Search Documents

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By Markus A. Reuter, Yongxiang Yang, Jim R. Post

In the upper part of an iron making blast furnace, sinter, coke and pellets are charged. While descending, the burden is heated and the iron oxides are reduced by the rising gases. The iron oxides start to soften and eventually melt. The melt and the remaining coke collect in the lower part of the blast furnace: the hearth. The remaining coke forms a porous bed: the dead man (see Figure 2). The melt flow through the dead man can affect substantially the hearth lining life, the furnace productivity and product (i.e. hot metal) quality. Physical characteristics like porosity and particle size distribution of the porous coke bed play a critical role. Because of the distributed nature of the coke properties, the bed packing structure and porosity will not be constant.

Jan 1, 2003

By M. Pelser, Lorenzen L.

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.A review of literature has proven that there is no conventional method for the control of calcium and or magnesium, although a number of potential processes have been identified. The technologies investigated included precipitation, ion exchange and solvent extraction, for which at least one method was found under each. To make the reader aware of these processes a short description was provided of each within the text.Of these processes, fluoride precipitation was selected for experimental investigation based on the low solubility of calcium and magnesium compared to the base metals. This process involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments were designed to investigate the equilibrium of the system at varying parameters of which the level of fluoride addition, the ratio of calcium to magnesium, and the identity of the soluble fluoride was reported. In all of the instances the process showed high selectivity towards calcium and magnesium over the base metals. The experiments proofed the process to have a higher affinity towards the removal of magnesium at compositions where the molar ratio of calcium to magnesium was higher than 1:3. It is often the case that the calcium to magnesium ratio is in the region of 1: 10. From this it follows that the fluoride addition has to be stoichiometric or greater for calcium and magnesium combined, if the calcium is to be precipitated. This was demonstrated as well. On the identity of the soluble fluoride hydrogen fluoride was compared to ammonium fluoride, of which the latter was found to be preferred."

Jan 1, 2003

By Lokesh K. Thakur, Peter Radziszewski

"For the cases tested (11 mills with 15 operating conditions), the Bond abrasion test steel media wear rate prediction gives an overall error of 73% and a standard deviation of 192.5%. However, total steel media wear in a given mill (ball or SAG) grinding process is a product of three recognised wear mechanisms -- impact, abrasion, and corrosion. A total media wear model can be defined on the assumption that the effect of each wear mechanism can be independently determined which allows for a total media wear model to be defined as the summation of the wear result of each mechanism (eqn. 1). It is assumed that impact and abrasive media wear is a function of the energy dissipated in impact and abrasion as estimated by a DEM charge motion simulation. Corrosive media wear is assumed to be a function of the media surface area present in a mill.The 3 initial tests developed (steel abrasion wheel, corrosion batch mill, impact chamber) coupled with the impact and abrasion energy spectra from a DEM charge motion simulation produced total steel wear rate results for the same cases as the Bond abrasion test giving an overall error of 0% and a standard deviation of 66.1%. However, if one were to consider the general observation that wear is proportional to energy and maintain the assumption that corrosion is proportional to media surface area then one would realize that the total media wear eqn. (1) can be reduced to eqn. (2). As this is a linear equation and one has, for the same mill, media wear and operating data for three different operating cases, one obtains three equations with three unknowns. This defines a simple matrix manipulation to determine the constants k1, k2 and k3. From the previous data set, we had 6 identical mills grinding the same ore but having different worn liner profiles and charge volume which provided the opportunity to average out the ki values over 20 combinations of 3 cases. With the determined ki values, it was possible to determine a second estimate of the contributions of impact, abrasion and corrosion to total media wear giving an overall error of 0% and a standard deviation of 56%."

