Search Documents

By S. M. H. Haddad, M. Saghaeian, R. Hejazi

"Due to limited water resources in mineral processing plants, increasing the efficiency of iron tailing dewatering system in order to obtain more usable water is very important. In this research, flocculation process, as one of the best method for water recovery, was investigated by using one organic cationic and three anionic types of flocculants with different dosages (10, 20, 30 g/ton) and iron ore tailing slurry (8 % w/w solidity) in series of graduated cylinders and obtained results were compared. it is observed that for tailing sample, the anionic flocculants have a significant effect on the settling rate of solid particles compared to the cationic types. Furthermore, effects of temperature (10, 23 and 43 ºC) and pH (2, 7 and 12) on the rate of settlement and turbidity was studied by utilizing the best flocculant. Findings showed that by increasing the amount of flocculant dosage, sedimentation rate went up and turbidity decreased. Comparison the out-put data of tests indicated that at temperature 23 °C and pH=7, the best results for both of faster settling rate and producing more clear water were reached. It should be considered that lower temperature has a more negative effect on the sedimentation rate and overflow water quality. So it will be predicted that for cold seasons, the consumption of the flocculant powder would be higher than the moderate or warm seasons. Also, coagulation/flocculation was evaluated by applying organic cationic coagulant added to anionic flocculant in three different times. Different ratios of coagulant to flocculant was examined (70%:30%, 50%:50%, 30%:70%) as well. Overall, utilizing coagulant had desirable influence on sedimentation experiments and obtaining high quality water. 1- INTRODUCTION In mineral Factories, among the important processes, solid-liquid separation process due to limited resources of water is very important and operates on iron ore tailing in settling tank as thickener in order to gain clear water for preventing water loss and applying again in plant units (Ciftci and Serhat Isik, 2017). Iron ore tailing include inharmonious compounds of iron oxides, silicates and aluminum-silicates. The percentage of solid in the tailing usually changes between 5 and 10 percent (Dash et al., 2011). One of the major problem about dewatering of tailing in thickener is solid-liquid separation of slurries with high stability because of fine particles. It means that rate of sedimentation is very slow and recovered water quality is inappropriate. This issue can be solved to a large extent by factors such as pH control, ionic strength and flocculation/coagulation process which results in aggregation of particles so that settlement by gravity is happened (Dash et al., 2011)."

Jan 1, 2018

By A. Qaredaqi, M. Mohammadi

Wet High Intensity Magnetic Separators, for short, WHIMS are used for recovery of Iron ores with low magnetic susceptibility. A Jones patent WHIMS with "grooved plates" matrix is being used in Dry Tailing processing line in Hematite Recovery Plant at Golgohar mining & Industrial Co. for recovery of Hematite. In this kind of separators Matrices are used for increasing the Magnetic field intensity and providing high magnetic field gradient. The laboratory WHIMS in Golgohar Iron Ore and Steel research Institute is capable to provide a background magnetic field strength up to 0.85 Tesla and in presence of ‚expanded metal? matrix, magnetic field intensity could increase up to 0.9 Tesla. More than 50% of feed particles in this separator were finer than 36 micron and recovery of these particles needs more magnetic field intensity. Hence, ‚Grooved Plates? matrices with Js= 2 Tesla and 3.8 mm gap were constructed. Measurements indicated that magnetic field intensity around the matrix will increase to 1.25 Tesla. Graph of Magnetic field intensity around the matrix to background magnetic field intensity was plotted and a model with Rsquare= 0.9 was offered. In addition, magnetic field gradient and magnetic force were calculated. In WHIMS with feed top size of 150 micron, the main effective forces on separation process are the magnetic force and the hydrodynamic drag force. With assuming that the particles are smooth and spherical and the flow is laminar, Recovery of fine magnetic particles is problematic in this separator because of drag force. Considering these facts and mentioned model, finest particles that are recoverable in different magnetic field intensities were calculated. Computations illustrated that with magnetic field intensity more than 0.8 Tesla, particles as fine as 4 micron are theoretically separable but it should be noted that in practice a larger attractable particle size would be expected.

Jan 1, 2014

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By C. R. Mambote

One of the processes developed for vanadium recovery from the fly ash of crude oil is through acid leaching. In the process, iron is one of the impurities that should be removed before vanadium precipitation, due to the fact that iron tends to co-precipitate with vanadium. The mechanism of iron precipitation is understood in terms of ferric hydrolysis, followed by the dimerization and subsequent polymerization of the crystalline iron compound. In order to develop a new approach for the fly ash processing, in the present paper the precipitation of iron from the liquor after the leaching process was studied with addition of NaOH or NH4OH in the presence of H2O2 or Na2C2O4 at 80°C. The objective was to investigate the feasibility of the selective precipitation which could be applied to vanadium and nickel recovery from the fly ash. The experimental results show the difficulties of removing iron by precipitation without co-precipitating nickel and vanadium.

