Search Documents

By F. A. Forward, A. H. Ross, J. Halpern

IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to +15oC. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO3 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi O2. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1958

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By John P. Bryant, Samuel Kincheloe

Plant nutrients are obtained by plants from both the air and the soil. Carbon dioxide, a gaseous form of carbon and oxygen, supplies the carbon which usually makes up 50% or more of plant structure. Plants are capable of absorbing carbon dioxide directly from the air. Most of this nutrient comes from the air, although some carbon dioxide is absorbed by soil water and taken into the plant as liquid. Growing plants use more water than any other substance. Plant nutrients in the soil dissolve in soil water; soil water entering the plant carries nutrients into the plant structure. Water is then given off into the air as the plant breathes or transpires. Inorganic or mineral nutrients essential to plants are supplied through the soil. Inorganic or mineral composition of plants usually is less than 5% of their weight. In most crop-growing areas, much of this nutrition is inadequately supplied from the soil and must be provided by fertilizers. Proper fertilization of a soil to improve its mineral level and productivity is the role of the fertilizer industry. The 13 essential plant nutrients which often must be added to soils or plants and are generally considered fertilizer minerals are categorized as primary minerals (nitrogen, phosphorus, and potassium); secondary minerals (calcium, magnesium, and sulfur); and micronutrients, or trace minerals (boron, iron, manganese, copper, zinc, molybdenum, and chlorine). These classifications are based on quantity of nutrients utilized by plants and have no implication as to function or degree of necessity. One point of major significance to the fertilizer industry is that not all nutrient carriers supply that nutrient in a chemical form which will be available to the plant. Thus, a product which may be considered a fertilizer mineral may require substantial processing or may require substantial processing or treatment before it becomes useful as a nutrient carrier. Fertilizer Industry Scope Until about 1900 demands for higher crop yields were met simply by bringing new agricultural lands into cultivation. Since that time great progress has been made in increasing yields through fertilization and improved varieties and cultural practices. The importance of the fertilizer industry to the economy and welfare of the US is widely recognized. Fig. 1 illustrates the relationship of lime and fertilizers to crop yields. In terms of tons of fertilizer products, the growth of the industry has been phenomenal, particularly between 1950 and 1980. Table 1 shows the increase in fertilizer usage. Primary Plant Nutrients in Fertilizers Primary minerals (nitrogen, phosphorus, and potassium) are designated as such because [ ]

Jan 1, 1983

By J. G. Thompson

OXYGEN, nitrogen and hydrogen are present in practically all metals in one or more of the following forms: (1) molecular gas in blowholes or blisters, (2) combined in nonmetallic inclusions such as nitrides, oxides or silicates, and (3) in solid solution in the metal. Gaseous elements, in some of these forms, are encountered in practically all metals and alloys but possibly have received most publicity in connection with iron and steel. In fact, the entire steel industry depends upon the control of the oxygen content during the refining process, as well as in the finished material, and it was only after the adoption of the use of efficient deoxidizers such as manganese that the production of good steel with a low carbon content became possible. In normally clean, sound steel the amount of hydrogen is negligible and the amounts of oxygen and nitrogen vary from a few thousandths to a few hundredths per cent. However, many of the effects attributed(27,31,40.41,53,54,55,56,62) ? to the presence of these elements are important and at first glance appear to be out of proportion to the amounts of impurities involved. The presence of oxygen is believed to affect the solubility of carbon in austenite and ferrite and thereby to affect the structure of the iron or steel. Such properties as strength, hardness, ductility, elastic limit, impact resistance, magnetic permeability, tendency toward caustic embrittlement, irregularity in carburization, the cutting life of tools, certain corrosion phenomena, the presence of flakes, seams, bands, ghost lines and hair cracks, and the tendency to age-harden, all have been attributed to the presence of oxygen.

