Search Documents

By B. S. Xakalashe, M. I. Khama, Q. G. Reynolds

The carbonaceous reduction of manganese ore is an energy-intensive process that releases large amounts of pollutant gases. In an attempt to circumvent the greenhouse gas emissions, this research investigates hydrogen as an alternative reductant. The reduction of manganese ore with hydrogen results in the structural changes in the intermediate products, which might limit the diffusion of the reactant gases through the pores. Computational fluid dynamics (CFD) models capture the structural changes and predict the rate controlling mechanism and this is key in designing the prereduction reactors. The current work uses CFD models to predict the degree of reduction in a shaft furnace under hydrogen reducing conditions. Manganese ore is described as a collection of scalar and tensor fields such as thermal conductivity of the porous medium, density, and viscous resistance. The results indicate that advection contributes significantly towards the overall transport of hydrogen to the reaction sites. Porosity of the final product was found to be higher than porosity of the raw material.

Mar 4, 2025

By A. C. Lawrence

A new approach to the -study of human factors in stope productivity by A. C. LAWRENCE B. Econ., D. Com. (S.A.) (Member) The extent of the improvement in mean performance which could be achieved by reducing the variance between stoping gangs is examined, and it is shown that a worthwhile gain would result if variance were reduced by as little as 5 to 15 per cent. The problem of identifying human factors which contributed towards variance in gang performance was examined in one gold mine. A total of 342 'observations' on 49 stoping gangs were gathered, each observation consisting of a set of figures for 36 variables for one gang for one week. The variables included 'stope factors' such as face length, 'gang factors' such as the ethnic composition of the gang, and 'supervisory factors' such as the experience of the miner. These variables were related to 'tons trammed per week' as a measure of work performance. The findings showed that certain of the predictor variables accounted for 66 per cent of the variance in gang performance and about two thirds of this could be attributed to gang and supervisory factors, that is to the 'human factors'. The method suggests a basis for a new approach to the identification of human factors and is a promising step towards optimizing gang performance.

Written contribution by J.F. Curtist The paper is an interesting exercise in the application of mathematics to a theoretical situation presumed to oc¬cur underground. However, some of the assumptions on which the calculations are based are unlikely to occur in any actual mining situation. Assumptions made in the paper Objections to these assumptions are noted seriatim. (1) `it is assumed that any loading-rate effect will be small and can be ignored' (p. 3). A loading rate of the order of 50 kN-12 per cent of the maximum load-is customary to prevent the props being dislodged by the blast. (2) `it is unlikely that all the props will be installed with their full stroke available, but for the purpose of this analysis, it is assumed that this is the case' (p. 3). A more reasonable assumption would be that, with the most careful selection of prop length and the most rigid control of stope width, the available stroke length would on average be reduced by the order of 70 mm on installation-20 per cent of full stroke. (3) `each support unit supports a block of 3,3 m2 bound¬ed by vertical fractures with zero cohesion that are parallel and at right-angles to the stope face respec¬tively' (p. 5). Joughin and Jager have shown this to be an unwar¬ranted assumption in respect of the positioning, the direction, and the dip of the fractures present in a stope in rockburst conditions. If, as assumed, there was `zero cohesion' between such blocks, the removal of a hydraulic prop in row 3 supporting such a block would ensure that it fell out before a profile prop could be installed in the same position. (4) `the height of each of these blocks is 3,0 m, the volume of each block is 9,9M3, the mass of each block is 27 225 kg' (p. 5). The concept of individual props being affected by dis¬crete blocks of known and uniform dimensions of relatively low ground velocities (less than or equal to 2,16 m/s) acting in line with the axis of the prop is one that lends itself to neat mathematical calcula¬tions. It does not, however, bear much similarity to the actual conditions that are exposed underground in excavations where rockbursts occur. Ortlepp and co-workers concluded that `the impulse of the shockwave can cause the displacement of the

Jan 1, 1991

By L. A. Vermeulen

A simple argument shows that it is impossible for the flight of a rod in contact with a litter bar in a rotary mill to be initiated at that point on the upside of mill rotation when all the forces acting on the rod are in equilibrium. The argument was confirmed experimentally in a study showing that the lift of litter bars is a function of their height, that the rod velocity at the point of departure has a significant radial component, and that the subsequent flight of a rod is along a parabolic trajectory as predicted by elementary mechanics. A quantitative account of the observed effects, which is based on a dynamic theory of the sliding interaction between rods and litter bars, revealed interesting properties of the motions of rods down the surfaces of litter bars when the latter are in uniform circular motion during the rotation of a mill.

