Search Documents

By K. S. Liddell

The Kell Process has been developed for the extraction of platinum group metals (PGMs) and base metals from sulphide flotation concentrates. The process has been successfully tested on several different sulphide flotation concentrates, including those from the UG2 chromitite horizon and the Platreef mafic/ultramafic layer. It has been shown to provide high (>95 per cent) and selective extraction efficiencies for the key valuable metals, i.e. Pt, Pd, Rh, Au, Ni, Co, and Cu. The Kell Process consists of several commercially proven unit operations. S, Ni, Co, and Cu are first selectively removed by use of a pressure oxidation step during which the dissolution of PGMs is minimized. The residue from pressure oxidation is subjected to a thermal treatment to ensure efficient PGM recovery by subsequent chlorination. All the core steps are very similar to well-proven conventional unit operations in common use, as are the subsequent metal recovery steps to provide marketable end products. Typical metallurgical responses of flotation concentrates from UG2 and Platreef to the Kell Process are provided, and key outcomes of an energy comparison study with smelting are summarized in this paper. Kell presents a potentially substantial improvement in PGM concentrate processing technology, in terms of economics via much-reduced power costs, ease of processing, and various environmental benefits. It allows for the treatment of high-chromium low-grade 'dirty' concentrates, such as secondary concentrates from the platinum industry's 'mill-float-mill-float' (MF2) flotation circuits and concentrates from retreatment of tailings. It allows greater concentrate mass pulls, has higher tolerance to gangue intergrowths in concentrates, and its use can provide substantial increases in overall PGM recovery. Its adoption would be a step change in the platinum industry, and given the commercially proven unit operations embodied in the Kell Process, at much-reduced risk compared with other more experimental technologies. Since the initial process development work, significant improvements and refinements have been introduced as a result of further compre¬hensive testing and process modelling. Pilot-scale testing and engineering study work is in progress for several selected sites.

Jan 1, 2012

By A. Baldwin

Reports technical progress in designing four machines to be used in mining coal underground, applying innovative concepts at the design stage (instead of add-ons). A study phase was followed by design activity, including calculations supporting the designs. Scale models of three machines were built, and a full-scale mock-up of the conventional loader was used to measure human factors parameters.

Jan 1, 1976

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By Walter Renton, Ingalls

SEVERAL years ago I became interested in computing the historic lead production of the United States, and the mines, or mining districts whence derived. This led me subsequently to an examination of the recent records- of some of the American zinc-mining districts and of the great lead and zinc-mining districts in foreign countries. My present article thus will be to a large extent an addendum to my book, "World Survey of the Zinc Industry," which was published by the Mining and Metallurgical Society of America in 1931, and to which I shall refer hereinafter as Ingalls, op. cit. Throughout this article all expressions of tons mean the ton of 2000 lb. Where original data have been given in metric tons I have converted in many instances simply by multiplying by 1.1, and long tons by 1.12. I have not been fussy about digits and have rounded off many figures. These may explain differences between data herein and other data.

Jan 1, 1946

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By Jeffrey S. Newman

This report presents a summary of the results of a four-phase program conducted for the Bureau of Mines to evaluate underground mine fire detection systems. In addition, Phase IV is presented in detail. The major accomplishments of this program are: 1) quantification and prediction of the distribution of fire products in a mine pas¬sageway; 2) quantification of "equivalent protection" by fire detectors as contained in Title 30 of the Code of Federal Regulations; 3) definition of detection criteria; 4) design of a detector test program for determining detector spacing requirements; 5) design, construction, operation, and calibration of a fire test apparatus for evaluating mine fire detectors; 6) quantification of several mine fire sources; 7) evaluation of several fire detector types including heat, CO and CO2 gas, and ionization smoke detectors; 8) development of generalized spacing criteria for mine fire detectors; and 9) development of performance specifications. Reports for Phases I through III are included in Appendices.

