Search Documents

By G. A. Vissac

IN the presentation which follows, washability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. FLOAT-AND-SINK TESTS For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve "-a somewhat misleading term-will be considered. Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. NEW FORM OF GRAPHIC PRESENTATION The resemblance of the recovery curve in Fig. I, or, for that matter, the recovery curve obtained in common practice, to a power curve is apparent. The general equation of such a curve is y = axn where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis, the recovery graph will be a straight line, using the same variables as in Fig. I ; namely, the ash con-

Jan 1, 1942

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a [?] line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and [?] lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz," This would require many data to prove, but no proof is given; any considera¬tion would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.¬Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg8 have ground

Jan 1, 1941

By John J. McCabe

INTRODUCTION Over the years, Congress has written into the Internal Revenue Code various provisions aimed at lessening at least one financial burden faced by taxpayers in the mining industry - the federal income tax burden. These provisions include the election to deduct exploration expenses, the election to defer deduction of development expenses, and the percentage depletion deduction. Careful tax planning from the very beginning of a mining venture is essential in taking maximum advantage of these tax benefits. A major decision to be made is the choice of organizational structure. (For a more detailed discussion of this subject, see McCabe, John J., "Developing Structures for Investments in Mineral Property," New York University Institute on Federal Taxation, 42 NYU 24, 1984). One such structure is the use of multiple corporations, with mining activities conducted by one corporation and nonmining activities, such as manufacturing, financing and administration, conducted by the other corporation. This technique, which will be discussed in detail below, can be particularly advantageous in delaying recapture of previously deducted exploration expenses and in maximizing depletion deductions. TAX BENEFITS IN MINING Exploration Subject to certain restrictions discussed below, exploration expenditures (i.e., expenditures paid or incurred during the taxable year for the purpose of ascertaining the existence, location, extent, or quality of any deposit of ore or other mineral, and paid or incurred before the beginning of the development state of the mine are deductible at the election of the taxpayer (Section 617(a)).* Were it not for this option, exploration expenditures would be required to be capitalized and recovered through depletion, after production begins. Exploration of a mineral deposit can be very costly and may not result in commercial production for some time. If the taxpayer has income to he offset by the deductions, a mining venture can usually be structured in such a way as to allow the offset of mining losses against the other income. With today's high interest rates, this election can be quite valuable in present value terms. Corporate and noncorporate taxpayers are subject to different restrictions on this tax benefit. Corporations may elect to deduct only 85 percent of eligible exploration expenditures (Section 291(b)). (The Tax Reform Act of 1984 reduced this to 80 percent effective for expenditures after December 31, 1984, in taxable years ending after such date). The remaining 15 percent (20 percent after December 31, 1984) is capitalized and recovered at the same rate as five-year ACRS property (Section 291(b)). Individual taxpayers are not subject to this 85 percent rule; however, any amount deducted in excess of ten-year straightline amortization is a tax preference item for individuals (Section 57(a)(5)). Individuals may avoid the tax preference by electing to capitalize exploration expenditures and amortize them over ten years (Section 58(i)). In order to prevent the taxpayer from, in effect, converting ordinary income into capital gain by selling property that has given rise to exploration expense deductions, the Code requires recapture of such deductions upon the occurrence of certain events (Section 617): 1. Upon disposition of the property, adjusted exploration expenditures are recaptured to the extent of gain realized on the disposition (Section 617(d)). 2. If the property is leased, the lessor is disallowed any depletion deduction until his adjusted exploration expenditures have been recaptured in the form of foregone depletion deductions (Section 617(c)).

Jan 1, 1985

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By W. H. Newhouse

DURING the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth's crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions.