Jan 1, 1985

This paper presents a quantitative approach to the problem of determining design capacity and field dimensions of underground coal mines using room- and-pillar mining systems. In evaluating these design variables, relationships among mining costs, number of production sections in mines, location of central shafts, mine field dimensions, section production, mine output, and cost of production losses due to underground man-traveling are analyzed. Thereby the unit cost of coal is expressed as a function of the design variables as well as input parameters such as seam angle, seam thickness, seam depth, underground traveling speed of men, mine recovery and plant recovery. The problem is then formulated as a nonlinear optimization model in terms of minimizing the unit cost of coal subject to a set of constraints and solved analytically for flat seams and numerically for inclined seams. Sensitivity analysis of the variables is also included in the paper.

Jan 1, 1987

By E. Schoeman

Ion exchange resins were investigated for the effective recovery of platinum, palladium, and gold from a pregnant cyanide heap leach solution. Screening results indicated that strong-base anion exchange resins proved to be most effective in the recovery of these metal cyanides. Gold was selectively recovered with the use of Minix, while effective recovery of gold, platinum, and palladium over the base metals, copper, and iron, was achieved with Amberlite PWA-5. Successful elution of these metal cyanides was possible from both Minix and Amberlite PWA-5, using a 2M potassium thiocyanate solution at ambient temperature. Acidic thiourea was unable to elute platinum from either Minix or Amberlite PWA-5. Effective elution of palladium and gold were, however, achieved with use of acidic thiourea. Using these results, two conceptual flow diagrams for the recovery of these metals from cyanide solutions are proposed.

Jan 1, 2012

OFS Branch Committee Meeting held in the Committee Room at the Welkom Club at 4.15 p.m. on Wednesday, 5th March, 1975. Progress in mineral dressing The National Institute for Metallurgy and the South African Institute of Mining and Metallurgy are to hold a symposium on 17th and 18th September, 1975, entitled 'Recent Progress in Mineral Dressing'. INFACON 74 This book of over 300 pages is a record of the First International Ferro-alloys Congress, which was held in Johannesburg from 22nd to 26th April, 1974, under the auspices of the Ferro Alloy Producers' Association of South Africa, the National Institute for Metallurgy, and the South African Institute of Mining and Metallurgy. NIM reports Report no. 1595 Preliminary tests on low-grade brecciated fluorspar ore from the Ottoshoop district. (5th Nov., 1973, declassified April 1975). Report no. 1612 Flotation tests on sulphide-bearing high-grade brecciated and wad ores. (20th Mar., 1974, declasl>ified April 1975). Report no. 1643 Further tests on low-grade brecciated fluorspar ore from the Ottoshoop district. (12th Jul., 1974, declassified April 1975). Report no. 1654 The determination of osmium in platiniferous media. Report no. 1689 The determination, by atomicabsorption spectrophotometry, of arsenic, selenium, tellurium, antimony, and bismuth on ion-exchange restns. Report no. 1715 Flotation tests on various types of ore from the Ottoshoop district Report no. 1730 The chromitite from the Marico occurrence, western Transvaal, its alteration, and possible reasons for its refractory nature. Report no. 233 A chemical and mineralogical study of microlite from the N oumas pegmatite. 24th Geomechanics Colloquy The above Colloquy is to be held on 2nd and 3rd October, 1975, in the Salzburg Congress Hall. Rosenhain centenary The centenary of the birth of WaIter Rosenhain (1875-1934) will be celebrated by an international conference to consider how physical metallurgy has contributed to engineering practice. Iron and steelmaking The Centre de Recherches Metallurgiques (CRM) and the Verein Deutscher Eisenhiittenleute (VDEh) are jointly to hold the International Meeting on Iron and Steelmaking 1976 in Brussels from 17th to 18th May and in Diisseldorf from 20th to 21st May, 1976. International Symposium on Mine Surveying The III I.S.M. is being held in Leoben, Austria, from 28th June to 3rd July, 1976. Book review Tenth International Mineral Processing Congress. 1973. London, The Institution of Mining and Metallurgy. 1208 pp. £20. Particles A course on particle characterization and a symposium on experience in the applications of particlesize analysis will be held during the last week of July in Pretoria and Johannesburg. A.S. & T.S. Trust The A.S. & T.S. Trust was formed on 24th March, 1972, to mark the Golden Jubilee year ofthe Associated Scientific and Technical Societies, with the object of advancing science and technology in South Africa. Second International Congress of Engineering Geology The Proceedings of the above Congress, which was held in Sao Paulo, Brazil, from 18th to 24th August, 1974, are now available.

