Search Documents

By H. I. Aaronson, C. Laird

Cold rolling by 50 pct a A1-4 pct Cu alloy containing many 0' plates has been found to accelerate markedly the transformation of 8' to 0 upon further aging. Although the basic mechanism of this transformation remains unchanged by plastic deformation, the nuclea-tion kinetics of 8 become appreciably more rapid and also less dependent upon temperature. Particularly at lower aging temperatures, rounded idiomorphs replace several faceted rnorphologfes. The rates of growth of 9 idiomorphs in deformed specimens aged at 300°C are appreciably more rapid than simple volume diffusion control allows. This observation is shown to be explained by an excess vacancy, rather than by a dislocation Piping mechanism of growth. ThE rather complex phenomenology of the 8' —8 transformation in Al-Cu alloys has been recently elucidated in considerable detail by means of transmission electron microscopy.'-4 This technique was also employed in the present investigation in order to examine the effects of plastic deformation upon the transformation of 8' to 8. The mechanism of the transformation in undeformed Al-Cu alloys has been established as the following sequence of events.1"4 The first step is the nucleation of 9 at (Y:8' boundaries. Nucleation of a 0 crystal takes place, however, at only a very small proportion of the 8' plates present. Each 0 crystal simultaneously consumes the host 8' plate and the a! in the immediate vicinity, with growth into a being the rate-controlling process. The remaining 8' plates are then dissolved as they fall under the concentration shadow of the growing 8 crystals. The evidence on the effects of plastic deformation upon these processes is intriguing, but much less detailed. The careful X-ray studies of Graf and Guinier have shown that the aging times required to form detectable amounts of 8' and 8 are reduced by prior cold working. Thomas and Nutting confirmed these results by replication electron microscopy. Nile-shwar,* on the other hand, reported that creep deformation decreases the rate of formation of 0. While this difference may have been caused by the use of concurrent rather than successive deformation and ag- ing, the X-ray technique which he used was able to monitor only the 0 phase. It is thus possible that the times needed to form 8' were increased moreg than the kinetics of 8' — 8 transformation were accelerated. At 90 pct deformation by cold rolling, Graf and Guinier found that the usual 0' —0 8 sequence is reversed: 0 forms first. von Heimendahl 10 confirmed this result with transmission electron microscopy. Pollard and Nutting, 11 and more recently Driver and Barrand, 9 having used the same technique, report that 9 also forms first during creep deformation. In the present study, the maximum amount of deformation was limited to 50 pct reduction by cold rolling in order to insure that 8 formed principally by the decomposition of . I) EXPERIMENTAL PROCEDURES This investigation was conducted on an Al- 3.93 pct Cu alloy, prepared as previously described. 4 Morphological and crystallographic effects of plastic deformation were studied in specimens annealed 6 hr at 548°C, quenched, and then aged for either 3 or 8 hr at 250°C to form large numbers of 0' plates. After cold rolling to a 50 pct reduction in thickness, the

Jan 1, 1969

By H. N. Thomson

GENERAL. THE Tooele plant of the International Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. FIG. 1.-TOOELE PLANT OF THE INTERNATIONAL SMELTING & REFINING Co. The copper plant has been in operation since July, 1910, and the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 7, 1913

By Joseph Fry, Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep bandstone in the Elk Basin Field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes. of gas in solution. saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep Reservoir of the Elk Basin Field has unusually varying physiral characteristics, such as a saturation pressure of 1,250 psia and 490 cu ft of gas in solultion in a barrel of oil at the crest of the structure and a saturation pressure of 530 psia and 134 cu ft of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the gas in solution in the oil varies from 18 per cent for oil on the crest to 5 per cent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of the oil in the structure. Many geologists and petroleum engineers have considered that all the oil in a petroleum reservoir has rather uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas; that such is not always so is borne out by the results of the study by the writers. INTRODUCTION The Rocky Mountain region is one in which may be found striking examples of the unusual in oil and gas accumulations, as is evident from the following: The high helium content (7.6 per cent) of the gas in the Ouray-Leadville limestone sequence in the Rattlesnake Field, New Mexico, and gases of similar helium content in other fields; 50" to 55' API gravity distillate in solution in carbon dioxide gas and recoverable through retrograde condensation, in the North McCallum Field, Colorado; the occurrence of gas, oil, or both in closely related structures contrary to the usual concepts of gravimetric segregation: the accumulation of gas and/or oil in structures closely related to other structures that apparently are more favorable but do not contain oil or gas accumulations; the high hydrogen sulfide content (as high as 42 per cent) of the gas associated with oil in some fields in the Big Horn Basin, Wyoming; and the wide range of fluid chararteristics found in the Elk Basin reservoir. Elk Basin, an interesting old oil field that has been producing oil from the Frontier formation since 1915, is situated in a highly eroded basin resulting from the erosion of the crest of an anticline and some of the underlying softer shales. The field came back into national prominence during 1943 when it became known that it was the largest single reserve of new oil discovered in the United States that year. The Tensleep sandstone was found to contain oil in November. 1942, when a well drilled to a depth of 4,538 ft (44 ft into the Tensleep sandstone) flowed oil at the rate of 2,500 B/D. By the end of 1949, 137 oil-producing wells and five dry holes had been drilled, and approximately 32 million bbl of oil had been produced. Approximately 6,000 acres may be considered productive of oil in the Tensleep Reservoir, and estimates of the oil that will be produced average 200 million bbl. The Tensleep Reservoir has further interest because it ha-greater closure than any oil field in the Rocky Mountain region; the closure of the Elk Basin anticline is variously estimated at 5.000 to 10,000 ft. of which the top 2.00 ft of the structure contained oil. SUBSURFACE OIL SAMPLING Fig. 1 is a structural map of the Elk Basin Tensleep Reservoir, on which the nine wells used in this study and the numbers correvponding to the well designations hereafter referred to are shown. Wells 1. 2, 3, 4, and 8 were tested and sampled during October and November. 1943. and Wells 5, 6. 7, and 9 during June and July, 1944. An electromagnetic type sampler developed by the Bureau of Mines and described by Grandone and Cook' was used in obtaining the subsurface oil samples. As the wells were tubed nearly to bottom, the sampler was run as far as possible in the tubing hut never below the top perforations. The following procedure was used in testing and sampling the wells: A well was shut in for at least three days, after

