Search Documents

By Yang Tian-zu

The separation of precious metals from base metals containing in gold-antimony alloys by selective chlorination leaching under controlling potential was studied in this work. The effects of the consumption of hydrogen peroxide, the concentration of hydrochloric acid, the concentration of sulfuric acid, leaching temperature, leaching time and the liquid-solid ratio in hydrochloric acid system on the leaching efficiencies of the base metals have been investigated. The optimal leaching conditions of the gold-antimony alloys are as follows: hydrochloric acid concentration 4.0mol?L-1, sulfuric acid concentration 1.2mol?L-1, liquid-solid ratio L:S=7.5:1, the leaching temperature 80 0C, leaching time 2h, and the oxidation potential of the leaching system 400±20mV( vs SCE).The leaching efficiencies of copper, nickel and antimony are more than 99% and the gold leaching efficiency is about 0.042% under the above leaching conditions. The base metals containing in the gold-antimony alloy are separated from the precious metals thoroughly.

Jan 1, 2006

By Chen Yongming

In order to eliminate the serious environmental pollution caused by low concentration of sulfur dioxide smoke in antimony smelters, a new smelting process, named as reducing-matting smelting, is proposed in this paper. The effects of technical conditions such as smelting temperature, smelting time, Pyrite cinder addition and the amount of additive on the smelting of stibnite concentrate have been investigated by the method of single-factor experiment. The results show that the optimum conditions are as follow: The amount of pyrite cinder is 1.2 times of its theoretical amount. The addition of soda and sodium sulfate is 15% and 72.6%, respectively, to the amount of stibnite concentrate when the total amount of sodium is 30%. The reducing-matting smelting is conducted at 1100°C for 2h then the smelting temperature is raised to 1200°C for 50min. Under the optimum conditions, the direct and total recovery ratio of antimony can gain 90.99% and 98.87%, respectively, and the fixed ratio of sulfur is higher than 99%.

Jan 1, 2006

By Zhenyang Wang, Yiran LIU, Xiangdong Xing, Jianliang Zhang, Zhengjian Liu

Basic characteristics of marine placer were systematically studied by chemical analyze, scanning electron microscope and X-ray diffraction in this paper. It could be found that the marine placer mainly consists of titanomagnetite and titanohematite. A series of experiments were performed to investigate reduction-magnetic separation for Fe and Ti from the marine placer. Effects of reduction temperature, reduction time, carbon ratio, magnetic density, and grinding fineness on the reduction-magnetic separation process were investigated. And the optimal process parameters were obtained as follows: the reduction temperature 1300, the reduction time 30 min, the carbon ratio 1.1, the magnetic density 50mT, and the grinding fineness of 0.074μm 86.34%. Under such conditions, the metallization rate, iron grade of magnetic substance and iron recovery reached to 94.23%, 97.19% and 90.28% respectively, and the titanium grade in non-magnetic substance and recovery of was 57.94% and 87.22% respectively. The effective separation of iron and titanium could be achieved in reduction-magnetic separation process.

Jan 1, 2015

By Bingyi Bai, Wangjun Peng, Yanling Guo, Jieyu Zhang, Guoding Gao

The phase transformation of bayan obo ore with high concentration of iron and calcium was reduced at temperatures no more than 1000℃ were investigated in this study. The samples with insufficient carbon were treated at the temperature using a vertical furnace with a thermogravimetry (TG). The mineral phases and content were examined using Xray diffraction (XRD) and X-ray fluorescence spectroscopy (XRF) respectively. The complex phases of bayan obo ore transformed to some simple phases after treated with different content of carbon at the same temperature for 10 hours. The result of XRD、 XRF and TG showed that the reduction degree of Fe3O4 phase formation varied with the temperature and the carbon content of bayan obo ore.

Jan 1, 2015

By Masayasu Kawahara

"The extraction and separation of nickel, cobalt and copper were investigated with a solvent impregnated resin which was produced from UX84-I and XAD-4. The extraction behavior of metals with the solvent impregnated resin is similar to that with solvent extraction. The extraction ability of solvent impregnated resin improves when using finer particle resin and with a higher concentration of extraction solvent.IntroductionSolvent extraction is well known-as a method for separation of metallic elements in solution. However there are problems with intermediate phase and solvent loss. Ion exchange resin is also used in hydrometallurgy, but it is not fit for separating a large quantity of metals. Amberlite XAD-4 resin is known as a absorption agent of organic matter in water. It is expected that the resin which has the ability of extracting metals can be made by absorbing organic extractant on XAD-4 resin In this study, solvent impregnated resin (SIR) was produced from LIX84-I and XAD-4, and extraction and separation of nickel, cobalt and copper were conducted using SIR. The extraction properties of SIR were investigated, and a comparison between ordinary solvent extraction and SIR was made.Experimental ProcedureAmberlite XAD-4 was used as absorption resin for the organic extractant in this study. The physical properties of XAD-4 are shown in Table I. Amber lite XAD-4 has a large surface area and shows good ability to absorb organic matter in water, but the: resin does not have the ability of exchanging metallic ion."