Jan 6, 1975

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

By W. Soetaert, P. Dhar, H. R. Kota, M. Thornhill, S. Roelants, I. V. Chernyshova

Yeast-derived bola-amphiphiles have attracted considerable attention for their applications in various industrial sectors in recent years. However, only a few studies on this class of surfactant were reported to be relevant to mineral processing applications. In this paper, one of the novel surfactants, acidic glucolipid obtained from Candida bombicola sophorolipids and modified by using Penicillium decumbens naringinase substrate has been evaluated for its interaction with chalcocite and calcite minerals because of a new Cu-ore Nussir deposit in Norway containing calcite impurity. The interaction of glucolipid biosurfactant with copper sulphide and carbonate minerals was investigated with zeta potential, adsorption and FTIR studies, and also by Hallimond tube and bench scale flotation tests using pure minerals and Nussir copper ore, respectively. The results illustrate collector adsorption and flotation of copper sulfides at neutral pH. The bench-scale flotation results demonstrate that copper sulphides can be selectively floated from carbonate and silicate gangue minerals. This study underlines the glycolipid’s high potential for its use as collector for flotation of valuable copper sulphide minerals. Keywords: Flotation, biosurfactants, adsorption

Jan 1, 2020

By S. V. Mkhatshwa

The purpose of the study was to investigate the factors which affect the performance of the loading and hauling fleet and also find possible solutions to eliminate these factors, so that the daily tonnages required could be produced .This is due to the high demand of manganese required by clients. The investigation strongly focuses on the performances of the three 777D Caterpillar trucks and the R984 C Liebherr Litronic Hydraulic Excavator. In the content of the study, these machines are used to remove and move the low grade manganese (also known as the top cut overburden) in order to expose the high grade manganese from north pit to dump 4. The objectives of the project were to determine the actual performance of the loading and hauling fleet per shift, compare the actual and the theoretical performance and identify areas that need to be improved. To achieve the goals set for the project, a number of activities were carried out. ?Perform a time study to compare the performance of the loading and hauling fleet with the manufacturer specifications ?Match the equipments analysis for Loading and hauling ?Road conditions analysis ?Rolling resistance and Road Gradients analysis ?Operating cost analysis.

Jan 1, 2009

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Safety and health can be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard is called AziSA, which means ?to inform? in isiZulu. AziSA provides an architecture that allows for connection of any type of sensor and that is particularly suited to wireless sensing. On the safety side, the CSIR is developing a suite of sensors specifically around the risk of rockfalls. Sensors such as an electronic replacement for the barring tool, or a thermal sensor that can detect loose rock, can already be used to identify potential hazards in the hangingwall. When these sensors are combined with location and time information in a single database, it becomes possible to build maps of risk and to extrapolate risk into unmined areas. It is also easy to confirm that routine safety procedures like barring are actually taking place. In the future, it is proposed that entry inspections will be made using remote techniques that will not place an individual miner at risk. While miners will still be required to bar or place support, they will do so with a clear idea of which portions of the hangingwall are safe, and which present risk. On the health side, if a network such as AziSA is deployed in the stope, it becomes much easier to monitor the condition of individual miners. The work strain experienced by miners can be monitored through heart-rate sensors, and their core body temperature can be monitored using various novel techniques discussed in the paper. Additional sensors can be added to quantify worker exposure to hazards such as noise or dust. Individual sensors allow for people who are at an unacceptably high risk of developing heat disorders to be treated timeously, and they also allow for team management based on objective measures. Over a longer period, position sensing and environment monitors, or personal dosimetry, provide a powerful management tool to prevent workers from being overexposed to hazards, and to confirm that management instructions are being followed. Cost-effective sensing in the stope is a major challenge, but one that can be overcome through technology like that used in AziSA. Sensing provides opportunities both to make immediate interventions when workers are exposed to unacceptable risk, and to manage the long-term exposure of workers to hazard.

