Search Documents

By Jackson M. Langton

INTRODUCTION The Morenci-Metcalf district is located on the southern slope of the white Mountains in Greenlee County, Arizona. Both porphyry copper deposits are four to six miles northwest of Clifton, the county seat, and the new Metcalf mine is situated approximately one mile northeast of the Morenci open pit (Figure 1). Chase Creek, a south-flowing tributary of the San Francisco River, dissects the district and separates the two ore bodies. More than 1,200 exploration and development drill holes have been completed in the district and the Morenci-Metcalf ore bodies have been delineated on a 400-foot grid. Recently initiated drilling programs have revealed new data about deeper protore and associated hypogene alteration. This information, correlated with surface mapping and petrographic studies, was utilized to propose a plausible geochronologic sequence for this region. The reasoning behind this study has been helpful in locating new ore beneath leached capping indicative of only protore mineralization. The scope of this paper is to establish a practical solution to a highly theoretical problem of ore genesis and to familiarize the reader with stratigraphic, structural, and mineralogic events responsible for localizing ore in this district. Continued research will possibly alter the proposed time span and relative displacements, but it is doubtful that the order of events will vary significantly. Geochronologic conclusions are therefore presented as general hypotheses and additional geologic mapping,

Jan 1, 1972

By RIINA SALMIMIES, Paula Vehmaanperä, Antti Häkkinen

The dissolution of iron oxides in mixtures of acids is fairly uncommon but can result in a more efficient dissolution process. The objective in this work was to investigate the dissolution of synthetic hematite powder in mixtures of oxalic and sulfuric acid. Experiments were done at different acid ratios and temperatures. An increase in temperature from 15 to 35 °C increased solubility, whereas an increase from 35 to 50 °C did not change the solubility but had a profound effect on the kinetics. An important finding was that oxalic acid advanced the dissolution process since increasing the amount of oxalic acid in the system resulted in faster kinetics and higher solubilities. The dissolution kinetics were well described with the Kabai model, which was the only studied model able to describe the whole reaction time. However, the solid specific constant a varied for the different acid ratios and this is argued to be a result of changes in the solid phase. The changes in the constant a were not in line with the original study of Kabai, which indicates that a cannot be the solid specific constant but it can be the constant connected to dissolving media describing the changes in the dissolution mechanism.

Sep 23, 2020

Solvent extraction-electro- winning appears to be one of the most important processes for the future in the North American copper industry and for this reason both the SX and EW steps are furtive areas for development. This paper has the objective of reviewing the present state of the electrowinning technology. It discusses some recent equipment developments and concludes by discussing the direction the technology will likely go fn the next decade.

Jan 1, 1985

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin (1961) were the first to develop a model for bubble-particle interaction in flotation from first principles by considering the surface forces in wetting (or flotation) films. The model predicted that the energy barriers to bubble-particle attachment arise from the ζ-potentials of fine particles, which corroborates well with an earlier work of Fuerstenau (1957) reported for the flotation of quartz using dodecyl ammonium acetate (DAA) as collector. In the present work, a series of surface force measurements have been conducted by accurately monitoring the changes in bubble curvature during bubble-silica surface interactions. The curvature changes are then used to determine the capillary force, which is the sum of the hydrodynamic and surface forces. By subtracting the former that can also be determined from the curvature changes, one obtains the surface forces (or disjoining pressure). The results obtained as functions of pH and collector concentrations show that control of the ζ-potentials of bubbles relative to those of the silica surfaces is critical for maximizing the negative disjoining pressure, which is conducive to promoting bubble-particle attachment in flotation.