Jan 1, 1931

By Thomas T. Read

Mining, which is at least twenty cen-turies old, was at first, and long, wholly a practical art. Little more than two centuries have elapsed since the inception of the idea that general education and a knowledge of natural science would be of advantage to those engaged in the mining industry. Though schools of mining began to develop in Europe early in the eighteenth century the concept of educational preparation, for technical conduct of the industry was slow in winning general acceptance in the industry itself. John Hays Hammond, in his autobiography, recalls that when he sought employment with a mining company after he had graduated from Yale and Freiberg he had to assure its executive, before being even considered for employment, that he did not consider that he had learned anything about mining. This was as late as 1880. Existence in the industry of a prejudice against education of the academic type is perhaps an explanation why inadequate provision has been made by the mining industry for the continuing education of technical employees after they enter employment, although engineering education prior to engaging in industry has now won general acceptance. I am familiar with the existence of 'loop" courses for engineering graduates in metallurgical plants, of schemes for giving mining graduates "practical experience," and of the interest in vocational courses for workmen which sprang up in the period of labor shortage during and immediately following World War I (but which quickly died when the depression of 1921 again made experienced workmen available in sufficient supply), having been chairman of a committee appointed by the Mineral Industry Education Division to make a survey of existing provisions for post-employment training for engineers in our industry. The results of that survey, reported elsewhere, clearly indicate that it is inadequate as to amount; the aim of this paper is to present evidence for belief that it is also inadequate in quality. To avoid becoming too involved, no reference will be made here to post-employment vocational training for workmen, which is a subject differing so much from post-employment education for engineers as to require separate treatment. Neither will postgraduate education for metallurgical engineers be discussed, becadse a distinction must then be made between training for research work and for plant operation, whereas mining engineers engage almost exclusively in operations. Since the situation in the coal-mining industry has been discussed at several recent meetings, that also will be passed over, and what follows should be taken as a discussion applying exclusively to the metal-mining industry. Professional Development In the operations field (both in mining and metallurgy) the work to which a beginner is assigned is seldom closely related to previous academic education. The contrast is almost as great as between

Jan 1, 1943

By James J. Wise

INTRODUCTION One basic design feature utilized in all caving and sublevel stoping techniques is the drawpoint. These draw- points may be located on sublevels when using sublevel caving methods, or may be located at the floor pillar when using block caving, sublevel stoping, or vertical crater retreat methods. How the drawpoint is designed and developed, how the ore is withdrawn from it, and how the ore is hauled to the shaft or portal encompasses the loading and hauling function. Historically, predominate loading and hauling equipment for caving and sublevel stoping has been scraper slushes, air powered overshot loaders, and rail mounted train haulage. All of this equipment has two common constraints. 1. The equipment locked into specific work sites and is not easily shifted to another work site. This constraint can often lead to low utilization and low productivity of the equipment. 2. The equipment is designed to work in the horizontal plane, which requires that the various horizontally-oriented working levels be connected by vertical raises. Vertical development by means of raises is not only increasingly expensive, but also is not well adapted to movement of large equipment into the s topes. In the last 20 years, two revolutionary labor saving concepts have become common in caving and sublevel stoping. 1. Long-hole drilling, which has mechanized the development of the drawpoint extraction structures as well as the actual stoping and undercutting. 2. Vertical access by means of trackless ramps between levels, and the consequent use of rubber-tired vehicles not only for loading and hauling ore, but also for the rapid movement of men, material, and equipment into the stopes. The introduction of trackless mining systems for loading and hauling has not been easy. Mine planners have had to re-orient their thinking to the larger operating space required by trackless equipment. Larger access drifts have necessitated reconsideration of mine layouts to insure proper ground support. Spiral ramp developments were often laid out on slopes steeper than the equipment could negotiate economically. Mine operators had to accept the added responsibility of roadway maintenance, water removal, increased ventilation, and more technical mechanical maintenance. As the mine operators enthusiastically embraced the superior productivity of trackless mining systems, they some- times disregarded opportunities to combine the older types of equipment with trackless vehicles to maximize productivity at lowest cost. In order to gain a proper perspective on this problem, it is necessary to review the various techniques of loading and hauling and to become more aware of the advantages or disadvantages that each system or combination contributes. LOADING Loading consists of two functions, (1) primary loading from a drawpoint and (2) secondary loading into long- haul system, a truck, train, or possibly a belt conveyor. Mine planners have four basic loading systems available to fit various operating conditions. These are, (1) gravity, (2) scrapers, (3) rail-mounted loaders, and (4) trackless loaders. Each system can produce optimum results under specific conditions. Gravity Loading Gravity loading is probably the oldest system in general use today.