Jan 1, 2010

Good blasting practices based on the careful application of explosive energy lead to significantly safer mining operations. Case studies demonstrate how the selection of the correct charge mass, explosive type and round design are vital for extracting the exact amount of rock required and preventing spurious damage to the remaining rock mass. In other cases the explosives are applied to precondition the rock mass, design rockburst resistant support, prevent damage to important excavations and reduce the exposure of miners to unsafe conditions. The Hybrid Stress Blasting Model is used to understand the explosive rock interaction and to illustrate and contrast good and bad blasting practices. In all cases, good supervision is required to continue safe mining according to the design. Keywords Blasting, safety, production, preconditioning, explosives, numerical modelling, drop raising, vibrations, and presplitting.

Jan 1, 2011

By C. C. Pretorius, S. Ramjee, R. J. Mostert

The study investigates the effect of prior corrosive exposure on crack growth resistance behaviour of thin sheet (3 mm thick) aluminium alloy 2024-T3 at slow strain rates. Compact tension specimens were exposed to standard corrosive environments that simulate accelerated atmospheric corrosion attack. Two corrosive environments were considered – an exfoliation corrosion (EXCO) solution and a 3.5 wt% sodium chloride solution. The unloading compliance R-curves of the two-hour EXCO-exposed specimens revealed a significant degradation of approximately 11% in the crack growth resistance behaviour (Kc_e values) compared to the baseline (air-exposed) values. Furthermore, secondary intergranular crack formation was also revealed in the plastic zone ahead of, and adjacent to, the crack tip of these specimens; which formed during the crack growth resistance loading. It is postulated that the observed degradation of the Kc_e values of the EXCO-exposed material is due to hydrogen embrittlement since the exposure times for the EXCO evaluation were limited to ensure that uniform corrosion dominated; that is, significant penetration of corrosion damage and pitting due to localized corrosive attack did not occur. The sodium chloride-exposed specimens revealed a similar degradation (13%) after 24 hours exposure. However, slight intergranular corrosive attack and isolated pitting were observed on the exposed surfaces prior to crack growth resistance loading, resulting in notch effects that could assist in crack growth. Pitting and intergranular corrosion were, however, not observed at the pre-crack tip. The relative contributions of the notch effects and the hydrogen embrittlement during the degradation of the KR performance are, therefore, unclear.