Jan 1, 1932

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation&apos;s bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation&apos;s bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

By Cecil Desch

THIS annual lecture, under the auspices of the Institute of Metals Division, and which was illus- trated by lantern slides, has been printed in full and a limited number are available for distribution on request. Some excerpts from the lecture are given below: Ever since the simple geometrical relations of crystals were discovered, it has been recognized that their proper-ties are best explained by assuming that their ultimate particles are arranged on a space lattice, and that the char-acteristics of that lattice determine the shape of the crystal and its physical and mechanical properties. Modern ex-amination by means of X-rays has widened that concep-tion and given it greater; definiteness, and the atoms are now regarded as the particles forming the space lattice. The splendid achievements of investigators in this field have made it possible to state, for a large number of sub-stances, the form and dimensions of the lattice. The char-acteristic of a lattice is that a unit of simple geometrical form is repeated at regular intervals in three dimensions so as to fill the entire crystal. It follows that there must be certain planes in which the atoms are more closely packed than in planes drawn at any angle to them, and it is these planes of closest packing which play the greatest part in determining the growth and other properties of the crystal. There are actually two stages in crystallization, what-ever be the medium in which it occurs. The first is the ap-pearance of crystal nuclei; the second the growth of those nuclei to form crystals of appreciable .size. The first is clearly a kinetic phenomenon. In the molten mass, solu-tion, or vapor, the molecules are in a state of rapid motion and frequent collision. When the temperature has fallen so far. that it is possible for a crystal to exist, a few col-liding molecules may fail to rebound, and so become at-tached to one another, the balance between the attracting and repelling forces-between them causing them to arrange themselves on a space lattice, to which other molecules sub-sequently attach themselves. It was once maintained that the X-ray evidence demanded that the molecule should dis-appear in the solid crystal, but this was a wrong inference, and in many crystals, but not in all, the chemical molecule retains its identity in the solid state. In pure metals the atom and the molecule are identical, so that the conditions are unusually simple. How many. nuclei will be formed in a given mass is evi-dently a problem in probability. Experiments to deter-mine the relation between the temperature and the number of nuclei formed in a given time have been made with some success by using viscous organic substances, but metals offer much greater difficulties, and the few determinations which have been published are vitiated by serious errors. However, the examination of sections of ingots of the same composition and cast at &apos;the same temperature in similar molds will show, that the number of crystals does not vary widely.

Jan 3, 1927

By H. W. Miller, V. H. Wilhem

Although the year 1933 was a period of uncertainty, considerable new development was initiated, with a high percentage of favorable results, for owing to financial conditions only projects of merit were proposed and developed. Unfavorable marketing conditions caused severe financial losses to refinery and sales departments of nearly all companies during the first half of the year. In anticipation of stabilized Government control, earnings were generally favorable during the third quarter but failure of the Government to take legal action against violators of the proration orders, and lack of agreement on a definite plan of curtailment, resulted in considerable overproduction and demoralization of the market structure during most of the final quarter. However, toward the close of the year Government action against violators of the Oil Code had a tendency to decrease overproduction materially and give the market a firmer tone. As a whole, the price structure of crude oil was maintained at a high level during the year; in fact, at a much higher level than the price of refinery products warranted. At no time during the year was production within 10,000 bbl. daily of the state allotment, overproduction of crude reaching a peak of 70,000 bbl. on Sept. 7, average daily average for the year being about 27,000 barrels. Numerous plans for equitable curtailment were prepared and tested during the year, none of which fully solved the many and intricate problems faced by operators who were in most cases willing to curtail if they could feel that cooperation was being practiced by their neighbors. Outstanding events in California oildom during the period under discussion may be classified under the following headings: 1. New discoveries. (a) New development in proven areas. (b) Deeper zones in settled pools. 2. Unproductive wildcat operations. 3. Whipstocking practice and procedure. 4. Progress of unit and orderly plans of development.