Jan 1, 1981

By Paul A. Schafer

BALATOC mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.1 The region is a deeply dissected plateau, ranging in altitude from 3000 t0 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. 1): q6, 231 and 364, which strike about N.70°E. and dip 5o to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.45°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. NORTHEAST FAULTS The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on Pine fault and q6 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar No. I, and Sun

Jan 1, 1942

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

The work of the Committee on Industrial Preparedness* is well summed up in the following letter written by Thomas A. Edison, Chair-man of the Naval Consulting Board, after President Wilson and signed the army appropriation and army reorganization bills: "The Committee on Industrial Preparedness of the Naval Consulting Board, of which committee Howard E. Coffin is chairman, after a five months' campaign in many ways unique in vigor and vision has played a very definite part in the measures for the national defense which have just become law. It is responsible for having laid the foundation for a true industrial preparedness in this nation. "Five months ago the committee, wholly non-partisan in make-up, acting with the civil, mechanical, mining and electrical engineers and the chemists of the country, members of five great scientific bodies, began its work in' every nook and cranny of the land. The purpose was to prepare American industry efficiently to support the armed forces of America in the event of war. "The public, the business men and the legislators at Washington knew little regarding the demands on industry in connection with modern war. No department at Washington was charged with the duty of coordinating the needs of the army and navy with transportation, industry, and kindred functions. The purchasing, quartermaster's and ordnance departments of the army and navy were unable to buy military supplies except by competitive offering in the open market. No one had considered the need, and no legislative machinery was in existence, for preventing the presence of skilled workers on the fighting front when they would in time of war be needed in the factories, mills and mines of the country. Neither at Washington or elsewhere was there even a list of the industrial resources of the nation in such shape as could be used for practical purposes in case war should come. "The three things, then, that the committee headed by Mr. Coffin set out to do and that now have been brought about were as follows: First, to mobilize concretely the business men of America and their output against a day of need. This meant chiefly to discover in fullest detail just what equipment our manufacturers possessed that might be swung over to supply the army and navy swiftly and bountifully from the hour the colors were raised. In a few weeks this initial task, which has been a truly colossal one, will be at an end. A complete report of the equipment of practically every concern of substantial size in the country is now in the hands of the - committee. Directly in charge of the great inventory has been W. S. Gifford, Supervising Director of the Committee. The second step was to procure legislation making possible the placing by the war and navy departments of annual orders for munitions in small quantities to American manufacturers now not producing such things, so that quietly, efficiently and thoroughly they could learn in time of peace how to supply the government in time of war. The new laws make all this possible. It should be said here that this practice will bring about a geographical diffusion of munition plants all over our country, instead of affording us only a few such concerns for the most part near the exposed seaboards, as at present. It is obvious that this system will also throttle all talk of a munitions trust.

Jan 10, 1916

By Brooks J. Klimley, Daniel M. Higgins, Grover R. Castle

Measuring The Economic Viability Of Resource Projects (A Western Surface Coal Project) The bankers approach to the analysis of a new "green fields" mining project is similar but different from the approach that the pining company might take. The purpose of this paper shall be to discuss the techniques that are used by mining companies and bankers as they try to measure the economic viability of mining projects. The analysis of these new projects (by both the mining companies and the banker) is based on a projected revenue stream and not on historical earnings or past perfomance because these projects are start up situations with no history to look to. The starting point in the analysis of these projections is the choice of the assumptions to be used in preparing these projections. After the assumptions have been determined and the projections are prepared then the projections are submitted to various tests in order to determine whether the project measures up to previously agreed upon minimum standards. In order to illustrate the analytical procedures used in evaluating a mineral project the writer has constructed a hypothetical case involving the development of a western surface coal mine (Property). The basic data in connection with this hypothetical new project is described in the next section of this paper. After the Description of the Project is a section which shows the type of analysis that a mining company might prepare in order to approach a bank for a loan and the final section illustrates the type of analysis that a bank might prepare in evaluating this loan request. Description Of The Project or Basic Data In Connection With Undeveloped Western Surface Coal Property An independent mining/geological Consultant's report has been completed on the Property which confirms that the Property contains 175 million tons of economically recoverable coal subdivided into the following reserve categories in accordance with U.S. Bureau of Mines and U.S. Geological Survey definitions: Measured or Proven 90,000,000 Indicated or Probable 50,000,000 Inferred or Possible 35,000,000 The owners of the reserves have chosen to drill up those reserves that are nearest to the subcrop and have not spent as much time on those portions of the Property which are on the fringes of the deposit where the overburden is thicker because the stripping ratio and hence the operating costs and capital requirements are higher down dip. The proven reserves are based on an average thickness of 80 feet, of which a mining recovery of 90% is projected. The overburden thickness varies from 0' to 280' with an average thickness of 127'. The overburden consists mainly of scoria, sandstone, gravel, shale and silty clay. 134 holes were cored (and analysis done on five foot increments) in the measured reserve on the following spacing: 100 foot centers to define the burn line; 1,320 foot centers to define the early mining areas; 2,640 foot centers to identify the later mining areas.