Jan 1, 2003

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Chromite ore is an indispensable raw material in the manufacture of ferro-chrome and charge-chrome, which are used for the production of stainless and other alloy steels. The demand for chromite ore is ever increasing because of increasing consumption of these steels. Keeping this in view, Tata Steel is keen to recover values from fines and wastes, and also to produce value added products from their captive chromite mines and its processing plants.Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In many places, in India and abroad, mined non-marketable off-grade and low grade chromite ores are upgraded by using either simple classification techniques like screw classification, hydrosizing, hydrocycloning or conventional gravity concentration processes such as Heavy media separation, Jigging, Spiraling, Tabling etc.At Tata Steel, the ferruginous type ores are treated in Chrome Ore Beneficiation (COB) Plant that comprises: a crushing and grinding circuit; a classification circuit using hydrocyclones; and a beneficiation circuit using 4 stage spirals in the coarse circuit (-0.5+0.1 mm) and 3 stage spirals & tables in the fine circuit (-0.1+0.038 mm). In this process, 3 types of tailings are being generated and together analyses about 17 % Cr2O3, which is high. From the present operation the chromite recovery is around 70% and could not produce coarse concentrates (+0.5 mm size). Whereas the siliceous type ore is treated in the Lumpy Ore Processing (LOP) plant, consisting of crushing-washing & classification-hand sorting operations, to produce marketable grade lumpy ore and –10 mm de-slimed fines. These fines are intermittently treated in the COB plant. The higher silica content (greater than 1%) and low Cr/Fe ratio (less than 2.8) are the problems with these concentrates."

Jan 1, 2003

By Xiong Dahe

"SLon vertical ring and pulsating high gradient magnetic separator utilizes the combined force field of magnetism, pulsating fluid and gravity to beneficiate weakly magnetic minerals with the advantages of large beneficial ratio, high recovery, matrix not easy to be blocked and excellent performance.We have developed SLon-750; SLon-1000; SLon-1250; SLon-1500; SLon-1750 and SLon-2000 VP HGMS. Now more than 200 of them have been successfully applied in China.Application in Qi Dashan Mineral processing Plant of Anshan Iron and Steel Company: The iron ore consists of magnetite and hematite. In 2001, six SLon-1750 magnetic separators are applied to control the tails grade of fine hematite. The results of flowsheet is: feed grade 30.15%Fe, concentrate grade 67.00%Fe, iron recovery 75.86%. The results set up the historic high record of this plant and the processing coast is greatly reduced.Application in Gushan Iron Mine of Ma Anshan Iron and steel Company: There are 6 SLon-1750 and 4 SLon-1500 magnetic separators applied in this mine to treat refractory hematite ore. The feeding grade is about 45%Fe. The final iron concentrate grade is about 60%Fe and the iron recovery is about 76%. The results are much better than the previous gravity flowsheet.Application in Meishan Iron Mine of Shanghai Baoshan Iron and Steel Company: The mined ore consists of magnetite, hematite and siderite. Because of a relatively high content of phosphorus, the iron concentrate could not meet the market requirements. Now 18 SLon-1500 magnetic separators are applied to reduce phosphorus, which is reduced from about 0.4%P to 0.246%P. The quality of iron concentrate is greatly upgraded.Application in Panzhihua Ilmenite Processing Plant: In the past, the -0.045mm ilmenite fraction was discarded in to the tails because of lack of high efficient equipment. In 2001, the plant built up a magneticflotation flowsheet to recover the fine ilmenite from the -0.045mm fraction with 6 SLon-1500 magnetic separators. The total results are: feed grade 11%TiO2, concentrate grade=47% TiO2, recovery 44%. Each year the flowsheet recovers 60,000t fine ilmenite concentrate."

Jan 1, 2003

By Jan Svoboda, Atsushi Shibayama, Toyohisa Fujita, Toshio Miyazaki, Kenji Murata

"The electrical disintegration (ED) method and disintegration by underwater explosion were investigated as new fragmentation techniques for the kimberlite ore and tungsten scrap of superalloy (carbide bit). The results of various breakage tests demonstrated that both fragmentation methods as new disintegration techniques for recycling were able to liberate various components of materials of different resistivity and elastic impedance.SUMMARYThe breakage of the kimberlite ore from South Africa (sample size: 15 mm x 15 mm x 6 mm) was achieved by the ED method. A relationship between the sample size, voltage, the electrical current and the energy needed for the disintegration was found from the experimental results. Kimberlite exhibited a high degree of breakage, when the high voltage of 60 kV and the pulse current of approximately 5000 A were applied to the sample by the generator during 0.2 microseconds (Fig. 1)."