Jan 1, 1951

By Joseph Fry, Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep bandstone in the Elk Basin Field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes. of gas in solution. saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep Reservoir of the Elk Basin Field has unusually varying physiral characteristics, such as a saturation pressure of 1,250 psia and 490 cu ft of gas in solultion in a barrel of oil at the crest of the structure and a saturation pressure of 530 psia and 134 cu ft of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the gas in solution in the oil varies from 18 per cent for oil on the crest to 5 per cent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of the oil in the structure. Many geologists and petroleum engineers have considered that all the oil in a petroleum reservoir has rather uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas; that such is not always so is borne out by the results of the study by the writers. INTRODUCTION The Rocky Mountain region is one in which may be found striking examples of the unusual in oil and gas accumulations, as is evident from the following: The high helium content (7.6 per cent) of the gas in the Ouray-Leadville limestone sequence in the Rattlesnake Field, New Mexico, and gases of similar helium content in other fields; 50" to 55' API gravity distillate in solution in carbon dioxide gas and recoverable through retrograde condensation, in the North McCallum Field, Colorado; the occurrence of gas, oil, or both in closely related structures contrary to the usual concepts of gravimetric segregation: the accumulation of gas and/or oil in structures closely related to other structures that apparently are more favorable but do not contain oil or gas accumulations; the high hydrogen sulfide content (as high as 42 per cent) of the gas associated with oil in some fields in the Big Horn Basin, Wyoming; and the wide range of fluid chararteristics found in the Elk Basin reservoir. Elk Basin, an interesting old oil field that has been producing oil from the Frontier formation since 1915, is situated in a highly eroded basin resulting from the erosion of the crest of an anticline and some of the underlying softer shales. The field came back into national prominence during 1943 when it became known that it was the largest single reserve of new oil discovered in the United States that year. The Tensleep sandstone was found to contain oil in November. 1942, when a well drilled to a depth of 4,538 ft (44 ft into the Tensleep sandstone) flowed oil at the rate of 2,500 B/D. By the end of 1949, 137 oil-producing wells and five dry holes had been drilled, and approximately 32 million bbl of oil had been produced. Approximately 6,000 acres may be considered productive of oil in the Tensleep Reservoir, and estimates of the oil that will be produced average 200 million bbl. The Tensleep Reservoir has further interest because it ha-greater closure than any oil field in the Rocky Mountain region; the closure of the Elk Basin anticline is variously estimated at 5.000 to 10,000 ft. of which the top 2.00 ft of the structure contained oil. SUBSURFACE OIL SAMPLING Fig. 1 is a structural map of the Elk Basin Tensleep Reservoir, on which the nine wells used in this study and the numbers correvponding to the well designations hereafter referred to are shown. Wells 1. 2, 3, 4, and 8 were tested and sampled during October and November. 1943. and Wells 5, 6. 7, and 9 during June and July, 1944. An electromagnetic type sampler developed by the Bureau of Mines and described by Grandone and Cook' was used in obtaining the subsurface oil samples. As the wells were tubed nearly to bottom, the sampler was run as far as possible in the tubing hut never below the top perforations. The following procedure was used in testing and sampling the wells: A well was shut in for at least three days, after

Jan 1, 1951

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By D. F. Coolbaugh

Successful mine exploration requires sound planning and modern exploration techniques, but it also requires perseverance and the right timing. The La Caridad mineral area has been known for over 70 years, but as with many mines, it was not "discovered" until viewed under new economic conditions and exploration philosophies. Present exploration of the La Caridad area began in 1964 and was carried out under a joint Mexican Government-United Nations Project. Detailed exploration was begun by Asarco Mexicana S.A. in late 1968. The geology of the La Caridad deposits conforms, generally, to the "porphyry copper" deposits of Arizona. However, breccias and pegmatites play a very important part in the emplacement of mineralization.

