Jan 1, 1969

By Owen F. Jensen

CONSTRUCTION of a ground-water supply includes many operations, which do not end with completion of facilities. Evaluations must be made of the quality of water in various areas and the history of production. Following an analysis of geologic, hydrologic, and chemical data there must be an exploratory drilling program and a study of resulting information. When the well is completed a continuous survey of operating records and basic data is necessary, since designs for future wells are varied as more data becomes available for those already completed. As the following discussion must be limited to a single undertaking, the customary procedure will be outlined for development and construction of a ground-water supply in which more than three wells are involved. Parts of this procedure are applicable for all ground-water supplies. Three possible sites were selected for construction of a paper mill. The problem was that the industry daily required approximately 15 million gallons of water of the best quality available; however, if water of the best quality were not available in the desired amount, water of a poorer quality could be used up to half the required amount, about 7 million gallons. In the preliminary survey approximately 1500 to 2000 square miles were covered for each site. Collected data consisted of several hundred electric logs of oil and gas wells; reports by the U. S. Geological Survey on ground-water resources of localities in and near the area; unpublished records of several hundred water wells including chemical analyses of the water produced and drillers&apos; logs of the wells; records of periodic water-level measurements made in observation wells by the USGS; topographic maps drawn up by USGS and by army engineers; and highway and county road maps. A preliminary report based on study and evaluation of these data was presented to the client, recommending the site with the most favorable and economical ground-water conditions. The study indicated that water of the quality and quantity desired could be developed. In this particular area there were indications that the aquifer could be separated into two zones con- taining water of different chemical character. This chemical character varied somewhat with area, but principally with depth, a factor which later proved an economic advantage in design of the well field. After studying the preliminary report, the client weighed other economic factors as well as ground-water advantages and selected a plant site. Authority was given to proceed with detailed study of the chosen area. Evaluation of preliminary data concerning the area indicated that it should be supplemented with additional information derived from actual exploratory drilling and testing. A flexible plan of exploratory drilling was devised so that data obtained as each test hole was drilled could be correlated with existing data and additional test holes could be located and drilled accordingly. Specific data to be obtained from each test hole were: samples of all formations penetrated; the driller&apos;s descriptive log of formations; electric logging surveys; one or more samples of water from selected water-bearing formations; temperature; and water levels and their recovery after periods of production. The area studied in such detail was approximately 400 square miles. Choice of location for the original test holes was based on the preliminary study. The pattern for these test holes was designed to require a minimum number of holes and to allow for interpolation of data between two, three, and four holes. Geologic, hydrologic, and chemical data gathered after completion of the first four test holes showed that the north section was the most desirable in the area, which was then reduced from the original 400 square miles to about 150 square miles for more detailed and intensive study. On the basis of findings from the current test a tentative well field was laid out and a drilling program devised. One test hole was located on the actual plant site and later developed into a small pilot production well equipped with a deep well turbine pump. Water from this well was used for general construction requirements. Another test hole drilled near the pilot production well and adjacent to the proposed route of the well-collection system was used during the pumping test of the pilot production well to determine the degree of interference. From the data thus obtained, calculations were made to determine the coefficients of transmissibility and storage. Three additional holes

Jan 1, 1955

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250&apos; and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