Jan 1, 1934

* Kennecott Copper Corp. gets Charles R. Cox as president on Jan. 1. Mr. Cox is resigning his position as president of Carnegie-Illinois to take the new post with Kennecott, left vacant by the death of Mr. Stannard in September. •The ECA signed a contract in December to advance X3,600,000 to Newmont Mining Corp. to aid development of lead and zinc mines in French Morocco. The funds are to be repaid in lead and zinc for the United States&apos; stockpile over a period of seven years. The mines are owned by the Societe des Mines de Zellidja, with which organization Newmont is associated. • Under the direction of John M. Brooks, Jr., general manager, the Matahambra mine in Cuba, will probably produce sufficient tonnage to make 4 million lb of copper per month during 1950. The grade is presently running between 7 and 10 pet. •S. H. Ash reports that the fatality rate per million-man-hr for the anthracite industry for 1949, through November, is 0.78. This is 15 pct better than that achieved during 1948, which was the lowest fatal injury rate in coal mining history. The first full year on record without a major disaster was recorded in 1949 (p. 34). •The Atomic Energy Commission has authorized the production of 200 lb of uranium metal for use under AEC license in non-Commission research projects. •A national survey of projected 1950 purchases of new machine tools, machine tool accessories, materials handling equipment, etc., just completed by the American Society of Tool Engineers reveals that, of the companies reporting, 80 pct state that they plan to buy either more equipment or the same amount as in 1948. • Armour Research Foundation is conducting investigations for the use of clay and shale deposits to make lightweight aggregates. The material is heated until it expands and forms material suitable for mixing with cement which it is hoped will be lighter, stronger, have better insulating qualities and will lower the cost of concrete. •In the first six months of 1949 the bituminous coal miners&apos; average hourly earnings were $1.94 -as compared with X1.392_ national average for all manufacturing. Average annual earnings of full-time employees in the bituminous coal mines in 1948 were $3387 as compared with $2809 for all industry. •LaSalle Business Bulletin reports: "year ends on a rising trend in industry and trade ... nearly record-breaking demand from almost all sources keeps business high... most indicators but little below postwar peak... forces keeping activity high arestill powerful--changes in general business conditions likely to be slow and moderate." •Office of Internal Trade of the Commerce Department requests that technical data significant to the national security which is to be sent outside of the United States be submitted to it for an official opinion on the desirability of transmitting such information. This voluntary compliance program is part of our national security control. • Blast furnace slag reduced to 12 to 16 mesh is being used for sanding track at the Mont Coal mines of Armco. The slag replaces silica sand which caused silicosis. It has proved so effective and cheap that tests are being made to use the slag for rock dusting.

Jan 1, 1950

The function of a preposition is to show the relation of one thing to another; it is necessary therefore for the writer to select the preposition that indicates the particular relation, otherwise he will fail to express himself clearly. Is it against common sense &o suggest that a Government is justified, morally as well as constitutionally, in preventing the decay of an industry by insisting upon the amalgamation of the prosperous with the needy? All these seven prepositions are used correctly. With the first dredge introduced in Russia, of Werf Conrad, Haarlem, make, this method of alluvial mining became important. Here the prepositions "with", "in", and "of" are used wrongly. He means: "This method of alluvial mining sprang into importance shortly after the first dredge, made at the Werf Conrad, Haarlem, was introduced into Russia." The statement itself is not true, but for that I am not responsible. Once, while I was serving with him, we were frozen in out of sight of land in the Gulf of Pichili in the North of China. Admiral Fisher wrote thus. He has used nine prepositions in making this brief statement. The sequence of three prepositions "in out of" is particularly awkward. Lounsbury says : One might fairly infer from the way in which it [newspaper English] is often spoken of that with the steadily increasing circulation of this sort of periodical literature there is no hope whatever for our speech. "Of that with" is lamentable. The construction is thoroughly bad, and it is bad mainly because the misplaced prepositions have tangled the meaning. I suggest:

Jan 1, 1931

By W. H. Kantner

In this paper, no attempt will be made to theorize on subsidence. Only known data and actual facts will be given, with a few exceptions noted where other factors and outside influences tend to change subsidence directly resulting from porphyry caving. The area under observation is known as the Southeast Extension of the East orebody. The orebody is irregular in outline and dips to the south and the east, extending in depth from about 425 ft. below the surface to 1050 ft. below the surface. In the upper horizon, the orebody is about 400 ft. long and 150 ft. wide. At 720 ft. below the surface, the ore outline is approximately 450 by 170 ft.; 70 ft. below this, it is 500 by 110 ft., with an extension at the north end to the east 270 by 120 ft. From this elevation to about 900 ft. below the surface, the ore spreads out to the cast and south, being about 700 by 500 ft. between these vertical limits. Below this it pinches out and at 1060 ft. below the surface is only 100 by 100 ft. The nearest point of the orebody—which is on the northwest side—is 600 ft. &apos;southeast of the Sacramento shaft. The country rock is all porphyry. Fig. 1 is a vertical east-west section showing orebody and original surface. The surface over the orebody was fairly regular and in this area and adjacent to it were portions of the surface plant, roads, and the main plant railroad to the concentrator. Fig. 2 is a map of the surface over the porphyry area. Caving operations started in April, 1925, at the approximate top of the orebody. The first lift was on the 600-ft. level; the ore was extracted by means of the Morenci timbered slide method and was from 425 to 455 ft. below the surface over an area of about 22,000 sq. ft. This lift was finished in May, 1926. The second lift, on the 650-ft. level, was already in production by May, 1926, so extraction of ore was continuous. This lift was 48 ft. high and covered an area of about 30,000 sq. ft. The ore from this lift was extracted by means of a modified Morenci timbered slide method. This lift was finished in March, 1927. The direction