Jan 1, 1972

By A. F. Henderson, C. F. Cornell, A. F. Dunyon, D. A. Dahlstrom

IN processing magnetic taconites several steps of crushing, grinding, classification, and magnetic separation are required to produce a 60' pct Fe concentrate. Usually the final concentrate is in a slurry form of 55 to 70 pct solids by weight and is further characterized by a particle size of 60+ pct —325 mesh. In taconite plants already completed or under construction the conventional method used to obtain pellets suitable for blast furnaces is to filter the concentrate slurry, ball the filter cake, and then harden the green pellets in a traveling grate or in a vertical shaft furnace. Large tonnages must be handled in minimum floor space, with reduced maintenance and lowest possible operating cost. Filtration must therefore achieve two objectives: I) high filtration rate—in terms of pounds of dry solids per hour per square foot of filtration area—at a low filtrate solids concentration, and 2) a filter cake moisture that will always permit efficient balling within the normal fluctuations of ' plant operating conditions. If moisture contents are too high, balling may be impossible or result in a mushy ball .without enough green strength for the firing operation. Development work has met these objectives. At low investment and operating costs, filtration rates of 250 to 600 dry lb per hr per ft2 have been attained for concentrates of 60' pct —325 mesh. By combining the disk-type continuous filter with proper agitation, the Agidisc filter produces a homogeneous filter cake, easily discharged from the disk sectors. This application provides the lowest initial cost per square foot of filtration area, minimizes floor space, reduces down time for changing filter media to a negligible factor, and simplifies process control and maintenance for the operator. It is now possible to predict very closely the taconite concentrate filtration rates for a wide variety of conditions—either by experience or with a few simple leaf tests. When balling and pelletizing operations began on a continuous basis, it became apparent that moisture content of the filter cake was a critical factor and must always be controlled by the filter operator below some maximum allowable value. Accordingly the Reserve Mining Co. and the Eimco Corp. joined in a study of the many variables affecting filter cake moisture content. The study was conducted at the Reserve Mining Co. taconite plant at Babbitt, Minn. To process plant tonnage the Babbitt plant utilizes a 6-ft diam Agidisc filter with six disks and an 8-ft diam drum filter with 10-ft face. However, most of the plant filter investigations were made on the Agidisc because of its superior performance. A considerable amount of small-scale test work was first carried out to study more closely the individual variables and ascertain their effect on filter cake moisture content. A general correlation method was then developed which allowed reasonable prediction of moisture content at any operating conditions. This step was made necessary by the fact that in full-scale filtering, operating variables usually interact to produce a combined rather than a singular effect. Studies were then made on the full-scale filters to prove the validity of the correlations developed, and past operating records were examined to ascertain whether or not significant variations could be traced to any single factor or to a combination of factors.

Jan 1, 1958

By W. G. Frailing, W. P. Sims

The Lakeview Pool of Kern County, California, was discovered in 1910 with the drilling of Lakeview No. 1 which blew out and produced an estimated 8,250,000 bbl of oil in 544 days of uncontrolled flow. The well has since been known as the Lakeview Gusher. Full exploitation of the pool did not take place until about 25 years later. A total of 112 producing wells were completed in the Lakeview sand through April 30, 1949. As of that date, about 30 per cent of the total wells drilled were still producing, with an average pool production rate of approximately 2000 bbl per day. The cumulative oil production was about 41 million bbl of oil, or 55.3 per cent of the tank oil originally in place. The pool is bordered on its down-structure side by a body of inactive edgewater and water production where present has been principally the result of coning. Since the depletion of the greater portion of the gas energy by the Lake-view Gusher, the pool has operated under gravity drive. Relatively high angle dips, good permeabilities and favorable fluid characteristics have made gravity drainage particularly effective. Since January, 1942, the oil recovery -has been relatively constant at about 53,000 bbl per ft drop in fluid level. Correlations between the volume of reservoir space drained and the cumulative oil produced indicate that an ultimate recovery of 63.3 per cent of the tank oil originally in place is attainable. INTRODUCTION The Lakeview Pool is an outstanding example of gravity drainage. It is one of many productive reservoirs of the Midway-Sunset Field, and is located in Kern County, approximately five miles southeast of Taft and two miles north of Maricopa, California. Its position rel- ative to surrounding pools and to the Thirty-Five anticline is shown on Fig. 1. The northern portion of the pool lies in sections 32 and 33, Township 32 South, Range 24 East, Mt. Diablo Base and Meridian, while the southern portion lies in sections 25, 26, 35 and 36, Township 12 North, Range 24 West, San Bernardino Base and Meridian. As no two sections bear the same number, they will hereafter be referred to by section number alone. The purpose of this paper is to review the performance of the Lakeview Pool in an effort to evaluate the effectiveness of gravity drive as a recovery mechanism. REGIONAL STRATIGRAPHY AND STRUCTURE The oustanding structural feature is this area is the Thirty-Five anticline, the axis of which plunges South 75" East through the center of Section 35. As shown on Fig. 2, the following zones are oil and gas bearing in the Thirty-Five anticline area: Pleistocene Basal Tulare Tar Sands Pliocene San Joaquin Mya Sands Top Oil or Scalez Zone Etchegoin Kinsey Sand Wilhelm Zone Gusher Sand Calitroleum Sand Miocene Reef Ridge Lakeview Sand Sub-Lakeview Miocene Sands Monarch Sands or fractured shale equivalent Maricopa Webster Sand or fractured shale equivalent Fractured Shale-Uvigerina Zone C Obispo Sand and fractured shale equivalent Pacific Shale Zone The productive interval of the Lakeview Pool is limited to Upper Miocene and Lower Pliocene deposition. In this general area, the most prevalent type of accumulation results from stratigraphic traps or permeability pinchouts. As is the case of the Lakeview Pool, strati-graphic traps resulting from angular unconformities are present. The structure within the Miocene does not parallel that of the Etchegoin (Pliocene), as the Miocene beds were folded, and in places faulted, and subjected to erosion prior to Pliocene deposition. The Lakeview horizon consists of truncated sands which occur on the northeast flank of the Thirty-Five anticline. The direction of strike is west and northwesterly through sections 25 and 36 and continues northwesterly through sections 26 and 33, to the approximate center of section 32. At this point the strike swings to the northeast and the horizon re-enters section 33. in the northwest corner. The change in strike in section 32 affords synclinal accumulation at that point. The Lake-view sand is truncated updip by the Etchegoin overlap. To the southeast, the sand shales out, while to the northwest, the productive interval appears to be limited by a combination of stratigraphic pinchout and permeability barrier. Structurally, the Lakeview reservoir presents three areas of interest, as shown on Fig. 3. Area I in section 32 is a region in which a productive Sub-Lakeview Miocene sand is present. It occurs from 10 feet to 30 feet below the base of the Lakeview sand and attains a maximum thickness of 25 feet in Well No. 21, section 32. The producing characteristics of the Sub-Lakeview Miocene sand differ radically from those of the Lakeview sand. Water production at high structural locations and abnormally high fluid levels indicate that there was no communication with the Lakeview sand. Wells in Area I penetrated this sand and produced it in conjunction with the Lakeview sand. In Area 11, the Lakeview sand is a