By V. A. Kharchenko, V. M. Yeremeev

INITIAL PRECONDITIONS To solve tile problem of using the potential reserves of the different coal ranks efficiently (the coal reserves being many times superior in quantity to those of natural gas and oil) one must realise an integrated estimation of the coalfields' and coal deposits' reserves. The actuality of this problem increased especially in the recent years, when the Russian coal industry is being restructured. A structural reorgaisation of this industry, in order to in- crease its efficiency, covers a large spectrum of social and economic problems, comprising a withdrawal from mining the coal reserves that are unsafe from the standpoint of economy and labour protection. According to the information supplied by the 'Rossoogol' company, the Russian coal industry, accounting for abut a fifth of the world coal reserves, has a rather unsafe resource base, for about 5% of the reserves involved in mining do not correspond to the world practice conditions, regarding the coal grade, thickness, geological conditions, proneness to coal and gas outburst hazards. These concern first of all the Moscow, Kizelovsk and Donetsk coal basins, the Prokopievsk-Kiselevsk district of the Kuzbas basin and several other coalfields. Thus, the problem of efficient potential coal reserves' utilization calls for a paramount solution of two basic problems, namely: a) a comparative coalfields' and sections evaluation, and their ranging, in accordance with their industrial importance; b) choosing the 'active' reserves good to be efficiently mined under the present-day conditions. PRINCIPLES OF EVALUATION The investigations that had been carried out make it possible to formulate the following basic principles of the coalfields' reserves' estimation (or assessment). 1. The necessity, possibility and expediency of coal reserves' industrial exploitation are determined by a set of natural, technical, technological, practical, economic, environmental and social factors, thus calling for an integrated and gradual approach to problem solving. 2. One cannot consider the results of same reserves' estimation as being invariable because the former depend both upon constant (mainly natural) and market demands for different grades of coal (those of different power engineering and technological situations), capital investments, material and labour resources, economic (price-forming), technical, technological, environmental and other factors. 3. The rational size and sequence of the operating mines' and reserve sections' resources' involvement into mining depend upon the final aim of posing the problem, whose variants may be (the corresponding limitations being considered) providing for a maximum run-of-mine output (these essentially featuring the past stages of the industry's evolution); providing for a maximum efficiency, measured possibly by the specific or absolute indices of profits an expenses, labour productivity e. al. ; providing for a maximum extraction (maximum integrate utilization) of the known reserves. In this case an important park goes to the economic evaluation (or assessment) of useful application of the by-products being extracted (methane, mine water, rack) compared to the expenses necessary for their utilization. Regarding the steam coal (posing the problem any way it be possible), and extreme limit to the absolute non-efficiency of the coal reserves' exploitation may be posed, using the proportion of energy obtained from the possible amount of the coal to be extracted to the energy consumption necessary to extract, prepare, haul and consume this amount of coal. 4. The most reliable and efficient solutions providing for opening the reserves can be obtained for group of mines, rather than at the level of an individual mine section or an individual mine because it is only in the former case that the possibilities to re- distribute the expenses necessary to develop the good for mining and worse sections and seams can be realized to the greatest extent. Therefore the prospective approach to be considered is the one providing for an integrated organization and choice of the optimum combination of the variants of the ways to use the mines in operation and the free sections of the region in order to satisfy the growing up requirements for coal rather than the one providing for individual mine sections' resources' evaluation. 5. The future possibility and expediency of coal reserves' industrial exploitation will depend upon the prospects to implant at the mines in operation and reserve sections new engineering and technological elements and coal extraction technologies which may essentially change the actual idea concerning the coal reserves worth of being developed in an efficient way. For example, reserves not available to be exploited using conventional coal extraction technology may be regarded as potential resources for in situ gasification, e. g. the operating mines' reserves (non-commercial and non-mined commercial ones), balance and outside balance reserves of the free sections having proved not available to be mined using conventional coal-extraction technologies, as well as the non-extracted reserves of the abandoned and closed mines.

Jan 1, 1996

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By R. Wensel

A composite material consists of two or more dissimilar components. These dissimilar components retain their identities when mixed together and contribute to the properties of the composite. A composite usually consists of two parts, the matrix and the reinforcing material, or extender that is added to the matrix. Typical materials used as the matrix in composites are metals, polymers, and ceramics. The reinforcing material can be added for any number of reasons. For instance, if the matrix is expensive, an inexpensive filler may be added to the matrix to lower the cost of the product without sacrificing properties. An example of this is calcite (CaC03) which is added to systems such as polyvinyl chloride (PVC), to lower the cost. Reinforcements may also serve as a means to enhance the properties of the matrix material. For example, carbon fibers are frequently added to plastics to increase their strength, and glass spheres may be added to plastics to improve flexural strength. Mg(OH)z is added to polymers to give the property of fire retardancy. The latter is the focus of this paper.

Jan 1, 1995

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By Q. Xiao, R. Naidu, W. Li, S. Song

Acid mine drainage (AMD) derives from the oxidation of sulfide minerals, primarily pyrite (FeS2), and is the most severe environmental issue facing the minerals industry. The most common short-term approach to AMD treatment is migration control, such as acid neutralization and metal/metalloid and sulfate removal, through the addition of alkaline materials, including lime (Ca (OH)2), limestone (Ca CO3), gangue minerals and industrial wastes. This requires the continuous input of materials and may result in the production of a vast amount of secondary sludge requiring further treatment and disposal. Addition of chemicals is usually more important in metal/metalloid removal than in sulfate removal unless the sulfate is present in very high concentrations. A more promising long-term strategy for AMD prevention is source control through the complete removal of pyritic minerals and encapsulation of potential risk minerals by coating with impermeable surface layers. This is regarded as the most cost-effective approach, although the mechanisms underpinning this and the implementation procedures are yet to be fully elucidated. It is likely that long- and short-term practices can be combined to optimize the remediation of contaminated mining sites. Some factors such as differing geological and mineralogical characteristics and transportation costs must also be considered for the successful implementation of AMD prevention and remediation strategies. This review also considers some implications for AMD remediation, but the promising bioremediation of AMD is not discussed as it has been extensively reviewed.