Jan 1, 1985

By E. W. Davis

ABOUT a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½ -in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about zoo per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½ in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2 1/2 kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1945

By Arthur F. Taggart

ENGINEERING education today is like a crazy quilt of somber wools and gaudy shoddy, chain-stitched on an academic assembly line, and sold at ever mounting prices to inexperienced youths for lifetime use. Each engineering school offers a half-dozen or so patterns with essentially the same skimpy wool content. Sales appeal is in the color of the shoddy, denoted by the hopeful adjectives chemical, civil and the like. This article is argument for an all wool product made by slow, careful handwork. Bluntly it proposes a thorough four-year undergraduate drill in fundamental science and general engineering empirics, leavened by continuing study of the third of the engineer's troubles: Man. It is not contended that existing methods of engineering education have failed to start men on the path to successful engineering practice (too many of you have started that way); rather, social conditions and the bounds of knowledge have changed tremendously, and corresponding alterations in the pattern of engineering education are overdue. We'll Teach the Specifics The first part of this contention is illustrated by excerpts from a letter received recently from an officer of one of the largest corporations: "We are interested in employing two or three outstanding young engineers to be placed on a special training program to develop them as design and construction engineers.... "We propose to put these men on a four-month indoctrination and orientation course after which they would be given job-training assignments for a period that will vary from about six months to about a year and a half depending upon the aptitudes, abilities and intelligence of the candidates.... "I am not too fussy about what kind of engineers the men might be insofar as academic courses are concerned. They could be.. . in almost any engineering classification.... We can furnish the additional training beyond the academic fundamentals. "The starting rate for these jobs would be $326 per month...." This letter is not unique; rather it is representative of a practice that has become common. It is industry's enforced response to the general refusal by young graduates to submit to union domination in order to gain operating experience at the labor level. The message to engineering schoolteachers is plain: You teach the fundamentals; we'll teach our practice and pay the graduate to learn it. The letter means to the student that time spent in school studying the specific practices of particular industries is waste compounded. The school can't give the equivalent of what industry teaches, wherefore industry will still demand apprenticeship. The student must pay for the specific instruction at school instead of being paid to take it later. And time-consuming specifics crowd out drill in basic scientific and technical subjects as well as liberal arts.

Jan 1, 1952

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By H. Papazian, Robert A. Lad