Jan 1, 1950

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By Alfred E. Hunt, Geo. H. Clapp

The great advantage to he gained by a careful inspection of all materials used in construction, in regard to safety and permanency, and to accuracy of workmanship, has been longer recognized in Great Britain and on the Continent than in America. This is probably owing to the way in which great enterprises have been " rushed" in the United States. Time and cheap first cost, in too many instances, have been considered of more importance than absolute safety and durability; the structures being afterwards strengthened if this was found necessary. This has been most noticeable in railroads built through " new " country, where the object in view has been to reach the terminal point and get to work. These " loose " methods are now being very largely done away with, and a large proportion of the structures lately built are not only carefully inspected during the process of

Jan 1, 1891

By R. F. Dickerson, D. A. Vaughan, A. F. Gerds

ALTHOUGH the metallurgy of uranium has been under intensive study since the early 1940's, no systematic effort has been made to identify the non-metallic inclusions in uranium. Uranium carbide (UC), which is probably the most common inclusion found in graphite-melted metal, has been tentatively identified by previous investigators, but the other nonmetallic inclusions have received little attention. Since metallography is a valuable tool in metallurgical studies, the metallographic identification of the nonmetallic inclusions in uranium is important. Such an investigation has been completed and the identification of slag-type inclusions and of uranium monocarbide, uranium hydride, uranium dioxide, uranium monoxide, and uranium mononitride is described. Metallographic Preporation It is often possible to prepare specimens for metal-lographic examination equally well by several methods. The specimens which were examined in this work were prepared by one of two acceptable methods. For the convenience of the reader, both methods will be discussed in detail and will be referred to simply as Method I or Method II in the subsequent sections. For both Methods I and 11, specimens for microscopic examination usually were mounted either in bakelite or in Paraplex room temperature mounting plastic. Method I—Specimens were ground in a spray of water on a revolving disk covered successively with 120-, 240-, and 600-grit silicon carbide papers. It was necessary to perform the final grinding operation carefully on worn 600-grit paper to keep the scratches as fine as possible. After washing and drying, the specimens were polished for 3 to 4 min on a slow speed wheel (250 rpm) covered with a medium nap cloth. Diamet Hyprez Blue diamond polishing paste, Grade 00, 0 to 2 µ, was used as abrasive with kerosene as lubricant on the wheel. Specimens were washed thoroughly in alcohol and final polished electrolytically in an electrolyte composed of 1 part stock solution (118 g CrO, dissolved in 100 cm3 H2O) with 4 parts of glacial acetic acid. A stainless steel cathode was used. At an open circuit potential of 40 v dc, a polishing time of 2 sec retained inclusions well with the bath at room temperature. If additional etching was required to sharpen the interface between the metal and the inclusions, an electrolyte composed of 1 part stock solution (100 g CrO3 and 100 cm8 H20) and 18 parts glacial acetic acid was used at room temperature. Best results were obtained by etching for from 10 to 15 sec at 20 v dc in the open circuit. Surfaces obtained by this method are suitable for microscopic examination. However, if desired, they may be etched further with other chemicals. Method 11—Rough grinding was done on a wet 180- or 240-grit continuous grinding belt. The specimen was then ground by hand successively on 240-, 400-, and 600-grit silicon carbide papers in a stream of water. Final polishing was accomplished on a 4 in. high speed wheel (3400 rpm) covered with Forstmann's cloth. Linde B levigated alumina, suspended in a 1 volume pet chromic acid solution, was the abrasive. Specimens usually were polished in 5 min or less by this technique. Often the inclusions present in the metal were identified in the mechanically polished condition. When etching was required to outline inclusions more sharply, one of the two following methods was used. In the first method, the specimen is etched lightly while electropolishing in the chromic-acetic acid solution described above (1 part of stock solution to 4 parts of acetic acid). The electrolyte was refrigerated in a dry ice-ethyl alcohol bath and specimens were etched at 60 v dc on the open circuit for 2 or 3 cycles of 3 to 4 sec each. The second technique utilizes electrolytical etching at about 10 v dc (open circuit) in a 10 pet citric acid solution at room temperature. X-Ray Diffraction Technique The major problem in the identification of inclusions in metals by X-ray diffraction techniques is the extraction of a sufficient amount of each type of inclusion to obtain an X-ray diffraction pattern. In the present study, X-ray diffraction patterns were obtained from individual inclusions of the order of 10 µ diam. The polished and etched samples shown in the micrographs were examined at a magnification of X54 or XI00 with a binocular microscope. This allowed sufficient working distance to extract the inclusions with a needle probe for powder X-ray diffraction analysis. Friable inclusions such as MgF2, CaF2, UO2, and UH3 could be freed from the metal by probing the as-polished and etched surface. The fine particles then were picked up on the end of a Vistanex-coated glass rod (0.002 in. diam) which was held in a brass adapter made to fit the powder X-ray diffraction camera. The end of the glass rod was centered in the path of the X-ray beam. In the case of the UC, UO, and UN inclusions which are smaller in size, more metallic in appearance, and less friable than the other inclusions, it was necessary to etch the inclusion in relief before extraction. UN inclusions etched sufficiently in relief in the electrolytic polishing solution described in Methods I and II by increasing the polishing time. UN inclusions were relief etched by extending the

