Search Documents

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By John Floyd, Maria Rocha, Benjamin Cebrian

Wall control blasting is needed in most metal mining operations in terms of increasing mineral reserves and assuring the safety of the operation. This type of blasting has the goal to achieve a clean, stable rock wall in the shortest distance from a well fragmented, easy to excavate, blasted rock mass. This can be done with a variety of blasting techniques, all of which decrease the explosive energy towards the final wall. Each technique needs to suit the geology: modified production blasting, buffer blasting, pre-split and line drilling of empty holes. Pre-split is the most expensive technique, and allows final steeper bench face angles while modified production blasting is the least expensive but needs wider berms.

Jan 1, 2018

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera. The burning process of the aluminized emulsion explosive has been modelled with the ignition and growth (I&G) flow model in the LS-DYNA code. A routine based on the optimization program LS-OPT code was developed to identify the parameters in the burning rate function with the detonation velocities and the front curvature radii from two tests. A Perl code was implemented in the routine and was used to calculate the VoD, fit the detonation front and obtain the detonation front curvature radii. The calibrated parameters were used to predict the VoDs and the detonation front curvature radii for the rest cases. The results indicate that both the VoDs and the detonation front curvature radii from the numerical modelling are in good agreement with the experimental results. The numerical results also indicate that the variety of the burn fraction and the peak pressure with the change of charge diameters is reasonable with the calibrated parameters.

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera

Feb 1, 2020

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

In the March/April 2006 issue of the Journal, we published an ethical dilemma called “Blowing the Whistle.” We received many interesting responses to the article as requested. Some of the responses are printed here. We’ve also included “Blowing the Whistle” again in this issue as a refresher on page 37. Dear Editor, It is in my own personal belief that it would be extremely important if I were the blaster to take the following steps. 1. Hold an immediate emergency meeting with the contractor to convince them to stop work at this point.2. This meeting would need to be held with all powers that be in this construction company. This helps eliminate the hearsay (excluding the farmer). 3. Explain the entire situation to the contractors as it has been presented to the blaster by the farmer. 4. Recommend calling in an engineering or geological firm with the expertise to investigate this matter immediately, and take all immediate action based on findings. 5. Follow up with farmer allow him to speak, (a.k.a. vent) and assure him proper steps are being taken to come to resolve this matter. 6. Be a good listener, and communicator with the farmer while investigation is being conducted. 7. Should the contractor not want, or take any of these recommendations, the blaster himself and his company should question even working for this company ever again. This in itself would not be the class of people we would want to be associated with EVER.

Jan 1, 2007

By Charles Zdazinsky

Many blasting applications in the mining industry demand that the hard rock being blasted remains structurally competent. For example, pre-splitting is a common technique to reduce fracturing, and operators of dimension stone quarries use this blasting method to eliminate overbreak. When pre-split design parameters are not applied correctly, there will be a redistribution of stresses within the rock, resulting in Blast Induced Rock Damage (BID). Advances in geophysical technology are enabling blast technicians to monitor BID and then use the results to correctly design their blasts.

Jan 1, 2011

By Erik C. Nygaard

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small bore hole diameters the formation of high amounts of toxic fumes (CO, NO and NOz) can result. In underground blasting, problems can also occur with reduced visibility caused by uncombusted ammonium nitrate.

Jan 1, 1999

By Norman Disley, David B. Counter, Lionel Hebert

Misfires in underground and surface production blasts can be costly. Costs can arise from loss of resource, production interruptions, having to redrill or otherwise refire the blast (a hazardous process at best), due to added secondary blasting or breakage, and/or from increased LHD maintenance costs attributable to poor fragmentation.

Jan 1, 1996

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By P. Ross, O. Rielo, P. Katsabanis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. The paper reviews all available experimental information, ranging from small and medium scale tests in geologic materials to small scale tests at the laboratory and synthetic materials, simulating rock. Tests have been re-analyzed and discussed in terms of the information they present and the limitation of the testing environment in representing actual conditions. New results obtained from blasting experiments in specimens made of a grout have provided a clear picture of the effect of delay on fragmentation. The grout used has a strength of 60 MPa (8700 psi), density of 2.5 g/cm3 and P-wave velocity of 4000 m/s (13100 ft/s). Each block was placed in a yoke to eliminate unwanted reflections and the desired delay was obtained using the appropriate length of detonating cord between holes or sub-millisecond electronic detonators. Delays ranged from 0.1 ms/m (0.03 ms/ft) of burden to 16 ms/m (4.9 ms/ft) of burden. Fragmentation was obtained using screen analysis of the collected fragments. Delay time has been shown to be a significant parameter affecting fragmentation and back break. Generally larger fragments and less back break was observed at short values, while fragmentation somewhat deteriorated at significant delay times, compared to what was observed at intermediate delay times. The work is now extended to include the effect of energy partition on fragmentation as well as the effect of initiation point and coupling ratio.