Apr 1, 2021

By J. H. Viljoen, A. Heyns, J. F. Morrison, C. H. Wyndham, N. B. Strydom

Discussion M. J. Martinson* (Associate Member): This is another interesting paper in the series which the Human Sciences Laboratory is publishing on the physiological cost of the more strenuous manual tasks performed underground. As a mining engineer-albeit presently an academic one -this contributor is more concerned with the practical significance of the study in the field of stope cleaning than with physiological niceties, but before discussing some of the practical issues raised by the paper perhaps the authors would care to reply to lay comment on three physiological matters. Firstly, in two places the authors make statements to the effect that the maximum oxygen intake of 'average' (sic) Bantu mine workers is 3.0 l/min. What do the authors mean by 'average'? Maximum oxygen intake in the individual is probably some function of inter alia age, physical fitness, state of health, ambient partial pressure of oxygen, diurnal and/or seasonal changes in metabolism, and possibly cumulative exposure to dust and other occupational contaminants. Since maximum oxygen intake is apparently such an important quality in manual labourers we ought to have a clear picture of its distribution in the entire labour force, and also know precisely how the individual's quantum is affected by factors such as those mentioned above. Secondly, arising out of the same statements and ignoring the reservation implicit in the previous paragraph, is it correct to say that the 'average' Bantu mine worker has a maximum intake of 3.0 l/min? In the August 1966 issue of the South African Journal of Science four of the present co-authors reported the mean maximum oxygen intake of a random sample of 338 Bantu recruits of different tribes to be 2.63 l/min with a standard deviation of 0.542 l/min, and these figures were repeated in a paper published in the November 1968 issue of this Journal. Admittedly the mean maximum oxygen intake of the six subjects used in the present study was 3.05 l/min, but since they were selected on the grounds of previous shovelling experience they can hardly be regarded as being 'average' recruits. Thirdly, it seems to me that the authors are perhaps a little uncritical in their acceptance of the '50 per cent of maximum oxygen intake' level of activity for endurance work. I am not unmindful of the evidence upon which this level is based, but I suggest that the evidence is at best tenuous and that the whole topic of fatigue and 'optimum' levels of productivity under conditions of high muscular activity and considerable psychological stress is a lot more complicated than would appear from the authors' ready acceptance of the 50 per cent level. Under present working conditions the question is largely rhetorical because it would need an army of supervisors to ensure that all members of a typical gang work at 'optimum' levels throughout the shift, but if individual performance should ever become more readily determinable the issue might become crucial to management and malayisha alike. So much for physiological matters; now a few random thoughts on some wider, practical issues raised by the paper. In the paragraph headed Material the statement is made that 'The mixture (of fine, medium-sized and bigger rocks) was considered to be representative of an average underground rock sample'. Elsewhere in the report the authors specifically draw attention to the effect of particle size on the oxygen consumption of men shovelling graded material, and intuitively one imagines that the size distribution of the material being shovelled would be highly significant in a study such as this. Presumably the authors were forced to assess size distribution subjectively because of the lack of objective data on the subject, and possibly the necessity for this assumption highlights how little we know quantitatively about any of the variables in stope cleaning systems. In this connection it may be remarked that although the present study was largely designed to show how dip and stoping width effect energy expenditure in shovelling, no data are given-nor, probably, are they available-to show how the industry's stoping tonnage is distributed in terms of these two factors. It seems to me that if the mining industry seriously hopes to improve stope productivity it must start by measuring the basic variables in existing systems. Elaborating somewhat on the previous paragraph, there also seems to be a tremendous gap between the present study-and its predecessors-and the prospect of gainfully using the information so carefully garnered by the authors. It would be reassuring to hear from the authors that their work on the physiological aspects is being integrated in some master plan for increasing productivity of manual labour. This I fear is not the case, and if productivity has changed at all in recent years I would hazard a guess that the change has been brought about by random factors rather than by systematic engineering design. The Human Sciences Laboratory has worked extensively in stopes in the past, and possibly the time has come when it should widen the ambit of its operations to include engineering-type analyses of cleaning systems, with particular emphasis on the economics of rapid cleaning by manual labour. Perhaps experiments could be conducted with stakhanovite-type gangs consisting of men selected for their high maximum oxygen intake and superior motivation; these men might be offered special incentives in the shape of extra pay

Jan 10, 1969

By E. Govender-Opitz, L. Lelia

The South African mining industry plays a significant role in the economy of the country. Nonetheless, the negative impacts on the environment continue to prevail. In regions where mining exists in proximity to communities, mining activities have led to the disruption of modality. Rural communities are mostly affected as they depend on land use for agriculture to sustain their livelihoods. The conversion of land for mining activities often leaves the communities vulnerable when mines close because of the limited life span of mines. An ongoing discourse focuses on how the mining industry can contribute to sustainable development of the communities in which they operate. Post-mining transformation offers an approach for the mining companies to contribute to sustainable livelihoods post-mine closure by strengthening rural-urban linkages, which ensures inclusive development of both rural and urban areas. The paper employs a case study approach to Richards Bay Minerals and the adjacent rural communities of Sokhulu and Mbonambi. It sets out to understand the post-mining transformation employed by RBM and explore the rural-urban linkages that manifest as a result. Findings show that sand dune rehabilitation employed by RBM is successful in restoring soil fertility and establishing the natural ecosystem. The casuarina planted to rehabilitate the dunes is used to spur an alternative charcoal industry post-closure. The main rural-urban linkages that manifest are flows of people due to job opportunities and flows of goods from the sale of charcoal produced. However, there is a lack of communication and lack of authority to ensure responsible management of the casuarina plantation and equitable sharing of benefits. The paper recommends that other post-mining transformation strategies such as eco-tourism should be explored and that the government, at both national and local level, the community and the mine should be involved to ensure overall success and sustainability of the strategy. Keywords Post-mining transformation, rural-urban linkages, alternative land use