Jan 1, 1957

By L. D. Jaffe, F. W. Cotter, E. Cordon

The hardenability of titanium-base alloys was studied by metallographic examination and hardness survey of Jominy specimens end-quenched from the B range. Analyses of the data led to the equation log J = -0.57 + 0.25 @ct Fe + pct Mn + pct Mo) + 0.19 @ct Cr) +0.16 @ct V) + 0.03 @ct Zr). Here J is the distance, in sixteenths of an inch, from the quenched end of a Jominy hardenability specimen in the position of peak hardness, for material quenched from the B range. This equation fitted the experimental data with a standard deviation of approximately 0.29. The effects of the elements Al, Sn, W, Cu, Ni, B, C, N, 0, and H, and of pain size, were not statistically significant or not practically significant. A check against hardenability measurements in the literature showed agreement within the stated standard deviation. The equation should be useful in estimating hardenability of new or modified titanium alloys. HARDENABILITY in a titanium-base alloy is the ability of the alloy to retain the B structure on quenching. An alloy with high hardenability will retain the /3 structure even when cooled relatively slowly from a temperature at which B or P plus a is stable. A low hardenability material will retain P only if quenched extremely rapidly from the range of p or 0-plus-a stability, or will not retain it at all, at room temperature. High hardenability is desirable in titanium alloys to be heat-treated to high-strength levels. Its value is by no means limited to large section sizes. With high hardenability, a material can be solution-treated and cooled at a variety of rates, either to give high strength directly or, more generally, to give a soft ductile condition from which high strength can be obtained by subsequent aging. With low hardenability, high strength can be obtained, if at all, only by very rapid quenching, and there will generally be little increase in hardness on subsequent aging; an alloy of this type is limited in its applicability. On the other hand, alloys of very low hardenability have some advantages in weldability; essentially, they are always in the annealed condition, after welding as well as before. For commercial alloys, hardenability data are usually available, in the form either of property data after cooling from the solution temperature at various rates, with or without subsequent aging, or of results of a standard hardenability test, such as that originally developed for steels by Jominy and Boegehold.' When modifications of an available alloy are considered, or preparation of new alloy compositions, it would be Very convenient to be able to estimate the hardenability of the new material without having to make and test it. A method of estimating hardenability of titanium alloys from their composition was suggested by one of the authors some time ago, on a preliminary basis, utilizing scattered data found in the literature.' It seemed worthwhile to carry out a systematic experimental study of the effect of composition upon hardenability. EXPERIMENTAL PROCEDURE Approximately fifty heats of various compositions, weighing 8 to 10 Ib apiece, were melted in a small inert-gas tungsten-arc furnace with water-cooled copper walls. The starting material was 110 Brine11 titanium sponge, with high-purity metals added for alloying. Each heat was bottom-poured under vacuum through a molybdenum burnout strip into a cold graphite mold, to form an ingot approximately 4-1/2 by 3-1/2 by 3 in.* From each ingot were cut *The material was melted and cast by Pitman-Dunn Laboratory, Frankford Arsenal, to whom the authors must express their thanks. two pieces 4-1/2 by 1-1/2 by 1-1/2 in. These were forged, at temperatures adjusted to the composition, into 1-1/4-in. rounds, from which standard 1-in.-diam hardenability specimens3 were machined. A number of small samples were also prepared from forged materials of each heat, annealed, quenched from various temperatures, and examined metallographically. The P-transus temperature was determined by observation of the degree of resolution of primary a in these pieces. samples for chemical analyses were also taken from the forgings. One hardenability specimen of each heat was solution-treated for 1 hr approximately 50°F above the measured transus temperature, and the other for 1 hr approximately 250°F above the transus. (An additional hour was allowed for the specimens to reach furnace temperature.) These are not necessarily the temperatures that would be selected for