Jan 1, 1934

By K. C. Sclater, B. R. Stephenson

Recent progress in oil-recovery methods has brought into prominence gas-energy relations in oil sands. The greater the effort made to utilize this gas-energy relationship to the best advantage in oil recovery, the greater becomes the need for more precise information concerning physical conditions as they actually exist in an oil well. The intelligent use of gas-oil ratios when considering production efficiency has been the subject of much recent discussion. It has been stressed that the pressure as well as the volume of gas must be known when considering the efficiency of a producing well on an energy basis. When methods of production are compared on an energy basis it implies a knowledge of pressure, temperature and physical properties of the fluids at the bottom of the well. In questions concerning gas-lift and the pressure control of wells usually there is a wide variance of opinion among engineers when energy relations come up for discussion. Perhaps this difference f opinion can be traced to erroneous assumptions made with regard to the physical conditions existing within the well. If erroneous assumptions are made it follows that computations based on these assumptions will give results which also will be in error. That erroneous assumptions are made is not to be wondered at because when handling a fluid composed of gas and oil, we are dealing with a complexity of hydrocarbon components each varying to some degree in physical and chemical properties. This means that the physical state of the gas and oil will depend not only on temperature and pressure but that it will be influenced also by the relative amounts of the various hydrocarbon components present. If water is present the problem becomes still more complicated. From these considerations alone it would appear that we can well afford to give some thought to devising more positive methods or means for obtaining data on physical conditions within the well rather than depend entirely on computations from casinghead data. If these data

Jan 1, 1929

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friede1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to B00 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By J. W. Stewart

The aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I). It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the 15 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1943

By Ralph E. Grim

THE technology of clay minerals is defined, for the purpose of this review, as- the application of fundamental data regarding clay minerals, and techniques of handling them, to the various industries, arts, and professions concerned with clay materials. The aim of the paper is to narrate recent developments in clay mineral technology. This review does not claim to be complete, and perhaps gives undue emphasis to matters that have been worked on in the author&apos;s laboratory or with which he has some other connection. In the United States in recent years, particularly since the end of World War 11, interest in clay mineralogy has increased greatly. Many laboratories in many different fields have embarked on studies of clay minerals but unfortunately much of this work has not been published. CERAMICS In the field of ceramics, in recent years, a great deal of interest has developed in clay mineralogy. Papers too numerous to be reviewed here have been published portraying the clay mineral composition of substantially all the important types of ceramic clays in all countries. There has been a growing tendency to attempt to solve processing problems on the basis of clay mineral data rather than chemical analytical data. Likewise, there is an in- creasing tendency to control the characteristics of raw materials on the basis of clay mineral composition rather than chemical composition. In the United States in the last few years something like 50 differential thermal analyzers have been set up, and many are for the sole purpose of controlling raw material and processing. The ceramic industry is currently increasing its attention to the influence of exchangeable ions and soluble salts on physical properties. Ion concentration in clay suspensions has long been a matter of interest, but now it is also of interest in clays in the plastic state because of its recognized importance in the plastic, shrinkage, and bonding properties of clays. Students of clay have long recognized that an understanding of the plastic properties of clays is based on an understanding of the character of the water in clay-water systems, the nature of the binding force between individual clay mineral particles, and the factors that control the character of the water and the nature of the bonding force. In the last few years, some extremely important contributions have greatly increased the understanding of the nature of water adsorbed on the clay mineral surfaces. In this connection the work

Jan 1, 1952

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country&apos;s production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber&apos;s salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

By W. S. Burbank, B. S. Butler

STUDY of the ore deposits of Colorado has disclosed, in numerous places, sharp changes in both mineralogy and metal content of the primary or hypogene deposits with change in depth. A clear understanding of the meaning of these changes is requisite to form intelligent conclusions that can be applied in the exploration of such ore deposits. This paper is an attempt to set forth some of the geologic and chemical relations of minerals that bear on this problem. The effect of the differing electrode potentials of elements on the order of oxidation and on the order of displacement of one metal by another metal in supergene sulfide deposits has been studied for many years by several investigators. The results all agree rather closely with the original Shurmann series of replaceability of metal sulfides, as Wells has shown.1 So far as the writers are aware there has been little attempt from the geologist&apos;s viewpoint to correlate the electrode potentials of the elements, other than those of the common metals, with the positions and mode of combination of the elements as found in ore deposits, and in particular in hypogene deposits. Wells2 discusses electrochemical activity between solutions and certain ore minerals and mentions the possibility of its effect in precipitation reactions. The senior writer for a number of years has emphasized the importance of oxidation-reduction reactions as a factor in the formation of certain hypogene ore minerals, and as the electrode potentials are a measure of the relative Oxidizing and reducing power of the elements and their ions, it seems possible that a study of them may offer some suggestions on certain problems. The data at present available for such a line of

