Search Documents

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By George Aristorenas, Carlos Englert, Jesús Gómez

"Laboratory test data of strain softening soils exhibit the development of a maximum (peak) shear strength followed by a decrease in the strength with continued straining. The rate of strength loss decreases such that an asymptotic minimum value, known as the residual strength, is approached. This paper presents an investigation of the evolution of strength degradation in excavation supported soils that exhibit strain softening behavior. The paper presents a numerical investigation of excavation support of slicken-sided clay, and results of shear testing on materials with similar strain softening behavior. A strain softening constitutive law is presented that can be used with the finite element computer software Plaxis for analysis of excavation support. A typical design section of a deep excavation support in stiff, fissured clay is presented that illustrates the limitations and conservatism of the residual strength approach for excavation support design. Finally, a discussion is presented on the impact of stiffer walls such as diaphragm walls, compared to less stiff systems such as sheet piles, on the design parameters.INTRODUCTIONIn the Washington, D.C. metropolitan area, the Potomac Formation is generally composed of stiff, fissured clays. Geotechnical engineers often associate the presence of slicken-sided planes within the formation as evidence that the soil cannot develop its peak strength. Although it is unclear how old and continuous these slicken-sided planes are, their occurrence, persistence and orientation appear to be somewhat random. Due to this uncertainty, the design of open cut slopes in these materials is often conservatively performed assuming residual shear strength values. This design approach may be justified for long-term open cuts when there is limited amount of geotechnical information and in view of back stability analyses of past slope failures. Furthermore, the lack of confinement in open cuts allows relatively high shear strains near the surface and toe throughout their existence, which promote mobilization of post-peak strength values and the ensuing progressive failure. Indeed, such behavior has been discussed in the past (Skempton, 1970; Schnabel et. al., 1982; Derrenbacher, 1998). A thorough study by Mesri et. al. (2003) of numerous slope failures concludes that the lower bound strength for stability analysis of non-failed slopes is the fully softened strength, which is intermediate between the peak and residual strengths, but that part of the slip surface may be in a residual condition prior to failure."

Jan 1, 2015

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By Joseph A. Sopko

There has been a trend in recent years in performing the initial formation freezing using liquid nitrogen (LIN) and then converting the system to circulating refrigerated brine. While proponents of this method state it decreases freezing time, it can also be considered an alternative to inadequate refrigeration capacity. This method was used on several small projects in the 1980s. Problems such as broken pipes, frozen brine, and unsafe work conditions caused contractors to re-think the method. This paper discusses these problems and also presents work schedules showing no schedule reduction. In fact, this method can lead to longer time as well as significantly higher costs. BACKGROUND Ground freezing as a method to provide groundwater control and temporary earth support for excavations is completed using a relatively simple process: drilling and installing refrigeration pipes around the perimeter of the excavation and introducing a coolant into these pipes. The coolant extracts heat from the ground, converting the pore water to ice and forming a strong, impermeable material. A typical ground freezing system is illustrated in Fig. 1. SYSTEMS There are two basic types of coolant systems: circulating and direct expansion. The circulating coolant system is made of two separate, closed systems. The medium circulating is the secondary coolant. It is cooled at a central refrigeration plant, circulated through the pipes, and warms as it extracts heat from the ground. It then circulates back to the plant where it is cooled. This coolant is chilled in a heat exchanger by the primary refrigeration system where a compressor system is charged with a refrigeration gas. The heat is ultimately extracted from the ground and expelled into the atmosphere by an evaporative condenser. Secondary coolants are usually a brine or glycol chemical while the primary refrigeration gas is anhydrous ammonia or another commercially available gas.

Jan 1, 2019

By Stephen Buttling, Zhong Rui

"A single unit gas fired power station was being built on the edge of the Gulf of Thailand in 2001. The soil conditions consisted of very soft to soft Holocene Marine Clay, and the site was part of a coast line which had been subsiding below high water mark for some time. In order to provide access around the power station a road system in a figure-of-eight formation was required, and this also needed to be above the design flood level, allowing for future settlement. A ground improvement scheme was proposed and constructed, which consisted of two spacings of prefabricated vertical drains (PVD) over two depth ranges, vacuum consolidation and pre-loading, and rigid inclusions.During the construction phase, the vacuum consolidation was applied for 202 to 221 days in different zones, and monitoring allowed a prediction that the future settlement, including secondary consolidation over a period of 25 years, would be within the range of 175 to 355 mm, which met the contract requirement of less than 400 mm.The power plant was completed and became operational in 2003. Monitoring of the road levels continued, as did the settlement, and in early 2010 the total settlement since the end of vacuum consolidation had reached about 800 mm. The monitoring data both during the ground treatment and for the following 7 years is presented and analysed. This is supported by numerical analysis using 3D finite element methods which shows good agreement with the measured data, and allows a preliminary explanation as to why the predictions were so far out.BACKGROUNDAfter a period of bidding and negotiation, the Eastern Power and Electric Co Ltd (EPEC), an Independent Power Producer, entered into an agreement with the Electricity Generating Authority of Thailand (EGAT) in November 1997 to sell them power. In 1999 an Engineering, Procurement and Construction (EPC) contract and an Operation and Maintenance contract were signed with a supplier to provide a gas-fired (with oil as a back-up fuel) 350 MW combined cycle power plant in Bang Bo, Samut Prakarn Province, east of Bangkok. The site of the plant at Bang Bo is located immediately to the east of the Samut Prakarn Wastewater Treatment Plant, adjacent to the Gulf of Thailand (see Figure 1) in an area of very soft to soft marine clay (Bangkok clay) having low shear strength and potential for excessive settlement. The site layout comprises the main Power Plant components of generating block, cooling towers, fuel unloading area and storage tanks, switchyard and administration block, separated by access roads."