Jan 1, 1964

By A. E. Powers, J. F. Libsch

THE simultaneous influence of time and temperature upon the tempering process in steel is well known. Hollomon and Jaffe¹ have expressed the effect of time and temperature upon the progress of tempering by a single parameter, T (c + log t); where T is the absolute temperature; t, the tempering time; and c, a constant characteristic of the steel and treatment. It was found that when hardness data for plain carbon and low alloy steels were plotted vs. this parameter, a master tempering curve was obtained which satisfied all the data for a given steel and a given hardening treatment. Roberts, Grobe, and Moersch² successfully applied the tempering parameter to various tool steels, including high speed steel for tempering times ranging from 6 min to 100 hr. The influence of tempering time and temperature upon the physical properties of high speed steel has also been extensively investigated.'" Recently, the use of induction heating for very rapid tempering treatments has received attention. The authors% have shown that tempering treatments of only a few seconds duration may be successfully applied to plain carbon and low alloy steel. However, the influence of such short tempering treatments in high speed steel has not been explored. Since high speed steel is a highly alloyed steel exhibiting physical reactions during tempering that are often relatively slow and large in magnitude, it is an interesting steel for the study of tempering reactions. It was the purpose of the present investigation, therefore, to study the early progress of reactions leading to secondary hardness in high speed steel, type 6-5-4-2, and to determine if induction-tempering treatments of a few seconds duration are able to produce results equal to those of more conventional long-time tempering cycles. Experimental Details The chemical compositions for two different heats of W-Mo high speed steel used in this study are given in Table I. Table II summarizes the heat treatment given various groups of specimens cut 21/2 in. long and centerless ground to ¼ in. diam. Hardening treatments consisted of preheating to 1600°F (870°C) for V2 hr and then oil quenching from 2250°F (1230°C). Heat I was subjected to the high temperature in a salt bath for 3 min, while specimens of heat II were austenitized in a carbon-block muffle furnace for 10 min. Specimens of series E were immediately refrigerated to — 318°F (— 195°C) in liquid nitrogen following the hardening treatment to transform the major portion of the retained aus-tenite. Specimens of series F and G were subzero cooled to — 100°F (-75°C) in a dry ice-alcohol mixture. Induction tempering was performed with a Lepel high frequency converter operating at a frequency of approximately 300,000 cycles per sec. Heating cycles were controlled and recorded for each specimen using a chromel-alumel thermocouple, percussion welded to the surface of the specimen, and a modified high speed instrument with a timer previously used and described.' Temperature oscillation of the specimens, while being held at the tempering temperature, was ± 15°F (8°C). Tempering Treatments: After hardening, specimens were tempered between 900" and 1500°F (480" and 815°C) to study the progress of retained austenite decomposition and secondary hardening. The specimens tempered in salt for 1 hr (series C, G, and I) were considered to represent conventional treatment and are used for comparison with rapid tempering treatments. Several induction-tempering cycles were employed: 1—flash tempering, i.e., induction heating to the tempering temperature and immediately cooling (series A, E, and F); 2—induction heating for 60 sec at temperature (series B); and 3—double-induction tempering by two successive heating and cooling cycles (series D). All specimens tempered by induction were heated at an initial rate of 450°F (250°C) per sec except those of series E, which were heated at an initial rate of 1300 °F

Jan 1, 1952

By D. L. Garthwaite, F. M. Stewart, F. K. Krebill

Pressure has been maintained in the Elk Basin Ten-deep reservoir since the initiation of inert gas injection in Sept., 1949. Oil is being produced under conditions favorable for gravity drainage, including high angle of dip, appreciable structural closure, and fairly good per~neability. Results being obtained are high per cent recovery of oil-in-place, sustained field productivity, reduced operating problems, and recovery of plant products. The high recovery has been calculated by alpplication of the gravity drainage theory described in an earlier AIME paper.' It is also confirmed from field performance by comparing nil recovery to date with gas cap spuce voided. GENERAL INFORMATION The Elk Basin field lies in Park County, Wyo., and Carbon County, Mont., approximately 50 miles east of Yellowstone Park. Located at the northern end of the Big Horn Basin. the field is situated on an elongated asymmetrical anticline (Fig. 1). The pressure maintenance project covered by this paper involves the Embar-Tensleep reservoir in this multi-pay field. Discovered in Nov., 1942, it has a proved productive area of over 6,300 acres. It consists of the 210-ft thick Tensleep sandstone of Pennsylvanian Age overlain by 40 ft of Embar dolomite of Permian Age. The two formations apparently are in communication with each other and are produced as a common source of supply. As 98 per cent of the reserves are contained in the Tensleep sandFtone, in this paper the Embar-Tensleep reservoir will he called simply the Tensleep. The reservoir is found at an average depth of 4,900 it, is approximately 7 miles long and 2 miles wide, and has a maximum oil productive closure of 2,330 ft. The strata dip an average of 21" on the west flank and 45" on the east. There are presently 132 Tensleep wells in the field drilled on 40-acre spacing; of these, 17 are shut in because of high gas-oil ratio (GOR) and eight are gas injection wells. Rock characteristics and related information for the pay section follow: Porosity, avg 10.7 per cent Permeability (air) from cores, avg 118 mds Permeability from PI'S 91 mds Connate water, avg 8 per cent Initial pressure (-400 ft) 2,234 psia Pressure April 1954 (-400 ft) 1.327 psia At high structural positions much of the better sandstone has connate water content of only 2 to 5 per cent as indicated by the coring of wells with oil in nearby Tensleep fields. In special imbibition tests, samples readily imbibed oil but repelled water. In tests on crushed samples, the sand grains rapidly settled in oil and carbon tetrachloride but formed a stable unsinking floc in water. This information indicates that the Tensleep sand is preferentially oil wet. The oil produced averages 29' API gravity and has a high sulfur content. Extensive sampling and testing have established the fact that characteristics of reservoir oil in this field vary greatly with structure, see Fig. 2. Additional detail on the variation of oil characteristics with structure at Elk Basin may be found in Reference 2. At original reservoir pressure the oil was undersatu-rated with gas, the bubble point being 1,250 psi at the crest but only 500 psi at the lowest elevation sampled. As noted on Fig. 2, other fluid properties—reservoir volume factor. solution ratio, gravity, viscosity, and hydrogen sulfide content—likewise vary greatly. These variations complicate mathematical analysis, for it is necessary to average these characteristics in order to enter them into reservoir engineering expressions. To further complicate analysis, sand-face pressure also varies greatly because of the increase in fluid head down structure. As an approximation, average properties under initial conditions may be read from Fig. 2 at the -450-ft elevation.