By Leons Kovisars

Introduction Competitive analysis is the collection and evaluation of data on a product, a product line or on an entire industry. Much of the focus of competitive analysis centers on production volume and the price targets of the competitors. In actual practice capacity may be used in place of production volume. Similarly, unit production costs and individual producing units - mines, mills, smelters, refineries - may be the targets of the analysis. The purpose of competitive analysis is to provide information for strategic planning. The analysis will locate the position of the company in the industry and define the competitive margin -- or lack of a margin - between the company and other producers. The analysis can show the current situation and may be expanded to examine the outlook for the future. The forecast option is particularly valuable because it will show the opportunities for new project development or the expansion of current production. Similarly, the forecast will show the potential threat from new entrants, and may provide early warning to reconsider operations that may become uncompetitive in the future. Production cost analysis is a clearly understood means to evaluate producers and estimate the outlook for their profitability. The cumulative cost for the industry outlines the supply structure and defines the marginal cost of production used in developing price forecast as explained in the sub- sequent section of this paper. Competitive analysis is particularly important to the mining industry, notably to metal producers. The final product is typically a purified metal conforming to standards, and interchangable with the output of other producers, i.e. a fungible commodity. Brand loyalty is questionable in the mineral industry. Consumers will show a preference for specific brands, but this preference will be limited to a premium of several percent over the general market price. Price and assurance of supply are the keys to marketing success. Assurance of supply depends on geopolitical considerations and production capabilities. Price will be closely related to cost of production and a thorough competitive analysis should describe the cost structure of the industry. This snapshot will locate one&apos;s own position and provide an immediate and readily understandable evaluation of the hazards and opportunities inherent in this position. In the following section we shall discuss elements, methods and sources for competitive evaluation. ELEMENTS OF COMPETITIVE ANALYSIS The practice of systematic collection and analysis of data on competition is hardly a new concept; see, for example, Wall (1) or Porter (2). However, most discussions have been in the context of conventional industrial or manufacturing industries, with a focus on product lines and brand marketing. These considerations are not irrelevant to mining but they do have only a limited application. The key to success in the mining industry is minimizing the cost of production. However, this simple concept becomes complex when we consider relevant costs and the planning horizon. Production costs include the factors consumed in production, namely labor, fuel, energy, materials and supplies. The cost also includes purchased and contracted services such as freight, smelting and refining, sampling and sales required to convert ore to the finished metal. Royalties and ad valorem taxes paid on gross production are direct expenses, as is the cost of administration required by the production units. The sum of these outflows is the total cash cost, the expense that has to be paid in cash in order to continue production. Indirect costs incurred by a producer will commonly include allocated headquarters expenses, as well as the capital charges associated with equity investment and debt. Profit is not generally considered an indirect cost even though it represents the cost of using the owner&apos;s capital; similarly, income taxes represent the government&apos;s participation in the profits of the enterprise. Interest payments are considered as a direct expense in some cost studies, but many competitive evaluations would consider

Jan 1, 1985

By J. J. Taber, W. K. Meyer

Experiments on consolidated sandstones have shown that a variety of conditions are responsible for the wide range of behavior observed when oil and water are displaced simultaneously by a solvent which is miscible with both. The type of displacement is influenced most strongly by the relation between the plait point of the ternary phase diagram and the composition path followed by the system as it achieves mis-cibility. Neglecting viscosity, the displacement becomes less efficient as the distance between the composition path and plait point is increased in either direction so that a very wide spectrum of displacements is possible with different alcohol, oil and brine systems. It is possible by choosing various composition paths as miscibility is achieved to exercise some control over the actual displacement mechanism. Control over the composition path is exercised by adding oil or water in specific amounts to the alcohol prior to its injection into the porous medium. This technique apparently makes it possible to obtain piston-like displacements with systems which are usually characterized by the efficient displacement of only one of the two phases i.e., either oil or water, while the other phase lags behind. However, the simultaneous displacement of oil and water is not as efficient as other miscible displacements at a similar mobility ratio. The evidence indicates that both oil and water "leak" into the alcohol "piston" in compensating amounts. With oils of low viscosities the displacement is inefficient because the low oil saturation in the stabilized bank causes oil to be trapped by water before miscibility is attained. INTRODUCTION The simultaneous displacement of oil and water by solvents such as alcohol has been investigated in the laboratory and in the field. The laboratorv workers investigating all-liquid miscible systems have recognized the great importance that the nature of the traingular phase diagram exerts on the efficiency of the miscible displacement. Gatlin and Slobod pointed out that displacement efficiency will be improved if miscibility can be retained for long periods and that this behavior tends to be followed if the applicable phase diagrams have very low binodal curves. In their unconsolidated sand tests the alcohol was considered an ideal miscible piston displacing both oil and water phases. Later workers have pointed out that an important feature of the phase diagram as far as oil recovery is concerned is the location of the plait point. This is particularly true in the case of consolidated Sandstone.3 Since the original discussion of this effect, the importance of plait-point location has been confirmed and discussed by other author The early workers394 recognized that the position of the plait point could be altered by changing the oil or the alcohol used in an experiment. In addition, recent work has demonstrated that the plait point can be shifted by altering the nature and concentration of dissolved salts in the aqueous phase. However, the entire scope of the relationship between displacement and plait point has not been discussed previously and a technique for changing the composition path as miscibility is achieved in a particular ternary system, i.e., oil, water and solvent, has not been demonstrated. * The importance of oil viscosity on the efficiency of oil displacement by alcohol has not previously been observed, probably because the range of viscosities used in earlier experiments was too restricted. It is the object of this paper to describe the relationships between the ternary phase diagram, fluid properties and the displacement achieved. A technique for controlling the nature of the displacement is also presented. THEORY AND DEFINITIONS PISTON-LIKE THEORY The theory of alcohol flooding has been discussed in some detail.2-4 The concept was advanced that