By D. H. De Jager

Fluorapatite is an important constituent of the greater part of the basic and ultra-basic rock members of the Complex. The evidence for and role of primary magmatic processes in the development of concentric zones of dunite, pyroxenite, syenite and carbonatite and its consequent bearing on the distribution of apatite are discussed. The presence of at least two generations of each of the latter three rock types indicates the cyclical nature of magmatic activity. Pegmatitic-metasomatic phases corresponding to the major magmatic cycles resulted in emplacement of pegmatoidal assemblages. The abundance of apatite in the pegmatoid can be traced to the composition of its parent magma and its cooling history. Approximately 2.5 million tonnes of phosphate concentrate are produced annually from ores containing from 10 percent to 25 percent apatite.

Jan 1, 1978

By Dan Nilsson

INTRODUCTION A company must have an objective, and that usually is to earn money. In some countries an objective can also be to reduce unemployment in an area or to develop nonindustrialized areas. Government-owned companies can also have as an objective that of serving the com¬munity. This discussion is limited to the consideration of normal companies wanting to earn money. Such an objective, however, has to be defined in more detail. It is not satisfactory only to maximize the total annual profit from, for example, a mining project. In comparison with most other branches, the mining in¬dustry is very capital intensive. When starting a new project, the mining company must invest a lot of money in mines, ore treatment plants, etc. It is normally many years before any income is received from the ore. Fig. 14 illustrates the payments for a new mining proj¬ect with an expected lifetime of 10 years. Whether this project is a profitable one depends on a lot of things. If the company has a shortage of money, it can be impossible to finance the project. Even if the company has enough money, the management may think that perhaps the project may not return the money fast enough. Such limitations will not be discussed here. Suppose that the company has internal funds from its own operation or can borrow them. Since the mining company must invest the money in advance, it is not satisfactory only to add all of the costs during the mine's lifetime and compare them with the total income during the lifetime. The company must include the time value of the capital. In this appendix, the basic investment theory neces¬sary to judge the profitability and costs of mining proj¬ects will be discussed. INVESTMENT THEORY Time Value of Money If a private person has a dollar and puts it into a bank, he or she will receive interest. If the interest rate is r%, the value after one year will be $(1 + r), after 2 years $(I + r)2 , etc. The interest rate represents the time value of money. If the same person wants to have $1 in the bank af¬ter one year, he or she has to put $(1 + r)-1 in the bank today. If the person wants $1 after 2 years, it is neces¬sary to put $(1 + r)-2 into the bank today, etc. So one dollar today is worth more than one dollar tomorrow. It is, of course, not correct to compare money at differ¬ent times since each dollar has a different value. It is necessary to transform all payments to the same point in time. That is called the calculation of the capital value of a cash flow, and to do this an interest rate is used. In the same way, the cash flow from a project like that shown in Fig. 14 can be translated to any other point in time. Most common is to translate all payments to the beginning of the mining period. That capital value is often called the present capital value. Interest Rate What interest rate will the company use? A com¬pany, just like an individual, has the basic alternatives of keeping its money in the bank and receiving interest, or borrowing money from a bank and paying an interest rate. The interest rate represents the time value of money for the company. If the company has a shortage of money, or many good potential investment projects, it has to use a higher interest rate than if it has a lot of money available. Most companies also increase their interest rate as a hedge against the risk involved by using money for uncertain investments, because of taxes, etc. Capital Value When the interest rate has been decided, it is possi¬ble to estimate the capital value of a project. Here the discussion will be limited to the estimation of present capital values. Suppose that one wants to know the present capital value of $1 (Fig. 15), which will be received after n years. To transform it n years back in time, one must multiply it by the factor (1 + r)-, where r is the inter¬est rate the company uses. Table 1 gives these factors for different years and interest rates. Example: At the end of year 5 a mining company has to invest $50 million in a new mine. What is the present capital value at the end of year 0? The company uses an interest rate of 15%a.