Jan 1, 1900

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By Donald R. Clark

"Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0.Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs.The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths.Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary"

Jan 1, 2017

By Donald R. Clark

Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0. Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs. The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths. Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary design.

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Atta B. Yiadom, A. David Miller, Robert C. Kirby, Sean M. Todaro

"San Pablo Dam is a 170-foot (52-meter)-high earthfill embankment, located approximately 10 miles (16 kilometers) north of downtown Oakland, California, that impounds a 38,600 acre-feet (47.6 million m3) reservoir for customers in the East Bay Municipal Utility District's (EBMUD's) service area. Seismic upgrades were designed and constructed in 2008 through 2010. Work included removal of an existing 140,000 cubic-yard (107,000 m3) downstream buttress, which was replaced with an enlarged 300,000 cubic-yard (230,000 m3) buttress founded on alluvium and colluvium that were improved in-place using Cement Deep Soil Mixing (CDSM) technology. The site characterization for the project, design of CDSM, reuse of CDSM spoils as construction materials, and environmental permitting have been described in five previously published professional papers.This paper provides a brief summary of the design of the seismic upgrades and presents the results of measurements made during and/or after construction including the variation of CDSM strengths with time, piezometric levels within the dam and foundation soils, and seepage flow rates. These measured values are compared to the values estimated during design of the seismic upgrades.INTRODUCTIONSan Pablo Reservoir is located approximately 10 miles (16 kilometers) north of downtown Oakland, California, as shown in Fig 1. As many as 50 million gallons (200,000 m3) per day pass through the reservoir for treatment and distribution to a portion of the 1.3 million customers served by EBMUD. The dam is founded mainly on alluvium and was originally built in 1920 using materials excavated from the left and right abutments consisting of siltstone, claystone, fine-grained sandstone, mudstone, and shale that were excavated and placed using hydraulic fill methods. The dam is located within two miles (three kilometers) of the Hayward Fault which is capable of a moment magnitude 7.25 earthquake.Because of the foundation materials, construction method, and proximity to the Hayward Fault, the dam has undergone a series of seismic improvements, including the placement of a downstream compacted earth buttress in 1967 and an upstream compacted earth buttress in 1979. In 2002, the State of California Division of Safety of Dams (DSOD) requested that EBMUD evaluate the seismic stability of San Pablo Dam, following the results of a study that same year that indicated a 62 percent chance of a greater than 6.7 magnitude earthquake striking the San Francisco Bay region between 2003 and 2032. The dam was evaluated and it was concluded that portions of the underlying foundation soils may liquefy during the maximum credible earthquake which could cause the dam to become unstable."

Jan 1, 2015

By Bengt H. Fellenius

The design of pile foundations is much more commonly verified by means of a full-scale test, than is the design of other foundation units. The reason is not that our knowledge of pile behavior is more uncertain than our knowledge of other foundation types making the verification necessary, but more that the loads in a structure are more concentrated to single foundations in a structure founded on piles as opposed to structures on footings or mats. Therefore, should a pile cap fail or move, the adverse consequence of this is often drastic, as the piled structure has little freedom to transfer its need for support to other foundation units. Consequently, it becomes important to assure the design of piled foundations. In many, maybe in most instances, the static pile loading test is routine and geared toward determining an at least capacity, only. However, in these times there is an ever increasing liability of the professional, demands for increased economy of the foundation, and frequent lack of the involvement in the test of the experienced old-timer exercising good judgment. Furthermore, modern pile design is leaving the single, simple concept of capacity and requires more information from the test to assist in determining aspects of long-term behavior and settlement. Therefore, even the straight forward, routine static loading test requires improved planning, execution, and analysis.

