Search Documents

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012

Tunnel damage from explosion and earthquake excitation is correlated with strain and particle motions. Critical strains and motions are then correlated with focal distance, which is so small that permanent strains are highly likely. The shaking process is then numerically modeled to investigate the effects of excitation frequency and joint orientation. The models confirm that near cavern blocks slide intermittently only at relatively high particle velocities during periods of low joint normal stress. Larger displacements occur with relatively small shear wave lengths or relatively high frequencies. Variation in joint orientation and rock mass dilation result in changes in displacement.

Jan 1, 1985

By H. Akbari

The ordinary Portland cement (OPC) is the key pozzalonic component of the concrete mix, widely used as the construction material world-wide. Billions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of CO2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic CO2 emission each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon foot print of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the non-metallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned to extract some of the valuable metal oxides from fly ash prior to using the major non-metallic portion of the fly ash for geopolymer concrete application. The results obtained from this study exhibited that the compressive strength of the geopolymer concrete compares favorably with that of the conventional concrete prepared using the OPC.

Feb 27, 2013

By K. A. Larsen, J. L. Ariail, C. M. LaRosa

This article discusses the evolution of U.S. laws and policies towards environmental remediation at mine lands over the last 20years, the opportunities that these changes present for reuse, and the remaining challenges associated with community capacity for effective reuse planning and implementation. Emerging initiatives by the U.S. Environmental Protection Agency and Department of Interior for addressing these challenges are discussed.

Jan 1, 2004

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By Bahadir Ergener, Angel Maria Tobar Escudero, Sandra Nowosad

Modern mining companies are increasingly turning to integrate digital technologies and circular economy (CE) principles to increase the sustainability of their operations. The so-called “mine of the future” is envisioned as a smart, integrated system where technologies such as automation, artificial intelligence, digital twins, and real-time data analytics work in harmony with human decision-making and environmental responsibility. Already in 2018, McKinsey and Co. identified that the three drivers that would define a technology-enabled change in mining would be technology, including digital, analytics and automation, management systems able to identify the potential and value of the new technologies, and the culture and capabilities of the organisation, leaning to more agile and responsive organisations. From the three drivers, in the last five years most developments have been centred in the first one. Yet despite rapid advances, the adoption of new technologies across the industry today remains uneven and often slower than expected. Furthermore, it has been identified that the problem on the technology uptake often relay on the lack of operational readiness, process incompatibility or misalignment, and resistance to change within the mining operation. At the same time, leading companies like Rio Tinto, BHP, and Anglo American have each launched major digital transformation programs. Rio Tinto, for instance, operates one of the world’s largest autonomous mining fleets and has integrated digital technologies across nearly all its operations (Rio Tinto, 2025). BHP is actively investing in information and communication technology (ICT) development as artificial intelligence, big data analytics and robotics, and has partnered with battery companies to pursue circular economy initiatives. Only in 2024, their ICT spending reached US$ 438.3 million (Global Data, 2024). Anglo American has rolled out its FutureSmart Mining™ framework, explicitly aligning innovation with circularity and sustainability goals (Anglo American, 2025). The accelerating pace of change across leading mining companies along with the uneven adoption in the technology uptake clearly state how digital transformation is no longer just about implementing new tools, instead it requires a fundamental shift in how people, processes, and culture are aligned. Addressing only the technical layer, while neglecting the human and organizational dimensions, leaves transformation efforts fragile and unsustainable. As the industry must act decisively to close this gap, the true test of transformation is today centred in changing behaviours, mindsets, and systems. Even at the listed leading companies, initiatives have encountered cultural and structural resistance that are relatable to the industry in large: siloed departments fail to collaborate, procurement teams focus on upfront costs rather than lifecycle value, and operators are often excluded from early-stage planning, reducing buy-in. In many cases, a lack of communication or failure to link technology to real operational bottlenecks leads to disengagement at the ground level. This friction reveals a broader issue: mining organizations have historically treated technology and culture as separate domains, when in fact they are deeply interdependent. To address this, the authors propose a systems engineering approach focusing on the mining operations as a complex socio-technical system composed of people, processes, and technologies. Systems engineering offers tools and frameworks for mapping interactions, aligning incentives, designing for feedback and adaptation, and integrating change across organizational boundaries. Specifically, besides technical requirements, it demands treating culture not as an afterthought or side-effect, but as a design variable that must be intentionally shaped alongside infrastructure and workflows. This paper explores how this approach can be applied in practice, by analysing a real-world case scenario where resistance to innovation was overcome not by technical capabilities alone, but through alignment of stakeholder incentives, thoughtful communication, and cultural integration. A particular focus is set on the adoption journey of the Powerbit X, a drill bit technology with significant potential for operational and environmental gains.