Jan 1, 2000

By Jan G. H. du Preez, C. Viviers, B. J. A. M. van Brecht, H. E. Rohwer, Nicole M. Sumter

"At the basis of metal ion separation lies some particularly metal ion specific chemical property which lends itself towards exploitation. This could be in the form of an anionic complex or a neutral chelate complex. In the former a cationic centre with a particularly high affinity for the complex will have to be designed. In the latter case a stereospecific chelate ligand containing the correct symmetry and type of donor atoms will have to be designed. In both above cases the ""active centre"" can be entered in a from that it can function in different media of hydrophobicity, eg a precipitant, a resin or a solvent extractant. Recent results obtained in this laboratory will be used to illustrate how the above variables can be exploited to develop improved processes for the separation of base metal and platinum group metals.IntroductionThe separation of metal ions in hydrometallurgy can be performed broadly speaking with two major aims. Firstly the separation/removal of a certain group of metal ions, either as a means of preconcentration or as a removal from effluent as part of a purification process and, secondly the removal of a specific metal ion from an industrial stream in order to produce a specific metal in a pure form. This latter operation is by far the most difficult of the two and is becoming more so in the light of the fact that the world is moving in the direction of lower grade ores and increasing pollution. Such a process can be divided into three essential parts, firstly the molecular one in which an active centre is required to obtain specificity, secondly a matrix within which this active centre must function, i.e. as part of a resin or solvent extractant and thirdly the design of the total system to optimize the realization of the operation."

Jan 1, 1996

By David Hughes

The paper covers the utilization of on-line analysis in process control of solvent extraction in nickel leach solvent extraction processes in Finland and Australia and in copper heap-leach and solvent extraction in Chile. The goals of and requirements for controlling the solvent extraction stages of the processes are reviewed. The applications at three plants are compared. The development of the technology used is reviewed and design considerations are discussed. Requirements for on-line control and analyzer performance are compared. A new generation of analyzers and its effect on the set-up process of a project is introduced.

Jan 1, 2003

By W. L. Cornell

Bulk sulfide concentrate produced from Missouri Pb ore concentrator tailings must be reground to liberate sulfide values for subsequent sepa-ration. Studies to determine grinding parameters for optimum liberation were carried out using optical microscopy coupled with image analysis. The major sulfide phases present in the ground mineral particulates are marca-site, pyrite, sphalerite, galena, chalcopyrite, siegenite. and bravoite. Results showed that the base metal minerals were liberated by grinding to 74 micrometers (200 mesh), but the siegenite and bravoite required grinding to 20 micrometers or less to achieve liberation. Both the experimental method and results are presented.

Jan 1, 1987

By Fathi Habashi

In the past five years Cuba has been attempting to more than double its nickel production by constructing two new ammonia leaching plants. No metals are yet produced on commercial scale but a variety of oxides and sulfides. This report updates the Cuban nickel industry as a result of two visits : one at the invitation of the Cuban Ministry of Basic Industries in 1987 and the other as a consultant to the United Nations for the Cuban Laterite Project in 1989.

Jan 1, 1993

By R. G. Haire

Studies of the f-elements under pressure provide important insights into their solid state chemistry and physics. From such studies, of the elements and their alloys, it has been established that the normally localized f- electrons of several of these elements can become, involved in bonding under pressure. The electronic behavior of f-element compounds under pressure tend to be more difficult to interpret, due to the variety and the nature of electronic orbitals that are present. The 4f-elements and some 60% of the 5f-elements have been studied under The systematic comparisons that have been established for these materials are discussed.

Jan 1, 1992

Four slag types covering the range of Fe-Ca-Si-O compositions and two iron blast furnace slags were melted at 1300 °C and doped with 1% of arsenic, antimony, cadmium, zinc and chromium. The melts were either slow cooled or quenched and the solidified slags were leached according to TCLP procedures. The morphology of the solidified slags was characterised using XRD, optical and electron microprobe techniques. Theoretical considerations showed that the capacity of the molten slag to hold the above toxic elements depended upon slag basicity and this was confirmed in practice. The experiments showed that the leaching of the toxic elements was a function of surface area and the phases present, both of which were affected by the mode of cooling. Iron silicate slags produced in nonferrous smelting operations and blast furnace slag from ferrous smelting operations both show promise of being suitable media for immobilising low levels of toxic elements and complying with current regulatory requirements.

Jan 1, 1994

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By Shunsuke Yagi

A surface alloying technique was investigated using alternating pulsed electrolysis in an aqueous solution containing a single metal component for the formation of an Fe-Cr layer on an iron substrate. In the process, the iron substrate was dissolved during each anodic polarization of the pulsed electrolysis, providing iron ions in the vicinity of the substrate, while the Fe-Cr alloy was electrodeposited during subsequent cathodic polarizations. A bright, flat, and crack-free Fe-Cr layer with a composition gradient was obtained using a solution containing a trivalent chromium component and a complex forming agent together with some supporting or buffering salts.