Jan 1, 1990

By Serhan Guner, Sundar Chiluwal

Although significant research has been conducted on helical piles, there is a lack of research and official design provisions on the helical pile-to-pile cap connections. These connections may govern the global response of pile cap systems—especially in tall and light structures where uplift forces dominate the response. To improve future industry practice, the objective of this study is to understand the influence of pile-to-pile cap connections on the global behavior of concrete pile caps and develop recommendations for their efficient design. For this purpose, 108 high- fidelity nonlinear finite element simulations are conducted to quantify the influences of bracket type, embedment depths, longitudinal reinforcement percentages, shear span-to-depth ratios, and loading conditions on the load, deformation, cracking, and failure behavior of concrete pile caps. The results indicate that the design configurations involving single bracket type may result in premature concrete cracking around the anchorage zones with a 25% reduction in the uplift load capacity. The investigations also confirm that high reinforcement percentages and low shear span-to-depth ratios result in higher load resistance in all bracket types, and that the load capacities of the double and studded bracket types are similar. For applications requiring the use of lower embedment depths, it is recommended that either double or studded bracket types be used. The research findings have applicability to both helical and micro piles given that both include similar connection types. INTRODUCTION Tall and light structures may experience significant uplift forces at their foundations due to large overturning moments from wind or other lateral loads. Helical piles (e.g., Fig. 1a) can provide a cost- effective, practical, and resilient solution for resisting significant uplift forces. In order to realize the full potential of helical piles, it is imperative that the helical pile-to-pile cap connections (see Figs. 1b, c and d for examples) are properly designed to resist the applied forces. However, there is a lack of research and associated knowledge on the influence of pile-to-pile cap connection detailing on the global response of pile caps.

Jan 1, 2019

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By Noreen Tarac, Pablo Forgoso, Philipp Schober

A multiple use storage facility building is being developed in the Philippines on a peninsula that was reclaimed in the 1990s without any soil treatment. The subsoil now consists of loose to medium dense silty sand underlain by a soft to medium stiff clay. A liquefaction assessment by analytical methods have shown that the loose to medium dense silty sand yields a high potential for liquefaction and lateral spreading during pthe design level seismic event. To mitigate the risk of liquefaction and lateral spreading, as well as assure the slope stability of the shoreline, a solution utilizing a combination of ground improvement techniques by means of a Mixed-In-Place (MIPTM) Lattice Grid Wall and Stone Columns was developed and successfully executed. For the detailed seismic design, a Finite Element 3D analysis was undertaken to simulate static and dynamic actions on the buttress wall. The liquefaction assessment and settlement calculation were carried out based on analytical design approaches. For the execution of the Lattice Grid Wall, the Mixed-In-Place (MIPTM) method developed by BAUER Spezialtiefbau GmbH was applied. The stone columns were installed using the Wet Top Feed method.

Sep 8, 2021

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By Daniel P. Stare, Lucian P. Spiteri, Christopher M. Hallahan, James C. Myers

Buckeye Lake Dam was substantially remediated between 2015 and 2018 as a result of unacceptable dam safety performance. A permanent seepage cutoff, consisting primarily of a soil mixed cutoff wall (SMCW) with occasional sections of steel sheet piling, was constructed along the dam alignment. Closures were required at the terminus of the soil mix elements with existing structures or coffer cells, and at locations where new sheet piling was constructed parallel to the new soil mixed cutoff wall, creating a short circuit seepage path. The original proposed design to construct these closures included permeation grouting methods with chemical grouts. However, a combination of multiple chemical grout types, multiple grout pipes, and an extensive post-grouting verification program was required to ensure the design intent was achieved. After award of the project, the specialty grouting contractor elected to evaluate jet grouting as an alternative closure construction method. The advantages of the jet grouting option offered potential schedule and cost savings to the project as well as a superior product for seepage reduction, given the mixed soil conditions at the site. This paper presents an examination of the site conditions and project goals for the construction of the proposed closure elements for the rehabilitation of Buckeye Lake Dam. Descriptions of the original and alternative treatment methods are provided, with expected performance results. A description of the relative strengths and deficiencies of each method, as well as the feasibility and constructability of each method is provided. The implementation of the jet grouting program is presented, including a discussion of the design elements, quality control test methods, movement monitoring, and verification test methods. This paper also examines the risks associated with jet grouting and how those risks were mitigated during the grouting operations. HISTORY Buckeye Lake is situated approximately 28 miles east of Columbus, Ohio and is managed and operated by the Ohio Department of Natural Resources (ODNR) as part of the Ohio State Parks system. The lake is impounded by natural features that exist along the south and east banks of the reservoir, and by the embankment structure constructed along the north and west banks of the reservoir (see Fig. 1). The reservoir site was originally a natural swamp and the original purpose of the constructed dam and reservoir was to provide water to the Ohio and Erie Canal System. Several dam alignments and configurations were constructed during its early history; however, the original embankment is comprised of homogeneous earthen fill. The embankment is 15 ft (4.6 m) high and extends 4.1 miles (6.6 km) from the North Shore abutment along the east, continuing to the abutment at Lieb’s Island to the West. Several spillway and outlet structures exist along the embankment alignment. Most noteworthy are Seller’s Spillway and Amil Spillway. Fig. 2 is a Plan View of the embankment alignment and appurtenant structures at Buckeye Lake.

Jan 1, 2019

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017