Feb 22, 2026

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

Oil sands processing generates huge volumes of slurry, known as tailings, that is being stored in tailings ponds. The volume of produced tailings is a very important factor in oil sands surface mine planning, because the available area for dam construction is limited to the lease areas. On the other hand, oil sands operators cannot leave mine sites without reclaiming the tailings ponds. Since most of the reclamation material is generated in either oil sands mining or processing, it is reasonable to include reclamation material requirement as part of long-term mine planning. In this paper, an integrated optimization framework is proposed to maximize the net present value (NPV) of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. A sample bitumen processing flow sheet is used to formulate the volume of produced tailings, based on Clark hot water extraction method. To verify the proposed model, it is coded in Matlab and run using CPLEX. Run results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Feb 27, 2013

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By Gregory D. Savage, Bruce M. Everett

Introduction The growing role of Colombia as a major supplier of internationally traded steam coal has been widely discussed in the industry. Although Colombian coal has been produced and exported in small quantities for a number of years, the country's position as a major coal exporter began in earnest in 1985 with the first commercial exports from the Cerrejon North Block Project. The mine is located on the Guajira peninsula in northeast Colombia, about 145 km (90 miles) from the coast (Fig. 1). In addition to the mine itself, the project involves construction of a dedicated railroad and port. This forms a modern, efficient, and integrated system. The project is embodied in a 50-50 association contract between International Colombia Resources (Intercor), a wholly-owned subsidiary of Exxon, and Carbocol, the Colombian state coal company. Intercor and Carbocol share investment and operating expenses equally. Intercor has the additional responsibility of managing operations on behalf of the partners. Each partner is entitled to 50% of the coal produced, and each markets its share separately. The project is a multi-seam, truck and shovel operation, based on large reserves (2 to 3 Gt or 2.2 to 3.3 billion st) of high quality bituminous coal. Exports began in the first quarter of 1985, at modest levels through what is called Early Coal Facilities. The permanent coal handling system began operation in February 1986. Production will increase rapidly in each of the next few years, reaching the design capacity of 15 Mt/a (16.5 million stpy) in 1989. Based on available resources, however, the resource will support expansion, and continued growth in production into the 1990s is feasible. Importance of transportation The success of a new coal export venture, such as Cerrejon, depends heavily on efficient transportation. In the international coal industry, overland and ocean transport can in some cases account for 40% to 50% of the final value of the product. Many coals, such as western US subbituminous coals, cannot reach export markets at all because of their low heat content and great distance from export markets. By the same token, low-grade resources are often commercially attractive for local markets even in the face of competition with much higher quality coals from distant sources. Figure 2 shows the growth in steam coal imports into Europe, the largest trading market. Through

Jan 6, 1986

By G. Luttrell

Coal preparation plants play an important role in modern society by providing high quality feeds for coal-fired utilities, industrial boilers and metallurgical coke facilities. Unfortunately, field data indicate that preparation plants are often not operated under optimum conditions, resulting in lower productivity and lost profits. In many cases, this shortcoming can be attributed to a failure by plant operators (i) to recognize the importance of correctly adjusting plant operating conditions to accommodate requirements dictated by coal sales agreements within different coal markets and (ii) to properly account for variations in product moisture with particle size across different plant circuits. This paper discusses the important influence of moisture constraints on preparation plant optimization and provides a case study to illustrate the potential gains that can be realized via proper understanding of plant moisture control.

