Search Documents

By Elliot Schwartz, Julian Szekely

"In this paper we describe an experiment that was recently performed on the IML-2 Space Shuttle mission in which the thermophysical properties of molten metals were measured using electromagnetic levitation. In the planning of these experiments calculations had to be performed to predict the levitation and stirring forces, heating rates, sample deformation, and internal flows within the sample. These predictive calculations were essential for both the planning of the experiments and for the re-planning of experimental runs during the actual Space Shuttle mission.Introduction""Materials Processing in the Computer Age"" involves the use of mathematical modeling to obtain a quantitative understanding of the phenomena that govern materials processing operations. Microgravity, or space shuttle experimentation represents a specific case in point here; the very high cost of the space shuttle flights, the very limited flight opportunities that are available, and the tight resources aboard a shuttle clearly mandate that these experiments be very precisely planned and that all possible opportunities for mathematical modeling be fully exploited.The purpose of this paper is to present the results of calculations performed for the planning of a space shuttle experiment involving electromagnetic levitation and wherever possible present a comparison of the computational predictions with both experimental measurements and asymptotic analyses. Finally we shall seek to discuss the practical implications of both the computational methodologies and the potential experimental findings."

Jan 1, 1994

By Christine P. Viecelli

As Phelps Dodge Corporation addresses the environmental challenges of the 1990's, water management has become a key element in an overall waste minimization strategy. The Phelps Dodge Hidalgo copper smelter has implemented a comprehensive water management program that includes management of both fresh and process water utilized by its pyrometallurgical operation. Two major technological strategies are being implemented. They are the design, construction and operation of a raw water pre-treatment facility to allow increased evaporation within cooling towers thereby minimizing blow down, and the use of a brine concentrator to treat and recycle significant quantities of process water. The end result of this program is a significant reduction in raw water pumped from the underlying aquifer into the facility as well as a decrease in process water which must be impounded or otherwise treated.

Jan 1, 1992

By B. Mishra, W. A. Averill

"The application of various hydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, ego metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been investigated and suggested for dealing with some of these wastes and scrap material.The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EM] and decontamination and decommissioning [D&D].IntroductionThe high temperature carbothermic or metallothermic smelting reduction methods for metal production are associated with the generation of significant quantity of waste as slags, flue dusts, sludges, residues, effluent salts etc. Certain hydrometallurgical processes also generate lots of aqueous waste due to the inherent nature of the technique. Also, the gas-based reduction processes are not applicable to many stable metal compounds, such as alumina, titania, beryllia, lanthanide and actinide oxides, etc. due to thermodynamic considerations. All these methods cause substantial environmental hazard. There is a need to develop alternative processes which have low waste or ideally a ""zero-waste"" generation.Pyrochemical processes using molten salts provide a unique opportunity for the extraction and refining of many reactive and valuable metals either directly from the beneficiated ore (aluminum, beryllium, neodymium, plutonium, uranium, etc.) or from other process effluent that contain reactive metal compounds. The processes reduce metal compounds electrolytically (A12O 3 and BeCI2) on a carbon anode or by calciothermic reduction (Po, Nd). The by-product, in the latter case, is a calcium oxide saturated halide salt. The waste-treatment to recycle the halide has to be done as a separate step or stored as a contaminated waste. A successful separation technology can provide a new insight to the waste minimization strategy for the nuclear industry."

Jan 1, 1996

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By T. H. Jeffers

The U.S. Bureau of Mines' Salt Lake City Research Center. has developed porous polymeric beads containing immobilized non-living biological materials for extracting metal contaminants? from wastewater&. Immobilized biological materials include peat moss, algae, biological polymers, and other materials that demonstrate high .affinities for heavy metals. The beads, designated as BIO-FIX beads, have distinct advantages over traditional methods of utilizing biological materials in that they have excellent handling characteristics . and can be used in conventional processing equipment or low-maintenance systems.. Toxic metals such as copper, cadmium, zinc, lead, and mercury are several of the many heavy metals effectively removed from mine wastewater& using B'IO"FIX beads. Continuous cyclic testing indicated that the beads continued to produce treated effluents which met National Drinking Water Standards (NDIJS) after 175 loading-elution cycles, Adsorbed metals were removed from the beads using dilute ?mineral .acids. In many cases" the extracted metals were further concentrated to enable processors to reclaim the metals, thus minimizing the generation of a hazardous sludge. Tests indicated that use of the beads in a low-maintenance system was particularly effective for treating remote acid mine drainage waters? and small toxic seeps from hardrock mining districts ..

Jan 1, 1991

By B. R. Baldock

The converting of high-grade nickel matte for production of low-sulphur matte or nickel metal is a process which has eluded metallurgists in the past because of the limitations of conventional converting furnaces. The high temperatures required and the refractory nature of nickel oxide has prevented practical success in a process which has been known to be theoretically feasible for a long time. The Ausmelt top submerged lancing system is capable of operating under close control of the smelting conditions. High temperatures and both rapid oxidation and rapid reduction can be achieved. These features have provided the basis for successful pilot plant trials of the desulphurisation of high-grade matte from the Kalgoorlie Nickel Smelter. Sulphur level in product was lowered from 20 to 25% to as low as 0.2%, with iron levels in matte in the range of 1.0 to 3.5%. The theoretical background of matte desulphurisation is surveyed and the pilot plant operations described. The implications of the results in relation to commercial plants and possible refinery operations are summarised.