Jan 1, 2006

By Ragnhild Aune

In fire refining of copper, the affinities of various impurity elements on dissolved oxygen is of great significance. Further, in the design of oxygen probes in liquid copper, the influence of solute interactions on the activity of oxygen need to be considered in order to evaluate the oxygen concentration in molten copper. The present paper presents a series of measurements of the activities of oxygen in liquid Cu-M-o alloys (where M stands for Mn, Zn, As, Se or Te) carned out by the present group employing the solid electrolyte galvanic cell technique. Extreme care was taken to control the oxygen potentials in the inert gas atmosphere, and to keep the oxygen levels very low in the molten metal. The oxygen content was determined by analysis of the samples taken out from the melt. The results obtained showed that Mn has a strong negative influence on the activity coefficient of oxygen in liquid copper. A similar, but less prominent effect was observed in the case of Zn. Arsenic had no influence on the activity of oxygen in Cu (liq.). Se and Te had slight negative effect on oxygen activities in copper at XQ >10-5, while at lower oxygen levels the interaction coefficients were found to be positive. The results obtained were compared with empirical models for the calculation of interaction coefficients available in literature.

Jan 1, 2003

By Takeshita. Takuo

"In this work, the progress of the HDDR process is discussed mainly on the Nd-Fe-B magnet system. There are three technologies being used for the Nd-Fe-B permanent magnet production; the sintering technique, the rapid quenching annealing and the HDDR process. The HDDR process utilizes· the HDDR phenomenon, in which hydrogen absorbing intermetallic compounds go through as they are heated in hydrogen atmosphere, Hydrogenation - Decomposition Desorption - Recombination. In the HDDR process, these four steps in the HDDR phenomenon are processed by choosing suitable reaction conditions regarding to hydrogen gas pressure, temperature, rate ·of desorption and etc., and we can produce permanent magnet powders of good magnetic properties with microstructures consisting with sub-micron size crystalline grains. In the anisotropic magnet powders, the sub-micron size crystals are being mostly aligned in the crystallographic c-axis direction. Possible applications of the HDDR process to other systems are also discussed.Microstructures of the Nd-Fe-B Permanent MagnetsIt is well known that magnet properties of magnetic materials are very sensitive to their microstructures [l]. This is seen in almost all magnet materials from soft magnetic materials and hard magnetic materials to magnetic memory materials. In this regard, the production technology is very important for the control of microstructures of permanent magnets The Nd-Fe-B magnet is the most powerful permanent magnet as a practical permanent magnet, and its coercivity force is much dependant on the microstructure as is the case for other permanent magnets."

Jan 1, 2000

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By Yuzhe Zhang, Xiaodi Huang, Xinli Wang, Bowen Li, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Likun Li

With the development of the world, the waste tires have been a serious environmental problem. There are about 2 billion waste tires produced all over the world every year and about 500 million waste tires are produced in the United States. Most of the waste tires are land filled, which waste a lot of space. It takes hundreds of years to resolve the macromolecules of waste tire into the standard which does not pollute the environment. Microwave irradiation is a thermal processing way for waste tires decomposition. In this study, the relative dielectric loss factor of the tire at various temperatures was determined to understand the behavior of tires under microwave heating.

Jan 1, 2016

By Ibrahim Yusufoglu, Cem Kahruman, Mert Zoraga

In this study, a strontium sulfate mineral (celestite) was converted to strontium oxalate in solutions containing ammonium oxalate as a reactant. The experiments were carried out under isothermal conditions. The effects of stirring speed, ammonium oxalate concentration, particle size and temperature on the conversion rate were investigated. During the conversion process, definite volumes of solutions were taken from the reactor after different reaction times for the determination of sulfate ions using ICPOES. Fractional conversions of strontium sulfate were determined at different times and fractional conversion vs time diagrams were generated. It was found that the conversion of strontium sulfate was increased by increasing the ammonium oxalate concentration and temperature in addition to decreasing the particle size. The effect of stirring speed was negligible on the reaction rate. It was observed that above 328 K, a protective layer of strontium oxalate was formed on the strontium sulfate particles. X-ray Powder Diffraction technique was used for characterization of solid substances.

Jan 1, 2014

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By Xiang Sun

Microwave processing has been under continuous development as an advanced heating method in modern industries. However, problems with uneven heating still remain. Although heating uniformity is highly dependant on the properties of the materials being heated, proper furnace design to prevent uneven field distribution is another important factor. As an alternative to experimental measurements and adjustments to find appropriate furnace parameters, computer simulation is a convenient method for modeling, understanding, and improving the uniformity of microwave heating. This paper discusses current modeling technologies as well as applicable techniques for improving microwave heating uniformity. The purpose is to give a basic understanding on how to find, analyze, and minimize the problems associated with uneven heating in microwave processing.

Jan 1, 2006