Jan 1, 2014

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By S. S. Lu

In sodium oleate and salicylhydroxamic acid systems, sequence of floatability of three sulfate minerals is: barite>celestite>gypsum, in lauryl amine system is: gypsum>celestite>barite. XPS and infrared spectrum analysis are used to find that it is chemical reaction between sodium oleate and three minerals, physical adsorption on the surface of minerals for lauryl amine, and it is chelating reaction between salicylhydroxamic acid and three minerals possibly. Theoretical calculation on chemical bonds in crystal structures of three minerals is carried out, finding that breaking degree of Mn+?O2- in crystal structures of three sulfate minerals is closed related with floatability.

Jan 1, 2014

By B. H. Zhao

A low grade Pt-Pd ores, with 1g/t Pt and 0.13g/t Pd, and 8.70% Fe and 2.50% P2O5 is experimented to recover of Pt and Pd. The flowsheet is proposed which consists of Pt-Pd selective flotation, apatite flotation from tailings of Pt-Pd flotation, magnetic separation of magnetite from apatite flotation tailing. With butyl xanthate, N-ally group-O-isobuturyl-thioanimoformate and Sodium y-89 xanthate as collectors, sodium silicate as depressant, and sodium carbonate as pH regulator, a concentrate, assaying 324.52 g/t Pt and 45.62 g/t Pd, is obtained with recoveries of 87.23% Pt and 76.89% Pd from surface ore. A concentrate, assaying 1693.53 g/t Pt and 64.12 g/t Pd, is obtained with recoveries of 88.54% Pt and 83.78% Pd from primary ore. At same time, A iron concentrate assaying 64.12% Fe with a recovery of 24.94%, and a apatite concentrate assying 30.32% P2O5 with a recovery of 80.12% are obtained.

Jan 1, 2014

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By M. P. Krasteva

The froth flotation process for separation of mineral ores depends on the establishment of care-fully controlled froth. The formation of very stable froth in the flotation circuit is a problem that may occur in many plants, resulting in down-time, low quality and grade of final product and considerable expenses. Froths build up on the top surfaces of thickeners, tanks and flotation cells until they overflow, or until the efficiency of the circuit is impaired. A similar problem exists in Assarel concentrator, Assarel-Medet PLC, Bulgaria. Copper and copper-pyrite ores are dressed in Assarel concentrator. They are characterized with variable and complex mineral and physical composition. During the flotation cycle, resilient and difficult to break-down froth is formed, which subsequently impedes the process of thickening and clear overflow obtaining. Due to this problem continuous sampling in the cycle of thickening was conducted. The mineralogical, chemical composition, particle size distribution and solid phase content of the products were determined. It was established that the solid phase of the froth build up on the top surface of the thickener differs considerably from this one of the thickener underflow. The data clearly indicates that a separation process takes place on the top surface of the thickener ? fine particles of chalcopyrite are concentrated in the froth. The role of chemical reagent addition in the break-down of the flotation froth is investigated in terms of surface chemical phenomena involved in the stabilized froths. Measurements of the coper minerals wettability and surface tension at the air/liquid interface were performed. The surface active agent AERODRI® dewatering aids were laboratory tested. Bench-scale froth collapse tests were conducted. Reagent addition into pulp-froth system promotes and leads to a bubble coalescence, an improvement of the wetting of the mineral particles and a decrease of the surface tension at the air/liquid interface. The results of the laboratory experiments showed that the presence of the surface active agent leads to considerably decrease of the froth stability and the destruction of the deleterious froths build up on the top surface of the thickeners in Assarel concentrator.