Jan 1, 2009

By A. C. T. Bigg, Y. Kocak, N. K. Bodur

The Gumuskoy silver mine, owned by the Etibank, in the province of Kutahya, Turkey, has been operating since 1987 with primary, secondary and tertiary crushers, and two parallel single stage ball mill circuits. Continuing problems with crushing and feeding of the ore to the ball mills, because of the moisture retaining and sticky nature of the ore, prompted an investigation into the possibility of converting the grinding circuit to an autogenous or semiautogenous grinding circuit. This would remove the bottleneck associated with the secondary and tertiary crushing. At the same time the target feedrate is to be raised from 140 t/h to 175 t/h. This paper demonstrates the response of five ore types, and blends of ore types in an onsite pilot plant test program, and also suggests how the variations can be handled in a SAG mill/ball mill circuit incorporating just one of the present ball mills.

Jan 1, 2000

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By Minggao Qian, Jialin Xu, Wenqi Lai, Weibin Zhu

This article advances an innovative concept explaining the connotation and technical system of "green" mining. The important theoretical foundations of "green" mining are the distribution and development characteristics of joints, fractures and bed separations, and the seepage and flow behavior of methane and water in the broken rock strata following coal mining. The main focus of "green" mining technique includes water-preservation in mining areas, coal mining under buildings with bed separation spaces grouted to retard surface subsidence, partial extraction and backfill mining, simultaneous extraction of coal and coal-bed methane, coal roadway supporting and underground disposal of rock waste, underground coal gasification, etc.

Jan 1, 2005

By M. Fustic, A. H. Paul

The geology of the Muskeg River Oil Sands Mine is described to demonstrate how geologic modeling aided in resource evaluation and material characterization during the feasibility and construction stages. Bitumen is hosted in the clastic sediments of the Cretaceous McMurray Formation which is informally divided into members representing the fluvial, estuarine and marine environments of this transgressive sequence. Lithofacies mapping of drill core provides further detail to classify materials as resource type, for extraction suitability and for construction suitability. Geologic interpretation provides tools for the engineers to produce effective mine plans and for the operators to execute them during mine development.

Jan 1, 2002

By Kiseong Hyeong, Young-Tak Ko, Gee Soo Kong

"The benthic environmental impact experiment addresses environmental impacts at a specific site related to deep-sea mineral resource development. For such a purpose, since 2010 we have carried out essential environmental research at both the BIS and a preservation site. We have acquired several tens multi- or box core samples at 32 sites within the BIS especially between 2011 and 2013, aiming to examine the basic properties of surficial deep-sea sediment as the potential source for deep-water plumes.In this study, we present physical the properties such as water content, shear strength and also geochemical properties such as major elements, rare earth elements (REEs), heavy metal contents at the BIS. Such proxies vary distinctly according to the Facies association. The lithology of all core sediments in the BIS corresponds to both Association Ib (Unit I/Unit II) and Association IIIb (Unit I/Unit III) on the basis of the KORDI classification (KORDI, 2004); Unit I is watery mud and dark grayish brown (10YR4/2) to dark brown (10YR4/3). Unit II is highly bioturbated mud and brownish yellow (10YR6/6). Unit III is very dark brown (10YR3/2) to black (10YR2/1) mud. Physical properties of these sediment types show that Association Ib is distinct from Association IIIb. The vertical profile of water content changed more sharply in Association IIIb probably due to compaction; water contents varied from 230 to 300% in Association Ib and changed from 200 to 250% in Association IIIb. The vertical profiles of shear strength are also quite different between Associations; the profile curve in Association IIb is much more gentle due to bioturbation."

Sep 1, 2014

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012