Jan 1, 1929

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By W. H. Emmons

THE exploration of deposits of the metals will never become an exact science. There will always be an element of uncertainty in prospecting and developing mines. In countries where the surface has been closely scrutinized, most of the deposits whose outcrops contain valuable metals have probably been discovered. Many metalliferous deposits, however, are normally so much altered at the surface that the true significance of their outcrops is likely to be obscured. If a deposit is not exposed, its presence may become known by some one of its characteristics that is different in kind or in degree from a similar feature of the associated rock. Thus, a deposit that is not exposed may be discovered because of its magnetic property. So few minerals are strongly magnetic that the value of magnetic surveys is limited, but the dip needle has nevertheless proved of great aid in locating magnetic belts, and these in some regions are associated with workable iron ores. The Cuyuna Iron Range of Minnesota, which does not exhibit any outcrop of iron ore, was discovered by drilling "areas of attraction" that are due to belts of magnetic rocks associated with the iron ores. In some regions the use of the clip needle is justified, even if it does no more than reveal the strike of the rocks, since a knowledge of the latter enables the driller to locate and point his holes to advantage. The measures of gravity by the use of the pendulum are so accurate, or the limit of error is so small, that one might detect the presence of a concealed tabular deposit approximately at the surface, 34 ft. (10.36 m.) thick, having a density double that of the surrounding rocks. However, not many deposits have a density twice that of ordinary rocks and a thickness as great as 34 ft.; if they lie a short distance below the surface the density or the thickness must be even greater. Consequently, there is not much hope of sufficiently developing the gravity method of detecting deposits of heavy ores to make it of practical value. If the limit of error could be reduced to about one-tenth the present factor, and if the rather tedious and painstaking methods of determining gravity that are now in use could be simplified, the method would promise some degree

Jan 3, 1917

By R. F. Mehl, W. Batz, C. Wells

Diffusion coefficient values for carbon in austenite covering a wide range of temperature and composition have been determined employing statistical methods. In addition, the relation between concentration and each of the following, D (diffusion coefficient), Q (activation heat of diffusion), and A (the constant in the diffusion equation), has been obtained. A study of the rates of diffusion of austenite was published in Metals Technology in 1940.&apos; The present investigation is an extension of the earlier work, undertaken (1) to obtain values of the coefficient of diffusion, D, over a much wider range of carbon concentration, and (2) to provide data in all ranges of concentration and temperature in such abundance that statistical methods could be employed to evaluate the accuracy of the data with unusual precision. Composition of Materials: Composition of materials used in this research program are listed in table I. These materials, all forged to about 1 1/4 in. rounds, consist of a high-purity iron, Armco iron, a large number of laboratory-made plain carbon steels containing amounts of impurities normally expected in high-quality commercial steels, and three silicon steels. Since it was known at the time these steels were being made that impurities in the amounts present were unlikely to affect carbon diffusion rates&apos; significantly, the effort made to obtain high-purity steels was not as persistent as it otherwise would have been. Procedure: In general, the procedure followed by Wells and Mehl and described&apos; in detail in an earlier publication&apos; is the one used by the present authors. However, certain modifications have been made which it is believed allow diffusion data to be interpreted more objectively and correctly. These are described completely under appropriate subheadings which follow. Experimental Procedure: Experimental procedure includes (1) the preparation of specimens by welding steels of different carbon contents, (2) the heating of these for certain times at selected temperatures in order to diffuse carbon along the specimens across the welded "interface," and (3) the determination of the carbon distribution across the diffusion zone. Preparation of Specimens: Prior to welding steel of one carbon content to iron or steel of another carbon content, surfaces to be welded are machined perpendicular to the longitudinal axis of cylinders which are about 3/4 in. in diam and 1 1/2 in. long. The prepared, flat, parallel surfaces are brought together and butt-welded electrically. Evidence of a good weld is given in fig. 1. Welding temperature

Jan 1, 1951