Jan 1, 1993

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By Thais Cristina da Costa Caldas, Carlos Mauricio Fontes Vieira, Alline Sardinha Cordeiro Morais, Sergio Neves Monteiro

"This work has as its objective to evaluate the effect of the incorporation of a glass powder waste obtained from discarded and Hg-cleaned fluorescent lamp into clayey ceramics used to fabricate bricks and roofing tiles. Formulations were prepared with incorporation of the waste in amounts up to 10 wt.% into the clayey body. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa to fire at 850 and 1050°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy. The results showed that the waste incorporation significantly improved the evaluated properties mainly at 1050°C.IntroductionFluorescent lamps use mercury as a main component for its operation. This metal is potentially toxic and can contaminate soils, animals and water bodies. The problem is aggravated if considerations are made with respect to the amount of lamps that are commercialized and discharged in emergent countries like Brazil [ 1].By using appropriate recycling processes applied to discharging fluorescent lamps it is possible to reuse most constituents of these lamps into new productive processes. A study has shown that one million common fluorescent lamps can generate 900,000 tubes of clean glass [2]. Moreover, this Hg-cleaned gloss may be recycled in different products.In fact, to recovery and recycle all materials that constitute the lamp instead of discharging them. This action protects the soil avoiding the formation of environmental passives [3]. It is also relevant to mention that the glass from fluorescent lamps is 100% recyclable while its permanence in the environment would correspond to very long time pollution, since its decomposition time is undetermined [4]."

Jan 1, 2011

By Niels Verbaan, Ralph Fitch, Charlotte Forstner, David Dreisinger

A process has been developed to extract gold, silver, indium, gallium, lead, copper, zinc, and other metals from a large resource using an oxidizing acid chloride heap leaching technology. The ore is crushed and/or ground to improve reactivity and then contacted with a solution containing NaCl-HCl-NaOCl. The value metals are leached into solution as chloro-complexes. The leachate is treated in a series of separation and recovery processes to produce separate saleable or disposable products. The paper will provide a summary of process development and application to a silver-indium ore from Bolivia. The possible application of the process to other ore types will be presented for discussion.

Jan 1, 2015

By G. Mawire

The extraction of scandium from its oxide with a task specific ionic liquid [Hbet][Tf2N] offers potential advantages of lower energy consumption, recycling of the extractant and reduced environmental impact compared to conventional methods. In this paper, the influence of reaction temperature, solid to liquid ratio and water to the ionic liquid ratio on the extraction of scandium from a synthetic scandium oxide (Sc2O3) system was studied. The influence of investigated parameters on leaching was very significant as approximately 98% scandium was extracted from its oxide after 72 h. Furthermore, the ionic liquid also selectively extracted 47% scandium after 48 h from a mixture of pure metal oxides containing oxides of tantalum, niobium, and scandium. The research demonstrated the potential of [Hbet][Tf2N] to selectively extract scandium from columbite processing tailings and other scandium bearing ores like Ixiolite, Heftetjernite and Tantalite which predominately contain tantalum and niobium.

By Y. Waseda, S. V. Gnyloskurenko

"Present paper reviews the various processes for making of metallic foams. These methods are classified in accordance with the state of initial metals - liquid, powdered and ionized. Liquid metal can be foamed by direct inputting of gas into melt, using gas releasing foaming agents or producing supersaturated metal-gas solutions. This group also includes methods creating voids in the melt. Powder route is based on using powdered matrix metal with foamable precursor materials. Finally Deposition techniques allows making highly porous metallic structures using ionized metal.Experimental study presented shows importance of wettability in bubble formation at gas blowing into melt simulation liquid (water) through holes. Good wettability of injection holes by water ensures formation of bubbles with smaller sizes that effect to the final foam structure.IntroductionOne of the objectives of future production technology is to make of lightweight constructional materials while achieving improved property and good economy as well.The most perspective lightweight materials are cellular or foamed materials that are Wide8pread. in nature and have a growing interest in industry and everyday life.Even metals and metallic alloys can be produced as cellular solids or metal foams beside of the traditional engineering materials such as polymers, ceramics or glass. Recent developments in metal foams, especially aluminium, have produced a new class of lightweight materials."

Jan 1, 2000

By L. M. Luckevich

Gypsum is a product from the neutralization of sulfuric acid by lime or limestone. This paper will discuss specifications for gypsum used in wallboard, cement and agriculture and the factors affecting its utilization potential. Process conditions during the neutralization which enhance or inhibit utilization potential will be included. In addition, this paper provides a technical and economic perspective of the gypsum industry in North America with a view to the factors affecting the utilization of synthetic gypsum in traditional applications. Current production and consumption of natural and synthetic gypsum in Nonh America are described and the impact of their differences on utilization options are discussed.