Jan 1, 2003

By Luís Marcelo Tavares, Juliana Segura

Comminution is one of the most energy consuming stages in a mineral processing plant. This consumption is not only related to the power supplied to equipment, but also to the indirect or embodied energy, mainly associated to materials that are worn during operation, including grinding media and liners. Until recently, preparation of iron ores in Brazil did not use comminution intensively, given that plants mainly produced sinter feed, natural pellet fines, besides lump ore. However, with decreasing ore grades, size reduction now occupies a centre stage in nearly all new plants. Technologies used up to date for processing low-grade iron ores in Brazil, in particular itabirites, have consisted of three or four stages of crushing followed by ball milling. A number of new plants are either being built or are currently being designed that will process the same type of ore, so that engineers are investigating alternative comminution routes. The paper analyses comparatively four comminution routes for processing a particular itabirite ore, many of which using technologies and layouts that have not yet been used in such application. Using data from bench scale and/or pilot-plant tests, the different routes are compared on the basis of sustainability principles in accordance to the Brazilian energy matrix, which is quite particular. It is concluded that if the sustainability criterion is used, then the optimal route would correspond to a circuit that uses HPGR technology with truncated feed followed by ball milling. Given the particular case of itabirite iron ores and specially to the one in the present work and the source of Brazilian energy, it is evident that indirect energy expenditure in comminution plays a significant role in greenhouse gas emissions when compared to direct energy, being the reason for the great attractiveness of HPGR technology. Evidently that these will have to be balanced against CAPEX, OPEX, NPV and other qualitative criteria, which can certainly lead to a different optimal circuit.

Jan 1, 2014

By Gülay Bulut, Ferihan Göktepe

Pyrite is the most abundant and widespread sulphide mineral and its flotation has been investigated by many researchers. It is well known that, pyrite is floatable under acidic conditions and recovery drops with increase in alkalinity due to changes in solubility of iron hydroxides on the pyrite surface. Most of the works also revealed out that pyrite displays variable behaviour in flotation circuits. This behaviour mainly related with origin and mineralogical composition of ore, liberation size, electrochemical behavior of minerals constituting ore, the trace and minor element content of the mineral, texture, application variables belonging to flotation circuits. In this study, copper activation effect was examined on different origin of pyrites. The experiments were performed with five high grade samples of pyrite from the different mining districts of Turkey. The pyrite samples were different from each other with respect to either their physical or chemical properties; they were different physical appearances and contained different associated minerals. In the micro-flotation tests, 1x10-4 mole/L copper sulphate and 1x10-4 potassium ethyl xanthate were used as flotation reagents. First of all pyrite samples were floated using only xanthate at different pH. Results showed that best floatation results obtained at acidic pH range for all pyrite samples. When copper ions were used to activate, all pyrite samples floated at neutral and basic pH values, too but depending on the samples, recovery and pH ranges were slightly changed.

Jan 1, 2014

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014

By Hajime Miki, Mutia Dewi Yuniati, Tsuyoshi Hirajima, Keiko Sasaki

Acid mine drainage is mainly due to pyrite/arsenopyrite oxidation processes, and suppressing such processes is important issue. As a promising process it is reported that silicate ion can complex with catechol (1,2-dihydroxybenzene) and this complex is oxidized to a solid silica layer on the surface of those sulphide minerals. Detailed behavior was investigated from the result of electrochemical experiments. Results of polarization potential showed that oxidation peak can be seen only in the presence of both silicate ion and catechol addition at this peak potential and this peak can be identified as silicate-catechol complex oxidation to silica. Potentiostatic experiments indicated the dissolution kinetics of pyrite. Untreated pyrite dissolution rates were higher than pyrite treated with catechol and silica solution. To enhance the silica layer reaction on pyrite, the pyrite potential was held at 550 mV vs. SHE in catechol silica solution. This pyrite dissolution kinetics was almost the same as untreated pyrite. Potential hold followed by drying for 30 min process resulted in much lower pyrite dissolution rates. Drying is important for development of the silica layer. Analysis of this potentiostatic curve provided a way to estimate the thickness of the produced silica layer and kinetic information of treated/untreated pyrite. Untreated pyrite showed thinner initial layer thickness on the surface of pyrite (oxidized passive layer, not silica) and higher oxidative kinetics of pyrite compared with silica-coated pyrite.