Jan 1, 1965

By P. E. Busby, C. Wells

FURTHER study of data used in determinations of 1—rates of diffusion of boron in austenite and 2—solubilities of boron in the a and phases of iron and steel&apos; has provided an equation for the diffusion of boron in a iron. In brief, the previously published data were accumulated from the results of deboron-izing (and decarburizing) experiments carried out in the range of 700° to 1300°C. Diffusion coefficients (D?) for boron in austenite were calculated using the Grube solution of Fick&apos;s law. However, only solubility values were estimated from the discontinuous concentration-penetration curves, Fig. 1, which are characteristic of diffusion in two phases. Dr. Carl Wagner&apos; has recently provided a solution for calculating D values from penetration curves of this type as follows: Cl1.1 —C8/C8- C11.1 = vp ? e ? erf (?) and D = ?/4?2 t where C11,12, C8, C11, and E have the values shown in Fig. 1. D is the diffusion coefficient, sq cm per sec; t is time of deboronizing anneal, see; and ? is a di-mensionless parameter. For a given diffusion experiment, the value of ? can be readily obtained by graphical solution from a plot of y vs the right-hand part of Eq. 1. D may then be evaluated from Eq. 2. The avplication of this solution to previously re-ported results, of which excerpts are given in Table I, permits the calculation of diffusion coefficients for boron in a iron. On the basis of these meager data, it is tentatively concluded that the diffusion of boron in a may be represented by the equation Da = 1011 e-92,900/RT where R is the gas constant, cal X 0C-1 X mol-1; and T is the absolute temperature, OK. Although the frequency factor, 106 sq cm per sec, is admittedly several orders of magnitude higher than expected, the value of Q, 62,000 cal per mol, appears reasonable and is, in fact, very similar to that for the self-diffusion of iron. It is pertinent to mention at this point that the value of Q obtained for the diffusion of boron in austenite by means of the Wagner solution is 19,000 cal per mol and is in excellent agreement with the value previously reported1 in the equation DT = 2xl0-3 e-21,000/RT [4] which was determined by the application of the Grube solution to other data. The fact that determined constants A and Q in the equation D? = A e-Q/RT were practically the same, independent of whether the Wagner or Grube solutions were used in determinations of D values, strengthened the authors&apos; belief that the computed values of D (Table I) using the Wagner solution are reliable. The relative values in Eqs. 3 and 4 for the diffusion of boron in the a and ? phases, respectively, suggest that boron forms a substitutional solid solution in a iron and an interstitial solid solution in ? iron. The same tentative conclusion has been reached by McBride et al.3 on the basis of relative solubilities, atom diameter, and the size of the interstitial hole in a and ? iron. In connection with the data for test 14 listed in Table I, it is of interest to calculate the solubility of boron in a iron using the D value given by Eq. 3. As might be anticipated from the small movement of the interface in test 14, proper substitutions in Eqs. 2 and 1 give a low value, approximately 0.0004 pct B, at 850°C. Apparently at 835°C (test 13) it is possible to obtain 0.0018 pct B, and at 850°C only 0.0004 pct B into solution in the a phase before a second phase appears. These observations are consistent with the Fe-B constitution diagram proposed by McBride, Spretnak, and Speiser.3 References P. E. Busby, M. E. Warga, and C. Wells: Diffusion and Solubility of Boron in Iron and Steel. Trans. AIME (1953) 197, p. 1463; Journal of Metals (November 1953). &apos;W. Jost: Diffusion in Solids, Liquids, Gases. (1952) pp. 69-71. New York. Academic Press Inc. "C. C. McBride, J. W. Spretnak, and R. Speiser: A Study of the Fe-Fe2B System. Trans. ASM (1954) 46, p. 499.