SINCE it can be shown both theoretically'' : and experimentally that disordered Cu3Au has a greater internal energy than the ordered alloy, it might be expected that its chemical reactivity would be greater. Experiments were initiated' to test this hypothesis. This note will describe some recent results obtained in the study of the rates of corrosion of ordered and disordered polycrystalline Cu3Au by aqueous FeCl., The work of Robertson' has indicated that the attack by such solutions is intergran-ular and highly orientation dependent. It was of interest to see whether the order-disorder effect was great enough to overcome the variations from specimen to specimen which would arise from this type of attack. The polycrystalline alloy specimens (0.020 in. wire, 1¾ in. long) were preannealed in ½ atm H, at 700°C for 2 hr. The subsequent heat treatments to produce order and disorder were performed in M atm He. Disordered specimens were obtained by heating at 450°C for 2 hr and quenching in water. Ordered specimens were produced by heating for 2 hr at 450°, furnace cooling to 380°, and soaking at 380°C for 80 to 90 hr. Room temperature was reached by cooling to 150" at a rate never exceeding 7" per hr, and water quenching from 150°C. The specimens so produced exhibited electrical resistivities characteristic of the two states; of the order of 11.27x10 ohm-cm for the disordered, and 4.28x10 ohm-cm for the ordered specimens. The corrosion rates were studied at 30°C in ferric chloride solutions of several concentrations (?,¼, 1.5, and 1 molar). The specimens were attached to a stirrer during the tests. Tests were interrupted at intervals, and the specimen weight change was determined after washing and drying. Analysis of the solutions showed that the attack was limited to the copper. The higher corrosion rate for the disordered alloy, as illustrated in Fig. l, is typical of the results obtained. The effect of variation in ferric chloride concentrations is indicated in Table I for typical specimens. The variations in the ratio of reactivity for disordered and ordered specimens at the different concentrations are within experimental error, and the best value is estimated to be near 1.4. The experimental variation was due in part to the mode of attack, as mentioned, and in part to the fact that films were formed on the specimens under some conditions. Electron diffraction patterns of the films were very complex and indicated the presence of metallic iron, as did chemical analysis. In an attempt to eliminate the difficulties arising from the mechanism of attack, single crystal specimens were used. A greater reaction rate was again measured for the disordered specimens, but the reproduci-bility was no better than that for the polycrystalline metal. This would indicate that film formation was primarily responsible. It was concluded that the reaction with aqueous ferric chloride served to demonstrate that the reactivity of disordered Cu3Au is greater than that of the ordered alloy. However, the difficulties with film formation did not permit determinations of a precision great enough to warrant extension of the study to partially ordered alloy systems.

Jan 1, 1957

By Phillip Crowson

INTRODUCTION This discusses some of the economic risks and uncertainties which face any company investing in new mineral ventures. These differ mainly in degree rather than kind from other large capital intensive projects, except that economic risks are compounded with technical risks. Mines face a wide variety of physical risks, and in addition the ore reserves may not prove as ample, nor as amenable to treatment as the feasibility studies indicate. On the economic front, mineral projects are subject to risks of fluctuating prices and sales volumes, no matter where they are located, or how they are financed. Typically, they are heavy users of capital compared with their owners' internally generated funds. Long term debt of various types is still the favoured form of finance. A project's currencies and cost often differ from each other and from those of the parent company. Facing up to the various risks associated with fluctuating and uncertain revenues, interest rates and exchange rates are amongst the hardest tasks for natural resource companies. ATTITUDES TO THE MINING INDUSTRY Some have questioned whether the game itself is now worth playing. They have argued that the mining industry's mediocre rewards in the past decade have been insufficient, compared with the risks involved. They can see no prospect of dramatic improvement in the next decade. Demand is highly cyclical and tends to grow less rapidly than economic activity, as a whole. Barriers to entry are low in most mineral markets, but impediments to exit can be substantial. Exit is especially problematic in those minerals where there are large state shareholdings and/or where less developed countries are major producers. The consequence is claimed to be an endemic tendency to excess capacity, and prices barely adequate to cover marginal cash costs. Many of the petroleum companies that moved into mining with such high expectations in the late 1970s have retreated, often bearing the scars of heavy losses. Individual shareholders, taken collectively, place low valuations on their investments in mining companies. The price/earnings ratios of the major mineral producing companies are low compared with their historical averages and with those of other industries. PRICE: EARNINGS RATIOS (October 1988) [UK Industrials 12.0 RTZ 8.4 Cons Gold 12.2 US Industrials 13 - 13.4 Alcan Alcoa Amax Asarco Cyprus Minerals Freeport Copper Inco Inspiration Magma Copper Newmont Mining Nord Resources Phelps Dodge Reynolds Metal Canada TSE 300 10.6 Cominco 8.7 Falconbridge 5.3 Noranda 7.0 Rio Algom 7.2 Teck Corporation 17.] NOTE: Mining companies' p/e based on prospective 1988 earnings, from Kleinwort Benson Securities' weekly Mining World, October 1988. Until 1987, it was argued that share prices correctly reflected the companies' poor earnings potential. Subsequently, the argument has been that earnings have been unnaturally boosted by cyclically high metal prices. The stock market valuations, therefore, correctly reflect future earnings, or at least expected earnings. This seems to be a case of Heads, I win; Tails, you lose. The underlying analysis of metal markets appears

