Search Documents

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

Up to the end of World War n, flat-back cut and fill stoping with or without square sets was the universal method of ore extraction. Rapid changes in practice occurred during the post-war years; first, ore extraction was fully mechanized; secondly, the stope design for new levels, notably No. 17 Level Zinc Corporation Ltd. and No. 19 Level New Broken Hill Consolidated Ltd., was modified to suit this mechanization; and thirdly, sub-level and shrinkage stopes were developed in orebodies where cut and fill methods would be uneconomical. The following is a brief survey of the changes that have occurred-most of which were inaugurated during the last five years.ROCK DRILLINGDuring 1951 open stoping was investigated in detail. In order to reduce steel handling problems, forged steel onepass detachable bits were introduced, but were soon superseded by the "Swedish method". Investigation showed that when using a bar and arm mounted 3-in. drifter the overall drilling time was approximately 6 min. per ft. compared with 4 min. per ft. using the light jackhammer-airleg combination with 1-in. hex. by 4-in. collared shank tungsten carbide-tipped steel.Although competitive with tipped steels on a cost per foot drilled basis (excluding miner's time), detachable steel bits proved most unsatisfactory for hard drilling conditions.Rapid blunting necessitated frequent bit changes and thus caused lost drilling time. This, together with rapid gauge...

Jan 1, 1957

By N. Kumar, A. K. Dhawan, A. Varughese, S. K. Khullar

Abstract The in-situ stress field is one of the primary parameters influencing the performance of underground structures particularly in the Himalayas where there is strong influence of topography and geology on in-situ stresses. It is always advisable to measure the in-situ stresses, in whatever best way possible. Hydrofracturing is one of the methods by which in-situ stress can be measured. This paper briefly describes details of the concept of Hydrofracturing in arriving at the in-situ stresses of the rock mass at Pancheswar Project. The data obtained from the tests has been analysed, interpreted and the results are presented in this paper. Kurzfassung Das Spannungsfeld an Ort und Stelle ist einer der wichtigsten Parameter, die das Verhalten der Untergrund-Struktur beeinflussen, insbesondere in den Himalayas, wo die Topografie und die Geologie einen grossen Einfluss auf die oertlichen Spannungen ausueben. Es empfiehlt sich stets die Spannungen an Ort und Stelle so gut wie moeglich zu erfassen. Die Hydrofraktur bzw hydrografisches Zerstueckeln ist eine der Methoden, die bei den Messungen der oertlichen Spannungen verwendet werden koennen. Diese Abhandlung beschreibt kurz Einzelheiten ueber das Konzept von Hydrofraktur bei der Bestimmung der Spannungen an Ort und Stelle von der Felsmasse bezueglich des Projekts Pancheshwar. Die gewonnenen Daten aus den Messungen wurden analysieret und ausgewertet. Die Ergebnisse werden dabei vorgelegt. Sommaire Le champ de contraintes in-situ est un des paramèters principaux influencant l’exécution des structures souterraines particulierèment en Himalaya où les forces in-situ sont fortement influencées par les caractéristiques topographiques et géologiques de la région. La fracturation hydraulique est une technique qui permet de mesurer des forces in-situ des massifs rocheux. Cet article décrit brièvement le mécanisme de fracturation hydraulique et présente les résultats de mesure des forces in-situ des roches au site du projet hydroélectrique de Pancheswar.

Jan 1, 2003

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

By Keet B. A, Waid J. S

The Gippsland Basin is one of Australia's most important producers of petroleum products. An inevitable byproduct of the production, refinement and transport of the millions of barrels of oil is thousands of tonnes of waste. These wastes are generated from the wellhead through to the petrol bowser and range from oily brines and coal tars to oil and petrol contaminated soils. The vast majority of these wastes are of a relatively low toxicity and most importantly are carbon-based and biodegradable. Current disposal practices tend to ignore the latter characteristic and inappropriate and/or expensive waste disposal solutions such as landfilling (tipping), incineration or ocean outfalls are the result. A very cost effective and environmentally friendly alternative is land treatment of such wastes. Landfarming, as it is called, has been successfully practiced in Europe for over a decade. Essential features of the system are: ò Application of a predetermined quantity of biodegradable waste in liquid, sludge or highly contaminated soil form, to pre-ploughed soil with concurrent addition of nutrients (N, P and trace elements) and lime to encourage bacterial activity. ò Harmless bacteria already present within the soil break down the carbon-based compounds into carbon dioxide, water and waste heat, WHILE concurrently generating new cells. The breakdown occurs over a period of weeks to months and continues with time with the extremely low levels of the more difficult waste types being the last to disappear. ò Further waste is applied to the soil at regular intervals. The treatment area may be dedicated to landfarming or may be used alternatively for agricultural purposes. Application rates vary but may be as high as 800 tonnes per hectare per year for wastes such as refinery sludges.