Jan 1, 1984

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0·03-0·04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0' 03-0' 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By Eleanor Abshire

This bibliography is the result of a cooperative project undertaken by the Bureau of Ships and the Bureau of Mines to accumulate literature published to date on zirconium and hafnium and to establish an information center on these metals for the use of any interested research organization or library. This bibliography, which will be supplemented as additional information is accumulated, consists of references, with abstracts, to pertinent literature on the subject published from 1907 to date.

Jan 1, 1957

By A. Drouin, D. Lemieux, C. Chouinard

"A gold bearing pyrite concentrate was treated at the demonstration scale (15 t/d) for the extraction of gold using a cyanide-free process. The pyrite was depressed in the flotation circuit in order to promote the flotation of copper and to achieve a sufficient copper grade to meet the copper smelter criteria. However, the recoveries of copper were 80% and only about 50% for the gold was found in the copper concentrate. The balance of the gold (50%) and copper (20%) contained in the pyrite concentrate as a reject from an overall flotation circuit. The gold grade in the pyrite concentrate is 5.40 g Au/t and copper about 0.77%. About 170 tons of pyrite concentrate were processed in the DST demonstration plant. The concentrate was first oxidized using a fluid bed to produce a calcine. Copper was then extracted as copper sulphate using diluted sulphuric acid. The residual solid was submitted to the DST chlorination process for gold extraction. Thereafter, the gold was recovered from the pregnant brine by precipitation over silica using DST proprietary process. The maximum gold recovery by chlorination was 90%. The average gold recovery by cyanidation of these calcines was 71%.IntroductionDundee Sustainable Technologies (“DST”) has developed a chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from ores or concentrates. The technology offers viable and efficient gold recoveries and the ability to handle refractory ores and contaminated material (As, Hg, etc..). The process was successfully demonstrated on hundreds of samples provided by various mines, exploration and development projects and has evolved from laboratory experiment to demonstration at an industrial scale.DST’s chlorination process operates in a closed loop circuit, which implies that no liquid effluents are generated. The chemistry and process design allows precious metal deposits containing base metals to be treated viably. The tailings from the process are inert and non-toxic, sulphide depleted and thus non-acid generating. The efficiency of the process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. The company completed in 2015 the construction of the first industrial demonstration plant operating with the DST technology. The plant has a capacity of 15 tons per day of mineral concentrate, and the ability to extract gold and silver utilizing DST chlorination technology.DST has tested its chlorination technology at demonstration scale on the refractory pyrite concentrate containing 5.40 g Au/t and 0.8 %copper. This auriferous pyrite concentrate, was by-product of copper concentrate respecting the copper smelter norms, is produced in a country where cyanide is prohibited and refractory to cyanidation. The pyrite concentrate was initially processed successfully (gold recoveries: > 90%) by the DST technology at laboratory (2011: 20 kg) and pilot (2014: 5 tons) scales to extract gold. About 170 tons of this pyrite concentrate were processed in the DST demonstration plant located in Thetford Mines."

Jan 1, 2017

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989

By John G. Henning

The Porcupine Joint Venture operates the Dome Mine in South Porcupine, Ontario. Dome underground began production in 1910. It is the longest continuous operating gold mine in Canada, producing in excess of 15 M ounces. More than 900 underground stopes have been mined and hundreds of miles of drifts, sublevels and raises developed. Underground mining methods included shrinkage, cut and fill and longhole. Not all stopes were backfilled upon completion, particularly the longhole stopes. The Dome open pit was designed above the underground mine workings such that, as the pit is excavated, it intersects underground drifts and stopes. Potential operational problems associated with the interactions between the stopes and the pit walls may occur, necessitating pit wall redesign, ground support installation and operational rescheduling. Each intersection of the pit with the underground mine workings is closely evaluated to maintain a safe working environment and wall stability. This paper discussed how risks to pit wall stability are assessed, mitigated and monitored.