Jan 1, 1956

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958

By J. C. Purcupile, R. L. Morris

Present methods of roof support require that first a hole must be drilled, and then a toggle belt or grouted resin bolt be set. Automating this system is very difficult. Therefore, we decided to develop a system which would insert pins into the roof in one step. We think that this type of system can be automated much easier. It would then speed up the roof bolting operation and eliminate the need for a man to work under unsupported roof, making roof bolting a much safer job. There are two ways that a pin can be inserted in a mine roof without drilling a hole. It can either be pushed in, using a very high, constant axial force; or it can be hammered in like a nail. The former method involves very high compressive stresses in the pin, and requires complicated machinery to prevent buckling. Since hammering the pin does not require high axial forces buckling is not as likely. Also, experiments have shown that there are no problems associated with getting the pin to go in straight. We chose to develop the second method. While investigating methods for hammering a pin into a mine roof, we learned that piles were being driven 10 times faster than by conventional methods with a method called "orboresonance." We decided to turn the pile driver upside down, and drive pins up into the mine roof. Sonic Pin Setting Machine The machine consists of a steel bar supported at the nodal points of its first mode of transverse vibration (Fig. 1). A mechanical oscillator, driven by a hydraulic motor, is attached to one end of the bar. This provides the forcing function for the vibrations in the bar. The hydraulic power is supplied by a portable unit. When the forcing function is near the natural frequency of the bar, large amplitudes of vibration occur and require little power input. An anvil is attached to the bar at a point of maximum deflection, providing a means for striking the pin. Since the bar is being driven near its natural frequency, it takes little energy to accelerate the bar back and forth between each hit. This means that most of the power being put into the bar is going into driving the pin. This is unlike conventional pile drivers which use most of their power to accelerate the hammer back and forth between hits. The resonant frequency of the bar we used is about 250 Hz, which is in the audible range, hence the term "sonic pin setting machine." The system benefits are: (1) elimination of the two-step drilling and pin-setting roof bolt operation, (2) increased speed, (3) more intimate contact between the formation and bolts, (4) less expensive roof bolts, (5) higher integrity, (6) potential for automatic operation. Modifications During the months from Oct. to Dec. 12, 1974, under U.S. Bureau of Mines grant No. 00144104, "Projects on Coal Extraction," six members of the senior class at Carnegie Mellon University designed and built the experimental machine. They drove three pins into the Safety Research coal mine at Bruceton, Pa., and determined that the project was worth continuing. In January 1975 we began making modifications and repairs in preparation for a more extensive program of testing at Bruceton. The major items were: 1) Design and build a collapsible pin guide to keep the pin parallel with the line of travel of the lift table. 2) Move the anvil to the center of the bar. 3) Refinish the nodal holes and install new node pins and bushings. 4) Realign the bar in its frame. 5) Install a relief valve on the lift unit to control the upward force. The upward force that we exert on the pin is relatively small, so there is no tendency for it to buckle. This means that all we need to do is hold the pin straight during its initial penetration. This allows the bushing to travel up and down in a straight line. At the beginning of penetration, the bushing

Jan 1, 1977

By Strathmore R. B. Cooke, Eugene L. Talbot

THE perfluoro acids and derivatives show unusual surface-active properties that qualify them as possible flotation reagents. They lower the surface tension of water from 15 to 20 dynes below that obtainable with the corresponding hydrocarbon compounds.1, 2 Fluorochemicals adsorb very strongly on solid surfaces to give films that exhibit larger contact angles than films of the corresponding hydrocarbons."' * The large contact angles probably result from the terminal —CF3 group. The perfluoro acids are made by electrolysis of the corresponding carboxylic acid in anhydrous hydrogen fluoride.5 From the perfluoro acids many derivatives may be obtained, such as amides, amines, alcohols, xanthates, ethers and esters and others. Since the fluorinated analogues of the conventional hydrocarbon flotation collectors possess enhanced surface properties, a few were selected for testing. Because a survey of all possible minerals and reagent combinations would be out of the question, hematite was chosen to represent a nonsulphide system and pyrite to represent a sulphide system. The fluorinated reagents used in these experiments were prepared in the research laboratories of Minnesota Mining & Mfg. Co. Some were synthesized especially for this research. They are not available cokmercially. Separation of Nonsulphide Ores: The separation of oxides from silica has always been a challenge to the flotation industry because differences in surface properties of the minerals are normally insufficient to produce clean concentrates. Oleic acid," rosin acids,' and amine salts% ave been used to considerable extent to effect separation of metal oxides and silica. The system hematite-silica was chosen to represent the nonsulphides both because of its difficulty of separation and because large tonnages of easily obtainable material are available, such as gravity concentration tailings and nonmagnetic taconites on the Mesabi Range. The wash-ore tailings used here contained approximately 35 pct iron after desliming. Samples of the material used in this work were part of the same lot used by Chang, Cooke, and Huch9 and were prepared in an identical manner. Reagents for Nonsulphide Ores: Since one of the purposes of this investigation was to compare hydrocarbons with fluorocarbons, reagents of known behavior such as oleic acid, and the alkali metal salts of certain resin acids (Dresinates), were established as standards. Hydrocarbons and fluorocarbons of comparable chain length and other experimental fluorocarbons were tried as collectors for hematite. A list of the materials used and the concentrations of their stock solutions are given in Table I. Since silica can be selectively floated from hematite by conventional reagents," a few fluorocarbon reagents were also tried for this purpose. Their composition and concentrations are given in Table 11. Most of these reagents served the dual function of collector and frother. In the case of F-11 flotation did not occur but it served as a frother when F-6 was employed as a collector. Reagent grade sulphuric acid and sodium hydroxide were used to regulate the pH. Deionized water containing less than 0.1 ppm of salts expressed as NaCl was used for all solutions and flotation tests. The pneumatic flotation cell consisted of a 350-ml fritted glass Buechner funnel with a source of filtered air which could be controlled by a needle valve." A 50-g sample of ore and 250 ml of deionized water were added to the flotation cell and stirred slowly. The reagents were added and the pulp was conditioned before air was admitted to the cell. Approximately 15 ml of the pulp were removed for pH determination before flotation was started and were then returned to the system. The pH was again measured after flotation. Air was admitted to the cell until no further flotation occurred or until the character of the float changed markedly. Both the float and the nonfloat products were filtered, dried, weighed. and assayed for iron. The cell was washed in hot water and rinsed with deionized water after each test. Occasionally the cell was cleaned with concentrated hydrochloric acid to remove iron oxide particles from the glass frit. Experimental Results: Above a pH of 8, sodium oleate was an effective collector for hematite. The emulsification of equal parts of heavy fuel oil (20"