Jan 1, 2014

By Donald J. Westmaas, Fred C. Drury

The factors affecting the selection and use of exploisves have changed radically in the past three decades. The objective of this paper is to point out considerations which should now be employed by the Explosives Engineer in his selection and use of modern chemical explosives.

Jan 1, 1978

By Franklin J. A, Tam C. Palangio, N H. Maerz

WipFrag systems I, II and III have become the world standard in photoanalysis systems to measure particle sizes. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved ~to allow automatic measurements of the size distribution of particles on moving conveyors, in truck boxesand on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can, be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes, which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1998

By Calvin Konya, Theodore R. Myers, Robert Lundquist

The design of a single, large mass blast using ring drilling may take two to three months. This time requirement inhibits the evaluation of multiple designs. It also reduces the flexibility to redesign a blast when a parameter affecting the blast changes. Manual preparation exposes the design of a ring blast to a greater probability of human error. The use of Computer Aided Design (CAD) can help to overcome the shortcomings of manual design preparation. High speed electronic calculation, as well as programming, allow for many designs to be considered before blasting. Parametric programming allows single or multiple parameter changes to be introduced into an existing design, such as changes in drilling equipment, variations in ore density or changes in explosive. Exposure to human error is reduced by programming that performs calculations and produces graphical displays for review by the designing engineer. The goal of achieving desirable fragmentation for the minimum cost, when using ring blasting, is obtainable using blasting design techniques and CAD. Multiple designs can quickly be generated and costed, producing cost curves that indicate an optimum design with respect to cost.

Jan 1, 1990

Prepare ATF Report of Theft or Loss (ATF Form 5400.5). A Report of Theft or Loss - Explosives Materials must be prepared when it is discovered that explosive materials are missing from inventory. Submit the original to the U.S. Bomb Data Center and keep a copy for your records. The form can be obtained from the ATF Distribution Center or from www.atf.gov. Although the U.S. Bomb Data Center should be notified as soon as possible, Federal law requires notification within 24 hours of the discovery. A full inventory check is also highly recommended (but not required) to locate missing explosives and to prevent future losses.

Jan 1, 2008

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By Paul McAnuff, Alastair Grogan

In Canada, the only vibration regulations which apply across the entire country are intended to protect fish spawning areas. The Provinces and Territories regulate mines and quarries, and are responsible for setting vibration and airblast regulations. Some Provinces have set specific regulations, while others leave these restrictions to the mines inspectors who can set limits on a case by case basis. For the most part, it is left to individual municipalities to regulate blast vibrations and airblast from other blasting activities, which differ from jurisdiction to jurisdiction, and in some cases are not enforced. Blasters working in different jurisdictions have to be aware of the applicable regulations for the area they are working.

Jan 1, 2005

By Theodore A. Christensen

Besides the moral responsibility for ensuring worker safety, today's blasting contractor has a major financial incentive for establishing an effective safety program: on-the-job accidents have a direct impact on a very sensitive cost area - Workers Compensation. Within specific parameters, a good safety program can reduce WC costs by lowering the Experience Modification Rate.

Jan 1, 1993

By Dae-Woo Kang, Sang-Wook Kim, Shin Lee

The Air-tubes blasting method is provided in which a series of aligned boreholes are charged with explosive s and air tubes in a predetermined blasting pattern. The air tube is composed of cylindrical flexible tubes which have a predetermined width and length to be fit with the site boreholes. Within a preferred formation, each borehole is charged with the explo sives and detonators with an air tube installed just above the explosives. Stemming materials are filled above the air tubes. At the limestone mine of Sung-Shin Cement Co., in South Korea, these blasting tests were performed by a diameter 102 millimeter and 15 m long boreholes with the charging length of explosives was 8m to 10 m by the total weight of explosive 40 to 50 kg with 3m to 6m air tube which has a 76 mm diameter, and 1m to 3m stemming cover. Blasting results showed the about 10% to 30% explosives savings available and especially, the about 20% to 50% reduction of ground vibration with the low noise measures around 2dB to 5dB by this new blasting method which was compared with the conventional blasting methods. The explosives and air tubes may be alternately charged along the boreholes. The use of air tubes which were charged above an explosive layer allow to form the quantitative air decking in every blast hole. Therefore, the Air-deck effect can be easily obtained through this blasting method, and also easy to increase the fragmentation rate resulting in the more suitable mucking procedures at the working site with the minimum usages of explosives for the better economic operations in mine quarries.

Jan 1, 2005

By Tyler Acorn, Tristan Worsey

A dozer operator at a surface gold mine accidentally drove a D10 off the side of a highwall. The blade of the dozer caught on the lip of a catch bench 60 ft. (18.3 m), down stopping its descent. The operator scrambled to safety in fear that the dozer would not hold.

Jan 1, 2014