Jan 1, 2014

By S. A. Bogidaev, M. Yu. Tiunov

"The paper describes the results of the flotation tests with complex rare metal ores from deposits in the Trans-Baikal Territory. Correlations between the quality of produced wolframite, hubnerite and mica concentrates with or without the presence of various alkaline modifiers are determined. Commonly, rare metal ores contain minerals of comparable value to main elements recovered in processing plants using gravitational methods. The paper describes the results of flotation recovery of valuable minerals – main and associated – from gravity tailings of deposits in the Trans-Baikal Territory. It was found that gravity tailings from the first deposit contained fine-grained wolframite, mica (muscovite, lepidolite etc.), feldspar; hubnerite, scheelite, beryl, fluorite, rubidium-containing muscovite from the second deposit, correspondingly. This paper presents the results of the stage flotation tests with the production of tungsten (wolframite, hubnerite), fluorite and mica concentrates from gravity tailings. Figure 1 demonstrates the flowsheet of tungsten ore minerals and mica stage flotation from gravity tailings of the first deposit.Wolframite can be floated using oleic acid with the presence of soda ash, a complexing collector (IM-50), under slightly alkaline conditions in combination with a nonpolar collector [1, 2, 3, 4]. The study included wolframite flotation using the combination of two alkaline modifiers. Flotation of wolframite was performed after pulp desliming, using tall oil saponified with soda ash. The recovery of wolframite in the concentrate of rougher flotation reached 80-85%; the concentrate contained up to 1% of tungsten oxide that can be upgraded to a saleable product using gravitational methods. This procedure was tested during flotation of wolframite, tantalite-columbite and pyrochlore, and provided high performance regardless of a season, at pulp temperatures of 8-10°C, though fattyacid collectors are significantly inefficient at such low temperatures due to low solubility, dispersion and increased collector consumption, consequently. The introduction of two alkaline modifiers in pulp appears to improve these characteristics.The first stage of the tests was focused on increase of iron-bearing tungsten ore minerals recovery from gravity tailings and stabilization of the cold pulp flotation process."

Jan 1, 2018

By I. A. Podkamennyi, O. E. Kovalchuk, G. P. Dvoychenkova

"Using the methods of electron microscopy and IR spectroscopy, mineral components in the run-of-mine kimberlites and on the surface of diamonds were identified. The mechanism and sequence of mineral formation on the surface of diamond crystals were established. Systematization and classification thereof were undertaken for the first time ever.INTRODUCTION The high content of diamonds sized -5 mm in the kimberlite ores of Western Yakutia determines their processing depth in the size class 0.5 mm and finer [1, 2]. These diamonds are recovered by grease and froth separation based on the natural hydrophobic properties of the crystals. When refractory altered kimberlite ores are fed into the industrial process, the performance of grease and froth separation of the diamond ore greatly deteriorates. [4, 10, 15, 17]. Altered kimberlites are known to contain up to 90% of secondary minerals. This reduces by up to 40% the recovery of diamonds by grease and froth separation. [6].Diamond crystals from the grease and froth separation tailings were investigated. On the surface of the examined diamonds, hydrophilic mineral formations were identified, responsible for reduced recovery by physicochemical separation methods [3, 12, 18]. The aim of this study was to identify and describe the relationship between the composition of kimberlite ores and mineral formations on the surface of diamond crystals in order to systematize, classify, and then develop methods of removal in grease and froth separation processes. MATERIALS Following materials were examined in this study: - kimberlites of various material composition, - resulting slimes, - diamond crystals from kimberlite ore processing products."