Jan 1, 1990

By R. E. Caffrey, S. K. Tung

This paper reports some of tile results obtained from the vapor-phase reaction of a volatile metal halide with a hydrogen and carbon dioxide mixture in an epitaxial-deposition chamber. Tile oxides deposited were silicon di oxide, aluminum oxide, mix-12tves of silicon di oxide and aluminum oxide, and titanium oxide. Tile deposited silicon di oxide was transparent and amorphous and had a density and index of refraction similar to that of thermally grown silica. The vote of etching was determined. The thickness uniformily of the oxide was found to he related to the aerodynamics of the system employed for deposition. A clear silicon di oxide layer was found to be dependent upon the quality of the surface prior- to aside deposition. The process parameters affecting the vale 0f deposition were studied. The deposited aluminum oxide was transparent, holy-cl-ysttrlliile, and possessed remarkable resistance to hydrofluoric acids. By measurements it has been shown that the deposited aluminum oxide is both insulating and continuous. ThE cleanness of an epitaxial silicon surface both immediately after growth and during device processing is thought to be one of the major factors contributing to the electrical properties of a final device. The advantage of protecting an epitaxial silicon wafer surface with an oxide grown immediately following epitaxial deposition is obvious. The successive growth of silicon and silicon diox- ide in epitaxial apparatus was studied by Steinmaier and loem.' They formed silicon dioxide films on a silicon substrate by adding water vapor to the silicon tetrachloride-hydrogen mixture in an epitaxial system. They also showed that, when a gaseous mixture of carbon dioxide and hydrogen is injected, water is formed only at elevated temperatures. Thus the reaction of water vapor and silicon tetra-: chloride will be limited to a relatively small reaction zone near the substrate. This paper reports some results of oxide films obtained from a vapor-phase reaction of a volatile metal halide with a hydrogen and carbon dioxide mixture in an epitaxial-deposition chamber. EXPERIMENTAL APPARATUS The system employed for the oxide deposition is a modification of a vertical system used to produce high-resistivity silicon layers by the hydrogen reduction of silicon tetrachloride.' The modification shown schematically in Fig. 1 consisted of an additional carbon dioxide gas stream which entered the reaction chamber with a hydrogen stream saturated with metal halide vapor and a diluting hydrogen stream. Silicon dioxide layers made from a mixture of silicon tetrachloride, hydrogen, and carbon dioxide gases will be discussed first. EXPERIMENTAL RESULTS 1) Factors Affecting the Rate of Oxidation. An epitaxial silicon layer was deposited by the hydrogen reduction of silicon tetrachloride on an n-type,