Jan 1, 1996

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015

By Adriana de Aquino Soeiro da Silva, Joao Alves Sampaioa, Luiz Carlos Bertolino, Francisco Manoel Garrido, Marta Eloisa Medeiros

"Brazil has a large agricultural potential and its production success is related to the chemicaland physical soil characteristics. Therefore, the demand in the use of a great quantity offertilizers to compensate the low amount of nutrients in the soil includes about 40% of foodproduction costs. In order to develop economical alternatives to traditional fertilizers, rockswith potential use in agriculture will be studied. In this work the potassium rock, a greensandslate, will be chemically and structurally characterized for the development of a potassiumthermophosphate. This alternative fertilizer will be obtained based on a fusion of a ponderedmixture of potassium, magnesium and phosphate rocks to be applied in the Brazilianagriculture. Preliminary characterization results indicate that the greensand slate presents ahigh percentage of glauconite, quartz and micas.Keywords: Potassium thermophosphate, alternative fertilizers, greensand slate.IntroductionBrazil has a great agricultural potential and its production success is closely related to thesoil's chemical and physical characteristics. However, the country's soils present lownutrients content and high acidity due to weather conditions. Thus, the use of a high amountof fertilizers makes up for the soils' lack of nutrients and accounts for 40% of food productioncosts. Therefore, research on obtaining new alternative fertilizers is a constant worry due tothe increase on food demand [ 1].The lack of raw material for the preparation of NPK fertilizers in Brazil is a concern and theissue of potassium fertilizers a priority. Such a fact is because in 2008 only 608.000 tons ofKCl were produced, corresponding to just 10% of the Brazilian necessity. Thus, the use ofrocks as agricultural nutrients can contribute to reduce the need for industrial fertilizers.This way, the development of a new agricultural raw material originated from a rock thatalready exists in the country's soil is of great importance for the mineral and agriculturalsectors."

Jan 1, 2011

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, Pso, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of 02 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By Yiling Zhang, Paul A. Salvador, Gregory S. Rohrer

"Photocatalysis utilizes solar energy to produce hydrogen by splitting H2O. When a thin film of photocatalyst TiO2 is supported on a ferroelectric BiFeO3 substrate (band gap ~2.5 eV), the TiO2/BiFeO3 heterostructure is capable of photochemically reducing Ag+ to Ag0 in aqueous solutions under blue light with enhanced efficiency. The observation of spatially selective silver patterns on surface of the heterostructure after reaction suggests that photogenerated electrons and holes in ferroelectric BiFeO3 are driven in opposite directions to reduce their chance of recombination. Comparisons of the amounts of reduced silver on TiO2 film grains with distinct phases/orientations show that the reactivity is mildly preferential on anatase TiO2 phase and does not strongly depend on crystallographic orientation of BiFeO3.IntroductionTitania (TiO2) is capable of photocatalytically converting H2O to hydrogen and oxygen under the irradiation of ultraviolet light. [1, 2] One of the limiting factors for titania to be used as an effective photocatalyst is its band gap. Because the absorption edges of rutile and anatase titania are at 3.0 eV and 3.2 eV, respectively, they can only absorb light in the UV portion of the spectrum, which is about 3% of the available solar energy. [3-5] This limitation has motivated attempts to modify the absorption edge of titania so that it can absorb visible light.One strategy is to substitute a portion of the titanium and/or the oxygen with other atoms. There are numerous reports on visible light absorption of titania by doping and co-doping of Cr, V, Mo, Sb, Fe, N, S, C, and F. [6-34] Another strategy is to add an adsorbed molecular species that absorb visible light and donate an electron or hole to the titania, such as organic dyes [33, 35, 36] and Ce3+/Ce4+. [37, 38]The strategy in the present work takes the approach of depositing a pure titania thin film on a visible light absorbing substrate BiFeO3 to induce visible light activity of the heterostructure. BiFeO3 is a semiconductor with a band gap of about 2.5 eV [39-41] and is photocatalytically active in visible light. [42, 43] It is also ferroelectric with spontaneous polarization along pseudo-cubic <111> directions of 6.1 µC cm-2. [44] The spontaneous polarization gives rise to internal electric fields that drive photogenerated charge carriers, namely electrons and holes, in opposite directions to reduce their chance of recombination. [45-47] Additionally, the separation of electrons and holes leads to the spatial separation of reduction and oxidation half reactions so that the back reaction of intermediates is also suppressed. Such charge carrier separation has been reported in TiO2/BaTiO3 heterostructures with UV light illumination. [48-51] The TiO2/BiFeO3 heterostructures in this work combine both advantages of the relatively narrow band gap and the internal fields in BiFeO3 to enhance the overall photocatalytic activity."

Jan 1, 2014

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980&apos;s and 1990&apos;s for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum &apos;supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998