Jan 1, 2018

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

By Vladimir Vigdergauz, Sergey Kondratiev

The paper reviews the existing criteria of the formation of particle-bubble aggregates during flotation. It is shown that predictions obtained by these criteria do not completely fit to the interaction between mineral particles and air bubbles. Experimental results of the studies into the influence exerted by molecular forms of collectors on the particle-bubble interaction are reported. Rate of dry spot expansion on the surface of pyrite with various combinations of chemically and physically adsorbed xanthate are examined. It is shown that molecular forms of collectors accelerate the rate of dry spot expansion on the mineral surface after the local rupture of the water film between particle and air bubble. The authors come to a conclusion that the molecular forms of collectors remove water from the interlayer between mineral particle and air bubble during their contact. Similarities of the proposed mechanism with the action of ion-molecular associates of fatty acids and amines are discussed. Reagents with high surface pressure and rate of spreading at the water-bubble interface are required for the effective interfacial dewatering. It is concluded that the value of surface pressure can serve as the criterion for efficiency of physically adsorbed reagents. The low surface pressure indicates weak collecting ability but high selectivity of the collector. Therefore, the presence of the molecular forms of collectors in the sorption layer is the necessary condition for formation of particle-bubble aggregates, and comparison of the surface tensions of collectors could be recommended as the estimation criterion of their flotation activity and selectivity.

Jan 1, 2014

By P. Somasundaran

Gangue minerals can often have severe adverse effects on selective value mineral separation. Such effects can be mediated through a variety of pathways or mechanisms. One popular mechanism is that of ?slime coating? or heterocoagulation, wherein the gangue mineral fines are believed to coat the value mineral surfaces and thereby reduce selectivity and floatability. Another pathway that has received relatively little attention is that mediated through the effect of gangue minerals on pulp rheology, and consequently selective separation. Our recent work in developing a scientific understanding of these effects has highlighted the prevalence and importance of this pathway. In this study, the impact of shape and morphology of serpentine gangue minerals on suspension rheology and selective Ni flotation from ultramafic ores was investigated. We found strong evidence for micro- and macro-network formation in the presence of acicular (needle-shaped) or fibrous minerals, which impacted pulp rheological properties. Results also supported the hypothesis that morphology has a greater role to play than mere shape. The size of the network ranged from 5 microns to 2 cm depending upon the amount and aspect ratio of fibrous minerals. These networks impede many flotation sub-processes, such as gas dispersion and bubble-particle interactions. Additionally, the small pore size of the networks prevents bubble penetration leading to a large transport of the gangue minerals to the concentrate via lifting of the entire network by bubble flux, which resulted in a significant grade dilution. Based on the scientific insights generated in this study various techniques have been developed to improve selective value mineral separation. Keywords: fibers, aspect ratio, microstructures, networks, pulp viscosity, gangue transport

Sep 1, 2012

By Yi-jun Cao, Jin-cai Ran, Guo-sheng Li, Jiong-tian Liu, Li-jun Deng, Shu-lei Li

A fly ash sample from a power station in Guangdong province has been characterized by size separation, X-ray diffraction, contact angle measurements and X-ray Fluorescence. The ash sample had a loss-on-ignition (LOI) (%) of 15.54% and a large proportion of the unburned carbon was distributed in the +74 µm and -20 µm fractions. Contact angle measurements suggested that the removal of unburned carbon from the fly ash using flotation would present some challenges. The effects of various operating variables on the removal rate of unburned carbon (RUC) (%) and (LOI) (%) were determined using a cyclonic-static micro bubble flotation column (FCSMC). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil (frother) dosage was 600 g/t, pulp density was 20%, superficial gas velocity was 1.4 cm/s and circulating pressure was 0.20Mpa. Column flotation tests indicated that the FCSMC method a viable and effective separation process for removing the unburned carbon from the fly ash. Under the optimized conditions, a clean ash with 2.13% LOI and 94.21% RUC was obtained.

Jan 1, 2014

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014