Jan 1, 1956

By H. W. Reinhardt, J. W. Dally

A dynamic photoelastic analysis of stress waves interacting with a free surface is described. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb N,). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. The mechanics of rock breakage by means of explosives has received considerable treatment by many investigators including Duvall, Obert, Broberg, Rinehart, and Langefors1-11 over the past two decades. Indeed in more recent years several texts12-15 have been written on the topic, treating a wide variety of subjects which are logically related to the modern technique of rock blasting. In rock blasting the chemical energy of a concentrated explosive contained in a relatively small diameter borehole is utilized to fragment the rock. The explosive is transformed into a gas with enormous pressures which exceed 10-5 bars18 This high pressure shatters the rock in the area adjacent to the borehole and produces dilatational and distortional stress waves which propagate radially away from the borehole. The state of stress associated with these outgoing waves produces a system of cracks which extend for a few feet from the borehole. The breakage produced in this manner is limited as the dynamic stress in the pulse attenuates markedly with distance. In the absence of a free surface, the stress wave propagates away from the source without further fracture. With a free face of rock near the drill hole, another mode of breakage occurs which is due to scabbing failure of the layer of rock adjacent to the free face. These scabbing failures are produced by the reflection of the incident waves and the conversion of compressive stresses into tensile stresses sufficiently large to fracture the rock. The detailed nature of the interaction of the stress waves with the free surface is complex and difficult to treat analytically. However, dynamic photoelasticity offers an experimental approach which gives a fullfield visual display of propagating stress waves and the reflection process. Applications of static photoelasticity to solution of problems related to mining technology have become relatively common (see, for instance, Refs. 17 and 18) with a plastic model loaded to produce a state of stress representative of that occurring in the workings of a mine. The application of dynamic photoelasticity is ex tremely limited. Tandanand and Hartman19 have used a multiple spark camera to study fracture in glass and plastic plates impacted by a chisel-shaped tool. This paper describes a dynamic photoelastic analysis of stress waves interacting with a free surface. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb-N6). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. Experimental Procedure The model illustrated in [Fig. 1] was fabricated from a sheet of Columbia Resin CR-39 to represent a bench with a fixed bottom. Properties of the CR-39 pertaining to these dynamic experiments are listed in [Table 1]. Scribe lines on 1-in. centers are used to identify locations along the bench face. The bench height was 8 in., the burden was 3 in., and the overall dimensions of the sheet, 16 and 18 in., were large enough to eliminate reflections from nonessential boundaries during the period of observation of the dynamic event. To simulate a charge in a borehole, a groove 0.062 in. wide and 0.080 in. deep groove was cut into the sheet from one side. The lower end of the groove was 1 in. or 1/3 the burden distance below the bottom of the bench. The upper end of the groove was 3 in. or one times the burden distance below the upper level of the bench. The groove was packed with 60 mg of Pb No per in. of length, and ignited with a bridge wire detonator. Four different ignition procedures were used to examine the effects of detonation direction on the stress wave interaction with the free face of the bench. In Test 1 the line charge was ignited at the top and the line charge detonated downward. In Test 2 the line charge was ignited at the bottom and the charge burned upward. In Test 3 the charge was ignited in the center with the top half burning upward and the bottom half burning downward. Finally in Test 4 the line charge was ignited at both ends simultaneously. Sixteen high-speed photographs of the photoelastic fringe patterns representing the stress wave propagation were recorded for each of the tests. A Cranz-Schardin multiple spark gap camera 20,21 was operated at framing rates which were systematically varied from 110,000 to 250,000 frames per sec during each test.

Jan 1, 1972

By G. E. Kedzie

The ore-deposits of ail that portion of the San Juan country within the borders of Ouray County are either in the tertiary ernptives or, confined to a relatively narrow zone, in the sedimentary beds just beneath them. The ore-deposits in the igneous formation

Jan 1, 1888