Search Documents

By Matthew Graham, Tapan Goswami, Geoff Brent

In dragline coal mining operations, throw blasting is used for the controlled placement of overburden to maximise coal exposure rates or to minimise overburden removal costs. This may necessitate sacrificing thin coal seams, generally less than one metre in thickness, which are often present in proximity to the main coal seam. This represents not only a significant loss of potential revenue and profit but also a waste of a valuable energy resource.

Jan 1, 2010

By Manuel Villalobos Calderón

This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important drawbell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

Feb 1, 2020

By Timothy D. Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of negligence standard by a court of law, this paper illustrates the application of the negligence and strict tort liability frameworks using actual cases in which a decision was rendered. It is evident from these cases that some of the successful claims under the strict liability framework would not have been successful, and probably not litigated, under a negligence framework, which could result in substantial cost savings to the blasting industry and consumers.

Jan 1, 2004

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025

By Robert Hopler

In use, blasting powder is exploded by a spark from fuse, electric squib or miner’s squib, or by a primer of some high explosive, the last being employed only in heavy charges on open work. In mining, and sometimes in light charges on open work, blasting powder is made into cartridges by means of a paper tube or cylinder sealed at one end, which is known as the Du Pont tamping bag. Sometimes the paper cylinder is made by the miner by coiling a section of heavy paper, known as blasting paper, around a wooden pin, called a cartridge pin, and securing it with what is called blasting soap. The removal of the pin leaves a cylindrical cartridge open at one end, into which the powder is poured and the top folded and sealed with blasting soap.

Jan 1, 2014

By Maja Franjic, Ian Tolliday, Chris Collins, James Wiltshire

Ammonium Nitrate Emulsions (ANE) are a large segment of the explosives market for the mining industry. These emulsions are generally designed to be very stable but when breakdown does occur, removal of the resulting thick, crystallized material can be difficult, hazardous, time consuming and costly. A heavily crystallized emulsion cannot be pumped, so manual removal often becomes necessary. Buildup of semi-solid layers of crystallized emulsion can occur in bulk storage tanks or in truck compartments. In these situations, a manual cleanup involving hazardous confined-space entry and a significant amount of downtime is usually required. Once the crystallized emulsion is removed from the equipment, there is very expensive disposal of the resultant waste via a licensed trade-waste company. A much more desirable solution for dealing with waste emulsion is to completely break the emulsion, allowing the oxidizer and fuel phases to separate into two distinct layers. These layers would then be readily pumpable and could be disposed of much more economically. It may even be possible that the separated oxidizer phase could be repurposed as fertilizer and the fuel phase could be used to manufacture granular ANFO explosives. There are some existing products on the market for breaking emulsion explosives, but these generally need a high degree of mixing into the emulsion to achieve adequate breakdown. The aim of this study was to identify surfactants systems (demulsifiers) capable of effectively breaking a range of waste emulsions with minimized agitation. This paper describes the development and performance testing of novel demulsifier products. The test work involved a comprehensive series of laboratory screening tests, where the demulsifier formulations were optimized. A highly efficient formulation was identified, and field trials were conducted on real world, full-scale waste emulsions. Results will be presented that demonstrate a viable solution for the disposal, and potential re-use, of waste ANE in the explosives industry.

Jan 21, 2025

By Alan R. Gadberry

To resolve drilling and blasting problems, rather than treating symptoms and allowing problems to grow, the mine operator needs to change the way he operates. When a mine operator discovers a drilling and blasting result that he doesn't like, it is easy for him to think of that disappointing result as a problem. More often than not, however, that result is only a symptom of a problem, and the real, underlying problem cause can be seen when the operator looks in the mirror. Symptoms and problems relating to drilling and blasting are resolved when the mine operator makes appropriate changes in the way he manages his operations.

Jan 1, 1985

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By Hideaki Kitajima, Ryo Sakamoto, Katsuya Sasaki, Maehata Hidehiko

The Electric Discharge Impulse Crushing System (EDICS) is a technology for carrying out crushing by using electrical power and nitromethane. It is designed for construction tasks such as splitting of concrete and rocks.The EDICS consists of an electric discharge generator that supplies a high-voltage high-current pulse, a cartridge that generates power by using electric discharge energy, and cables that connect the electric discharge generator and the cartridge. The cartridge contains a thin metal wire that evaporates because of the electric discharge energy and a nitromethane that reacts with this evaporated metal wire. The cartridge can be used to generate a high pressure on the order of gigapascals within a time interval of several hundred microseconds, and crushing power equivalent to that generated by explosives is generated during this period. In recent years, the EDICS has been widely used in Japan because of its good performance and favorable characteristics.

Jan 1, 2011

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By William Reisz

The explosives and blasting industry has a commendable safety and security record, especially over the last several decades. This is due in large part to our newer technologies, better training and education, engineering practices, corporate initiatives, our professional organizations, and whether we like to admit it or not - our regulatory agencies.

Jan 1, 2012

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By Jesús V. Saccsa, Kenji B. Loayza, Erick M. Condori, Jorge A. Velásquez

This research investigates how to reduce manufacturing costs of a safety fuse composed of black powder, replacing its ingredient NO3K by NO3Na for processing, and contributing to minimize costs per blasting.

Jan 1, 2017

By Orica Peru, Pedro Lozada

Proper management of exclusion zones in blasting operations is essential to ensure safety without compromising operational efficiency. In Peru, mining regulations establish minimum exclusion distances specifically for personnel (500-meter radius / 1,640 feet), but do not define clear technical criteria for equipment. As a result, conservative distances such as 200 meters (656 feet) are often applied, negatively impacting productivity. This study proposes a technical-scientific methodology to reduce equipment exclusion zones, based on the use of advanced technologies such as drones, high-resolution cameras, and specialized software tools. The solutions used allow video recordings of blasts to be transformed into dynamic data through artificial intelligence and computer vision, as well as execute probabilistic simulations of the flyrock phenomenon using Monte Carlo algorithms and physical models calibrated to real operating conditions. Technological integration enabled the simulation of real operational scenarios, considering variations in critical blasting parameters that directly affect flyrock generation, such as drill diameter, explosive density, linear charge, and stemming height. Additionally, the Terrock methodology was incorporated, allowing the behavior of the rock mass to be included as a variable in risk assessment, improving analysis accuracy under different rock hardness conditions. The methodology was applied in four phases: diagnosis of the current design (15 blasts), modeling, validation of the calibrated model (6 blasts), and subsequent operational implementation. As a result, it was determined that the exclusion radius can be safely reduced from 656 to 492 feet (200 to 150 meters), maintaining as the main restriction the use of stemming lengths greater than 5.0 m. This optimization has the potential to generate tangible benefits, with estimated monthly savings exceeding USD 50,000, associated with reduced evacuation times, lower fuel consumption, less equipment wear, and increased productivity in drilling and hauling activities. The comprehensive approach presented here highlights the transformative potential of digital technologies applied to blast management, contributing to safer and more efficient mining operations.

Jan 26, 2026

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Lawrence Mirabelli, AngloGold Ashanti, Greg Gibson

Cripple Creek & Victor Gold Mining Company (CC&V) operates the largest surface gold mine operation in Colorado and is located west of Colorado Springs in Teller County between the towns of Cripple Creek and Victor. Gold was first discovered in the Cripple Creek mining district in the 1890s. CC&V has been conducting gold mining and precious metal extraction operations in the Cripple Creek Mining District since 1976. Current reserves are only amiable to surface mining since previous underground mining has depleted near surface ore rich veins.

Jan 1, 2014

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017