May 1, 2004

By Gregory A. Stephan

A case history of design, prediction, probe pile driving, and construction of a pile foundation for Building 3 of Waterside at Bay Beach Condominiums located in Fort Myers Beach, southwest Florida, is presented. Site geometry constraints, the presence of a 12.0 ft (3.6 m) deep lake occupying the southern one-third portion of the proposed building footprint, and marginal subsoils provided specific challenges for design and construction of the foundation. The subsoil conditions were explored by performing Standard Penetration Test (SPT) borings and a Piezocone Penetration Test (PCPT) Sounding to depths of 100 ft (30.5 m) within the building footprint. Additionally, borings were performed to envelope the building. Deep foundation alternatives included driven concrete, monotube, and steel pipe pile as well as drilled shaft. Following an evaluation of high structural loads, site-specific constraints, foundation test data from buildings 1 and 2, and preference expressed by the project owner, a pre-cast prestressed concrete (PPC) pile-supported foundation system was selected as an economical and effective foundation approach. Use of an augered cast-in-place (ACIP) pile foundation system was precluded by the project structural engineer. This paper deals with the design aspects and methodologies utilized in choosing and economizing the foundation system. The building foundation was designed for an allowable pile capacity of 40 tons (353 kN) in compression, 1.5 tons (12 kN) in lateral capacity for a deflection of 0.25-in (0.64 cm) and 15 tons (133 kN) in uplift capacity. For the single story extended garage structure, a pile capacity of 27 tons (238 kN) was indicated in compression. As part of the design process, an extensive probe pile driving program was carried out in order to evaluate the pile driving equipment, determine and verify pile capacities, and optimize the production pile lengths. A total of 33, 14-in (356 mm) square, PPC concrete piles were driven within the entire building limits, and dynamically load tested utilizing Pile Driving Analyzer (PDA) as part of the probe pile driving program. Utilization of PDA during probe pile driving helped in predicting pile set-up (i.e., increase in pile resistance with time) as well as reducing the pile lengths by as much as 20 percent. It resulted in variable pile lengths during the production phase. This information was effectively utilized as part of the overall quality control program to install a total of 559 PPC piles (including 33 probe piles) within the Building 3 footprint, including the reclaimed lake area, to depths ranging from 45 to 58 ft (14 to 18 m) below existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared reasonably well with the capacities from the CAPWAP analyses for probe piles. This engineered, monitored and tested foundation solution provided a cost effective and satisfactory basis for completion and approval of the foundation work for the building resulted in cost savings over other foundation alternatives for the owner. The building has since been occupied and a recent reconnaissance has indicated that the building foundations are performing satisfactorily.

Jan 1, 2003

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By A Jäger, J L. Lett, J Rachocki and B Mobilio

The Newcrest Mining Limited Cadia East Panel Cave mines near Orange, New South Wales, Australia commenced production 1200 m below the surface in May 2014. Understanding the mine-wide impact caving had on excavation stability was a primary objective to ensure a safe working environment as production ramped up in the Panel Cave 1 operation and establishment activities were implemented in Panel Cave 2. The impact of cave interaction between Panel Cave 1 and Panel Cave 2 and establishing monitoring systems to assist mine planning and production as both caves joined is explained in this paper. Monitoring tools such as a microseismic system, open holes, HI-cells, extensometers, fibre optic sensing, cave markers, closure monitoring, underground observations and damage mapping were used to characterise the performance and position of the cave back. The data and observations collected were compared to predictions from numerical and empirical methods and used to calibrate the numerical models for forward prediction and to develop site empirical design tools. The results and methodology for monitoring deep high-output caves are the key discussion points in this paper.CITATION:Lett, J L, Jäger, A, Thornhill, T, Rachocki, J and Mobilio, B, 2016. Geotechnical challenges in cave monitoring – a modern approach, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 203–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Study on Mineral Processing of Refractory Copper-Nickel Ore

Sep 13, 2010

By C. H. Mathewson

MY treatment of the subject of "Metals of the Future" is imaginative rather than statistical or scientific, because reliable information concerning useful concentrations in the form of ore deposits of by far the majority of the elements does not exist and the chemical, physical, and mechanical properties of the unfamiliar metals are recorded only in fragmentary and uncertain form or not at all.

Jan 1, 1944