Jan 1, 2020

By R. Dehghan, M. Zarei, A. Tohry, S. C. Chelgani

Typical depressants for selective reverse flotation of iron oxides from complex silicates do not generally show high levels of efficiency. Therefore, as a hot topic, there are several ongoing investigations in this area. The main aim of this paper is exploring the potential of using humic acid (HA) as a depressant in reverse cationic flotation of hematite from complex silicates. For such a process, the wettability and flotation behaviour of pure minerals (hematite and silicates) was investigated at pH 10 in the presence of HA and cationic collector. Adsorption mechanism of HA on these minerals was measured by zeta-potential and FTIR. Results of flotation tests showed that at the lower concentrations of HA, selective separation of silicates from hematite is beneficial, where the floatability of amphibole was higher than pyroxene. A higher separation efficiency of hematite through reverse flotation was observed in the presence of amphibole, in comparison with the presence of pyroxene. Wettability studies showed that HA has a significant effect on reducing the hydrophobicity of treated minerals with the collector. The adsorption, ZPC and FTIR test results indicated that HA was adsorbed on both silicates and hematite. However, the absorption intensity onto hematite was much higher than silicates. It was found that the adsorption mechanism of HA on hematite takes place through both strong H-bonding and ligand exchange. Keywords: Reverse cationic flotation, humic acid, iron oxide, complex silicates, surface adsorption

Jan 1, 2020

By L. Dison

There are many potential uses in gold mining for an initially stiff element of backfill that will yield at a predetermined load and maintain that load to beyond a compression of 30%. Such elements could be used as yielding rib pillars, as replacements for more conventional supporting packs, as con- fining bulkheads for mass backfill, as supports to provide lateral constraint, and load-carrying augmentation to overloaded rock pillars. The paper describes a system of reinforced cemented backfill that can be used to provide the above requirements. The necessary characteristics of the reinforcing and the cemented tailings are described together with the method of design to obtain a predetermined stiffness and yield load. The load-compression characteristics of the reinforced tailings elements are described and the effect of changing various of the design parameters is demonstrated.

Jan 1, 1988

Broken Hill Mines-1968, edited by M. Radmanovich and J. T. Woodcock, published by The Australian Institute of Mining and Metallurgy, Melbourne, 613 pages. Price $A15. This volume, containing some 65 technical papers, was produced for the 1968 annual conference of the Australasian Institute held at Broken Hill to mark the 75th Anniversary of that Institute, founded at Broken Hill in 1893. That conference also coincided with the 85th Anniversary of the discovery of the Broken Hill mining field. This closely reflects the position in this country, where the Witwatersrand gold fields were discovered in 1886, and our South African Institute of Mining and Metallurgy will in March, 1969 be celebrating the 75th Anniversary of the founding of the forerunners of our Institute. There is a comprehensive report of the geology of the Broken Hill area and the mineralogy of the ore body, and there are reports on the mining methods and the metallurgical procedures which have been developed over 85 years of operation of one of the great mining fields of the world. The value of most of the papers is enhanced by a large number of illustrations and photographs. An early section covers the academic and practical aspects of rock mechanics, prospecting, and exploration techniques are described in some detail. A third of the volume is devoted to mining, with papers on 26 aspects. The breadth of the coverage gives an indication of much specialized development, research, and consequent maturity in all departments. The detailed treatment of metallurgical aspects such as sizings of individual mineral particles throughout the milling stages and the development of an on-stream analysis system for lead will commend this volume to the specialist. The committee responsible for the production of this volume, which brings together much information previously only to be found after searching through numerous publications, are to be congratulated on a well produced comprehensive review of many aspects of the mining and metallurgical fields. H.B.