Jan 1, 1982

By Roderick K. Davey

The objective is to develop a short-range mining plan which satisfies management and operating criteria and also "dovetails" with the long-range mining plan. In the past years, this objective was accomplished entirely by manual methods. Today, the computer is used to assist the engineer with this task. The results provided by these programs usually are incomplete and require further manual manipulation. The advantage of using the computer programs is that the program can be used to evaluate alternative plans on a first-cut basis minimizing the manual work. Subsequently, the most promising alternatives can be analyzed in more detail, commencing with the first-cut results. In this specific case history, one technique for using computer programs to assist with short-range mine planning will be discussed. Some of the basic operating and management criteria considered directly and indirectly are as follows: (1) operating criteria which include minimum and maximum shovel cut size, equipment performance, haulage roads, requirements for blending, and plant capacities; and (2) management criteria which consist of production requirements, cash flow requirements, return on investment, market demands, and availability of capital.

Jan 1, 1979

By Ali Behrad Vakylabad, Esmaeel Darezereshki, Babak Koohestani

As a by-product of the steelmaking industry rich in iron and zinc, electric arc furnace dust (EAFD) landfill disposal is restricted in many countries due to the metal lixiviation risks. Several approaches have been examined to recycle or reuse EAFD. Hydrometallurgical methods mainly include the preparation of pregnant acid leached solution (PLS) using inorganic acids followed by selective metal recovery using different methods. We herein proposed a hydrometallurgical process initiated by acid leaching and finalized by thermal treatment to produce nano-ZnO from EAFD. At the condition of this study, only 67% of zinc was leached by sulfuric acid from EAFD into PLS while 98% of surplus leached iron was removed through precipitation by sodium hydroxide. Additional purification of iron removed PLS was accomplished using di-2 ethylhexyl phosphoric acid to extract Zn+2. The addition of ammonium hydroxide to purified PLS provided (Zn(OH)2)3(ZnSO4)(H2O)5 as the final precursor for nano-ZnO that ultimately transformed to nano-ZnO (60 ± 6 nm particle size) at 850 °C. The achieved results were scrutinized through various tests and analyses including TEM, XRD, SEM, EDS, FTIR, and TGA.

Mar 10, 2021

By M. S. Moats

In the 1990?s, Técnicas Reunidas developed the Modified ZINCEX® Process to recover zinc from ores and secondary materials. The heart of this process was the use of solvent extraction to produce purified zinc electrolyte instead of traditional zinc dust cementation. This development was commercialized by Reunion Mining and Anglo American for primary ore at the Skorpion mine in Namibia with the first SHG zinc produced in May 2003. Horsehead Corporation through Horsehead Metal Products, Inc., its wholly owned subsidiary, is presently commercializing the MZP for the treatment of Waelz oxide. This paper will review open source information about the lessons learned and process modifications that have occurred at Skorpion over the past decade. It will also provide an update on Horsehead?s facility being constructed in Rutherford County, North Carolina.

Feb 23, 2014

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.' Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this non-hydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1978

By R. S. Datta

Regulations on sulfur emissions have caused the electric utilities to evaluate various methods of meeting them. Low-sulfur, low-volatile coals can be burned alone or blended with high-volatile? coals. This option may be a cost-effective alternative to the installation of scrubbers on coal-fired combustion systems. In some blending applications, problems may be encountered because the low sulfur content and high calorific value of the low-volatile or other clean coal allow it to economically upgrade extremely poor quality coal. While this is done to meet specification purposes, actual boiler performance may be dominated by the poorer quality coal. Thus, the reputation of the low-volatile or other clean coal suffers. As a result of laboratory and full scale testing, conducted over the last five years, a model has been developed to evaluate the relative combustion characteristics of various coals and coal blends. A database for different coals has been gathered. This paper presents the model and shows how power plants and coal mine personnel can use it to evaluate their coals from different sources. It can be used to blend two or more coals from different sources so that thee blended coal has flame stability characteristics which are similar to those of the baseline coal.

Jan 1, 1991

By Xie Junjie, Li Shina, Ma Ruixin, Min Changli, Yin Zichen, Li Kang, Shi Zhuonan

Cesium and rubidium were effectively separated by zinc ferrocyanide coprecipitation method, and the effect of precipitant addition amount on the separation of cesium and rubidium was studied. Under the conditions of Zn/Cs molar ratio of 0.45 and Zn/Fe molar ratio of 1, the precipitation rate of cesium is 84.01% and the separation factor of Cs/Rb is 164.65. The thermogravimetric curves of the sediment were measured, and the effects of roasting temperature, roasting time, and leaching liquid/ solid ratio on the extraction of cesium were studied. Almost all of the cesium was extracted under optimal conditions: roasting temperature of 600 °C, roasting time of 3 h, leaching temperature of 25 °C, leaching time of 0.5 h, and liquid/solid ratio of 5:1 mL/g. After the leaching process, the leach liquor with high concentration of cesium of 80.17 g/L was obtained. Finally, the leach liquor was further purified by solvent extraction, and the purity of the cesium chloride product reached 99.66%.

Mar 17, 2024