Jan 1, 1955

By E. D. Gardner, E. M. Sipprelle

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321-325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale deposits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 90 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;&apos; the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surfac,e samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name "oil shale" is unfortunate, as the rock is a tough, strong marlstone. Organic matter named "kerogen" is a constituent of the rock. The oil-shale demonstration mine is on Naval Oil-Shale Reserve No. 1; it is about 5 1/2miles by mountain road from the plant site, which, in turn, is 2 miles from U.S. Highway 6 and 10 miles west from Rifle, Colo. The highway parallels the Colorado River, the Denver and Rio Grande Western Railroad, and a 66,000-volt public-utility power line. Early in the program it was realized that an oil-shale enterprise would have to be on a large scale to be commercial, and that unusually low mining costs would be necessary. The physical characteristics of the Mahogany Ledge and an overlying roof stone are unusually favorable both for large-scale operation and low mining costs. Quarry practices largely will be followed underground to mine the Mahogany Ledge. The aim has been toward complete mechanization of all mining operations. A mining unit would comprise a square mile containing 100,000,000 tons of oil shale with allowance for mining losses. An investment of $1,000,000 would be $0.01 a ton; such an expenditure, therefore, could be made to save, say, $0.015 per ton daily operating cost. A goal of a mining cost of $0.50 per ton was set up in 1945. Open-cut mining costs then were about $0.25 per ton of material handled; it was hoped that a cost double this amount could be obtained in mining the Mahogany Ledge. Costs of labor and supplies have increased since 1945 and so has the selling price of petroleum products. To those unacquainted with the character of the Green River deposits, the name "shale" suggested high mining costs. Others assumed that coalmining costs of $2 to $5 per ton would apply. To many, the expected mining costs appeared the principal handicap to the establishment of an oil-shale industry. The purpose of the Bureau of Mines is to demonstrate methods and to establish costs for mining the oil shale on a large scale. It is hoped this work will lead to the establishment of a large-scale, commercial oil-shale enterprise.

Jan 1, 1950

By Dick Whittington, W. R. Taylor

GENERAL In mid-1974, a representative of ARCO Petroleum Company walked into our Austin offices and asked for a permit for ARCO&apos;s first Clay West Mine site. This was the first in situ uranium mining permit issued in the United States. That initial permit, issued in January 1975, was for three acres. The four years since have been characterized by growth and change. Today there are 16 permits approved for approximately 1,540 production acres issued to five companies at eight sites in four counties. There are approximately seven additional permit applications being processed or on the verge of being submitted for an estimated 2,000 additional acres of production. As a rough gauge of the financial scope of this activity, at the typical 40 production wells per acre and an estimated $2,000/well, operators hale installed or committed $122 million for production wells. This does not account for the exploration and development wells installed to delineate the ore or the cost of processing facilities for extracting the uranium. HISTORY OF URANIUM MINING IN TEXAS Information I have concerning early in situ uranium mining activities is "sketchy" but the apparent first on-site test of in situ uranium mining was conducted between 1967 and 1971 at the Dueterstat site, north of Yorktown in Gonzales County, by City Service. Others ran tests at the Bruni site in Webb County and the Burns and Clay West sites in Live Oak County in the mid-70&apos;s. During this period, Texas Water Quality Board personnel in the central and district offices maintained a general surveillance of these various test activities. Regulation of in situ uranium mining was formalized with the issuance of a permit in January 1975 with the advent of ARCO&apos;s initial production scale (3 acre) effort in the Clay West area at the Moser mine site. Since 1975, the accelerating rate of mining and exploration activity is noticeable. There were 16 exploratory rigs operating early in 1977. This year, the rig count is averaging 46--a 287% increase. HISTORY OF LEGISLATION Paralleling this mining activity was state and federal legislation which subjected in situ mining to environmental regulation. The following is a brief chronology of the legislation that is directly or indirectly related to uranium mining. As most of you know, disposal wells are an integral part of most in situ uranium mines operating in Texas. They are used both during production and during aquifer restoration following production. The wells are regulated by the Texas Injection Well Act, enacted in 1961 by the Texas Legislature. In 1967, the Water Quality Act established the Texas Water Quality Board, and provided for the regulation of water quality by the so-called permit system. In 1969, the Solid Waste Act was enacted by the Texas Legislature. The legislation provides for control of wastes from manufacturing, mining, and agriculture. This Act regulated uranium surface mining activities until 1975 when the Texas Surface and Mining Reclamation Act placed responsibility with the Railroad Commission for uranium open-pit mining and surface mining of coal and lignite. In 1972, the Federal Water Pollution Control Act (Public Law 92-500) was passed. This legislation forms the legal base for the NPDES (National Pollutant Discharge Elimination System) and the subsequent point source effluent guidelines and standards. The November 6, 1975 issue of the Federal Register published interim final rules for Best Practical Treatment levels for effluent discharges from ore mining and dressing operations. Litigation was immediately initiated by eleven companies against these proposed rules, and they are currently being reconsidered for reissuance in 1979. In 1974, the Federal Safe Drinking Water Act (Public Law 93-523) was enacted. A part of this legislation is the Underground Injection Congrol Program. The regulations implementing this program have undergone various public hearings and it is expected that they will be published in the Federal Register before the end of 1978. In 1975, the Texas Surface Mining and Reclamation Act (Senate Bill 55), providing for the Railroad Commission&apos;s authority to require reclamation of surface mines, was passed. In 1977, an amendment to Senate Bill 55 was introduced that proposed to place regulation of in situ mining of coal, lignite, and

Jan 1, 1979