Jan 1, 1965

P. W. BRIDGMAN.-Owing to a misunderstanding, I did not see Dr. McAdam's and Dr. MacGregor's remarks on my paper on Flow and Fracture (Metals Technology, December 1944, Pp. 32-38), until after their publication. Both Dr. McAdam and Dr. MacGregor speak of my analysis for the stress distribution at the neck of a tension specimen as containing several assumptions; in particular, that the strain is uniform across the section of the neck, that there is no hoop tension at the periphery, and that the plasticity conditions of von Mises hold. As far as the mathematics goes, the situation is no different in this problem of plastic flow than in a conventional problem of elasticity. That solution is unique which satisfies the boundary conditions on the stresses, the stress equations of equilibrium, and in addition the constitutive equations connecting stress and strain in the elastic case, or a corresponding set of equations, of which the von Mises relations are a special form, in the plastic case. In the particular case of the necked tension specimen I have found that there is a solution satisfying the boundary conditions, the stress equations of equilibrium, and the von Mises plasticity conditions in which the strain is uniform across the section, and there is no hoop tension at the periphery. This is therefore the solution, and the uniformity of strain and vanishing of hoop tension at the periphery are to be described as discoveries, over which the operator has no control, rather than as assumptions. The only part of the solution that can properly be described as an assumption is the von Mises plasticity condition. With regard to this it is to be noted that the condition is needed only in a much weakened form, for the analysis uses the condition only at the neck, where the strain is approximately constant. Thus, in the extreme case referred to in a footnote of my paper (p. 37, Met. Tech. Dec. 1944) the actually measured strain across the section varies from 2.4 to 2.6. Obviously it is a much weaker assumption to postulate that the von Mises condition holds in the strain range 2.4 to 2.6 than to assume it to hold for the entire range of strain from o up to 2.6, which would be necessary if the solution applied to the entire tension specimen rather than to the immediate region of the neck only. Furthermore, it is to be commented that under the special conditions of this problem the von Mises condition becomes identical with the maximum shearing-stress criterion of plastic flow; this amounts also to a weakening of the restrictions imposed by the von Mises condition. Dr. MacGregor refers to actual experiments of his own in which the strain was found not to be uniform across the neck. It is to be emphasized, however, that these were experiments on bars of rectangular section, and that the nonuniformity established was a nonuniformity around the perimeter, not a nonuniformity from the surface toward the axis. My method of solution applies only to a circular cross section. It can be said that the solution that satisfies the boundary conditions, etc., would definitely not be expected to demand a uniform strain for noncircular sections. In discussing my results, Dr. McAdam uses a definition of "flow stress" different from mine, so that the immediate applica-

Jan 1, 1945

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By Richard M. Foose

Most of the roofing granules produced in Pennsylvania are made by two companies at three plants. The Advance Industrial Supply Co. has three quarries and a mill at Gladhill Station, in southern Adams County. The Funkhouser Company is actively engaged in mining, quarrying and milling at Charmian, about one mile west of Gladhill Station, and at Delta, in southern York County. These three plants produced approximately 100,000 short tons of granules in 1943. The production of rooling granules in 1937 for the whole country was only about 500,000 tons, generally indicating the large growth of the industry since that time. The fundamentals of producing roofing granules were discussed comprehensively by G. W. Josephson in a paper before the Industrial Minerals Division in October 1943 (TP 1725, this volume page 460). The purpose of this paper is to describe the actual methods of mining the rock and milling it to make roofing granules, as practiced by the three Pennsylvania plants. Mining and Milling Funkhouser Company (Delta) The Funkhouser Company, near Delta, in southern York County, Pennsylvania, operates three joined quarries and a mine in the Peach Bottom slate. The joined quarries extend 1200 ft. in a northeast-southwest direction along the strike of the slate cleavage and are about 200 ft. .wide. The working face is about 45 ft. high. The quarrying operation is rather simple: Ingersoll-Rand Jackhamers, I-in. and 1 1/4-in., with hollow drill steel, are used to undercut the quarry face with 10-ft. holes. The face is "blown" and allowed to slump on the quarry floor. Loaded by a Marion electric shovel into trucks, the shattered rock is taken to the primary crusher 2500 ft. away. In addition to the normal quarrying operations, a drift into the northeast wall of the middle quarry was begun about 1935, and has advanced about 2000 ft. since then. Rooms have been driven at angles to the drift along choice beds of slate. The drifts and rooms have a roof more than 35 ft. high and the main drift and rooms are all more than 40 ft. wide. There is no cribbing at any place in the mine. Several of the rooms were driven upward on a 5' slope and in some of them there was stop-ing. Ingersoll-Rand Jackhamers are used, and only wet drilling is practiced. When visited in January 1940, an electric shovel was operating at the head of the drift, scooping up the slate blasted out of the working face. This, too, is trucked to the primary crusher. Some of the better quality slate is saved for making slate shingles. The primary crusher, which is a No. 30 McCulley gyratory, receives the slate from the trucks and crushes it to about a-in. size (Fig. I). This product travels by a 30-in. belt conveyor to Niagara vibrating screens with 2-in. holes. The minus a-in. product moves to a storage silo by bucket

Jan 1, 1948