Jan 1, 1992

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

The 8 ft by 91/2 ft drive which joined No. 7 Shaft with Browne Shaft on the 1,480 ft level was extended from both ends and met at a point approximately 12,000 ft from No. 7 (2,000 ft from Browne).The surveying required for this 2 1/2 mile haulage drive called for greater accuracy than was obtainable from South Mine standard methods. Procedures and devices from published information were tried and modified as required to suit local conditions. Several new methods were applied and improved as the drive advanced. The control of angular, linear and level measurements was perhaps considerably in excess of the requirements, but this was offset by abnormally large discrepancies resulting from shaft plumbing. The accuracy of the final breakthrough, although not to the standard desired, was sufficient to complete the connection without inconvenience and added cost.INTRODUCTIONThe acquisition of the Browne Shaft leases in January 1962 presented the management of Broken Hill South Limited with the problem of transporting ore from these leases to its mill. It was eventually decided that diesel locomotivehaulage through a 2t mile drive on the 1,480 ft level between the two mines was the best solution. The drive was advanced from both ends after Browne Shaft was deepened by 80 ft to reach the 1,480 ft level horizon. Each end advancedabout 15 ft/day with the miners working three 7 hr shifts. Blasting was restricted to the end of the shift.The survey work involved five shaft plumbings and 78 theodolite stations in a traverse, underground and surface,of more than 5 miles. Because of the exceptional length of the drive, an unusually high degree of reliability was required.The aim was for a maximum error at breakthrough of 1 ft 1 in 30,000, and to secure this, precise methods of linear measurement were necessary. Shaft plumbing in particular posed special difficulties.

Jan 1, 1965

By K. P. Wang

Mining and metallurgy have had a long history in China, and resources there have always been considered promising. Under the People's Republic of China (PRC), a remarkable industrial renaissance is underway that should further gain momentum in the years ahead. Rapid development of minerals have not only brought the PRC prominence in industrialization, but also in world affairs. Chinese mineral developments, especially petroleum, have been increasingly in the news. Oil and gas may have great potential, but a very large coal industry is already in existence. The steel industry ranks fifth or sixth in the world. The PRC is also prominent in fertilizer, cement, and salt production. The export metals are well known. Also, the country is buying heavily in nonferrous base metals. The need to know and the intense interest in the subject have prompted this study. The world significance of Chinese minerals is pointed out. The history of growth and PRC's mineral supply position are reviewed. Evaluations are made of policy considerations and regional and technical factors affecting mineral development. PRC's mineral trade and efforts to obtain equipment, supplies, and know-how are assessed. Specific reviews are made of major mineral sectors, including coal and power, oil and gas, iron and steel, nonferrous metals, industrial minerals, and fertilizers and chemicals. The overall outlook is summarized.

Jan 1, 1975

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes' new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By S. Maurhofer

The Uetliberg Tunnel in Switzerland is the longest tunnel in Zurich?s new Western Bypass Expressway, connecting the Birmensdorf bypass in the west with the existing Zurich-Chur national motorway in the east. Thus the tunnel links the Zurich-West motorway interchange with the Zurich-South interchange (shown in Figure 1). The Uetliberg Tunnel project comprises two parallel tubes, each about 4.4 km long. The two tunnel tubes are connected every 300 m by a transverse walkway and every 900 m by a transverse roadway (Figure 2). The SOS niches are spaced 150 m apart. Portal stations with machinery rooms are located at the west and east portals. The tunnel falls with a gradient of 1.6% from the west portal at Wannenboden to the east portal at Gänziloo. The Project costs are about CHF 1.12 billion. The carcass construction started in March 2001. The Opening of the Uetliberg Tunnel is planed in spring 2009.

Safety is the No. 1 concern of any drill contractor or mine operator. Everyone in the industry knows a safe site helps stabilize operational costs and enables higher productivity. When it comes to exploration drilling, research has proven a majority of injuries are caused by the mishandling of coring rods. A driller helper will typically handle up to 50 rods per shift or up to 15,000 rods per year. With an annual 340 t (750,000 lb) in rods managed by hand, the risk of serious injury is extremely high. Because of this, the top request from the exploration industry is diamond rod handling. The Boart Longyear 4200 surface exploration drill, slated for release in 2009, will give the industry a hand-free, operationally safe rig.. Developed through the collaboration of its global drilling services and products divisions and targeted at the 1,200-m (3,900-ft) NQ market, the upcoming Boart Longyear 4200 surface exploration drill features the safest and most flexible rod management sys-tem in its class. The rig includes the industry?s first, truly hands-free rod handling system. This increases operator safety on the jobsite. In addition to the rod handler, the rig also features many new innovations that boost productivity and rig efficiency while minimizing the risk of downtime due to component failure or operator error. Boart Longyear has also included an intelligent PC-based operating system designed to allow complete drilling control as well as diagnostics reporting for the rig.

Jan 1, 2009

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By Carlie E. Banks

Tasks during Phase I of this contract effort were performed in four principal functional areas. These were geology, hydrology, reclamation and mining. Data were gathered from literature reviews, mine visits, survey of manufacturers, consultation with government agencies, and unpublished or private communications with contractors and consultants. The data collected were analyzed for omissions or inaccuracies, then organized into tables, graphs and flow charts to provide a concise body of technical and cost data suitable for the engineering analyses required in Phase II of this contract. Maps illustrating estimated grade and thickness of the oil shale were prepared, some of which are included as exhibits to this report. A preliminary mine layout was performed to test the completeness of the collected data.

Jan 1, 1975