Jan 1, 2014

By Robert Snow, Shibo Zheng, Wenyi Song, Xiaoqing Ma, Patrick Zhang

Numerous phosphate mineral depressants have been reported in the literature for use during anionic flotation of dolomite from carbonate fluorapatite in slightly acid circuits. In one part of this research, laboratory flotation experiments were conducted to compare the effectiveness of phosphate depressants to process ground, deslimed high-MgO Florida phosphate pebbles. Ten potential phosphate depressants were evaluated during laboratory anionic flotation of dolomite from phosphate in a slightly acid circuit using a sulfonated oleic acid soap plus oil as the dolomite collector. Eight of the depressants have been used by various investigators with foreign and domestic carbonate-phosphate ores. Four of the depressants were found to be reasonably effective during the current flotation study, namely: sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP), tetrasodium pyrophosphate (TSPP) and diphosphonic acid (DPA). Without depressants, the sulfonate collector required to produce cell underflow phosphate products containing <0.80% MgO and MgO/ P2O5 ratio <.033 was 1.13 kg/ton of flotation feed at a flotation pH range = 5.5-6.0. Using this collector level with 0.91 - 1.36 kg/ton of feed of STPP, SHMP or TSPP yielded phosphate products analyzing 0.73-0.92% MgO and MgO/ P2O5 ratios = .027-.034 at 90.0-96.8% P2O5 recovery. Similar grade phosphate products were obtained using DPA as the phosphate depressant at 84.1-87.5% P2O5 recovery. When no depressant was used, a similar grade phosphate product was obtained at only 65.9% P2O5 recovery. Another part of the research aimed at reducing MgO content in the final concentrate from Florida phosphate plants by conducting dolomite flotation on the final concentrate. Numerous phosphate depressants were tested for this purpose, including acidic, neutral and alkaline reagents. The most effective phosphate depressant was found to be phosphoric acid, giving both high grade and recovery.

Jan 1, 2014

By G. Alfano

We have investigated the breakage actions of solid particles observed in a new generation fluid energy micronizer being set up at our laboratories. The attention has been focussed in particular on breakage caused by interparticle collision, particle impact against a fixed surface, interparticle attrition and particle against wall of jet mill attrition. We have also studied the influence of grain size distribution, maximum particle size, flow rate and characteristics of the solid to be processed, as well as of flow rate and pressure of injected air on the above mechanism. Lastly, the operating parameters of a dynamic air classifier in closed circuit with the micronizer for recovering the fine fraction and automatically recycling the oversize, have been optimized. The findings of this investigation have been used to design, build and fine tune a micronizer capable of controlling the top size of a product having average particle size that meets market requirements for fine powders, while keeping power consumption relatively low.

Jan 1, 2014

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By Y. S. Li

The life cycle assessment method is applied to investigate the environmental impacts of cop-per-slag and copper-ore concentration process. Some environmental load data of copper production are obtained. The result indicates that damage level of human health, ecosystem quality and re-sources respectively is 0.174, 0.0203, 0.246 in the copper-slag concentration and 0.112, 0.0136, 0.299 in the copper-ore concentration. Environmental impact of copper-slag production (0.44) is more than that of copper-ore production (0.42), but can meet the environmental protect demand. With domestic copper concentrate supply gap enlarging, recovering copper from slag will lead to a significant improving of resource utilization and development of circulation economics.

Jan 1, 2014

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By B. Vasanthakumar

In this study, the effect of adaptation of B.subtilis to sphalerite and galena with respect to the selective flotation of sphalerite from the sphalerite-galena synthetic mixture has been examined. The changes in the surface charge of the mineral and the bacterium, cell wall components and the profiles of secreted proteins are discussed. The flotation recovery of galena increases with the increase in the adaptation cycle of B.subtilis to sphalerite and galena, while the flotation recovery of sphalerite is independent of the adaptation cycle with either mineral. From the gel electrophoresis analysis, the protein profile for the unadapted and adapted cells is found to differ distinctly and this may be attributed to varying molecular weight fractions arising from different growth conditions. Electrokinetic measurements showed shifts in the iso-electric points of not only B.subtilis but also of the chosen minerals after adaptation. Additionally, the zeta potential of B.subtilis is found to become less negative after bacterial adaptation to the chosen sulfide minerals, while it showed an increase in the magnitude of surface negative charge after various enzymatic treatments. The change in the surface morphology and cell wall components such as phosphate, uronic acid and acetylated sugars of the bacterial species during adaptation to sphalerite and galena has been assessed. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite can be preferentially floated from galena in the presence of the insoluble fraction of lysed B.subtilis cells initially adapted to sphalerite, with a high selectivity index. Keywords: bioflotation, b.subtilis, mineral adaptation, sphalerite, galena

Sep 1, 2012

By P. Romm

The German Kupferschiefer (copper shale) mining history reaches back over 800 years with its last active mines being shut down in 1990. Increasing metal demands and potential thread of future supply shortages led to the initiation of new exploration programs including feasibility studies for the Spremberg deposit as well as Federal Ministry of Education and Research (BMBF) funded research investigations of Kupferschiefer Waste Dump treatment in the Mansfelder region. This article describes the sensor based sorting results of coarse Kupferschiefer via Near Infrared (NIR) Sorting, being conducted by the department of mineral processing (AMR) in Aachen, Germany. It provides information about the necessity of presorting of the different ore types prior to flotation and puts the NIR Sorting results into context with conventional Kupferschiefer processing. Keywords: NIR sorting, kupferschiefer, sensor based sorting, preconcentration

Sep 1, 2012

By J. P. Dai

The Fankou Mine in Guangdong province, China, processes a polymetallic ore containing averagely 4.2% Pb, 8.5% Zn, and 90 g/t Ag. The main metal minerals including sphalerite, galena and pyrite are very finely disseminated and unevenly occurred in the ore, making it difficult to liberate them from each other. This paper presents the processing technology of the Fankou plant and the characteristic features of the novel technology applied.