1. New books Extractionmetallurgy'81. London, Institution of Mining and Metallurgy, 1981. 441 pp. $40. Structures and properties of engineering alloys, by W. F. Smith. London, McGraw-Hill, 1981. 512 pp. R89,65. Rock and mineral analysis, by W. M. Johnson and J. A. Maxwell (editors). 2nd ed. New York, Wiley, 1981. 424 pp. $40. Mining methods and equipment, by Mining Information Services. London, McGraw-Hill, 1981. 218 pp. International directory of acronyms in library, information and computer sciences, by P. M. Vaillancourt. New York, Bowker Publishing Co., 1980.516 pp. 2. New journals Trends in analytical chemistry (TRAC), Amsterdam, Elsevier, 12 issues per year. Subs. for Volume I (16 issues) D.H 95.50. Engineering management international, Amsterdam, Elsevier, 4 issues per year. V.S. $32.50, D.H. 70.00. 3. Mineral policy sector publications Mineral Bulletin MR 188. Vanadium: an imported mineral commodity. $3.60. Mineral Bulletin MR 190. Canadian mines: 1980 perspective. $3.00. Canadian mineral survey 1980, by the staff of Mineral Policy and Energy Sectors. $1.00. 4. NIM reports Report 2090 Observations made during the dig-out of a 48 MV A ferrochromium furnace. Report 2110 The investigation of a fracture on one side of a skip bridle in a mine shaft. Report 2111 Pilot-plant tests for the recovery of chromite and the noble metals from the UG-2 Reef at Maandagshoek. Report 2112 The behaviour of UG-2 chromite concentrates during smeUing. Report 2113 M uUivariable control of a milling circuit at East Driefontein Gold Mine. Report 2115 Estimation of material variation in powdered materials Report 2116 Optimum operation of a direct-reading spectrometer with excitation by a 5 kW inductively coupled plasma torch. Report 2121 Five robust indicators of central value. Report 2124 The direct determination, by differential pulse anodicstripping voUammetry at the thin mercury-film electrode,of cadmium, lead, and copper. Report 2127 The preparation of a reference material of South African zirconium concentrate from Richards Bay. Report 2128 The determination, by differential pulse anodic-stripping voltammetry at the thin mercury-film electrode, of cadmium and thallium in six NIMROC reference materials Report 2130 The organizing of conferences. Research grant The Board of Directors of International Precious Metals Institute in conjunction with Gemini Industries, Inc., a California-based refiner of precious metals, recently announced a Gemini Research Grant of $3000 will be awarded annually to a graduate student who is pursuing studies in metallurgy, chemical processes as it pertains to precious metals, or materials sciences, and who is performing or planning research studies in the precious metals. Accidents and diseases The Third International Colloquium for the Prevention of Occupational Accidents and Diseases in the Iron and Metal Industry is to be held on 15th and 16th June, 1982, in Palma de Mallorca, Spain.

Jan 1, 1981

By D. F. Malan, L. Scheepers

Seismic risk in the deep gold mines of South Africa has been studied for many decades. A clear understanding of the effect of geotechnical conditions on the seismic hazard nevertheless remains elusive. Certain reef types seem to be associated with a higher risk of rockbursts. The stability and deformation behaviour of excavations on the different reef horizons are affected by the rock types and the varying strength properties. The seismic response to mining is therefore also expected to differ according to the geotechnical conditions. As a case study of this behaviour, the seismicity at Mponeng mine was investigated. On the VCR (Ventersdorp Contact Reef) horizon, two areas can be delineated. On the eastern side of the mine, the footwall is shale, and on the western side it is a strong brittle quartzite. More large-magnitude events occur in the area with the shale footwall than the area with the quartzite footwall. Moment tensor analyses indicated that the majority of the large-magnitude events are not related to geological structures, but are face-related, implying that shear failure of intact rock is occurring ahead of the mining front. Preliminary modelling indicated that the closure volume for the shale footwall may be higher than that for the quartzite footwall, providing a possible explanation for the observed difference in seismic response.

Mar 2, 2022