Jan 1, 2014

By S. L. Zheng

The compound material of Nano-TiO2 Supported on the diatomite was prepared by the hydrolytic method with purified diatomite and TiCl4. The compound material was characterized by SEM, XRD, TEM, EDX, XPS, and the application test of the compound material was studied. The characterization test results showed that the Nano-TiO2 was coated on the surface of diatomite, the crystal of TiO2 is anatase, and the average crystal size is 12 nm. The pore diameter was reduced, but pore volume and surface area of the compound material are increased after Nano-TiO2 Supported on the diatomite. The application test results for treating coking waste water and formaldehyde gas show that the compound material of Nano-TiO2 / diatomite has adsorption and photo-catalytic function and strong degradation performance for phenol and formaldehyde.

Jan 1, 2014

By Amir Hajizadeh Omran, Mehdi Irannajad, Sima Mohammadnejad, Fardis Nakhaei

"This study presents an experimental program performed to investigate the effects of flotation variables including gas flow rate, froth depth, slurry solids percent, frother/collector dosage and pH on the froth bubble size during desulfurization of an iron ore. These conditions were varied using a central composite design (CCD). Image analysis techniques have been developed and used successfully to characterize the froth bubble size. Results of the CCD experiments showed that the flotation variables have different effects on the froth bubble size. The froth height, air flowrate, pH and solid content had the most important influence on the froth bubble size. The interaction between the collector-frother, pH-collector, frother-air flowrate, solid content-froth height, pH-froth height and solid content-pH were also significant. Process state can be accurately deduced from the froth surface appearance, providing a convenient way to quantify the parameters as a function of the process control. INTRODUCTION Flotation processes are subjected to a wide variety of process disturbances, some of which are made by the change in mineral features and others to variation in operating procedures. Feed and air flow rates, densities, size distributions and shapes of particles, surface properties, and reagent dosages and compositions can all change, often with significant effect on the performance of the plant (Moolman et al., 1996a). Flotation process efficiency is governed by the wettability of the solid as well as the surface tension at the liquid-gas. Both of these properties are influenced by operational conditions encountering in a flotation process. The structure of froths developed on the pulp surfaces of flotation cells has a remarkable effect on both the grade and recovery of minerals in the concentrate (Shean and Cilliers, 2011)."

Jan 1, 2018

By Vinay Jain, Dharmendr Kumar, Beena Rai, Venugopal Tammishetti

"Selective dispersion-flocculation is considered to be an effective process for the beneficiation of ultrafine particles. This process is based on the preferential adsorption of a flocculant on the mineral particles to be flocculated, leaving rest of the mineral suspended. It has been successfully implemented at plant scales for the beneficiation of ultrafine particles of iron ores, for which conventional methods such as gravity separation, magnetic separation and flotation do not work efficiently. However, the key element responsible for the success of any selective flocculation process is the appropriate choice of the flocculant used for achieving the desired selectivity. At our lab, we are working on design and development of such selective reagents for mineral processing applications, including the beneficiation of iron ore slimes, using a combined molecular modeling and experimental approach. In this study we have employed density functional theory (DFT) to calculate the interaction energies and explain the interaction mechanisms of chitosan with the main minerals present in iron ore slimes, namely, hematite [a-Fe2O3], goethite [a-FeO(OH)], gibbsite [a-Al(OH)3] and kaolinite [Al2Si2O5(OH)4]. The magnitudes of the computed interaction energies follow the trend: Hematite > Goethite > Gibbsite ~ Kaolinite Al-OH terminated > Kaolinite Si-O terminated Analysis of the optimized geometries and electronic structures reveals that the O & N atoms of chitosan molecule form coordinate bonds with surface Fe-atoms of hematite while only weak hydrogen bonds are formed in the case of goethite, gibbsite and kaolinite surfaces thus explaining reasons behind the stronger interactions with the hematite surface. The theoretical findings were validated by performing selective flocculation experiments using chitosan as a flocculant. The selective flocculation experimental results show that a final concentrate of ~60% Fe can be obtained from a feed containing 53.13% Fe with Fe recovery of 74%. The mineral estimation in the obtained concentrate indicated that hematite and goethite are recovered in concentrate while gibbsite and kaolinite are rejected in the tails. These observations were consistent with our theoretical findings. Our work highlights the promising role molecular modeling techniques such as DFT can play in the design and development of selective reagents for beneficiation of alumina-rich iron ore slimes."

Jan 1, 2018